Synthesis of nylon 6–clay hybrid by montmorillonite intercalated with ϵ-caprolactam

It was found that montmorillonite was intercalated with ?-caprolactam. X-ray diffraction revealed that the chain axes of the ?-caprolactam were parallel to the montmorillonite plates. The intercalated montmorillonite was swollen by molten ?-caprolactam at 200°C. ?-Caprolactam and 6-aminocaproic acid (accelerator) were polymerized with the intercalated montmorillonite at 260°C for 6 h, yielding a nylon 6-clay hybrid. X-ray diffraction and transmission electron micrography revealed that the silicate layers of the hybrid were uniformly dispersed in the nylon 6 matrix. Mechanical properties of the hybrid were improved. The strength and the modulus of the hybrid increased compared with the previously reported nylon 6 clay-hybrid (NCH) synthesized by montmorillonite intercalated with 12-aminolauric acid. The heat distortion temperature (HDT) of the hybrid was 164°C, which was 12°C higher than that of NCH. © 1993 John Wiley & Sons, Inc.     

One-pot synthesis of nylon 6–clay hybrid

Nylon 6–clay hybrid is a molecular composite of nylon 6 and uniformly dispersed silicate layers of montmorillonite. One-pot synthesis of the hybrid was carried out by the following procedures. Montmorillonite was dispersed in water, and then ε-caprolactam, acid (phosphoric acid, hydrochloric acid, benzenesulfonic acid, isophthalic acid, trichloroacetic acid, or acetic acid), and 6-aminocaproic acid were added to the dispersion. The mixtures were reacted at 260°C for 6 h, yielding the nylon 6–clay hybrids (1potNCHs). X-ray diffraction revealed that the silicate layers of 1potNCH by phosphoric acid were uniformly dispersed in the nylon 6 matrix. The 1potNCH had excellent mechanical properties. The strength and the modulus of the hybrid increased compared with previously reported nylon 6–clay hybrid (NCH) synthesized by montmorillonite intercalated with 12-aminolauric acid. The heat distortion temperature (HDT) of the 1potNCH was 160°C, which was 8°C higher than that of NCH. In other 1potNCHs, montmorillonite had a smaller effect on the increase of those properties, and interlayer spacing of montmorillonite was observed at ca. 20 Å. © 1993 John Wiley & Sons, Inc.     

Annealing of melt-crystallized nylon 6

Effect of annealing on thermal behaviour and crystalline structure of meltcrystallized nylon 6 has been investigated.The annealing process is found to be characterized by an incubation period followed by a more or less doubling of the SAXS long spacing and of the crystallinity.The extrapolated heat of melting of the crystalline phase of nylon 6 in the-modification is 188 Jg^–1 and its extrapolated equilibrium melting temperature is 260 °C.Presented in part at 28th IUPAC Symposium on Macromolecules, Strasbourg, July, 1981.     

Kinetic analysis for hydrothermal depolymerization of nylon 6

We investigated the influences of reaction temperature, time and water density. We also investigated the reaction rate and reaction scheme which is necessary to industrialize this process from the result of hydrolysis of nylon 6 in sub- and supercritical water. The reactions were carried out at temperatures between 573 and 673 K under the estimated pressures of up to 35 MPa (water amount charged in a reactor 0.83-3.79 g/5 cm³ - reactor) for reaction times of 5-60 min. The main products of hydrolysis of nylon 6 by sub- and supercritical water are ?-caprolactam and ?-aminocaproic acid. Based on our experimental results, the reaction scheme of nylon 6 decomposition is represented. Nylon 6 was decomposed into ?-aminocaproic acid by hydrolysis followed by cyclodehydration to ?-caprolactam or decomposition further to lower molecules. At each reaction conditions, the k₁ and k₂ values were determined and the activation energy was calculated.     

The glass transition behaviour of salted nylon 6

Summary Glass transition measurements of nylon-6/lithium halides mixtures have been carried out in wide range of frequency with the aid of different experimental techniques.The results show an increase of the glass transition temperature when the salt is present and prove the larger effectiveness of lithium chloride with respect of lithium bromide.This effect, in line with the large reduction of the specific volume caused by the salt, is due to the formation of a pseudo-cross-linking between lithium ions and the carbonyl-oxygen groups of the polyamide.     

Suppressed molecular orientation in nylon 6/clay nanocomposite at large strain: Role of microvoiding

A micro‐FTIR measurement has been conducted to explore the molecular orientation of amorphous phase in the nylon 6/clay nanocomposite at large strain. Our results indicate that the molecular orientation in such a nanocomposite during stretching is lower than that observed for the pure nylon 6 counterpart, which is further evidenced by the true stress‐strain dependence. The relaxation of the molecular network, resulted from the destruction of γ‐crystals in part and mostly from microvoding (demonstrated by volume dilatation and 2D‐SAXS measurements), should be responsible for the suppressed molecular orientation in the nylon 6/clay nanocomposite. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 514–519, 2010     

Transport properties of electrospun nylon 6 nonwoven mats

In this work, we evaluate the physical properties of nylon 6 nonwoven mats produced from solutions with formic acid. Nonwoven electrospun mats from various solutions with different concentration are examined regarding their morphology, pore size, surface area, and gas transport properties. Each nonwoven mat with average fiber diameters from 90 to 500 nm was prepared under controlled electrospinning process parameters. From the results, it was observed that the fiber diameter was strongly affected by the polymer concentration (polymer viscosity). In additional the results showed that the pore size, Brunauer-Emmett-Teller (BET) surface area, and gas transport property of electrospun nylon 6 nonwoven mats were affected by the fiber diameter.     

Solid-state 13C NMR characterization of molecular orientation of hot drawn nylon 6

Two-dimensional cross polarization (CP), magic angle spinning (MAS) rotor synchronization NMR spectroscopy has been used to determine quantitatively the molecular orientational distribution function on hot-drawn Nylon 6. Both films and fibers are studied that had been thermally deformed at temperature above T_g, from 60 to 175°C at draw ratios in the range of 1-5.5. In the two-dimensional NMR spectrum, the sidebands that intrinsically originate from the chemical shift anisotropy reveal the degree of molecular orientational order. No preferential orientational order is detected for the sample without thermal deformation, and the highest degree of order is observed for samples which have been hot drawn above T_g at ratios ca. 5. Based on the aggregate model the maximum achievable order parameters are determined. © 1994 John Wiley & Sons, Inc.     

Study on solvent permeation resistance properties of nylon6/clay nanocomposite

Nylon6/clay nanocomposite is prepared by mixing organized montmorillonite with nylon6 in HAAKE mixer. Solvent permeation resistance of the nanocomposite is measured to estimate the resistance to solvent permeation. The nanocomposite shows resistance to solvent permeation superior to that of pure nylon6. In addition, the clay content was found to significantly influence the solvent permeation resistance of nylon6, and the maximum improvement in barrier properties of nylon6/clay composite was found as the clay content reached an “optimum” value. By using proper composites and processing conditions, the permeation rate of toluene and ethanol in nylon6/clay nanocomposite is about 3 and 4 times slower than that in pure nylon6 at 50 °C. Our investigation indicated that the crystalline property of nylon6 has a strong impact on the sorption and diffusion of small molecules in the polymer. The improvement in solvent barrier properties of nylon6/clay nanocomposite is attributable to incorporation of an impermeable phase such as the layered silicate, improvement in crystallinity and decrease of crystalline dimension, which are evidenced by XRD, AFM, DSC and polarized optical microscopy (POM) studies.     

Miscibility studies on blends of cellulose acetate and nylon 6

Miscibility studies on cellulose secondary acetate(CA)/Nylon 6(N6) blends have been carried out in this work. Dilute solution viscometry for the blend solutions using formic acid as the common solvent shows the existence of miscibility window.     

Effect of water absorption on the plastic deformation behavior of nylon 6

The tensile behavior of nylon 6 films has been investigated in relation to water content. Modification of chain mobility in the amorphous phase via water plasticization appears to have a determining impact on the stress-strain response. More specifically, both yield stress value and hardening behavior over a large strain domain are strikingly equivalent for samples drawn at same ΔT between draw temperature T_d and main amorphous relaxation temperature T_α. This apparent lack of thermal activation of crystal plasticity in the fibrillar transformation suggests that crystal block fragmentation proceeds via H-bond unzipping through water penetration at defective crystal interfaces.     

新型无机/有机复合柱撑粘土材料的合成与表征

以无机TiCl4／HCl制成的钛基柱撑液和十六烷基三甲基溴化胺(CTAB)为有机改性液,通过控制两种柱撑液的加入顺序以及相对含量,利用蒙脱石粘土矿物层间域的特殊化学反应场所的特性,合成得到三类复合柱撑蒙脱石材料．X射线衍射结果表明,d001晶面由于CTAB与钛基水合离子的相互作用形成粒度不同的柱撑空间而表现为两个峰值．与FT-IR光谱相比,FT-Raman光谱能够更加有效地表征和鉴定复合柱撑粘土的结构差别．采用原土无机柱撑后再有机柱撑,可以合成层间距更大的复合柱撑粘土材料．经热处理后得到锐钛型氧化钛的改性粘土材料,并且可以重新合成得到无机／有机复合柱撑的新型改性粘土材料．这些合成手段为制备新型改性粘土材料应用于环保以及化工等方面提供了借鉴．     

Synthesis and properties of polyimide–clay hybrid

A polyimide hybrid with montmorillonite clay mineral has been synthesized from a dimethylacetamide (DMAC) solution of poly(amic acid) and a DMAC dispersion of montmorillonite intercalated with an ammonium salt of dodecylamine. Montmorillonite consists of stacked silicate sheets about 2000 Å in length, 10 Å in thickness. In this hybrid, montmorillonite is dispersed homogeneously into the polyimide matrix and oriented parallel to the film surface. Thanks to this special structure, this hybrid showed excellent gas barrier properties. Only 2 wt % addition of montmorillonite brought permeability coefficients of various gases to values less than half of those of ordinary polyimide. Furthermore, this hybrid had low thermal expansion coefficient. © 1993 John Wiley & Sons, Inc.     

Structural characteristics and moisture sorption behavior of nylon‐6/clay hybrid films

The structure of nylon‐6 hybrids with synthetic or natural clays was investigated for melt‐pressed films with Fourier transform infrared spectroscopy, wide‐angle X‐ray diffraction, and differential scanning calorimetry in comparison with the nylon‐6 homopolymer. In contrast to the development of familiar α‐form crystals in plain nylon‐6 film, the hybrid films produced γ‐form crystals when nylon‐6 was conjugated with synthetic mica, whereas the hybridization with natural montmorillonite gave rise to both α‐ and γ‐crystalline modifications. The degree of crystallinity of the nylon‐6 hybrid with synthetic mica was the highest of the three series. Moisture sorption isotherms obtained for these nylon‐6‐based films were all typically sigmoid‐shaped, although the prevalence of a higher crystallinity in the hybrid samples lowered the degree of moisture regain. The sorption behavior was analyzed well in terms of the parameters of a Brunauer–Emmett–Teller multiplayer adsorption model and a Flory–Huggins treatment. It was also observed that the cluster formation of the water adsorbed into the nylon‐6 matrix tended to be restricted by the hybridization with clay. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 479–487, 2002; DOI 10.1002/polb.10106     

Influence of composition on properties of nylon 6/EVOH blends

In this work, the relationships between composition and properties of Ny6/EVOH system were examined by means of several techniques and the results were interpreted in terms of level of compatibility. Blends of different ratio of Ny6 and EVOH have been processed in a laboratory‐based film blowing extrusion apparatus. Rheological measurements, FTIR and morphological analysis, and thermal and mechanical properties were carried out. Peculiar rheological, thermal, and mechanical behaviors were observed for the blend containing 25% by weight of EVOH. At this composition, FTIR analysis has pointed out that a minimum in molecular motion is achieved as a consequence of a maximum interaction of the polar groups (amide groups of Ny6 and hydroxyl groups of EVOH) involved. Moreover, gas permeability measurements on the blown films have been performed at T = 30°C. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2445–2455, 1999     

Increase in dynamic modulus of nylon 6 fiber in repeated heating and cooling cycles under sinusoidal deformation

The repeated heating and cooling cycles under sinusoidal deformation have been investigated on nylon 6 fibers. The fibers zone-drawn twice at high temperatures were used, which have a crystallinity of 52.2% and a birefringence of 59.4×10^?3. The heating and cooling cycle was performed twice at a frequency of 110 Hz over a temperature range from 0°C to 180°C and 190°C. The crystallinity and birefringence of the treated fiber were 51.7% and 60.7×10^?3, respectively, indicating almost no changes in molecular orientation and crystallinity. However, the dynamic modulus, E′, increased steadily over whole temperature range measured. Finally, the E′ value reached 21 GPa at room temperature and 10 GPa ever at 180°C. The elongation of fiber after two cycles was only about 5%. © 1993 John Wiley & Sons, Inc.     

The electron microscope characterization of the fine structure of nylon 6: I. The supermolecular structure in melt-cast,isotropic bulk material

The application of phosphotungstic acid (PTA) as a staining agent with appropriate hardening procedures and accurate ultra-thin sectioning has enabled the direct transmission electron microscope (TEM) investigation to be carried out on the lamellar fine structure of bulk nylon 6. Details of the organization of the crystal lamellae within spherulites and other morphological structures, their shape and, especially, their dimensions were revealed and the mean structural long period was determined. Interspherulitic regions without any indication of crystalline ordering could be observed in samples which were rapidly cooled from the melt. The investigations on bulk material were completed by observations on solution-grown thin films. Optical diffraction (OD) was used for evaluating the electron micrographs; the results were compared with the data from small angle X-ray scattering (SAXS).     

Synthesis and characterization of nanostructured-segmented block copolyetheramide based on nylon6 and poly(ethylene oxide)

<正>Segmented block copolymer based on nylon6(N6) and polyethylene oxide(PEO) with stochiometric ratio was synthesized via a two-step process.The first step represents end capping of N6 in the presence of adipic acid leading to carboxy terminated N6,and the second one is polycondensation of the latter product with PEO in the presence of catalyst and thermostabilizer to form a high molecular weight multi-block copolymer.Several methods were applied to characterize the synthesized copolymer such as Fourier transform infrared spectroscopy,proton nuclear magnetic resonance spectroscopy,differential thermal analysis,differential scanning calorimetry,X-ray diffraction and atomic force microscopy. The obtained results confirmed the multi-block structure for copolymer with a very high degree of micro-phase separation. Atomic force microscopy micrographs indicated that the morphology was the dispersion of high stiffness nanostructured polyamide(PA) domains in the amorphous region of PEO matrix,which can be very important in their performance for membrane processes.     

聚酰胺/粘土纳米复合材料

聚酰胺／粘土纳米复合材料是一种新型的有机－无机纳米复合材料。在无机物含量远少于常规填充复合材料的情况下就可以具有较好的力学性能、阻隔性能等,热稳定性能也显著提高,并具有阻燃性和各向异性。是一种性能优异的、具有广泛应用前途的纳米复合材料。综述了该纳米复合材料的制备、性能和应用前景等。