Reactive surfactants in heterophase polymerization. VIII. Emulsion polymerization of alkyl sulfopropyl maleate polymerizable surfactants (surfmers) with styrene

The copolymerization of styrene with two polymerizable surfactants (surfmers) based on maleic acid (dodecyl sodium sulfopropyl maleate and tetradecyl sodium sulfopropyl maleate) was studied in batch emulsion polymerizations. The surfmer conversion was obtained by serum replacement with water and subsequent analysis of the recovered, unreacted surfmers with two-phase titration. It was found that both surfmers copolymerized well with styrene and their partial conversion was higher than that of styrene. These results are contradictory to what was found before in the literature using ultrafiltration with methanol, and the differences are explained on the basis of oligomer formation: The oligomers formed are detected if the latices are washed with methanol. It was found that at the end of the polymerization (almost complete conversion of both styrene and surfmer) only 45% of the surfmer groups were present on the particle surface, which is in agreement with a high conversion of the surfmer at the beginning of the reaction. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 2561–2568, 1997     

无皂乳液聚合法制备P(St-MMA-SPMAP)单分散乳胶颗粒

利用无皂乳液聚合 ,分别用一步法和两步法合成了单分散的聚 (苯乙烯 甲基丙烯酸甲酯 甲基丙烯酸丙基磺酸钾 ) (P(St MMA SPMAP) )乳胶颗粒 .在该聚合体系中 ,当水溶性磺酸基单体SPMAP的浓度小于 17mmol L时 ,为均相成核过程 ,能制备单分散的乳胶颗粒 .其中 ,用两步法制备的乳胶颗粒相互之间无粘连 .此外 ,还对一步法合成苯乙烯 甲基丙烯酸甲酯 甲基丙烯酸辛基磺酸钠 (P(St MMA SOMAS) )乳胶颗粒进行了初步研究 .     

Macromolecule — Metal complexes based on salts of unsaturated mono- and dicarboxylic acids: Synthesis and characterization

The radical polymerization and copolymerization of salts of unsaturated carboxylic acids were used for the production of metal-containing polymers. The kinetic peculiarities and copolymerization parameters were estimated. The synthesis and structure of transition metal acrylates, maleates, fumarates, and itaconates are discussed. The influence of the metal atom on salt reactivities and reaction rates is observed.     

Emulsifier-free emulsion copolymerization of styrene and sodium styrene sulfonate

The kinetics of the emulsifier-free emulsion copolymerization of styrene and sodium styrene sulfonate have been examined over a range of comonomer compositions. The rate of polymerization was found to increase dramatically in the presence of small amounts of sodium styrene sulfonate. This increase is attributed to the increased number of particles formed when sodium styrene sulfonate was present and to a gel effect enhanced by ion association. At low concentrations of functional comonomer, where a monodisperse product was obtained, a homogeneous nucleation mechanism of particle generation is proposed. At higher concentrations, broader and then bimodal size distributions were obtained, and this is ascribed to significant aqueous phase polymerization of sodium styrene sulfonate. The water-soluble homopolymer is supposed to act as a locus of polymerization. The occurrence of this aqueous phase side reaction and the generation of secondary particles makes impossible the preparation of highly sulfonated polystyrene latexes by batch or seeded batch emulsion copolymerization.     

Miniemulsion copolymerization of vinyl acetate and butyl acrylate. IV. Kinetics of the copolymerization

The copolymerization kinetics of conventional emulsions and miniemulsions of 50:50 and 25:75 molar ratios vinyl acetate–butyl acrylate monomer mixtures were studied using sodium hexadecyl sulfate as surfactant. Hexadecane was the cosurfactant used in the preparation of the miniemulsions, and ammonium persulfate was the initiator used in the polymerizations. The rate of polymerization showed four regions which extended to different conversions depending on the type of emulsion used (conventional or miniemulsion). The rate of polymerization for the miniemulsion process was always slower than for the conventional process. The dependence of the rate on the initiator concentration was higher for the miniemulsion process. The number of particles nucleated in the miniemulsion copolymerization process was lower than in the conventional emulsion copolymerization process. The initiator and surfactant concentration dependence of the number of particles were 0.8 and 0.25 for the miniemulsion copolymerization process and 0.0 and 0.68 for the conventional emulsion copolymerization process respectively. These effects were attributed to the different particle nucleation mechanism operating in each process.     

表面活性单体存在下的MMA／BA乳液共聚合（Ⅱ）：聚合动力？…

研究了表面活性单体「磺化－十二醇－烯丙基甘油－丁二酸酯钠盐（ＺＣ－Ｌ）」的用量对ＭＭＡ／ＢＡ／ＺＣ－Ｌ乳液聚合速率和粒径的影响,用Ｃｏｒｌｔｉｒ ＬＳ２３０型激光粒径分析仪测定聚合过程中乳液的粒径和粒径分布变化,并与ＭＭＡ／ＢＡ无皂乳液聚合及十二烷基苯磺酸钠存在下的ＭＭＡ／ＢＡ乳液聚合作了比较。「ＺＣ－Ｌ」〈ＣＭＣ时,成核机理为均相成核机理,乳胶粒需依靠粒子间的凝聚来提高表面电荷密度而稳定;「ＺＣ     

表面活性单体存在下的MMA/BA乳液共聚合(Ⅱ)聚合动力学及机理

研究了表面活性单体[磺化-十二醇-烯丙基甘油-丁二酸酯钠盐(ZC-L)]的用量对MMA/BA/ZC-L乳液聚合速率和粒径的影响,用CoulterLS230型激光粒径分析仪测定聚合过程中乳液的粒径和粒径分布变化,并与MMA/BA无皂乳液聚合及十二烷基苯磺酸钠存在下的MMA/BA乳液聚合作了比较.[ZC-L]CMC时,成核机理包括均相成核和胶束成核机理,生成的粒子因吸收体系中的表面活性单体而稳定存在.     

High-Solids Content Waterborne Polymer-Clay Nanocomposites

Summary: Waterborne polymer clay nanocomposites (WPCN) were prepared by emulsion and miniemulsion copolymerization of butyl acrylate and methyl methacrylate with enhanced mechanical, thermal and barrier properties for coating applications. Emulsion polymerization was used to synthesize WPCN using pristine Na-MMT (sodium montmorillonite) and miniemulsion polymerization to prepare the WPCNs when the pristine clay was organically modified and hence its incorporation into the polymerization loci was not guaranteed by the conventional emulsion polymerization technique. Both techniques allowed preparing stable nanocomposite latexes of BA/MMA copolymers with partially exfoliated morphologies as demonstrated by wide X-ray difraction (WAXD) and transmission electron microscope (TEM) measurements. Furthermore, latexes with solids contents up to 45 wt% and manageable viscosities were prepared for the first time using seeded semibatch emulsion polymerization.     

Emulsion copolymerization behavior of α-methylstyrene with methacrylonitrile

The emulsion copolymerization behavior of α-methylstyrene with methacrylonitrile is described. The effects of polymerization temperature, potassium persulfate initiator concentration, sodium lauryl sulfate emulsifier concentration on copolymer yield, molecular weight, and rate of copolymerization are described. The copolymer was found to have an azeotropic composition at 43 mole-% AMS. Reactivity ratios were determined to be 0.06 and 0.28 for AMS and MAN, respectively.     

聚氨酯/聚丙烯酸酯复合乳液的研制进展

概述聚氨酯－聚丙烯酸酯复合乳液的制备方法。特别对聚氨酯－聚丙烯酸酯复合乳液共聚法作了较为系统的介绍和讨论。     

Miniemulsion copolymerization of vinyl acetate and butyl acrylate. I. Differences between the miniemulsion copolymerization and the emulsion copolymerization processes

Differences between the emulsion copolymerization and miniemulsion copolymerization processes, in terms of emulsifier adsorption, emulsion stability, polymerization kinetics, copolymer composition and dynamic mechanical properties were studied for the comonomer mixture of 50:50 molar ratio vinyl acetate (VA+)—butyl acrylate (BuA), using sodium hexadecyl sulfate (SHS) as a surfactant and hexadecane (HD) as a co-surfactant. The use of hexadecane with the appropriate SHS initial concentration led to a higher adsorption of surfactant, smaller droplet size, higher stability of the emulsions, lower polymerization rates, and larger latex particle size. The copolymer composition during the initial 70% conversion was found to be less rich in Vac monomer units for the miniemulsion process. The dynamic mechanical properties of the copolymer films showed less mixing between the BuA-rich core and the VAc-rich shell in the miniemulsion latexes compared to the conventional latex films.     

The emulsion copolymerization of styrene and sodium styrene sulfonate

The emulsion copolymerization of styrene and sodium styrene sulfonate has been shown to be a feasible preparative route to ionomeric sulfonated polystyrene. The properties of these copolymers are reported elsewhere. The copolymerization rate was found to be dramatically enhanced when compared to that for the emulsion copolymerization of styrene under identical conditions. This copolymerization was studied in detail and two mechanisms were proposed to account for these rate differences. An increase in the number of polymerizing particles in the copolymerization with consequent rate enhancement was substantiated by electron microscopy. However, the data indicate that the rate differences cannot be fully accounted for by this effect. In addition, a gel effect is proposed as a second contributor to the enhanced rate. This gel effect is believed to result from the intermolecular association of the incorporated metal sulfonate units in the growing polymer particles. When a third monomer that plasticizes the ionic interactions is used the polymerization rate decreases. This supports the gel effect hypothesis.     

P(MMA-M12-BPMA)乳液的合成及紫外吸收性能

以甲基丙烯酸甲酯(MMA)、可聚合乳化剂马来酸酐衍生物磺酸钠(M12)和可聚合紫外线吸收剂2-羟基-4-(3-甲基丙烯酰氧基-2-羟基丙氧基)苯甲酮(BPMA)为原料,采用乳液聚合方法制备了P(MMA-M12-BP-MA)共聚物乳液。通过转化率、红外光谱、以及紫外吸收光谱测定,分别研究了M12含量对聚合反应速率的影响、所得共聚产物的结构、以及共聚物乳液和共聚物紫外吸收特性。结果表明,随M12含量增大,聚合反应速率增加;BPMA含量增大有利于提高共聚物乳液和共聚物紫外吸收性能。     

Emulsion polymerization of vinyl acetate using a polymerizable surfactant. I. Kinetic studies

A polymerizable surfactant, sodium dodecyl allyl sulfosuccinate (TREM LF-40; Henkel) and its nonpolymerizable counterpart were used in comparative studies of the emulsion polymerization of vinyl acetate. The conversion-time behavior differed for the two surfactants; the TREM LF-40 showed a decrease in the polymerization rate with increasing concentration while its hydrogenated derivative showed the opposite behavior, the rate increasing with increasing surfactant. Particle size analysis revealed a decreasing particle size with increasing surfactant concentration for both series of reactions. An explanation for the seemingly ambiguous results obtained for the polymerizable surfactant was sought by examining the reactivity of its vinyl group in copolymerization with vinyl acetate and its allylic group in a chain transfer reaction. The results suggest that both the copolymerization and chain transfer reactions can lead to the observed reduction in polymerization rate with increasing TREM LF-40 concentration. © 1992 John Wiley & Sons, Inc.     

自由基嵌段共聚合新进展

本文引用５０多篇文章，按引发方式不同从顺序引发剂，ｉｍｉｆｅｒｔｅｒ法，高分子引发剂法和自由基性聚合等几方面综述了自由基嵌段共聚合近１０年来的新进展。     

Synthesis of Polyvinylacetate‐Sodium Montmorillonite Hybrids by Emulsion Polymerization in the Presence of Anionic Surfactants

The emulsion polymerisation of vinyl acetate (VAc) in presence of sodium dodecylsulphate (SDS) and sodium montmorillonite (NaMMT) is used in order to achieve polymer‐clay hybrids. The influence of the polyvinylacetate (PVAc), SDS, and PVAc‐SDS complex on the NaMMT structure also was investigated. The VAc emulsion polymerization rate exhibits a maximum as the NaMMT concentration increases. The XRD patterns correspond to hybrids with intercalated structure. If a water soluble comonomer, ammonium sulphato ethylmethacrylate (ASEMA) is used for copolymerization with VAc, a exfoliated hybrid structure (from XRD spectra) is obtained. The solid materials were analysed by TGA, FTIR, XRD, SEM, and TEM.     

Emulsion polymerization of vinyl acetate using a polymerizable surfactant. III. Mathematical model

A mathematical model was developed to aid in the further understanding of the growth of latex particles in the emulsion polymerization of vinyl acctate using a polymerizable surfactant, sodium dodecyl allyl sulfosuccinate (TREM LF-40). The model incorporates the main features of the system observed experimentally: copolymerization in the aqueous phase, at the particle surface, and chain transfer to TREM LF-40. The reactions at the particle/water interface and, more specifically, the chain transfer to TREM LF-40 leading to a decrease in the average number of radicals per particle, was found to be the most significant mechanism for explaining the difference in kinetic results found for TREM LF-40 and its nonpolymerizable counterpart. The copolymerization of vinyl acetate with TREM LF-40 was also shown to slow the overall polymerization rate. However, the copolymerization alone was not sufficient to account for the decreased polymerization rates observed experimentally. A combination of copolymerization and chain transfer to TREM LF-40 was found to provide a good fit of the experimental results. © 1993 John Wiley & Sons, Inc.     

离子型共聚单体参与下的全氟丙烯酸酯无皂乳液共聚

离子型共聚单体参与下的全氟丙烯酸酯无皂乳液共聚;全氟烷基丙烯酸酯;无皂乳液;离子型共聚单体     

Emulsion polymerization of vinyl acetate using a polymerizable surfactant. II. Polymerization mechanism

The mechanism of growth of latex particles in the emulsion polymerization of vinyl acetate using a polymerizable surfactant, sodium dodecyl allyl sulfosuccinate (TREM LF-40; Henkel) was investigated. Both the aqueous phase and the particle/water interface were found to be loci for the copolymerization of TREM LF-40 with vinyl acetate. Competitive growth experiments using TREM LF-40 and its nonpolymerizable derivative were conducted to separate the effects of aqueous phase and particle surface. Particle size analysis of the seeded and unseeded polymerizations coupled with kinetic results suggested that the reactions at the particle/water interface are more important and that the particle size of the latexes is a key parameter controlling the polymerization rate through copolymerization and chain transfer to the polymerizable surfactant at the particle surface. A decrease in particle size lead to an increase in the amount of TREM LF-40 polymerized at the particle surface and to a decrease in polymerization rate. © 1992 John Wiley & Sons, Inc.     

Copolymerization of polar and non-polar monomers in direct and inverse emulsion systems

Some problems connected with the use of monomers with different solubilities in water and oil phases for copolymerization in direct and inverse (micro)emulsions are discussed. We have shown that by choosing appropriate model systems which can simulate specific effects connected with the transfer of reactants between various phases and swelling ability of polymer particles, one can contribute to the answering the questions of the propagation locus (loci) of copolymerization and of its (their) history during emulsion copolymerization as well as to recognize the effect of the nature of the interlayer in the inverse (micro)emulsion system in relation to the kinetics and mechanism of the copolymerization process and structure of the copolymer formed. The method was demonstrated on the examples of seeded methyl methacrylate emulsion polymerization, of the emulsion copolymerization of styrene and divinylbenzene and of the inverse (micro)emulsion copolymerization of acrylamide and methyl methacrylate and/or acrylamide and styrene.