New simple method of measuring the surface glass transition temperature of polymers

A lap‐shear joint mechanical testing method has been probed to measure the surface glass transition temperature (T) of the thick bulk films of high‐molecular‐weight polymers. As T, the temperature transition “occurrence of autoadhesion–nonoccurrence of autoadhesion” has been proposed. The influence of chain flexibility, of molecular architecture, of polymer morphology, and of chain ends concentration on the T has been investigated. The correlation between the reduction in T with respect to the glass transition temperature of the bulk (T) and the intensity of the intermolecular interaction in the polymer bulk in amorphous polymers has been found. The effect of surface roughness on T has been discussed. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 2012–2021, 2010     

The theta temperature of star polymers

We use equations derived from the blob theory to calculate the blob size and the theta temperature of star polymers. In contrast to the case of linear polymers these two parameters are calculated to depend on molecular mass for star polymers. For a given star polymer the theta temperature can be lower or higher than that of the corresponding linear polymer depending on the number and length of its branches. The results are compared with the blob model of Daoud and Cotton for star polymers. Experimental results obtained in the course of this study confirm our calculations.     

The abnormal behavior of polymers glass transition temperature increase and its mechanism

In terms of the classical theory in textbooks, the two components with phase separation in a binary polymer blend will, depending on their compatibility, have their respective Tg get closer or remain in their original values. According to the classical theory, the Tg of plastic component shall remain unchanged or move toward the lower Tg of rubber component in a rubber/plastic blend. However, ultra-fine full-vulcanized powdered rubber (UFPR) with a diameter of ca. 100 nm can simultaneously increase the toughness and the Tg of plastics, which is abnormal and is difficult to explain by classical theory. In this feature article, the abnormal behavior and its mechanism are discussed in detail.     

Correlation between glass transition temperature and chain structure for randomly crosslinked high polymers

The empirical form for the dependence, T_g(n) ≅ T_g(∞)·(1 + α/n), of the glass transition temperature T_g on the average number n of repeat units between crosslinks, is generalized for randomly crosslinked high polymers. The new form, T_g(n) ≅ T_g(∞) · [1 + c/(n·N_rot)], is based on a correlation study of data for 77 samples of 10 different sets of resins. The fitting parameter α is resolved into composition-dependent N_rot and composition-independent c terms. N_rot summarizes the average number of rotational degrees of freedom per repeat unit, and is estimated in a straightforward manner from the structure and mol fraction of each repeat unit. The value of c is found from data analysis to be 5 ± 2. The results of this work are consistent with expectations based on the entropy theory of glasses, and provide improved understanding and predictive ability for the properties of crosslinked polymers. © 1996 John Wiley & Sons, Inc.     

Application of free‐volume theory to self diffusion of solvents in polymers below the glass transition temperature: A review

Theories based on free‐volume concepts have been developed to characterize the self and mutual‐diffusion coefficients of low molecular weight penetrants in rubbery and glassy polymer‐solvent systems. These theories are applicable over wide ranges of temperature and concentration. The capability of free‐volume theory to describe solvent diffusion in glassy polymers is reviewed in this article. Two alternative free‐volume based approaches used to evaluate solvent self‐diffusion coefficients in glassy polymer‐solvent systems are compared in terms of their differences and applicability. The models can correlate/predict temperature and concentration dependencies of the solvent diffusion coefficient. With the appropriate accompanying thermodynamic factors they can be used to model concentration profiles in mutual diffusion processes that are Fickian such as drying of coatings. The free‐volume methodology has been found to be consistent with molecular dynamics simulations. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

On the relationship between microhardness and glass transition temperature of some amorphous polymers

On the basis of microhardness (H) data measured at room temperature only for a number of polymers in the glassy state, a linear correlation between H and the glass transition temperature T_g has been found (H = 1.97T_g − 571). By means of this relationship, the deviation of the H values from the additivity law for some multicomponent and/or multiphase polymeric systems can be accounted for. The latter usually contains a liquidlike soft component and/or phase with T_g below room temperature. A completely different deformation mechanism in comparison to systems with T_g above room temperature is invoked. A novel expression for the hardness of polymers in terms of crystallinity of the single components and/or phases, the T_g values, and the mass fraction of each component is proposed. This expression permits the calculation of (i) the room‐temperature H value of amorphous polymers, mainly containing single bonds in the main chain, provided T_g is known, and of (ii) the contribution of the soft liquidlike components (phases) to the hardness of the entire multiphase system. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1413–1419, 1999     

Thermally stimulated current and DSC studies of the broadened glass transition in liquid crystalline polymers

The high sensitivity of the thermally stimulated current, thermal sampling (TS) method is emphasized in a study of the breadth of the glass transition in several liquid-crystalline polymers (LCPs). Differential scanning calorimetry (DSC) was performed on all samples to further quantify the glass transition regions. For “random” copolyester LCPs with widely varying degrees of crystallinity, including highly amorphous samples, very broad glass tran-sition regions were observed. One semicrystalline alternating copolyester and a series of semicrystalline azomethine LCPs were studied as examples of structurally regular polymers. These exhibited relatively sharp glass transitions more comparable to ordinary isotropic amorphous or semicrystalline polymers. The broad glass transitions in the random copolyesters are attributed to structural heterogeneity of the chains. In one example of a moderate-crystallinity random copolyester LCP (Vectra), glass transitions ranging up to ca. 150°C in breadth were determined by the thermal sampling (TS) method and DSC. In other lower crystallinity copolyester LCPs, the main glass transition temperature as determined by DSC was comparable to that determined by TSC although cooperative relaxations of a minor fraction of the overall relaxing species were detected well below the main T_g, by the TS method and not by DSC. Rapid quenches from the isotropic melt to an isotropic glass were possible with one LCP. The anisotropic and isotropic glassy states for this LCP were found to have the same breadth of the glass transition as was determined by the TS method, although TSC and DSC show that T_g is shifted downward by ca. 15°C in the anisotropic glass as compared to the isotropic glass. © 1993 John Wiley & Sons, Inc.     

Interactions in a blend of two polymers greatly differing in glass transition temperature

Blends of poly(N‐methyldodecano‐12‐lactam) PMDL with poly(4‐vinyphenol) PVPh have been studied by the DSC and ATR FTIR methods. The difference in glass transition temperature T_g between the components is 206 °C. A single composition‐dependent T_g suggests miscibility of the system, that is, homogeneity on the scale of about 10 nm. Fitting of the equation of Brostow et al. to the T_g data indicates relatively strong specific interactions and high complexity of the system. The Schneider's equation applied separately to low‐ and high‐PVPh regions provides good agreement with experiment; the calculated curves cross at the point of PVPh weight fraction 0.27. In the low‐PVPh region, the analysis indicates weak interactions with predominance of segment homocontacts and strong involvement of conformational entropy. In the high‐PVPh region, strong specific interactions predominate and entropic effects are suppressed. Composition dependences of the heat capacity difference at T_g and the width of glass transition indicate strong interactions in the system and existence of certain heterogeneities on segmental level, respectively. According to ATR FTIR, hydrogen bonds between PVPh as proton donor and PMDL as proton acceptor induce miscibility in blends of higher PVPh content (above about 0.28 weight fraction). In low‐PVPh blends, it is conformational entropy that enables intimate intermolecular mixing. Hydrogen bonds adopt several (distorted) geometries and are on average stronger than average hydrogen bonds formed in self‐associating PVPh. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Effects of water on epoxy cure kinetics and glass transition temperature utilizing molecular dynamics simulations

Effects of water on epoxy cure kinetics are investigated. Experimental tests show that absorbed water in an uncured bisphenol‐F/diethyl‐toluene‐diamine epoxy system causes an increase in cure rate at low degrees of cure and a decrease in cure rate at high degrees of cure. Molecular simulations of the same epoxy system indicate that the initial increase in cure rate is due to an increase in molecular self‐diffusion of the epoxy molecules in the presence of water. Effects of water on the glass transition temperature (T_g) of the crosslinked thermoset are also studied. Both experiments and simulations show that water decreases T_g. Both types of results indicate that T_g effects are small below 1% water by weight, but that T_g depression occurs much quickly with increasing water content above 1%. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1150–1159     

Temperature modulated calorimetry and dielectric spectroscopy in the glass transition region of polymers

The results from temperature modulated DSC in the glass transition region of amorphous and semicrystalline polymers are described with the linear response approach. The real and the imaginary part of the complex heat capacity are discussed. The findings are compared with those of dielectric spectroscopy. The frequency dependent glass transition temperature can be fitted with a VFT-equation. The transition frequencies are decreased by 0.5 to 1 orders of magnitude compared to dielectric measurements. Cooling rates from standard DSC are transformed into frequencies. The glass transition temperatures are also approximated by the VFT-fit from the temperature modulated measurements. The differences in the shape of the curves from amorphous and semicrystalline samples are discussed.Dedicated to Professor Bernhard Wunderlich on the occasion of his 65th birthday     

Free volume microstructure of amorphous polymers at glass transition temperatures from positron annihilation spectroscopy data

The analysis of annihilation characteristics of ortho-positronium at conventional calorimetric glass transition temperatures for a series of amorphous polymers reveals empirical correlations of average lifetime of o-Ps , and of its product with a relative intensityI _3g with appropriateT _g ^DSC values. These trends in terms of free volume mean that both the average size of free volume hole entityv _hg and the fractional free volume grow with increasingT _g ^DSC . The results are discussed considering the chemical microstructure as well as possible mechanisms acting in glass transition. A relation is indicated between geometric and flexibility characteristics of chains and thev _hg andf _g parameters of free volume microstructure on the one side and potential motional processes responsible for solidification of the amorphous system on the other side.     

Elevation of the glass transition temperature in flexible‐chain semicrystalline polymers

In the idealized two‐phase model of a semicrystalline polymer, the amorphous intercrystalline layers are considered to have the same properties as the fully‐amorphous polymer. In reality, these thin intercrystalline layers can be substantially influenced by the presence of the crystals, as individual polymer molecules traverse both crystalline and amorphous phases. In polymers with rigid backbone units, such as poly(etheretherketone), PEEK, previous work has shown this coupling to be particularly severe; the glass transition temperature (T_g) can be elevated by tens of degrees celsius, with the magnitude of the elevation correlating directly with the thinness of the amorphous layer. However, this connection has not been explored for flexible‐chain polymers, such as those formed from vinyl‐type monomers. Here, we examine T_g in both isotactic polystyrene (iPS) and syndiotactic polystyrene (sPS), crystallized under conditions that produce a range of amorphous layer thicknesses. T_g is indeed shown to be elevated relative to fully‐amorphous iPS and sPS, by an amount that correlates with the thinness of the amorphous layer; the magnitude of the effect is severalfold less than that in PEEK, consistent with the minimum lengths of polymer chain required to make a fold in the different cases. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1198–1204, 2007     

Increased glass transition temperature in motionally constrained semicrystalline polymers

A large number of experimental results in the literature support and illuminate a model of behavior of chains and chain segments in the amorphous phase of semicrystalline polymers connecting the elevation of the glass transition temperature (T_g) above its normal value to several kinds of motional restrictions imposed on the chains and parts thereof. Accordingly, polymer chain, chain-segment and chain-fragment motions of all kinds comprise one or more torsions around main-chain bonds from one stable conformation to another, known as rotational isomerizations. When impediments are placed in front of thermal fluctuations and larger transversal and longitudinal motions of polymer chains, segments and shorter fragments in the amorphous phase, and the motions are thus restricted, the glass transition temperature is elevated relative to that of the same amorphous phase in the bulk under normal conditions. The obstructions may prevent either the onset of rotational isomerizations or of their completion once started. The completion of the torsional isomerizations and larger motions may be prevented by eliminating the free spaces necessary to accommodate the volumes of the interconverting chain fragments and segments even when they move in concert, or by preventing the creation of such free spaces. Another way to hinder the completion of such motions is by the introduction into the system of many rigid walls and other interfaces with strong attractive interactions with the polymer, that by geometrical constraints and attractive interactions suppress the rotational and larger motions and prevent their completion. Elimination of the necessary free volume is achievable by the application of compressive pressure, while the introduction of rigid attractive walls may be accomplished by the incorporation of crystallites, as in semicrystalline polymers, or by the addition of rigid finely comminuted foreign additives with very large surface areas or confining voids with high tortuosity. It is believed that motional restrictions imposed on the amorphous phase by the growth faces of polymer crystallites, especially in oriented semicrystalline polymers, are more effective than the restrictions imposed by the fold surfaces of these crystallites. The prevention of the onset of rotational isomerizations and larger motions may be achieved by stretching the polymer chains and chain segments in the amorphous phase and, by one means or another, pinning down the taut chains such that essentially all their rotational isomers are in the trans conformation: they cannot interconvert to the gauche conformation since it requires the chain’s end-to-end distance to decrease. Parallel alignment of relatively taut chain-segments may impose additional geometrical restrictions on both the onset and completion of rotational isomeric torsions and, of course, on longer-range motions. In all cases, the T_g of the motionally constrained parts of the amorphous phase, especially in semicrystalline polymers, is expected to rise. It is likely that the characteristic length associated with transversal motions and their suppression is R_c, the spatial distance between entanglements, which is of the same size scale, and may be the same as the tube diameter of the reptation model. Special emphasis was placed in this work on the semicrystalline polymers poly (ϵ-caprolactam) (nylon-6) and poly (ethylene terephthalate) (PET). © 1998 John Wiley & Sons, Ltd.     

Solidification of semicrystalline polymers using a variable interface temperature model

Solidification of semicrystalline materials often occurs in significantly undercooled melts. The crystal growth process in such melts is convoluted due to the fact that the interface between the solid and liquid domains of the microscopic crystals is at an unknown temperature. However, it is possible to let the temperature of this interface be unspecified and solve the problem with a semianalytical method if the growth velocity is prescribed. Solutions for the temperature profiles in both solid and liquid phases are presented in this work, along with the interface temperature, for phase change processes controlled by the kinetics of crystallization rather than diffusion processes, which is typical for polymers. The method is used for one-dimensional problems in cartesian, cylindrical, and spherical geometries that correspond to commonly found microstructures. It is found that the temperature of the interface is significantly below the equilibrium melting point and a quasi steady-state regime is reached rapidly. Comparison with the classical Neumann's solution shows that the temperature profiles are similar but the position of the interface differs considerably. © 1996 John Wiley & Sons, Inc.     

New developments in hyperbranched polymers

In the last 12 years the field of hyperbranched polymers has been well established with a large variety of synthetic approaches and fundamental studies on structure and properties of these unique materials. However, new developments involving hyperbranched materials appeared recently, for example, different synthetic strategies, new reaction mechanisms, formation of more complex architectures, a deeper understanding of the branched structure and their kinetic development, and intensive studies on the material properties and possible applications. This demonstrates the high versatility and the possibilities that are still involved in hyperbranched polymers and render it one of the most active fields in polymer science with a very promising future. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2505–2525, 2000     

Adamantyl-substituted phenolic polymers

4-(1-Adamantyl)phenol was synthesized via Friedel-Crafts reaction of 1-bromoadamantane and phenol. Substitution in the phenol para position forces polymerization to occur only in the ortho positions to give a linear polymer. Variations in formaldehyde amount, reaction time, and catalyst were evaluated. Increasing the amount of paraformaldehyde increased formation of cyclic octamer, an easily identified by-product due to its insolubility in common organic solvents. The cyclic octamer was acetylated to give a soluble model compound for comparison to acetylated polymers by IR and NMR. All of the synthetic variations employed produced low molecular weight polymers as indicated by NMR end-group analysis and SEC. The polymers showed number-average molecular weights of ca. 3000 (versus polystyrene standards by SEC), and exhibited glass transition temperatures ranging from 175–230°C, an increase of ca. 100°C over unsubstituted and para-alkyl substituted analogs. All of the samples exhibited a 10% weight loss at 400°C in nitrogen, indicating thermal stability much greater than the parent and alkyl-substituted polymers. © 1996 John Wiley & Sons, Inc.     

A systematic nomenclature for cascade polymers

Cascade (dendritic) polymers are discrete, highly branched, monodisperse polymers that possess branching patterns described by a mathematical progression. A systematic nomenclature that accurately represents these molecules is described. © 1993 John Wiley & Sons, Inc.     

High temperature silylation of glass capillary columns

This paper describes the results of a study on the deactivation of the surface of glass capillary columns by high temperature silylation (HTS). The different steps, leaching, washing, dehydration and HTS were optimized. A practical procedure yielding a high percentage of very good columns is given. The influence of leaching and HTS on the temperature stability and coating efficiency of capillary columns coated with OV-1 was studied. The inertness of the glass surface after HTS is demonstrated by several examples.