Copolymerization and Copolymers of Styrene N-(2,4,6-Tribromophenyl) Maleimide with Styrene

Kinetic studies of the free radical copolymerization of N-(2,4,6- tribromophenyl) maleimide (TBPMI) with styrene in solution were carried out. The thermal and flammability characteristics of the resulting polymers were also investigated. The monomer reactivity ratios were found to be r ₁ = 0.006 ± 0.0026 (TBPMI) and r ₂ = 0.086 ± 0.0023, and the activation energy of the copolymerization reaction was E_a = 73.6 kJ/mol. The resulting copolymers showed an alternating structure regardless to the monomer feed composition. The molecular weights of the copolymers obtained are relatively high and gradually increase by increasing the TBPMI fraction in the feed, whereas the T_g's showed similar values (540 K) for the equimolar ratio of the comonomers. The course of copolymerization up to high conversion was followed by microcalorimetry and is characterized by a remarkable increase of the initial reaction rate as the fraction of TBPMI was increased; it is also higher at higher total monomer concentrations. However, the overall conversion decreases when the fraction of TBPMI is higher than the equimolar ratio. The thermal stability of the alternating copolymers is higher than that of polystyrene, and their mixture showed appreciable flame-retardant properties, as demonstrated by a limiting oxygen index measurement.     

Radiation-induced copolymerization of styrene/n-butyl acrylate in the presence of ultra-fine powdered styrene–butadiene rubber

Styrene (St)/n-butyl acrylate (BA) copolymers were prepared by two-stage polymerization: St/BA was pre-polymerized to a viscous state by bulk polymerization with initiation by benzoyl peroxide (BPO) followed by ⁶⁰Co γ-ray radiation curing. The resultant copolymers had higher molecular weight and narrower molecular weight distribution than conventional methods. After incorporation of ultra-fine powdered styrene–butadiene rubber (UFSBR) with a particle size of 100 nm in the monomer, the glass transition temperature (T_g) of St–BA copolymer increased at low rubber content. Both the St–BA copolymer and the St–BA copolymer/UFSBR composites had good transparency at BA content below 40%.     

Dispersion copolymerization of styrene and other vinyl monomers in polar solvents

Dispersion polymerization is a very attractive method for preparing micrometer‐size monodisperse polymer particles. The applications of microspheres have been greatly expanded by the use of copolymers. Here, the dispersion copolymerization of styrene and seven other vinyl monomers was carried out in polar solvents. The effect of the different comonomers on the particle size was systematically investigated. The particle size first decreased and then increased with an increasing fraction of acrylamide in the monomer feed, and at a higher fraction of such a comonomer, only a gel‐like polymer was obtained. The particle size also increased with the increase in the contents of the hydrophilic comonomers in the monomer mixtures, and the copolymer molecular weight decreased meanwhile. Although the amount of the hydrophobic comonomer in the monomer mixture changed, the particle size was hardly affected. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 555–561, 2001     

Copolymers of 1-methylcyclopropene

1-Methylcyclopropene (MCP) copolymerizes rapidly with acrylic and vinyl monomers to form soluble, high molecular weight products containing enchained cyclopropane rings. The high electron availability in the cyclopropene double bond promotes one-to-one alternating copolymerization with sulfur dioxide, maleic anhydride, acrylic acid, acrylonitrile, dialkyl fumarates and acrylic esters. Nonalternating copolymers are obtained with vinyl chloride and vinyl acetate, and attempted copolymerization fails entirely with styrene, α-methylstyrene and isoprene. This pattern of copolymerization reactivity resembles that of highly compressed ethylene. Methylcyclopropene copolymers have high glass temperatures in spite of the small size of the MCP unit. The combination of high T_g and small size allows preparation of copolymers with high T_g having a wide range of ductilities and cohesive energy densities.     

Thermal and mechanical properties of random copolymers of diisopropyl fumarate with 1‐adamantyl and bornyl acrylates with high glass transition temperatures

We report the thermal, optical, and mechanical properties of random copolymers produced by radical copolymerizations of diisopropyl fumarate (DiPF) with 1‐adamantyl acrylate (AdA) and bornyl acrylate (BoA). The effects of a methylene spacer included in the main chain and bulky ester alkyl groups in the side chain on the copolymer properties are discussed. The produced copolymers are characterized by NMR and UV–vis spectroscopies, size exclusion chromatography, thermogravimetric analysis, differential scanning calorimetry, and dynamic mechanical analysis (DMA). The copolymerization rate and the molecular weight of the copolymers increase with an increase in the acrylate content in feed during the copolymerization (M_w = 25–110 × 10³). The onset temperature of decomposition (T_d5) and the glass transition temperature (T_g) of the copolymers also increase according to the content of the acrylate units (T_d5 = 296–329 °C and 281–322 °C, T_g = 80–133 °C and 91–106 °C for the copolymers of DiPF with AdA and BoA, respectively). Transparent and flexible copolymer films are obtained by a casting method and their optical properties such as transparency and refractive indices are investigated (n_D = 1.478–1.479). The viscoelastic data of the copolymers are collected by DMA measurements under temperature control. The storage modulus decreases at a temperature region over the T_g value of the copolymers, depending on the structure and amount of the acrylate units. The sequence structure of the copolymers is analyzed based on monomer reactivity ratios and composition in order to discuss the copolymer properties related to chain rigidity and sequence length distribution. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 288–296     

Semicontinuous heterophase copolymerization of styrene and acrylonitrile

The synthesis of styrene‐acrylonitrile copolymers by semicontinuous heterophase polymerization is reported here. The effect of feed composition at a fixed addition rate of monomer mixture on kinetics, particle size, polymer content, and molar masses, was studied. This process permits the synthesis of nanolatexes containing narrow size‐distribution particles with number‐average diameter (D_n) of about 18 nm, polymer content as high as 23 wt %, and copolymer‐to‐surfactant weight ratios between 23 and 25, depending on monomer feeding rate, which are larger than those reported for microemulsion copolymerization of several comonomers. Copolymers with homogeneous composition similar to the feeding monomers composition were obtained thorough the reaction, which is difficult to achieve by batch polymerization. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of polyphenylquinoxaline copolymers via aromatic nucleophilic substitution reactions of an A‐B quinoxaline monomer

A self‐polymerizable quinoxaline monomer (A‐B) has been synthesized and polymerized via aromatic nucleophilic substitution reactions. An isomeric mixture of self‐polymerizable quinoxaline monomers—2‐(4‐hydroxyphenyl)‐3‐phenyl‐6‐fluoroquinoxaline and 3‐(4‐hydroxyphenyl)‐2‐phenyl‐6‐fluoroquinoxaline—was polymerized in N‐methyl‐2‐pyrrolidinone (NMP) to afford high molecular weight polyphenylquinoxaline (PPQ) with intrinsic viscosities up to 1.91 dL/g and a glass‐transition temperature (T_g) of 251 °C. A series of comonomers was polymerized with A‐B to form PPQ/polysulfone (PS), PPQ/polyetherether ketone (PEEK), and PPQ/polyethersulfone (PES) copolymers. The copolymers readily obtained high intrinsic viscosities when fluorine was displaced in NMP under reflux. However, single‐electron transfer (SET) side reactions, which limit molecular weight, played a more dominant role when chlorine was displaced instead of fluorine. SET side reactions were minimized in the synthesis of PPQ/PS copolymers through mild polymerization conditions in NMP for longer polymerization times. Thus, the T_g's of PES (T_g = 220 °C), PEEK (T_g = 145 °C), and PS (T_g = 195 °C) were raised through the incorporation of quinoxaline units into the polymer. Copolymers with high intrinsic viscosities resulted in all cases, except in the case of PPQ/PEEK copolymers when 4,4′‐dichlorobenzophenone was the comonomer. © 2001 John Wiley & Sons, Inc. J Polym Sci A Part A: Polym Chem 39: 2037–2042, 2001     

Synthesis and Enzymatic Degradation of Nylon 66 Copolymers with Poly(Ethyleneglycol)s

Abstract

Nylon 66 (N66) copolymers were prepared by melt polycondensation of adipic acid and hexamethylenediamine with 5–80 mol% poly(ethylene glycol) (PEG), where the molecular weight (MW) of PEG was 200–1000. The reduced specific viscosity of the copolymers was increased by the copolymerization. The crystallinity and melting temperature (T _m) of N66 components decreased with increasing PEG content, but T _m depression of copolymers at the same mole content decreased with increasing MW of PEG, suggesting that the copolymer structures are not of the random type but of the block type at the higher MW of PEG. The water absorption increased with increasing PEG content, and its increase was much higher at the higher MW of PEG. The enzymatic degradation was estimated by the weight loss of copolymer films in the buffer solution with and without a lipase at 37°C. The weight loss was enhanced appreciably by the presence of a lipase, and increased abruptly at higher PEG content, which was correlated to water absorption and the concentration of ester linkages. The enzymatic degradation of these N66 copolymers was much higher than that of previously reported PET copolymers with PEG. The abrupt increase of weight loss by alkali hydrolysis was fairly comparable to that of water absorption.     

Radical copolymerization of styrene and alkyl methacrylates: monomer reactivity ratios and thermal properties

Copolymers containing styrene and alkyl methacrylate (n-butyl-, n-hexyl-, or stearyl methacrylate) at different compositions have been prepared by radical copolymerization. The monomer reactivity ratios were estimated using the Finemann-Ross, the inverted FR and the Kelen-Tüdos graphical methods. Structural parameters of the copolymers were obtained calculating the dyad monomer sequence fractions. The effect of the size of the alkyl methacrylate on the copolymer structure is discussed. The glass transition temperature, T_g of the copolymers with butyl and hexyl methacrylate was examined in the frame of several theoretical equations allowing the prediction of these T_g values. The best fit was obtained using methods that take into account the monomer sequence distribution of the copolymers. The copolymers of styrene with stearyl methacrylate exhibited the characteristic melting endotherm, due to the crystallinity of the methacrylate sequences and the polystyrene glass transition temperature.     

The Role of Components in Waterbased Microsphere Acrylic Psa Adhesive Properties

In this paper the batch suspension copolymerization of ethyl acrylate/2 ethyl hexylacrylate (EA/2-EHA) for production of suspension-based microsphere acrylic pressure sensitive adhesives (PSA) is presented. The effects on the adhesion properties of PSA different process (reaction temperature and stirrer speed) as well as chemical parameters (amount of EA, initiator concentration) are discussed. The conversion was monitored in-line using Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FTIR) spectroscopy and the results were compared with the standard gravimetrical method. The glass transition temperatures (T_g) of the PSAs were measured using differential scanning calorimetry (DSC) technique, while molecular weight distribution (MWD) was determined by gel permeation chromatography (GPC). The adhesion properties of PSAs were characterized via the measurements of tack, peel adhesion and peel strength. The results of the experiments have shown that the kinetics of the suspension polymerization for production of PSAs is significantly affected by temperature of polymerization and the initiator concentration, but are shown to be relatively independent of the EA amount and the stirrer speed. The tack, peel and shear strength depend on the mean particle size and particle size (PS) distribution (PSD) and T_g. The mean particle size and PSD depend primarily on the stirrer speed during the PSA synthesis process, while the T_g is most affected by amount of EA used for the synthesis. The results have also shown a rather unexpected relationship between MWD of the PSAs and the applicative properties: tack, peel and shear are seen to be increasing to the decreasing values of weight average MWD, which is the exact opposite of the previously published research. The most likely explanation for this relationship is the formation of a gel during the synthesis of PSA.     

Cinnamate‐functionalized poly(ester‐carbonate): Synthesis and its UV irradiation‐induced photo‐crosslinking

A functionalized cyclic carbonate monomer containing a cinnamate moiety, 5‐methyl‐5‐cinnamoyloxymethyl‐1,3‐dioxan‐2‐one (MC), was prepared for the first time with 1,1,1‐tri(hydroxymethyl) ethane as a starting material. Subsequent polymerization of the new cyclic carbonate and its copolymerization with L ‐lactide (LA) were successfully performed with diethyl zinc (ZnEt₂) as initiator/catalyst. NMR was used for microstructure identification of the obtained monomer and copolymers. Differential scanning calorimetry (DSC) was used to characterize the functionalized poly(ester‐carbonate). The results indicated that the copolymers displayed a single glass transition temperature (T_g) and the T_g decreased with increasing carbonate content and followed the Fox equation, indicative of a random microstructure of the copolymer. The photo‐crosslinking of the cinnamate‐carrying copolymer was also demonstrated. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 161–169, 2009     

分散共聚法制备窄分布P(St-co-nBA)微球

用分散共聚法制得窄分布苯乙烯(St)和丙烯酸正丁酯(nBA)的共聚物微球.采用1H-NMR、DSC、FTIR、SEM、LS等对共聚物的结构、形态、性能进行表征,考察了初始单体配比、温度、稳定剂浓度、分散介质极性、引发剂对微球粒径、粒径分布及转化率的影响.实验结果表明,初始单体比nBA/St增大,微球粒径增大,分布变宽,...     

Synthesis and characterization of graft copolymers of poly(vinyl chloride) with styrene and (meth)acrylates by atom transfer radical polymerization

Graft copolymers of poly(vinyl chloride) with styrene and (meth)acrylates were prepared by atom transfer radical polymerization. Poly(vinyl chloride) containing small amount of pendent chloroacetate units was used as a macroinitiator. The formation of the graft copolymer was confirmed with size exclusion chromatography (SEC), ¹H NMR and IR spectroscopy. The graft copolymers with increasing incorporation of butyl acrylate result in an increase of molecular weight. One glass transition temperature (T_g) was observed for all copolymers. T_g of the copolymer with butyl acrylate decreases with increasing content of butyl acrylate.     

有机硅改性丙烯酸酯共聚乳液合成方法及胶膜性能的研究

用一次投料法、单体乳液滴加法和引发剂滴加法有机硅改性丙烯酸酯共聚乳液，聚合过程、胶粒形态及乳液稳定性的观测结果表明：单体乳液滴加法是合成该类乳液的最佳方法，研究了单体乳液滴加法中有机硅含量与聚合反及胶膜性能的关系，结果表明：有机硅含量在１５％以下时，聚合反应可以顺利进行，胶膜性能不仅依赖于聚合时有机硅单体的总量，而且还依赖于有机硅单体中活性硅氧烷所占的比例。     

Novel random poly(propylene isophthalate/adipate) copolyesters: Synthesis and characterization

Poly(propylene adipate) (PPA) and poly(propylene isophthalate/adipate) (PPI-PPA) random copolymers of various compositions were synthesized in bulk and characterized in terms of chemical structure and molecular weight. Furthermore, the thermal behavior was examined by thermogravimetric analysis and differential scanning calorimetry. All the polymers showed a good thermal stability. At room temperature they appeared as semicrystalline materials, except the copolymers containing 20 and 30 mol% of PI units: the main effect of copolymerization was a lowering in the amount of crystallinity and a decrease of melting temperature with respect to homopolymers. The crystalline phase of PPI and PPA was evidenced at high content of propylene isophthalate or propylene adipate units, respectively. Amorphous samples were obtained after melt quenching and an increment of T_g as the content of PI units is increased was observed. This behavior was explained as due to the stiff phenylene groups in the polymeric chain. The Wood equation was found to describe well T_g-composition data. Lastly, the presence of a rigid-amorphous phase was evidenced in the copolymers, differently from PPA homopolymer.     

Batch and semicontinuous emulsion copolymerization of vinyl acetat–butyl acrylate. I. Bulk,surface, and colloidal properties of copolymer latexes

Vinyl acetate (VAc)–butyl acrylate (BuA) comonomer mixtures with various composition were polymerized by batch and semicontinuous emulsion polymerization processes. PVAc and PBuA homopolymer latexes as well as the (VAc-BuA) copolymer latexes were characterized with respect to particle size, molecular weight, acid end groups on particle surfaces, and colloidal stability against electrolytes. The surface and colloidal properties of these latexes were also compared before and after aging and acid hydrolysis. The average particle size of batch latexes was independent of copolymer composition, whereas for semicontinuous latexes it decreased with increasing BuA content and was always lower than that of the corresponding batch latex. The molecular weight distribution (MWD) for batch latexes was narrower and much less dependent on composition than that of the semicontinuous latexes; bimodal MWD was found in most semicontinuous latexes with a substantial amount of low MW fraction. The total weak and strong acid end groups on particle surfaces for semicontinuous latexes is higher, and more dependent on composition, than the batch latexes. Acid-induced hydrolysis results in a drastic change in the type and concentration of the surface groups of the semicontinuous latex particles. Colloidal stability against electrolytes showed that both electrostatic (due to surface acid groups) and steric [due to surface poly(vinyl alcohol)] mechanisms are contributing. However, for semicontinuous latexes, increasing PVAc content above 50 mol % resulted in a proportional increase and ultimately dominant role of steric stabilization. The results were interpreted in terms of differences in reactivity ratios and water solubilities of the two monomers and their effects on the locus of initiation and growth in the two polymerization processes, as well as the monomer sequence within the polymer chain and degree of homogeniety of the copolymer composition within the particle.     

Synthesis and polymerization studies of N-cyanomethanimine monomers

New imine monomers containing C-aryl and N-cyano substituents were synthesized and polymerized by both radical and anionic initiation. Homopolymerization yielded low molecular weight polymers (M_n < 2100). Higher yields were obtained with anionic initiation rather than radical initiation. Radical initiated copolymerization with p-methoxystyrene gave low yields of low molecular weight copolymers. Radical initiated copolymerization with methyl acrylate gave copolymers of 15,000–,32,000 molecular weight in moderate yields, but with rather low incorporation of the imine monomer. The C-substituent affected the anionic and free radical reactivity similarly. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2703–2710, 1997     

从乙烯与丙烯酸二茂铁甲酰氧基乙酯共聚物制备碳纳米材料

使用乙烯和丙烯酸二茂铁甲酰氧基乙酯(FcEA)为单体,合成了乙烯与丙烯酸二茂铁基乙酯共聚物[P(E-co-FcEA)].以P(E-co-FcEA)作为前驱体,通过改变裂解条件,自催化制得系列碳纳米材料.     

Effect of the Poly(Methyl Methacrylate) Molecular Weight on the Mechanical Properties BisGMA/TEGDMA Semi-interpenetrating Polymer Networks

Abstract

The effect of poly(methyl methacrylate) [PMMA], with different molecular weights on the mechanical properties of a polymerized BisGMA/TEGDMA base monomer resin was investigated. With the aid of acetone solvent, PMMA could be readily dissolved in BisGMA/TEGDMA mixtures. The addition of PMMA can significantly improve the compressive strengths and decrease the Knoop hardness values of the BisGMA/TEGDMA/PMMA semi-IPNs. The thermal expansion coefficients rapidly increased before T_g, and decreased after T _g. The observed properties could be attributed to the effect of the molecular weight of the PMMA on the phase structures of the semi-IPNs.     

The effect of sodium methacrylate on the soapless emulsion copolymerization of methyl methacrylate and n-butyl acrylate

The soapless emulsion polymerization of methyl methacrylate (MMA) and n-butyl acrylate (BA) containing various concentrations of sodium methacrylate (NaMA) or methacrylic acid (MMA) is studied. The hydrosoluble yields in final latexes are not larger than 1.3–5%, depending on the concentration of NaMA used. Below 25% conversion, the change of conversion with reaction time follows the square rule and the particle size is proportional to the 2/3 power of time. Above 25% conversion, serious gel effect occurs, and the conversion follows the seventh power on time and the growth of particle diameter obeys the 2.5 power on time. The multiple glass transition (T_g) occur below 20% conversion, where monomer droplets exist. NaMA added induces more T_gs. The effect of molecular weight of the copolymers obtained on T_g (even the molecular weight distributions were shown to be shouldertype bimodal) is estimated to be insignificant. Thus, the heterogeneity of copolymer compositions for multiple T_gs is ascribed to be caused from neither the molecular weight heterogeneity nor the shifts in compositions due to the difference of the monomer reactivity ratios. Referring to the results mentioned, we assume the sublayer surrounding the particle, rich with SO₄^? and COO^? groups, and the concentration gradients of monomers in particles to illustrate particle morphology. In addition, the relatively hydrophilic sublayer is proposed to be closely relative with the occurrence of the composition heterogeneity in particles.