Characterization and comparison of poly(aryl ether ketone)s containing dibenzoylbiphenyl moieties: Effects of changes in biphenyl substitution pattern on thermal and mechanical properties

A monomer, 3,3′-bis (4-fluorobenzoyl) biphenyl, was prepared in high yield in two steps from inexpensive 3-chlorobenzoyl chloride and fluorobenzene, and polymerized by nucleophilic displacement reaction with various bisphenol monomers in tetramethylene sulfone to produce a series of high molecular weight poly(aryl ether ketone)s containing 3,3′-dibenzoylbiphenyl (DBBP) moieties. The spectroscopic, thermal, and thermomechanical properties of these polymers and related isomeric polymers having 2,2′-and 4,4′-DBBP units were determined and compared to study the effects of changes in the substitution pattern of the biphenyl unit. Except for the 2,2′-DBBP series of polymers, T_gs were found to increase with increasing linearity of the DBBP unit. The 2,2′-DBBP series of polymers had exceptionally high T_gs due to the sterically restricted motions in the biphenyl unit caused by the 2,2′-substitution. In addition, they also showed evidence for torsion with the 2,2′-DBBP unit, whereas in other isomeric polymers the DBBP units are believed to be relatively coplanar. Thermal stabilities and tensile moduli for these polymers proved to be independent of substitution patterns. © 1995 John Wiley & Sons, Inc.     

New poly (amide-imide) syntheses. IX. Preparation and properties of poly(amide-imide)s derived from 2,7-bis (4-aminophenoxy) naphthalene and various bis (trimellitimide)s

Eleven bis(phenoxy) naphthalene-containing poly(amide-imide)s IIIa–k were synthesized by the direct polycondensation of 2,7-bis (4-aminophenoxy) naphthalene (DAPON) with various aromatic bis (trimellitimide)s IIa–k in N-methyl-2-pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. Poly (amide-imide)s IIIa–k having inherent viscosities of 0.70–1.12 dL/g were obtained in quantitative yields. The polymers containing p-phenylene or bis(phenoxy) benzene units exhibited crystalline x-ray diffraction patterns. Most of the polymers were readily soluble in various solvents such as NMP, N, N-dimethylacetamide, dimethyl sulfoxide, m-cresol, o-chlorophenol, and pyridine, and gave transparent, and flexible films cast from DMAc solutions. Cast films showed obvious yield points in the stress-strain curves and had strength at break up to 87 MPa, elongation to break up to 11%, and initial modulus up to 2.10 GPa. These poly(amide-imide)s had glass transition temperatures in the range of 255–321°C, and the 10% weight loss temperatures were recorded in the range of 529–586°C in nitrogen. The properties of poly(amideimide)s IIIa–k were compared with those of the corresponding isomeric poly (amide-imide)s III′ prepared from 2,7-bis(4-trimellitimidophenoxy) naphthalene and aromatic diamines. © 1994 John Wiley & Sons, Inc.     

A novel synthesis of reactive polymers with pendant halomethyl groups by the polyaddition reaction of bis(epoxide)s with bis(chloroacetoxy)esters or bis(bromoacetoxy)esters

New reactive polymers with pendant halomethyl groups were successfully synthesized by polyaddition reactions of bis(epoxide)s with bis(chloroacetoxy)ester such as 1,4-bis [(chloroacetoxy)methyl]benzene (BCAMB) or 1,4-bis[(bromoacetoxy)methyl]benzene (BBAMB) using quaternary onium salts or crown ether complexes as catalysts. The polyaddition reaction of diglycidyl ether of bisphenol A (DGEBA) with BCAMB proceeded very smoothly with high yields (83–96%) by the addition of quaternary onium salts such as tetrabutylphosphonium bromide (TBPB) or crown ether complexes such as 18-crown-6/KBr as catalysts to produce high molecular weight polymers, although the reaction occurred without any catalyst to give low molecular weight polymer in low yield at 90°C for 48 h. It was also found that the reaction proceeded smoothly in aprotic polar solvents such as N-methyl-2-pyrrolidone (NMP) and N,N-dimethylacetamide (DMAc) to produce high molecular weight polymers. Polyaddition reactions of DGEBA or digylcidyl ether of ethylene glycol (DGEEG) with BBAMB, other bis(chloroacetoxy)esters or bis(bromoacetoxy)esters using TBPB in DMAc also proceeded smoothly to give the corresponding polymers. The resulting poly(ether-ester)s contain reactive halomethyl groups as side chains, which were introduced during main chain formation. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3791–3799, 1997     

Synthesis and characterization of fluoropolymers by the polyaddition of bis(epoxide)s with dicarboxylic acids and diols

The synthesis and characterization of the fluoropolymers poly 1a – 1d and poly 2a – 2d with pendant hydroxyl groups were examined. The polyaddition of bis(epoxide)s [2,2′‐bis(4‐glycidyletherphenyl)hexafluoropropane and bisphenol A diglycidyl ether] with dicarboxylic acids (tetrafluoroterephthalic acid and terephthalic acid) and diols [2,2′‐bis(4‐hydroxyphenyl)hexafluoropropane, 2,2′,3,3′,5,5′,6,6′‐octafluoro‐4,4′‐biphenol, 1,4‐bis(hexafluorohydroxyisopropyl)benzene, and 1,3‐bis(hexafluorohydroxyisopropyl)benzene] was carried out at 50–100 °C for 6–48 h in the presence of quaternary onium salts (tetrabutylammonium bromide, tetrabutylammonium chloride, tetrabutylphosphonium bromide, and tetrabutylphosphonium chloride; 2.5 mol %) as catalysts in dimethyl sulfoxide, N‐methylpyrrolidone, dimethylformamide, dimethylacetamide, dioxane, diglyme, o‐dichlorobenzene, chlorobenzene, and toluene to afford the corresponding polymers, poly 1a – 1d and poly 2a – 2d , with number‐average molecular weights of 11,000–59,400 in 45–97% yields. The solubility of the obtained polymers was good, and their thermal stability might be assumed from their structures. A linear relationship was observed between the contents of the fluorine atoms and the refractive indices. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1395–1404, 2002     

New poly(amide-lmide)s syntheses. XV. Preparation and properties of poly(amide-imide)s derived from 9, 9-bis[4-(4-aminophenoxy) phenyl]fluorene and various bis(trimellitimide)s

Fifteen bis(phenoxy) fluorene-containing poly(amide-imide)s III were synthesized by the direct polycondensation of 9,9-bis[4-(4-aminophenoxy)phenyl]fluorene (BAPPF) with var-ious aromatic bis(trimellitimide)s II in N-methyl-2-pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. Poly(amide-imide)s III having inherent vis-cosities up to 1.45 dL/g were obtained in quantitative yields. Most of the resulting polymers showed an amorphous nature and were readily soluble in polar solvents such as NMP and N,N-dimethylacetamide. All the soluble poly(amide-imide)s afforded transparent, flexible, and tough films. The glass transition temperatures of these polymers were in the range of 263–315°C and the 10% weight loss temperatures were above 510°C in nitrogen. Some properties of poly(amide-imide)s III were compared with those of the corresponding isomeric poly(amide-imide)s III ′ prepared from 9,9-[4-(4-trimellitimidophenoxy)phenyl]fluorene and various aromatic diamines. © 1995 John Wiley & Sons, Inc.     

Synthesis and Characterization of Poly(Aryl Ether-Bissulfone)s

A series of poly(aryl ether-bissulfone)s were synthesized from bis-phenols, 4,4′-bis(4-chlorophenylsulfonyl)biphenyl, and 4,4′-bis(4-fluorophenylsulfonyl)biphenyl. The bishalide monomers were synthesized by reaction of 4,4′-bis(chlorosulfonyl)biphenyl with a suitable aryl halide. Potassium carbonate mediated reaction in di-methylacetamide gave high molecular weight polymers in excellent yield. The polymers are soluble in dipolar aprotic solvents. Unlike the corresponding monosulfone analogues, the poly(aryl ether-bissulfone)s exhibited poor solubility in chlorinated hydrocarbons. The glass transition temperatures of the polymers are among the highest known for poly(aryl ether)s (241-271 °C). In addition, the polymers exhibit excellent thermal stability and they produce clear, colorless tough films by solution casting or compression molding.     

New poly(amide-imide)s syntheses. XVII. Preparation and properties of poly(amide-imide)s derived from 3,3-Bis[4-(4-aminophenoxy)phenyl]phthalimidine and various bis(trimellitimide)s

A series of novel bis(phenoxy)phthalimidine-containing poly(amide-imide)s III were synthesized by the direct polycondensation of 3,3-bis[4-(4-aminophenoxy)phenyl]phthalimidine (BAPP) with various aromatic bis(trimellitimide)s in N-methyl-2-pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. Poly(amide-imide)s III , having inherent viscosities up to 1.36 dL/g, were obtained in quantitative yields. All resulting polymers showed an amorphous nature and were readily soluble in polar solvents such as NMP and N,N-dimethylacetamide. All the soluble poly(amide-imide)s afforded transparent, flexible, and tough films. The glass transition temperatures of these polymers were in the range of 267–322°C and the 10% weight loss temperatures were above 490°C in nitrogen. Some properties of poly(amide-imide)s III were compared with those of the corresponding isomeric poly(amide-imide)s III′ prepared from 3,3-[4-(4-trimellitimidophenoxy)phenyl]-phthalimidine and various aromatic diamines. © 1996 John Wiley & Sons, Inc.     

Synthesis and Properties of Novel Poly（amine ether）s

Using aromatic bis（4-bromophenyl） ether and various aromatic diamines as the monomers, a series of novel poly（amine ether）s （PAEs） have been synthesized via palladium-catalyzed aryl amination, which is the Hartwig-Buchwald polycondensation reaction. Their structures were characterized by means of elemental analysis, FT-IR, 1^H NMR and UV-Vis spectroscopy. The results show a good agreement with the proposed structures. Their general properties were studied by DSC and TG and it＇s obvious that they show high glass transition temperatures （Tg〉200 ℃）, good thermal stability with high decomposition temperatures （TD〉500℃） and excellent solubility. The mechanical behavior of these polymers suggested that they could be considered a new class of high-performance polymers.     

Synthesis,characterization, and comparison of properties of new fluorinated poly(arylene ether)s containing phthalimidine moiety in the main chain

Four new poly(arylene ether)s have been prepared by the reaction of N‐phenyl‐3,3‐bis(4‐hydroxyphenyl)phthalimidine (PA) with four different perfluoroalkylated monomers namely 1,3‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) benzene, 4,4′‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) biphenyl, 2,6‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) pyridine, and 2,5‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) thiophene. The poly(arylene ether)s were characterized by different spectroscopic, thermal, mechanical, and electrical techniques. The poly(arylene ether) containing quadriphenyl unit in the main chain showed very high glass transition temperature of 291°C and outstanding thermal stability upto 556°C for 10% weight loss under a 4:1 nitrogen:oxygen mixture. The polymers were soluble in a wide range of organic solvents. Transparent thin films of these polymers exhibited tensile strengths upto 75 MPa and elongation at break upto 32%. The films of these polymers showed low water absorption of 0.26%. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and characterization of new highly organosoluble poly(ether imide)s based on 3,3′,5,5′‐tetramethyl‐2,2‐bis[4‐(4‐dicarboxyphenoxy)phenyl]propane dianhydride

A new bis(ether anhydride), 3,3′,5,5′‐tetramethyl‐2,2‐bis[4‐(4‐dicarboxyphenoxy)phenyl]propane dianhydride ( 3 ), was prepared in three steps: the nitro displacement of 4‐nitrophthalonitrile with 2,2‐bis(4‐hydroxy‐3,5‐dimethylphenyl)propane, the alkaline hydrolysis of the intermediate bis(ether dinitrile), and the subsequent dehydration of the resulting bis(ether diacid). A series of new highly soluble poly(ether imide)s with tetramethyl and isopropylidene groups were prepared from the bis(ether anhydride) 3 with various diamines by a conventional two‐stage synthesis including polyaddition and chemical cyclodehydration. The resulting poly(ether imide)s had inherent viscosities of 0.54–0.73 dL g^?1. Gel permeation chromatography measurements revealed that the polymers had number‐average and weight‐average molecular weights of up to 54,000 and 124,000, respectively. All the polymers showed typical amorphous diffraction patterns. All of the poly(ether imide)s showed excellent solubility and were readily dissolved in various solvents such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, N,N‐dimethylformamide, pyridine, cyclohexanone, tetrahydrofuran, and even chloroform. Most of the polymers could be dissolved with chloroform concentrations as high as 30 wt %. These polymers had glass‐transition temperatures of 244–282 °C. Thermogravimetric analysis showed that all polymers were stable, with 10% weight losses recorded above 463 °C in nitrogen. These transparent, tough, and flexible polymer films were obtained through solution casting from N,N‐dimethylacetamide solutions. These polymer films had tensile strengths of 81–102 MPa and tensile moduli of 1.8–2.0 GPa. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2556–2563, 2002     

Synthesis and Characterization of Novel Organosoluble Methyl Substituted Poly(aryl Ether Ketone)s Containing Sulfone Linkage

Several new methyl substituted poly(aryl ether ketone)s containing sulfone linkage with inherent viscosities of 0.62–0.84 dL/g have been prepared from 4,4′‐bis(2‐methylphenoxy)diphenylsulfone and 4,4′‐bis(3‐methylphenoxy)diphenylsulfone with terephthaloyl chloride and isophthaloyl chloride by electrophilic Friedel‐Crafts acylation in the presence of DMF with anhydrous AlCl₃ as a catalyst in 1,2‐dichloroethane, respectively. These polymers having weight‐average molecular weight in the range of 71,000–49,000 are all amorphous and show high glass transition temperatures ranging from 167 °C to 191 °C, excellent thermal stability at temperatures over 400 °C in air or nitrogen, high char yields of 51–58% in nitrogen and good solubility in CHCl₃ and polar solvents such as DMF, DMSO and NMP at room temperature.     

A novel synthesis of polyethers with pendant hydroxyl groups by polyaddition of bis(oxetane)s with bis(phenol)s

The polyaddition of 1,4-bis[(3-ethyl-3-oxetanyl)methoxymethyl]benzene (BEOB) with 3,3′,5,5′-tetrachlorobisphenol A (TCBPA) was examined with or without catalysts. High molecular weight polymer (polymers 1) (M_n = 13,600) with pendant primary hydroxyl groups was obtained in a 99% yield without any gel products when the reaction was performed with 5 mol % of tetraphenylphosphonium bromide as a catalyst in NMP at 160°C for 96 h. However, when the reaction was carried out without a catalyst under the same conditions, a low molecular weight polymer (M_n = 3200) was obtained in a 51% yield. The structure of the resulting polymer was confirmed by IR, ¹H-NMR, and ¹³C-NMR spectra. In this reaction system, it was also found that tetraphenylphosphonium iodide and crown ether complexes such as 18-crown-6 (18-C-6)/KBr and 18-C-6/KI have high catalytic activity. Polyadditions of 1,4-bis[(3-methyl-3-oxetanyl)methoxymethyl]benzene with TCBPA and BEOB with 3,3′,5,5′-tetrabromobisphenol-S were also examined, and corresponding polymers (polymers 2 and 3) were obtained in good yields. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2781–2790, 1999     

Poly(1,3,4-oxadiazole-ether-imide)s and their polydimethylsiloxane-containing copolymers

Poly(1,3,4-oxadiazole-ether-imide)s were prepared by thermal imidization of poly(amic-acid) intermediates resulting from the solution polycondensation reaction of a bis(ether-anhydride), namely 2,2′-bis-[(3,4-dicarboxyphenoxy)phenyl]-1,4-phenylenediisopropylidene dianhydride, with different aromatic diamines containing 1,3,4-oxadiazole ring, such as 2,5-bis(p-aminophenyl)-1,3,4-oxadiazole, 2,5-bis[p-(4-aminophenoxy)phenyl]-1,3,4-oxadiazole, 2-(4-dimethylaminophenyl)-5-(3,5-diaminophenyl)-1,3,4-oxadiazole. Poly(1,3,4-oxadiazole-ether-imide)-polydimethylsiloxane copolymers were prepared by polycondensation reaction of the same bis(ether-anhydride) with equimolar quantities of an aromatic diamine having 1,3,4-oxadiazole ring and a bis(aminopropyl)polydimethylsiloxane oligomer of controlled molecular weight. A solution imidization procedure was used to convert quantitatively the poly(amic-acid) intermediates to the corresponding polyimides. All the polymers were easily soluble in polar organic solvents such as N-methylpyrrolidone and N,N-dimethylacetamide. The polymers showed good thermal stability with decomposition temperature being above 400 °C. Solutions of some polymers in N-methylpyrrolidone exhibited blue fluorescence, having maximum emission wavelength in the range of 370-412 nm.     

Synthesis and properties of poly[arylene ether (N-arylenebenzimidazole)]s

Poly(arylene ether)s containing N-arylenebenzimidazole groups were prepared by the aromatic nucleophilic displacement reaction of two new bis(hydroxyphenyl-N-arylenebenzimidazole)s with activated aromatic difluorides in sulfolane at 200°C in the presence of anhydrous potassium carbonate. The bis(hydroxyphenyl-N-arylenebenzimidazole)s were prepared from bis(o-aminoanilino) arylenes and phenyl-4-hydroxybenzoate. The polymers were soluble in N-methyl-2-pyrrolidinone and m-cresol and exhibited inherent viscosities from 0.37–0.86 dL/g and glass transition temperatures from 219–289°C. Thermogravimetric analyses showed 5% weight losses from 463–506°C in air and 467–522°C in nitrogen. Unoriented thin films exhibited tensile strengths, moduli, and break elongations at 23°C of 10.2–12.5 ksi, 318–365 ksi, and 4–7%, respectively, and at 177°C of 5.1–6.9 ksi, 256–296 ksi, and 1–5%, respectively. A 50 : 50 random copolymer prepared from 1,3-bis(4-fluorobenzoyl) benzene, 1,1'-(4,4'-biphenylene)-bis[2-(4-hydroxyphenyl)benzimidazole], and 5,5'-bis[2-(4-hydroxyphenyl)benzimidazole] exhibited higher moisture absorption and lower tensile properties than those predicted by a rule of mixtures relationship. The chemical, physical, and mechanical properties of these polymers are discussed. © 1993 John Wiley & Sons, Inc.?     

Synthesis and properties of poly(amide-imide)s based on the diimide-diacid condensed from 2,2′- bis(4-aminophenoxy)biphenyl and trimellitic anhydride

A new dicarboxylic acid having a kinked structure was synthesized from the condensation of 2,2′-bis(4-aminophenoxy)biphenyl and trimellitic anhydride. A series of biphenyl-2,2′-diyl-containing aromatic poly(amide-imide)s having inherent viscosities of 0.23–0.94 dL/g was prepared by the triphenyl phosphite activated polycondensation from the diimide-diacid II with various aromatic diamines in a medium consisting of N-methyl-2-pyrrolidone (NMP), pyridine, and calcium chloride. Most of the resulting polymers showed an amorphous nature and were readily soluble in a variety of organic solvents including NMP and N,N-dimethylacetamide (DMAc). Transparent, flexible, and tough films of these polymers could be cast from DMAc or NMP solutions. The glass transition temperatures of these polymers were in the range of 227–261°C and the 10% weight loss temperatures were above 520°C in nitrogen. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1169–1177, 1998     

Photopolyaddition of dithiols to bis(alkoxyallene)s

Polyadditions of 1,4-benzenedithiol (BDT) to bis(alkoxyallene)s, such as 1,4-bis(allenyloxy)xylene (3) and 1,4-bis(allenyloxy) benzene (4) , were carried out in benzene at 25°C by irradiation with a high pressure mercury lamp. Thiol groups were added to the terminal double bonds of the allenyloxy groups selectively to afford polymers containing reactive carbon–carbon double bonds in the main chain, similar to the radical polyadditions using azobis(isobutyronitrile) (AIBN). The molecular weight of the polymer obtained from BDT and 3 was 10 times higher than that of the polymer produced in the radical polyaddition with AIBN; whereas the molecular weight of the polymer from BDT and 4 was similar to that in the radical polyaddition, probably because of poor solubility of 4 and the polymer toward benzene. The geometrical structure of carbon–carbon double bonds in the polymer isomerized from an E to Z structure with reaction time by virtue of both the addition elimination of thiyl radical to the double bonds and the UV irradiation. © 1996 John Wiley & Sons, Inc.     

双邻位甲基取代的聚芳醚酮合成与表征

两种单体 2 ,2′ ,6 ,6′ 四甲基 4 ,4′ 二苯氧基二苯酮 (o M2 DPOBP)和 2 ,2′ ,6 ,6′ 四甲基 4 ,4′ 二苯氧基三苯二酮 (o M2 DPOTPDK) ,分别与对苯二甲酰氯 (TPC)和间苯二甲酰氯 (IPC)低温亲电溶液缩聚 ,合成了 4种含双邻位甲基侧基聚醚酮醚酮酮 (DM PEKEKK和DM PEKEKMK)及含双邻位甲基侧基聚醚酮酮醚酮酮 (DM PEKKEKK和DM PEKKEKMK)聚合物 .用FT IR、1 H NMR、DSC、TGA、WAXD等方法对聚合物进行了表征 ,研究了聚合物的溶解性能 .结果表明 ,该 4种聚合物具有较高的玻璃化转变温度 ,良好的热稳定性和优良的溶解性能 .     

Copolymerization of bis(2-oxazoline)s,anhydrides, and diols or diamines. Reaction mechanisms and polymer properties

The preparation of linear poly(ester-amide)s from monoanhydrides, bis(2-oxazoline)s (namely 2,2′-(1,4-phenylene)bis(2-oxazoline)) and a third comonomer is discussed. The polymerization reactions were carried out in bulk between 150 and 200°C. When the third monomer is a diol, poly(ester-ester-amide)s are obtained. Diols of different structure were used: α,ω-diols having up to 12 carbon atoms, ethylene glycol oligomers (two or three repeating units), cyclic diols, etc.; glutaric, 3,3-dimethylglutaric and maleic anhydrides were used as monoanhydrides. The polymers were studied from the point of view of thermal properties, finding a substantial agreement between the structure of the monomers and the glass transition temperature of the polymers. By using primary diamines as a third comonomer, the reaction does not lead to the formation of a polymeric product. The failure of the polymerization was attributed to a competitive reaction that prevents the polymerization. After the amine group has reacted with the anhydride, cyclization of the so-formed carboxyalkylamide occurs, giving an imide derivative, unable to react further. Therefore, only a mixture of low molecular weight compounds is obtained in this case. When the diamine is secondary, the imidization reaction is not possible, and linear poly(amide-ester-amide)s are obtained. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3241–3248, 1997     

Synthesis and properties of poly(ether imide)s based on the bis(ether anhydride)s from hydroquinone and its derivatives

Four bis(ether anhydride)s, 4,4′‐(1,4‐phenylenedioxy)diphthalic anhydride (IV), 4,4′‐(2,5‐tolylenedioxy)‐diphthalic anhydride (Me‐IV), 4,4′‐(2‐chloro‐1,4‐phenylenedioxy)diphthalic anhydride (Cl‐IV), and 4,4′‐(2,5‐biphenylenedioxy)diphthalic anhydride (Ph‐IV), were prepared in three steps starting from the nucleophilic nitrodisplacement reaction of 4‐nitrophthalonitrile with the potassium phenoxides of hydroquinone and various substituted hydroquinones such as methylhydroquinone, chlorohydroquinone, and phenylhydroquinone in N,N‐dimethylformamide, followed by alkaline hydrolysis and dehydration. Four series of poly(ether imide)s were prepared from bis(ether anhydride)s with various aromatic diamines by a classical two‐step procedure. The inherent viscosities of the intermediate poly(amic acid)s were in the range of 0.40–2.63 dL/g. Except for those derived from p‐phenylenediamine and benzidine, almost all the poly(amic acid)s could be solution‐cast and thermally converted into transparent, flexible, and tough polyimide films. Introduction of the chloro or phenyl substituent leads to a decreased crystallinity and an increased solubility of the polymers. The glass transition temperatures (T_g) of these polyimides were recorded in the range of 204–263°C. In general, the methyl‐ and chloro‐substituted polyimides exhibited relatively higher T_gs, whereas the phenyl‐substituted ones exhibited slightly lower T_gs compared to the corresponding nonsubstituted ones. Thermogravimetric analysis (TG) showed that 10% weight loss temperatures of all the polymers were above 500°C either in nitrogen or in air. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 665–675, 1999     

Poly(Aryl Ether)s from a Novel Biphenol Monomer Containing a Dicyanoarylene Group

Abstract

The preparation of a novel biphenol, 1,4-bis(4-hydroxyphenyl)-2,3-dicyanonaphthalene, from phenolphthalein is described. This biphenol was prepared in high yield in a four-step reaction sequence. The biphenol can be polymerized with activated dihalides such as 1,2-bis-(4-fluorobenzoyl)-3,4,5,6-tetraphenylbenzene, bis(4-fluorophenyl) sulfone, and 4,4′-dichlorobenzophenone to give high molecular weight amorphous poly(aryl ether)s. The polymers have glass transition temperatures ranging from 284 to 319°C and are easily cast into flexible, colorless, and transparent films. The 5% weight loss temperatures of these polymers, by thermogravimetric analysis in air and nitrogen, are all above 500°C.