首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 937 毫秒
1.
The article discusses the influence of an oligomeric resin, hydrogenated oligo (cyclopentadiene) (HOCP), on the morphology and properties of its blends with high density polyethylene (HDPE). HDPE/HOCP blends after solidification contain three phases: the crystalline phase of HDPE and two amorphous phases, one rich in amorphous HDPE and the other in HOCP. DSC thermograms and the loss modulus behaviors show that the γ transition is influenced by HOCP molecules and, in addition to the αc transition of HDPE, there is another transition that is attributed to the HOCP-rich phase. The hypothesis of the two amorphous phases is confirmed by the optical microscopy observations performed on isothermally crystallized blend films. © 1994 John Wiley & Sons, Inc.  相似文献   

2.
This article discusses the influence of the oligomeric resin, hydrogenated oligo(cyclopentadiene) (HOCP), on the morphology, and thermal and tensile mechanical properties of its blends with isotactic poly(4-methylpentene-1) (P4MP1). The P4MP1 and HOCP are found not miscible in the melt state. P4MP1/HOCP blends after solidification contain three phases: the crystalline phase of P4MP1, an amorphous phase of P4MP1, and an amorphous phase of HOCP. From optical micrographs obtained at 150°C, it is found that the solidified blends show a morphology constituted by P4MP1 microspherulites and small HOCP domains homogeneously distributed in intraspherulitic regions. DSC and DMTA results show that the blends present two glass transition temperatures (Tg) equal to the Tgs of the pure components. The tensile mechanical properties have been investigated at 20, 60, and 120°C. At 20°C both the HOCP oligomer and the amorphous P4MP1 are glassy, and it is found that all the blends are brittle and the stress–strain curves have equal trends. At 60°C the HOCP oligomer is glassy, whereas the amorphous P4MP1 is rubbery. The tensile mechanical properties at 60°C are found to depend on blend composition. It is found that the Young's modulus, the stresses at yielding and break points slightly decrease with HOCP content in the blends and these results are related to the decrease of blend crystallinity. The decrease of the elongation at break is accounted for by the presence of glassy HOCP domains that act as defects in the P4MP1 matrix, hampering the drawing. At 120°C both the amorphous phases are rubbery. It is found decreases of Young's modulus, stresses at yielding and break points. These results have been related to the decrease of blend crystallinity and to the increase of the total rubbery amorphous phase. Moreover, it is found that the blends present elongations at break equal to that of pure P4MP1. This constancy is attributed to: (a) at 120°C the HOCP domains are rubbery and their presence seems not to disturb the drawing of the samples; (b) a sufficient number of the tie-molecules and entanglements of P4MP1 present in the blends. In fact, although the numbers of tie-molecules and entanglements decrease in the blends, increasing the HOCP oligomer, they seem to be enough to keep the material interlaced and avoid earlier rupture. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1269–1277, 1997  相似文献   

3.
Thermoplastic elastomer (TPE) comprising air‐dried sheet or natural rubber (ADS or NR) and high‐density polyethylene (HDPE) was prepared by a simple blending technique. NR and HDPE were mixed with each type of phenolic compatibilizer (HRJ‐10518 or SP‐1045) or liquid natural rubber (LNR) at 180°C in an internal mixer. The mixing torque, shear stress, and shear viscosity of the blends increased with increasing amounts of NR. Positive deviation blend (PDB) for the blends containing active hydroxyl methyl phenolic resin in HRJ‐10518 or dimethyl phenolic resin in SP‐1045 was obtained. PDB was not observed for the blends without the compatibilizers or with LNR. The blends with HRJ‐10518 or SP‐1045 were compatible or partially compatible while the LNR blends were incompatible. In the phenolic compatibilized blends, NR dispersed in the HDPE matrix was found in the NR/HDPE blends of 20/80, 40/60, and 50/50 ratios. HDPE dispersed in NR matrix was obtained in the NR/HDPE blend of 80/20 ratio, and the co‐continuous phase was accomplished in the NR/HDPE blend of 60/40 ratio. The NR/HDPE blend at 60/40 ratio compatibilized with HRJ‐10518 and fabricated by a simple plastic injection molding machine exhibited higher ultimate tensile strength and elongation at break (EB). Incorporation of parafinic oil caused a decreasing tendency in tensile strength with increases in EB. The TPNRs exhibited high elastomeric nature with low‐tension set. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

4.
Nitrile butadiene rubber (NBR) was mixed with high density polyethylene (HDPE) thermoplastics with different ratio namely (100/20), (100/40), (100/60) and (100/80). The obtained blends were subjected to gamma irradiation with varying dose from 50 to 250 kGy. The induced crosslinking and hence the improvement in the different properties were followed up as a function of irradiation dose. Mechanical properties as tensile strength, tensile modulus at 50 % elongation, elongation at break percent, permanent set and hardness were carried out as a function of irradiation dose and blend ratio. Moreover, physical properties namely, gel fraction % and swelling number were found to improve with the increase of irradiation dose up to 250 kGy and with the increase of the content of HDPE in blend. Moreover, presence of NBR enhances the shrinking properties of the obtained blend which can be used as a good heat shrinkable material.  相似文献   

5.
The dynamic mechanical behaviour of high impact polystyrene (PS-HI), styrene/butadiene/styrene block copolymer (SBS) and PS-HI + SBS blends were investigated. Dynamic mechanical analysis (DMA) was performed in the temperature range −100°C to 100°C. The primary viscoelastic functions were determined. The copolymers PS-HI and SBS as well as PS-HI+SBS blends were investigated in creep-fatigue regime and relaxation at temperatures 25, 30, 35, 40 and 45°C. Dynamic mechanical behavior of PS-HI, SBS and PS-HI + SBS blends depends on the copolymer and blends composition, the hard phase content, time and temperature. With the decrement of the hard phase PS concentration, the loss tangent of the soft phase increases while the loss tangent of the hard phase and the storage modulus decrease. All samples have a single Tg of the hard phase and a single Tg of the soft phase. The glass transition temperatures decrease as the content of the PS phase decreases. At the constant load the creep values increase and those of creep modulus decrease over a period of time, for all examined samples. These effects are more pronounced in samples with lower content of hard phase and at higher temperatures. The time-temperature correspondence principle was applied to create master curves for the reference temperature 25°C for the creep modulus of PS-HI, SBS and PS-HI + SBS blends on a time scale far outside of the range measured by DMA experiments. These results enable us to predict the useful life of our copolymers and their blends in a wide range of time and temperature.  相似文献   

6.
The capillary extrusion of polypropylene (PP) and high-density polyethylene (HDPE) immiscible blends was studied in this work by rheo-particle image velocimetry (Rheo-PIV). The PP/HDPE blends were prepared by single screw extrusion and extruded through a transparent capillary die at a temperature of 200 °C and concentrations of 80/20, 60/40, 40/60 and 20/80 wt%, respectively. PIV measurements described accurately the flow behavior of PP/HDPE blends and revealed continuous velocity profiles in the die, without macroscopic phase separation, for all the blends in the resolution range of the PIV technique. The flow behavior of all the blends was shear-thinning (power-law) type and their viscosities laid in between the values corresponding to the neat polymers and increased in an exponential way along with the concentration of the highest viscosity component in the blend (HDPE). Also, it was found that the extruded blends acquired a stratified morphology and that HDPE mitigates extrudate distortions in PP, meanwhile PP eliminates slip and flow instabilities in HDPE by migrating to the region of highest shear stresses in the die. Migration of PP to the capillary wall was corroborated by Raman spectroscopy measurements on the periphery of solid extrudates. Finally, via calculations of the density of the molten blends under flow using the velocity profiles in the die, we show that the homopolymers are compatible in the molten state and follow a simple inverse relation for their density, and an exponential one for their viscosity.  相似文献   

7.
 In an attempt to produce biodegradation materials, poly(vinyl alcohol) (PVA)–starch (ST) blends were prepared by gelation/crystallization from semidilute solutions in dimethyl sulfoxide (Me2SO) and water mixtures and elongated up to 8 times. The content of mixed solvent represented as Me2SO/H2O (volume percent) was set to be 60/40 assuring the greatest drawability of PVA homopolymer films. The PVA/ST compositions chosen were 1/1, 1/3, and 1/5. The elongation up to 8 times could be done for the 1/1 blend but any elongation was impossible for blends whose ST content was beyond 50%. When the blends were immersed in water at 20 or 83 °C, the solubility became considerable for an undrawn blend with 1/5 composition and a drawn 1/1 blend with λ=8. To avoid this phenomenon, cross-linking of PVA chains was carried out by formalization under formaldehyde vapor. Significant improvement could be established by the cross-linking of PVA chains. For the 1/1 blend, the amount of ST dissolved in water at 23 °C was less than 3% for the undrawn state and 25% for the drawn film. The decrease in the ST content was enough for use as biodegradation materials. Namely, the water content relating to the biodegradation in soil is obviously different from such a serious experimental condition that a piece of blend film was immersed in a water bath. At temperatures above 0 °C, the storage modulus of the formalization blends became slightly higher than those of the nonformalization blends. The Young's modulus of the drawn films with a draw ratio of 8 times was 2 GPa at 20 °C. Received: 23 June 2000 Accepted: 30 October 2000  相似文献   

8.
Summary: A series of polyethylene (PE) blends consisting of a high density polyethylene (HDPE) and a linear low density polyethylene (LLDPE) with a butene-chain branch density of 77/1000 carbon was prepared at different concentrations. The LLDPE only crystallized below 50 °C, therefore, above 80 °C and below the melting temperature of HDPE, only HDPE crystallized in the PE blends. A specifically designed multi-step experimental procedure based on thermal analysis technique was utilized to monitor the liquid–liquid phase separation (LLPS) of this set of PE blends. The main step was first to quench the system from the homogeneous temperatures and isothermally anneal them at a prescribed temperature higher than the equilibrium melting temperature of the HDPE for the purpose of allowing the phase morphology to develop from LLPS, and then cool the system at constant rate to record the non-isothermal crystallization. The crystallization peak temperature (Tp) was used to character the crystallization rate. Because LLPS results in HDPE-rich domains where the crystallization rates are increased, this technique provided an experimental measure to identify the binodal curve of the LLPS for the system indicated by increased Tp. The result showed that the LLPS boundary of the blend measured by this method was close to that obtained by phase contrast optical microscopy method. Therefore, we considered that the thermal analysis technique based on the non-isothermal crystallization could be effective to investigate the LLPS of PE blends.  相似文献   

9.
The system formed by isotactic polypropylene (iPP) and hydrogenated oligo(cyclopentadiene) (HOCP) is investigated in order to study the influence of the composition and thermal history on the morphology, phase structure, miscibility and thermal and mechanical properties of the blends. A phase diagram presenting both the lower and the upper cloud point curves is proposed. It is shown that these blends assume different morphologies and consequently present diverse thermal and dynamic-mechanical behaviours depending on quenching processes from one-phase region or two-phase region. From the analyses of the results of optical microscopy, WAXS, DSC and DMTA techniques it is found that: blend films, quenched from the melt of one-phase region to room temperature, contain one amorphous phase and iPP in smectic form; moreover they are transparent and possess a reduced permeability to oxygen and aroma; conversely when the samples are quenched from the melt of two-amorphous phase region there is the formation of two amorphous phases (the iPP-rich phase and the HOCP-rich phase) and at room temperature the iPP crystallizes in the monoclinic α form.  相似文献   

10.
HDPE is commonly used in pipelines and piping for industrial and societal infrastructure. Like most polymers, HDPE's mechanical properties are sensitive to temperature and show time dependent properties. The temperature effect on both the short and long term compressive and tensile behavior of HDPE, in a combined manner, have not been investigated thoroughly in the past. Especially the constitutive behavior of HDPE, incorporating temperature effects on its long and short term behavior, could be essential when designing such infrastructural components. Hence, the temperature effect on the short and long term response in tension and compression of HDPE is investigated in this study. The short term tensile and compressive stress-strain behavior at 23, 40, 60, and 80 °C were obtained through experiments at constant displacement rate and temperature. Tensile and compressive stress relaxation (e.g. long term) behavior at 23, 40, 50, 60, 70, and 80 °C were investigated through stress relaxation tests. The experimental results from the short term tests showed that both the tensile and compression moduli and yield strength of HDPE decrease linearly with the increase in temperature. It is also shown from the long term test that relaxation modulus in tension and compression are highly dependent on temperature. Based on the experimental results, the constitutive three network model (TNM) was calibrated and implemented in a FEA model, which was then validated through a three point bending (3 PB) relaxation test with a prescribed temperature profile. The FEA model and the calibrated model results agree markedly well with the experimental results, which indicates that the model can be used reliably to predict the temperature dependent short and long term behavior of HDPE in design and analysis of HDPE components.  相似文献   

11.
Summary: Two kinds of interpolymer complexes as soluble or precipitate of different structures were obtained in both THF and butan-2-one as common solvents by monitoring the hydrogen-bonding density within homoblends of poly(n-butyl methacrylate-co-4-vinylpyridine) (BM4VP) and poly(n-butyl methacrylate-co-methacrylic acid) (BMMA). A viscometry study confirmed such differences between these two types of interpolymer complexes from the behavior of the reduced viscosity of their blend solutions with feed blend composition. Qualitative and quantitative analyses of the interactions that occurred between these copolymers of relatively bulky side chain length containing various amounts of methacrylic acid and 4-vinylpyridine were carried out by FTIR. The fraction of associated pyridine groups to the carboxylic groups of the BMMA increases as the content of these latter increases in the BMMA/BM4VP blends. The obtained results also showed that the fractions of associated pyridine within the BMMA25/BM4VP26 blends are higher than those within BMMA18/BM4VP19 or BMMA8/BM4VP10. The FTIR analysis of a selected BMMA18/BM4VP19 1:1 ratio, carried out from 80 °C to 160 °C, above the glass transition temperatures of the two constituents of the blend, confirms the presence of strong hydrogen bonding interactions between the pyridine and the carboxylic groups within these blends even at 160 °C. A LCST is expected to occur at higher temperature as shown from the progressive decrease of the fraction of the associated pyridine.  相似文献   

12.
In this work, carbon nanotube (CNT) was used to fabricate poly(vinylidene fluoride) (PVDF)/high density polyethylene (HDPE) blend-based nanocomposites via a Haake mixer. Scanning electron microscopy confirmed that the CNT was mainly selectively located in the HDPE dispersed domains. Thermogravimetric analysis revealed that CNT addition improved the thermal stability of the blend (up to 61 °C increase at 3-phr CNT loading at 40 wt% loss) in air environment. Differential scanning calorimetry results revealed the enhanced nucleation of individual PVDF and HDPE upon crystallization in the composites; the presence of CNT inceased the stability of PVDF crystals. CNT addition increased the heat distortion temperature of the blend by up to 27 °C at 3-phr CNT loading. The complex viscosity and storage modulus increased due to the CNT pseudo-network formation in the reduce-sized HDPE phase of the composites. The rigidity of the blend was significantly improved after the addition of CNT. The impact strength of the blend increased by up to 66% after 2-phr CNT loading, and the electrical resistivity of the blend decreased by up to nine orders at 3-phr CNT loading due to the double percolation-like morphology formation.  相似文献   

13.
A systematic investigation of the dynamic mechanical properties of high-density polyethylene (HDPE)/high-impact polystyrene (HIPS)/copolymer blends was carried out. Blends of 80/20 weight percent of HDPE/HIPS were prepared in the melt state at 180°C in a batch mixer. Synthesized pure diblock (H77) and tapered diblock (H35) copolymers of hydrogenated polybutadiene (HPB) and polystyrene (PS) were added at different concentrations (1, 3, and 5 wt %), and the dynamic mechanical properties were investigated. The results show that: (1) both the tapered and the pure diblock copolymers enhance the phase dispersion and the interphase interactions; (2) structure and molecular weight are both important parameters in the molecular design of copolymers; (3) important effects occur when only small amounts of copolymer are added (up to the interface saturation concentration SC); (4) a micellar structure formation is possible when the copolymer is in excess in the blend; (5) the effect of the copolymer structure on the SC and the critical micellar concentration (CMC) is more pronounced than the effect of molecular weight. These concentrations are found to be lower for the tapered diblock copolymer. The analysis of the dynamic mechanical thermal analysis (DMTA) results obtained for the 20/80 HDPE/HIPS blend leads to the conclusion that the copolymers also enhance the interactions between heterogeneous phases. Similar conclusions based on electron microscopy were reported in the literature. DMTA shows great potential to relate macroscopic observations to the state of a copolymer in an immiscible blend.  相似文献   

14.
The nanocomposites of polyamide 6 (PA6)/poly(methyl methacrylate) (PMMA)/non-functionalized and functionalized [carboxylic acid (COOH) and hydroxyl (OH)] single wall carbon nanotubes (SWCNTs) were prepared in mass ratios of 79.5/19.5/1, 49.5/49.5/1, and 19.5/79.5/1 by melt–mixing method at 230 °C. The PA6/PMMA blends with mass ratios of 80/20, 50/50, and 20/80 served as references. The Fourier transform infrared analyses of nanocomposites showed the formation of hydrogen bond interactions among PA6, PMMA, and OH and COOH functional groups of SWCNTs. The nanocomposites and blends had higher thermal stability with respect to the PMMA. The differential scanning calorimeter (DSC) curves showed that the nanocomposites and blends exhibited two T g values at around 51 and 126 °C for PA6 and PMMA, respectively. About 20 °C early crystallization was observed in nanocomposites compared to the blends. The dynamic mechanical analysis (DMA) results suggested that among all the compositions of blends and nanocomposites, storage modulus (E′) was higher for PMMA-rich blends and nanocomposites. At 25 °C, the E′ values were higher for blends and nanocomposites compared to the neat PA6. The tan δ curves indicated that the more heterogeneity of the hybrid nature resulted in PA6/PMMA/SWCNTs-OH or SWCNTs-COOH with 79.5/19.5/1 mass ratio nanocomposites compared to the PA6/PMMA with 80/20 mass ratio blend. The higher T g values of PA6 and PMMA were observed in DMA studies compared to the DSC studies for PA6 and PMMA as neat and in blends and nanocomposites. The significant improvements in crystallization of nanocomposites were considered resulting from achieving better compatibility among the polymer components and carbon nanotubes.  相似文献   

15.
边新超  陈学思 《高分子科学》2016,34(9):1070-1078
Poly(ether urethane)s(PEU), including PEUI15 and PEUH15, were prepared through chain-extension reaction of poly(ethylene glycol)(PEG-1500) using diisocyanate as a chain extender, including isophorone diisocyanate(IPDI) and hexamethylene diisocyanate(HDI). These PEUs were used to toughen polylactide(PLA) by physical and reactive blending.Thermal, morphological, mechanical and aging properties of the blends were investigated in detail. These PEUs were partially compatible with PLA. The elongation at break of the reactive blends in the presence of triphenyl phosphate(TPP)for PLA with PEUH15 or PEUI15 was much higher than that of the physical blends. The aging test was carried out at-20 °C for 50 h in order to accelerate the crystallization of PEUs. The PEUs in the PLA/PEU blends produced crystallization and formed new phase separation with PLA, resulting in the declined toughness of blends. Fortunately, under the aging condition,although PEUH15 in blends could also form crystallization, the reactive blend of PLA/PEUH15/TPP(80/20/2) had higher toughness than the other blends. The elongation at break of PLA/PEUH15/TPP(80/20/2) dropped to 287% for the aging blend from 350% for the original blend. The tensile strength and modulus of PLA/PEUH15/TPP blend did not change obviously because of the crystallization of PEUH15.  相似文献   

16.
The linear viscoelastic properties of polystyrene polyethylene (PS/PE) blends have been investigated in the molten state. For concentrations of the dispersed phase equal to 30 vol %, the blends exhibited a droplet‐matrix morphology with a volume‐average diameter of 5.5 μm for a 70/30 PS/PE blend at 200 °C and 14.7 μm for a 30/70 PS/PE blend at 230 °C. Enhanced elasticity (G′) for both blends, in the terminal zone, compared to the modulus of the matrix (PS and PE, respectively) was observed. This is related to the deformation of the droplets in the matrix phase and hence to the interfacial forces between the blend components. The results for these uncompatibilized blends are shown to be in agreement with the predictions of the emulsion model of Palierne. These predictions were used to obtain the interfacial tension between PS and PE, which was found to be between 2 and 5 mN/m at 200 °C and 4 ± 1 mN/m at 230 °C. Independent interfacial tension measurements using the breaking‐thread method resulted in a value of 4.7 mN/m and 4.1 mN/m at 200 °C and 230 °C for the respective blends. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1359–1368, 2000  相似文献   

17.
The properties of diglycidyl ether of bisphenol-A epoxy resin toughened with poly(ether sulfone ether ketone) (PESEK) and poly(ether sulfone) (PES) polymers were investigated. PESEK was synthesised by the nucleophilic substitution reaction of 4,4’-difluorobenzophenone with dihydroxydiphenylsulfone using sulfolane as solvent and potassium carbonate as catalyst at 230 °C. The T g–composition behaviour of the homogeneous epoxy resin/PESEK blend was modelled using Fox, Gordon–Taylor and Kelley–Bueche equations. A single relaxation near the glass transition of epoxy resin was observed in all the blend systems. From dynamic mechanical analysis, the crosslink density of the blends was found to decrease with increase in the thermoplastic concentration. The storage modulus of the epoxy/PESEK blends was lower than that of neat resin, whilst it is higher for epoxy/PES blends up to glass transition temperature, thereafter it decreases. Scanning electron microscopic studies of the blends revealed a homogeneous morphology. The homogeneity of the blends was attributed to the similarity in chemical structure of the modifier and the cured epoxy network and due to the H-bonding interactions between the blend components. The fracture toughness of epoxy resin increased on blending with PESEK and PES. The increase in fracture toughness was due to the increase in ductility of the matrix. The thermal stability of the blends was comparable to that of neat epoxy resin.  相似文献   

18.
Polyamide 66 (PA66)/high density polyethylene (HDPE) blends having miscible structure were produced by compatibilization of HDPE grafted with maleic anhydride (HDPE‐g‐MAH). Mechanical and tribological properties of blends in different compositions were tested. It was found that the polymer blends greatly improved the mechanical properties of PA66 and HDPE. Blending HDPE with PA66 significantly decreased the friction coefficient of PA66; the friction coefficients of blends with different compositions were almost the same and approximately equal to that of pure HDPE; the blends with 80 vol % PA66 exhibited the best wear resistance. The transfer films, counterpart surfaces, and wear debris formed during sliding were investigated by Scanning Electron Microscopy (SEM), and Differential Scanning Calorimetry (DSC) analysis was further carried out on wear debris. These investigations indicated that the thermal control of friction model is applicable to PA66/HDPE blend, that is the friction coefficient of blend is governed by the HDPE component, which possesses a lower softening point relative to the PA66 component in this system. The wear mechanism of PA66/HDPE blend transforms from PA66 to HDPE as the HDPE content increases. PA66, as the component with higher softening point, increases the hardness of blend, enhances the ability of blend to form a transfer film on the counterface, and inhibits the formation of larger belt‐like debris of HDPE, at the same time, the presence of self‐lubricating HDPE in the system decreases the friction coefficient and the frictional heat, all of these factors are favorable for the wear resistance of PA66/HDPE blend. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2514–2523, 2005  相似文献   

19.
The mechanical and physical properties of blends based essentially on nitrile butadiene rubber (NBR) and different ratios of high density polyethylene (HDPE) up to 25 parts per hundred part of rubber (phr) before and after electron beam irradiation were investigated. The values of tensile strength (TS), tensile modulus at 50% elongation (M50), hardness and gel fraction % (GF%) of NBR/HDPE blends were increased with both irradiation dose and by increasing the content of HDPE in the blends. On the other hand, the values of elongation at break (E b ) were decreased with both irradiation dose and the content of HDPE in the blends. By loading NBR/HDPE (100/25) blend with ethylene vinyl acetate (EVA) copolymer the mechanical and physico-chemical properties were improved. Moreover, the degree of improvement is proportional to the loading content of EVA.  相似文献   

20.
YaPeng  傅强 《高分子科学》2004,(5):431-438
Metallocene-catalyzed short chain branched polyethylene (SCBPE) was blended with LDPE, HDPE, PS, EPDM and iPP in the weight proportions of 80 and 20. The crystallization and mechanical properties of these blends were studied by PLM, DSC and DMA. It has been observed in PLM that SCBPE/LDPE, SCBPE/HDPE and SCBPE/EPDM can form band spherulites whose band width and size are both smaller than that of the pure SCBPE. Tiny crystallites are observed in the completely immiscible SCBPE/PS blend. The crystallites in SCBPE/iPP are very small and only irregular spherulites are seen. The crystallization kinetics and mechanical properties of SCBPE are greatly affected by the second polyolefin, but in a different way, depending on the phase behavior and the modulus of the second components. SCBPE may be phase miscible in the melt with HDPE, LDPE and EPDM and co-crystallize together with HDPE or LDPE during cooling. A big change of crystal morphology and crystallization kinetics is seen in SCBPE/iPP blend compared with pure SCBPE and the lowest tanδ is also seen for this system. DMA results show that the tensile modulus of the blends has nothing to do with phase behavior, but only depends on the modulus of the second component.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号