Rotor-synchronized two-dimensional 13C CP/MAS NMR studies of the orientational order of polymers. I. High-performance ultrahigh molecular weight polyethylene fibers

The orientational order of three morphological components, identified previously as two crystalline components, C₁ and C₂, and an amorphous component, A of four polyethylene fibers, including two gelspun ultrahigh molecular weight (PE-I and PE-II) and two meltspun moderate molecular weight (PE-D and PE) polyethylene fibers are further analyzed by rotor-synchronized two-dimensional ¹³C CP/MAS (ROSMAS) nuclear magnetic resonance (NMR) techniques. Our results indicate that the orientational order of these components differ substantially among themselves in a given fiber and among different fibers of the same component. Values of β_1/2, the polar angle at which the orientational distribution function (ODF) P 〈β〉 decays to half its maximum, are determined to be: 18° (C2 of PE-II), 21° (C2 of PE-I), 29° (C2 of PE-D), 31° (C1 of PE-I) and 50° (C2 of PE). No orientational sideband can be detected for component A, suggesting that the A component is due to the amorphous domain. The implication of this results and the technical limit of this technique are analyzed. © 1993 John Wiley & Sons, Inc.     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

An evoluted bio-based 2,5-furandicarboxylate copolyester fiber from poly(ethylene terephthalate)

A series of bio-based poly(ethylene terephthalate-co-ethylene 2,5-furandicarboxylate) (PEFT) fibers was prepared via the industrially feasible melt-spinning and hot-drawing process. The effect of 2,5-furandicarboxylic acid (FDCA) content on the fibers properties was studied using differential scanning calorimetry, wide-angle X-ray diffraction, sound velocity, tensile, and boiling water shrinkage tests. It was found that the PEFT fibers showed comparable or superior tenacity to the PET fibers under the same conditions, especially the PEFT-4 fibers exhibited the highest tenacity (2.3, 2.9 cN/dtex for the drawn PET and PEFT-4 fibers prepared at the same take-up speed of 2500 m/min and a fixed draw ratio of 1.6). Moreover, the boiling water shrinkage of the PEFT fibers was quite close to that of the PET fibers under the same conditions, showing that the PEFT fibers were comparable to the PET fibers in heat resistance. The results indicated that the bio-based PEFT fibers would be a feasible alternative for the PET fibers, in terms of sustainability, processability, and mechanical properties. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 320–329     

Evaluation of the orientation coefficient for the c axis in poly(ethylene terephthalate) fibers

The literature methods for the determination of the mean of the crystallite orientation distribution for the c axis, that is of the orientation coefficient f_c, for poly(ethylene terephthalate) (PET), based on the azimuthal scan of the (1 05) reflection, are reviewed. These methods appear unsuitable for samples presenting the “tilted orientation”; that is, the molecular chain axis inclined by some degrees with respect to the fiber axis, as frequently occurs for PET fibers. A new method for the determination of f_c for PET, also based on the azimuthal scan of the (1 05) reflection (which can be applied also to samples with “tilted orientation”), is proposed. This method implies as a first step the determination of the tilt angle, for which the complete fiber pattern is required. A possible simplifying assumption, which allows use of the sole azimuthal (1 05) profile and makes the method also applicable to poorly oriented samples (for which the determination of the tilt angle is not easy), is also discussed. © 1995 John Wiley & Sons, Inc.     

Structural features of crystallized poly(ethylene terephthalate) polymers

Polyethylene terephthalate (PET) is a widely used polymeric material. In this work, the microstructural features before and after the solid‐state polymerization (SSP) of several DuPont PET products were investigated by low‐voltage scanning electron microscopy (LV‐SEM) and atomic force microscopy (AFM). The microstructural features on the cross section of various PET samples included crystallites, voids, boundaries, defects, and amorphous phases. The SEM images revealed layered and stepped structural features at the micron and 10‐micron scales that are highly crystallized at the near‐edge region of the cross section for both linear and branched PET samples after the SSP process. The AFM images demonstrate that the degree of crystallization for the linear and branched PET samples increases gradually from the central area to the edge on the cross section. The linear crystallized PET has a higher degree of orientation than the branched crystallized PET in the 10‐micron to micron scales, but their crystalline structures have no significant differences in the submicron to nanometer scales. The PET crystallization process occurs when the molecular chains in the amorphous phase are aligned and folded to form straight molecular chains at the nanometer scale, and small crystallites are formed. The crystallites aggregate and align together into a polygon rod‐like‐shaped crystallites at the submicron scale. Finally, large crystallites at the micron size are formed that appear on the edge area of the cross section. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 245–254, 2002     

NMR study of ester-interchange reactions during melt mixing of poly(ethylene terephthalate)/poly(butylene terephthalate) blends

The occurrence of ester-interchange reactions during PET/PBT blend processing has been confirmed by ¹³C-NMR measurements. The limitations of the method for precise quantification of the extent of reaction between high molecular weight polyester blends have also been pointed out. Titanium alkoxide has been confirmed as an efficient catalyst, and, within experimental precision, the stabilizing effect of triphenyl phosphite addition has been demonstrated. © 1996 John Wiley & Sons, Inc.     

Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

Miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) blends by transesterification

The effects of transesterification on the miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) were studied. Blends were obtained by solution precipitation at room temperature to avoid transesterification during blend preparation. The physical blends and transesterified products were analyzed by wide-angle x-ray scattering, differential scanning calorimetry, and nuclear magnetic resonance spectroscopy. It was found that the physical blends are immiscible and when the extent of transesterification reaches 50% of the completely randomized state, independent of blend composition, the blends are not crystallizable and show a single glass transition temperature between those of starting polymers. The interchange reactions were significantly influenced by annealing temperature and time but negligibly by blend composition. © 1996 John Wiley & Sons, Inc.     

Water sorption/desorption kinetics in poly(ethylene naphthalene-2,6-dicarboxylate) and poly(ethylene terephthalate)

Water sorption/desorption experiments were carried out on films (～ 220 μm thick) of amorphous poly(ethylene naphthalene-2,6-dicarboxylate) (PEN) stored in ambient conditions for different periods of time (0.5-4 years) and of poly(ethylene terephthalate) (PET) with different degrees of crystalinity levels (0-29%) by means of FTIR spectroscopy. Water sorption/desorption kinetics follows Fick's law for all samples investigated. Water sorption isotherms, obtained from gravimetric methods, indicate a larger sorption capacity in the case of PEN materials. The apparent diffusion coefficients (D) are larger in the case of PET samples. The observed D values decrease with storage time (physical aging) of PEN samples and with the crystallinity of PET samples. © 1995 John Wiley & Sons, Inc.     

In situ drawing of high molecular weight poly(ethylene terephthalate) in subcritical and supercritical CO2

The effects of draw conditions were studied for initially amorphous melt‐spun poly(ethylene terephthalate) fibers in the presence of subcritical and supercritical (SC) CO₂. Both in situ and posttreatment mechanical behavior along with morphological characteristics were investigated. Fibers soaked in subcritical CO₂ could be drawn to 30% higher draw ratios (DRs) compared with fibers that were cold‐drawn. In situ force response measured with a custom apparatus showed that fibers in subcritical CO₂ had no measurable resistance to deformation until strain hardening occurred. In contrast, fibers drawn in SC CO₂ displayed a yield response, a significant decrease in ductility, and a significant difference in postyield behavior. Fibers drawn in subcritical CO₂ showed slightly lower tensile properties compared with cold‐drawn samples whereas fibers treated in SC CO₂ had much lower tensile properties because of the limited DR achieved. X‐ray diffraction studies indicated that CO₂ enhances the development of the crystalline phase compared with cold‐drawn samples. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1881–1891, 1999     

Unique crystalline structure and performance of poly(ethylene terephthalate) melt spun fibers

Modification of the threadline dynamics has effected significant alternations in the structure and improvements in the properties of high-speed melt spun poly(ethylene terephthalate) (PET) fibers. Key process parameters extant in the threadline dynamics, such as temperature, tensile stress, and deformation time, were independently controlled through proper implementation of on-line perturbations. The placement of a liquid isothermal bath in close proximity to the spinneret in the melt spinning threadline provided tremendous increase in the spinning stress while at the same time controlled the filament temperature corresponding to development of the desired fiber structure. Characterization of the fiber structure and physical properties has been carried out using birefringence measurements, density, shrinkage, x-ray diffraction, DSC, FTIR spectroscopy, and tensile tests. The results provided sufficient evidence to support the existence of a unique crystalline morphology that led to the significantly improved tensile properties and excellent dimensional stability of the resulting fibers. This unique crystalline morphology was typically characterized by the presence of a larger amount of extended chain segments and an enhanced molecular connectivity. ©1995 John Wiley & Sons, Inc.     

High‐pressure DTA of poly(butylene terephthalate), poly(hexamethylene terephthalate), and poly(ethylene terephthalate)

Pressure effect on the melting behavior of poly(butylene terephthalate) (PBT) and poly(hexamethylene terephthalate) (PHT) was studied by high‐pressure DTA (HP‐DTA) up to 320 and 530 MPa, respectively. Cooling rate dependence on the DSC melting curves of the samples cooled from the melt was shown at atmospheric pressure. Stable and metastable samples were prepared by cooling from the melt at low and normal cooling rates, respectively. DTA melting curves for the stable samples showed a single peak, and the peak profile did not change up to high pressure. Phase diagrams for PBT and PHT were newly determined. Fitting curves of melting temperature (T_m) versus pressure expressed by quadratic equation were obtained. Pressure coefficients of T_m at atmospheric pressure, dT_m/dp, of PBT and PHT were 37 and 33 K/100 MPa, respectively. HP‐DTA curves of the metastable PBT showed double melting peaks up to about 70 MPa. In contrast, PHT showed them over the whole pressure region. HP‐DTA of stable poly(ethylene terephthalate) (PET) was also carried out up to 200 MPa, and the phase diagram for PET was determined. dT_m/dp for PET was 49 K/100 MPa. dT_m/dp increased linearly with reciprocal number of ethylene unit. The decrease of dT_m/dp for poly(alkylene terephthalate) with increasing a segmental fraction of an alkyl group in a whole molecule is explained by the increase of entropy of fusion. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 262–272, 2000     

Recovery as a measure of oriented crystalline structure in poly(ether ester)s based on poly(ethylene oxide) and poly(ethylene terephthalate) used as shape memory polymers

Poly(ether ester)s consisting of poly(ethylene oxide) and poly(ethylene terephthalate) segments, EOET copolymers, could be used as shape memory polymers (SMP). Crystalline structural characters of the copolymers during the memory process were investigated by dynamic mechanical analysis, differential scanning calorimeter, wide-angle X-ray diffraction, polarizing microscopy, and recovery measurements. PEO crystals in stretched EOET copolymer preferentially oriented along fiber axis or stretch direction. During stretching, the structure of the copolymer undertake a transformation from spherulite to fiber, resulting in a crystalline morphology similar to shish-kebab, and recovery properties of stretched EOET samples were dependent on as-described crystalline structural characters that can be influenced by draw ratio. Driving forces for contraction come from the oriented chains, and only oriented or extended chains can be contributive to the recovery of deformation; these extended chains involve both crystalline and amorphous segments. The recovery process in shape memory behavior was noticed to be deorientation of oriented chains due to thermodynamic entropy effect, and was divided into three stages. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 101–112, 1999     

Interval kinetic gravimetric sorption of acetone in random copolymers of poly(ethylene terephthalate) and poly(ethylene 2,6-naphthalate)

Interval sorption kinetics of acetone in solvent cast films of random poly(ethylene terephthalate)-co-(ethylene 2,6-naphthalate) (PET-co-PEN) are reported at 35°C and at acetone pressures ranging from 0 to 7.3 cm Hg. Polymer composition is varied systematically from 0% to 50% poly(ethylene 2,6-naphthalate). Equilibrium sorption is well described by the dual-mode sorption model. Interval sorption kinetics are described using a two-stage model that incorporates both Fickian diffusion and protracted polymer structural relaxation. The incorporation of low levels of PEN into PET significantly reduces the excess free volume associated with the glassy state and, for these interval acetone sorption experiments in ∼ 5 μm-thick films, decreases the fraction of acetone uptake controlled by penetrant-induced polymer structural relaxation. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2973–2984, 1999     

The influence of vacuum-ultraviolet radiation on poly(ethylene terephthalate)

Poly(ethylene terephthalate) was exposed to radiation from different kinds of low-pressure plasmas in an oxygen atmosphere. The lower wavelength limit of the spectrum investigated, λ = 112 nm, is the cut-off of magnesium fluoride used for separating the specimen chamber from the plasma light source. The total surface oxygen concentration, and the formation of hydroxyl, carbonyl, and carboxyl groups were evaluated from XPS measurements in combination with chemical derivatizations, and their dependences on the radiation spectrum and the oxygen pressure in the sample chamber have been investigated. © 1996 John Wiley & Sons, Inc.     

Swelling-assisted modification of poly(ethylene terephthalate) by methacrylic acid

When a poly(ethylene terephthalate), PET, film is heated in an aqueous solution of methacrylic acid in the presence of hydrogen peroxide as an initiator, it is found that the weight of the film is increased. The amount of methacrylic acid that may be added onto the film is dependent upon the concentration of the monomer, the initiator, and the temperature at which the reaction occurs. Pretreatment of the film with 1,1,2,2,tetrachloroethane causes swelling and the amount of add-on is increased as the swelling level increases. Methacrylic-acid-modified PET films hydrolyze at room temperature in aqueous sodium hydroxide; the rate of hydrolysis is dependent upon the amount of add-on and the concentration of the base. This procedure leads to a chemically induced blend of polymethacrylic acid and poly(ethylene terephthalate), and grafting of the monomer onto the polymer film does not occur. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(ethylene glycol) methyl ether endcapped poly(ethylene terephthalate)

Linear and branched poly(ethylene terephthalate) (PET) copolymers with polyethylene glycol) (PEG) methyl ether (700 or 2000 g/mol) end groups were synthesized using conventional melt polymerization. DSC analysis demonstrated that low levels of PEG end groups accelerated PET crystallization. The incorporated PEG end groups also decreased the crystallization temperature of PET dramatically, and copolymers with a high content of PEG (>17.6 wt%) were able to crystallize at room temperature. Rheological analysis demonstrated that the presence of PEG end groups effectively decreased the melt viscosities and facilitated melt processing. XPS and ATR-FTIR revealed that the PEG end groups tended to aggregate on the surface, and the surface of compression molded films containing 34.0 wt% PEG were PEG rich (85 wt% PEG). PEG end-capped PET (34.0 wt% PEG) and PET films were immersed into a fibrinogen solution (0.7 mg/mL BSA) for 72 h to investigate the propensity for protein adhesion. XPS demonstrated that the concentration of nitrogen (1.05%) on the surface of PEG endcapped PET film was statistically lower than PET (7.67%). SEM analysis was consistent with XPS results, and revealed the presence of adsorbed protein on the surface of PET films.     

聚丙烯/聚对苯二甲酸乙二酯共混自增强材料的研究(Ⅰ)

本文根据聚丙烯（ＰＰ）与聚对苯二甲酸乙二醇酯（ＰＥＴ）共混对在熔 融状态下．流动粘度差阳溶度参数差大的特点，用挤出造粒的方法制得 共熔成纤目增强材料。通过扫描电镜观察．证实ＰＰ／ＰＥＴ比从９５／５到 ８０／２０时。ＰＥＴ均以纤维状结构分布在ＰＰ基质中。该共熔成纤体具有 良好的机械性能。在未加偶联剂时，拉伸强度虽略比纯ＰＰ低．但抗冲击 强度与纯ＰＰ相当。该结果可用于指导ＰＰ的改性和ＰＥＴ废料再生利用 工作。     

Organocatalytic depolymerization of poly(ethylene terephthalate)

We describe the organocatalytic depolymerization of poly(ethylene terephthalate) (PET), using a commercially available guanidine catalyst, 1,5,7‐triazabicyclo[4.4.0]dec‐5‐ene (TBD). Postconsumer PET beverage bottles were used and processed with 1.0 mol % (0.7 wt %) of TBD and excess amount of ethylene glycol (EG) at 190 °C for 3.5 hours under atmospheric pressure to give bis(2‐hydroxyethyl) terephthalate (BHET) in 78% isolated yield. The catalyst efficiency was comparable to other metal acetate/alkoxide catalysts that are commonly used for depolymerization of PET. The BHET content in the glycolysis product was subject to the reagent loading. This catalyst influenced the rate of the depolymerization as well as the effective process temperature. We also demonstrated the recycling of the catalyst and the excess EG for more than 5 cycles. Computational and experimental studies showed that both TBD and EG activate PET through hydrogen bond formation/activation to facilitate this reaction. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Remote nitrogen plasma treatment of polymers: Polyethylene,nylon 6,6, poly(ethylene vinyl alcohol), and poly(ethylene terephthalate)

A remote nitrogen plasma has been used for the rapid attachment of nitrogen to linear low density polyethylene, nylon 6,6, poly(ethylene vinyl alcohol), and poly(ethylene terephthalate). Analysis was performed using X-ray photoelectron spectroscopy to investigate the chemistry occurring on the surface. Nitrogen appeared to attach to the polymer chain at specific sites rather than uniformly over the whole chain as seen by the formation of high binding energy components and the continuously high intensity of the hydrocarbon component.