Effect of solvents on properties of polymer gel-electrolyte based on polyester diacrylate

New polymer gel electrolytes based on polyester diacrylates and LiClO₄ salt solutions in organic solvents are developed for lithium ion and lithium polymer batteries with a high ionic conductivity up to 2.7 × 10^?3 Ohm^?1cm^?1 at the room temperature. To choose the optimum liquid electrolyte composition, the dependence is studied of physico-chemical parameters of new gel electrolytes on the composition of the mixture of aprotic organic solvents: ethylene carbonate, propylene carbonate, and λ-butyrolacton. The bulk conductivity of gel electrolytes and exchange currents at the gel electrolyte/Li interface are studied using the electrochemical impedance method in symmetrical cells with two Li electrodes. The glass transition temperature and gel homogeneity are determined using the method of differential scanning calorimetry. It is found that the optimum mixture is that of propylene carbonate and λ-butyrolacton, in which a homogeneous polymer gel is formed in a wide temperature range of ?150 to +50°C.     

New solid polymer electrolytes based on polyester diacrylate for lithium power sources

New solid polymer electrolytes are developed for a lithium power source used at the temperatures up to 100°C. Polyester diacrylate (PEDA) based on oligohydroxyethylacrylate and its block copolymers with polyethylene glycol were offered for polymer matrix formation. The salt used was LiClO₄. The ionic conductivity of electrolytes was measured in the range of 20 to 100°C using the electrochemical impedance method. It is shown that the maximum conductivity in the whole temperature range is characteristic of the electrolyte based on the PEDA copolymer and polyethylene glycol condensation product (2.8 × 10^?6 S cm^?1 at 20°C, 1.8 × 10^?4 S cm^?1 at 95°C).     

Ionic conductivity probed in main chain liquid crystalline azobenzene polyesters

Three main chain thermotropic liquid crystalline (LC) azobenzene polymers were synthesized using the azobenzene twin molecule (P4P) having the structure Phenylazobenzene‐tetraethyleneglycol‐Phenylazobenzene as the AA monomer and diols like diethylene glycol, tetraethylene glycol (TEG), and hexaethylene glycol as the BB comonomer. Terminal ? C(O)OMe units on P4P facilitated transesterification with diols to form polyesters. All polymers exhibited stable smectic mesophases. One of the polymers, Poly(P4PTEG) was chosen to prepare composite polymer electrolytes with LiCF₃SO₃ and ionic conductivity was measured by ac impedance spectroscopy. The polymer/0.3 Li salt complex exhibited a maximum ionic conductivity in the range of 10^?5 S cm^?1 at room temperature (25 °C), which increased to 10^?4 S cm^?1 above 65 °C. The temperature dependence of ionic conductivity was compared with the phase transitions occurring in the sample and it was observed that the glass transition had a higher influence on the ionic conductivity compared to the ordered LC phase. Reversible ionic conductivity switching was observed upon irradiation of the polymer/0.3 Li salt complex with alternate UV and visible irradiation. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 629–641     

Synthesis and properties of all solid polymer electrolytes based on poly(vinyl acetate‐co‐acetyl ethylene oxide acrylate)

Poly(acetyl ethylene oxide acrylate‐co‐vinyl acetate) (P(AEOA‐VAc)) was synthesized and used as a host for lithium perchlorate to prepare an all solid polymer electrolyte. Introduction of carbonyl groups into the copolymer increased ionic conductivity. All solid polymer electrolytes based on P(AEOA‐VAc) at 14.3 wt% VAc with 12wt% LiClO₄ showed conductivity as high as 1.2 × 10^?4 S cm^?1 at room temperature. The temperature dependence of the ionic conductivity followed the VTF behavior, indicating that the ion transport was related to segmental movement of the polymer. FTIR was used to investigate the effect of the carbonyl group on ionic conductivity. The interaction between the lithium salt and carbonyl groups accelerated the dissociation of the lithium salt and thus resulted in a maximum ionic conductivity at a salt concentration higher than pure PAEO‐salts system. Copyright © 2010 John Wiley & Sons, Ltd.     

Polymer solid electrolytes from the PEG-PMMA-LiCF3SO3 system

Highly conductive solid polymeric electrolytes based upon low molecular weight poly(ethylene glycol) and ethylene oxide/propylene oxide copolymers blended with up to 50% by volume of poly(methyl methacrylate) have been synthesized using LiCF₃SO₃ (25:1 ether oxygen to cation ratio). Room-temperature ionic conductivities were measured to be in the range 10^?4 to 10^?5 S/cm for poly(methyl methacrylate) concentrations up to 30% by volume. In some cases, the addition of the poly(methyl methacrylate) enhanced the conductivity. All of the electrolytes studied were either amorphous or crystallized below 0°C. The variation of conductivity with temperature and polymer composition was measured and the results were analyzed in terms of effective medium theory and semiempirical considerations. Ionic transport is coupled to the structural relaxation of the polymer segments. At lower temperatures activated processes were required. Both charge carrier mobility and charge concentration were found to contribute to conduction. The effective medium theory quantitatively describes conductivities of amorphous heterogenous systems of limited miscibility (microphase separation) quite well. For miscible or partially crystalline systems other effects not incorporated in this theory play an important role, and conductivities are measured to be higher than theoretically predicted. © 1994 John Wiley & Sons, Inc.     

ETHYLENE OXIDE-ETHYLENE TEREPHTHALATE SEGMENTED COPOLYMER SOLID ELECTROLYTE8

 A series of ethylene oxide-ethylene terephthalate segmented copolymers (EOET) weresynthesized and complexed with LiClO₄ to form some new polymer electrolytes. The EOET-LiClO₄ electrolytes exhibit not only high ionic conductivity, but also good mechanical strengthand toughness. The EOET 3400--25--LiClO₄ complex possesses the highest conductivity (4. 65×10^-5s·cm^-1 at room temperature when the ratio [Li⁺]/[EO] equals 1/16. The structures of these electrolytes were examined with FTIR analysis, X-ray diffraction and DSC thermograms,and the results of high ionic conductivity of the segmented copolymers were discussed.     

Synthesis of networked polymers by copolymerization of monoepoxy‐substituted lithium sulfonylimide and diepoxy‐substituted poly(ethylene glycol), and their properties

Networked polymers that had poly(ethylene glycol) (PEG) chains and lithium sulfonylimide salt structures were prepared by curing a mixture of poly(ethylene glycol) diglycidyl ether and lithium 3‐glycidyloxypropanesulfonyl‐trifluoromethanesulfonylimide with poly(ethylene glycol) bis(3‐aminopropyl) terminated. The obtained flexible self‐standing networked polymer films showed high thermal and mechanical stability with relatively high ionic conductivity. The room temperature ionic conductivity under a dry condition was in the range of 10^?5 ～ 10^?4 S m^?1, which is one order of magnitude higher than the corresponding networked polymers having lithium sulfonate salt structures (10^?6 ～ 10^?5 S m^?1). The film sample became swollen by immersing in propylene carbonate (PC) or PC solution of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). The sample swollen in PC showed higher ionic conductivity (7.2 × 10^?3 S m^?1 at room temperature), and the sample swollen in 1.0 M LiTFSI/PC showed much higher ionic conductivity (8.2 × 10^?1 S m^?1 at room temperature). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Electrical Characterization and Ionic Transport Properties of Carboxyl Methylcellulose-Oleic Acid Solid Polymer Electrolytes

Electrical impedance spectroscopy was used to measure the conductivity of solid polymer electrolytes. From the impedance study, the highest ionic conductivity of solid polymer electrolytes based on carboxyl methylcellulose as polymer host and oleic acid as the doping salt, prepared by the solution casting method at room temperature, σ_r.t, is 2.11 × 10^?5 S cm^?1 for the sample containing 20 wt.% of oleic acid. Transference number measurement was performed to correlate the diffusion phenomena to the conductivity behavior of carboxyl methylcellulose-oleic acid solid polymer electrolytes. From the transference number measurement study, the conduction species carrier of the cation (+) is higher than that of the anion (?). Thus, the results proved that the samples are proton-conducting solid polymer electrolytes.     

Novel composite polymer electrolytes based on poly(ether-urethane) network polymer and fumed silicas

Novel composite solid polymer electrolytes (CSPEs) and composite gel polymer electrolytes (CGPEs) have been prepared. CSPE consists of poly(ether-urethane) network polymer (PUN), fumed silicas and LiClO₄. The ionic conductivity of CSPEs can be enhanced nearly 20 times in comparison with the plain system without the addition of fumed silicas and can be above 1×10⁻⁵ S/cm at room temperature. The effects of both kinds of fumed silicas, viz. uSiO₂ with hydrophilic groups at the surface and mSiO₂ with hydrophobic groups at the surface on ionic conductivity were investigated. CGPE comprising of the CSPE and LiClO₄–PC solution with good mechanical strength exhibits ionic conductivity in the order of 10⁻³ S/cm at room temperature and above 3×10⁻⁴ S/cm at low temperature −40 °C.     

Synthesis and properties of polymeric analogs of ionic liquids

A number of methacrylate ionic monomers with different structures and mobilities of ionic centers were synthesized. The free-radical polymerization of these monomers in solution affords high-molecular-mass (M _sD = 0.5 to 2.5 × 10⁶) thermally stable (T _dec > 170°C) polyelectrolytes or cationic or anionic “polymeric ionic liquids.” The conductivities of polycation- and polyanion-derived coatings are (7.4 × 10^?10)?(7.6 × 10^?7) and (4.9 × 10^?10)-(1.6 × 10^?7) S/cm (25°C), respectively. As exemplified by poly(1-[3-(methacryloyloxy)propyl]-3-methylimidazolium bis[(trifluoromethanesulfonyl)imide]), the molecular mass and glasstransition temperature of the polymer affect the ionic conductivity of the film coating. The transition from linear polyelectrolytes to crosslinked systems based on ionic monomers and poly(ethylene glycol dimethacrylate) 750 leads to the formation of elastic films featuring satisfactory strength, reduced glass-transition temperatures (?8 to +15°C), and increased ionic conductivity (up to 3.2 × 10^?6 S/cm (25°C)).     

Solid polymer electrolytes based on crosslinkable polyoctahedral silsesquioxanes (POSS) for room temperature lithium polymer batteries

Solid polymer electrolytes (SPE), based on polyoctahedral silsesquioxanes (POSS) as a crosslinking agent, were prepared by radical polymerization. The ionic conductivity is greatly enhanced by introduction of crosslinkable POSS with multifunctional groups. The SPE prepared with 5 wt.% crosslinking agent shows an ionic conductivity of 5.3?×?10^?4 S cm^?1 at room temperature. The content of nonvolatile plasticizer, poly(ethylene glycol) dimethyl ether, in the SPE, could be raised to 95 wt.% without any leakage. The SPE is found to be electrochemically stable up to 5.3 V. Lithium polymer cell consisting of Li/SPE/LiCoO₂ exhibits 80% of initial discharge capacity even at the rate of 0.1 C at room temperature after 20 cycles, which is a substantial improvement for practical consideration of lithium polymer batteries at room temperature.     

Polymer electrolyte membranes by in situ polymerization of poly(ethylene carbonate‐co‐ethylene oxide) macromonomers in blends with poly(vinylidene fluoride‐co‐hexafluoropropylene)

Salt‐containing membranes based on polymethacrylates having poly(ethylene carbonate‐co‐ethylene oxide) side chains, as well as their blends with poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP), have been studied. Self‐supportive ion conductive membranes were prepared by casting films of methacrylate functional poly(ethylene carbonate‐co‐ethylene oxide) macromonomers containing lithium bis(trifluorosulfonyl)imide (LiTFSI) salt, followed by irradiation with UV‐light to polymerize the methacrylate units in situ. Homogenous electrolyte membranes based on the polymerized macromonomers showed a conductivity of 6.3 × 10^?6 S cm^?1 at 20 °C. The preparation of polymer blends, by the addition of PVDF‐HFP to the electrolytes, was found to greatly improve the mechanical properties. However, the addition led to an increase of the glass transition temperature (T_g) of the ion conductive phase by ～5 °C. The conductivity of the blend membranes was thus lower in relation to the corresponding homogeneous polymer electrolytes, and 2.5 × 10^?6 S cm^?1 was recorded for a membrane containing 10 wt % PVDF‐HFP at 20 °C. Increasing the salt concentration in the blend membranes was found to increase the T_g of the ion conductive component and decrease the propensity for the crystallization of the PVDF‐HFP component. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 79–90, 2007     

A new composite polymer electrolyte based on poly(ethyleneoxide)/ polysiloxane/BMImTFSI/organomontmorillonite

Composite polymer electrolytes based on poly(ethylene oxide)-polysiloxane/l-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide/organomontmorillonite(PEO-PDMS/1L/OMMT) were prepared and characterized.Addition of both an ionic liquid and OMMT to the polymer base of PEO-PDMS resulted in an increase in ionic conductivity.At room temperature,the ionic conductivity of sample PPB100-OMMT4 was 2.19×10~3 S/cm.The composite polymer electrolyte also exhibited high thermal and electrochemical stability and may potentially be applied in lithium batteries.     

Synthesis and characterization of poly(ethylene glycol amine) electrolytes and nanocomposites based on graphite

Poly(ethylene glycol) functionalized with an amino group (PEG-amine) was synthesized and characterized by proton NMR and FTIR spectroscopy. The polymer was complexed with lithium triflate (LiOTf) in varying ratios, and it was found that the composition (PEG-amine)_8.0LiOTf exhibited a maximum ionic conductivity of 10^?5 S/cm at a temperature of 320 K. Graphite platelets were also dispersed into the polymer matrix, and the resulting nanomaterials were shown to be electrically conductive, with a maximum value of 1 × 10³ S/cm when the graphite is present at 50% by mass.     

Magnesium ion transport in poly(ethylene oxide)-based polymer electrolyte containing plastic-crystalline succinonitrile

A new composition of magnesium (Mg)-ion-conducting polymer electrolyte comprising poly(ethylene oxide) (PEO) complexed with Mg trifluoromethanesulfonate (Mg triflate or Mg(Tf)₂) containing different amounts of a nonionic plastic crystal succinonitrile (SN) has been prepared and characterized. High polarity and rotational disorder of the SN molecules in the plastic-crystalline phase, supports the enhancement of ionic conductivity of the PEO-Mg(Tf)₂ complex system, showing a maximum room temperature ionic conductivity of ～6?×?10^-4 S cm^?1 observed with the addition of 50 wt.% of SN. X-ray diffraction, optical microscopy, and differential scanning calorimetry suggest a substantial structural modification, decrease in crystallinity, and various interactions in the polymer electrolyte components due to addition of SN. The cyclic voltammetry, impedance, and dc polarization studies confirm the Mg-ion conduction in the PEO complex. The electrochemical potential window of the electrolyte, observed from the linear sweep voltammetry, is determined to be ～4.1 V. The performance characteristics of the SN-incorporated polymer electrolyte system indicate their potential applicability as electrolytes in ionic devices including Mg batteries.     

Proton-conducting membranes: poly (N-vinyl pyrrolidone) complexes with various ammonium salts

The present study focuses on the proton-conducting polymer electrolytes; poly (N-vinyl pyrrolidone)–ammonium thiocyanate and poly (N-vinyl pyrrolidone)–ammonium acetate prepared by solution casting technique. The XRD analysis indicates the amorphous nature of the polymer electrolytes. The Raman spectra of the C=O vibration of pure polymer PVP at 1,663 cm^?1 has been appeared as doublet in the polymer electrolytes. The introduction of this new peak in the salt-doped polymer electrolytes may be due to interaction of the cation with the polymer. The room temperature ionic conductivity σ _303κ has been found to be high, 1.7?×?10^?4 S cm^?1 for 80 mol% PVP–20 mol% NH₄SCN and 1.5?×?10^?6 S cm^?1 for 75 mol% PVP–25 mol% CH₃COONH₄. The polymer electrolytes have been tested for their application in Zn–air battery.     

Studies on poly(vinyl pyrrolidone) based solid polymer blend electrolytes complexed with various lithium salts

Solid polymer electrolytes (SPEs) with high ionic conductivity and acceptable mechanical properties are of particular interest for increasing the performance of batteries. In the present work, SPEs based on poly(ethylene oxide)/poly (vinyl pyrrolidone) (PEO/PVP) with various lithium salts were prepared by solvent casting technique. The amorphous nature of the polymer-salt complex was studied by X-ray diffraction analysis. The complexation of the prepared electrolytes was confirmed by Fourier transform infrared analysis. Ionic conductivity as a function of frequency was studied at various temperatures in the range of 303–353 K. The maximum ionic conductivity value was found to be 1.08 × 10^?5 S/cm for the film containing lithium bis trifluoromethane sulfonoimide (LiN[CF₃SO₂]₂) at room temperature and the temperature dependent ionic conductivity values seem to obey Vogel-Tamman-Fulcher relation. Thermogravimetry was used to ascertain the thermal stability of the electrolytes. Photoluminescence measurements demonstrated that the sample having maximum ionic conductivity shows the minimum luminescence intensity. Ultra violet-visible analysis reveals that the values of the band gap energies were changed with the addition of various lithium salts. Porosity of the sample containing lithium bis trifluoromethane sulfonoimide (LiN[CF₃SO₂]₂) was studied by Atomic force microscope.     

Synthesis of networked polymers with lithium counter cations from a difunctional epoxide containing poly(ethylene glycol) and an epoxide monomer carrying a lithium sulfonate salt moiety

Poly(ethylene glycol)‐based networked polymers that had lithium sulfonate salt structures on the network were prepared by heating a mixture of poly(ethylene glycol) diglycidyl ether (PEGGE), poly(ethylene glycol) bis(3‐aminopropyl) terminated (PEGBA), and an ionic epoxy monomer, lithium 3‐glycidyloxypropanesulfonate (LiGPS). Flexible self‐standing networked polymer films showed high thermal stability, low crystallinity, low glass transition temperature, and good mechanical strength. The materials were ion conductive at room temperature even under a dry condition, although the ionic conductivity was rather low (10^?6 to 10^?5 S/m). The ionic conductivity increased with the increase in temperature to above 1 × 10^?4 S/m at 90 °C. The film samples became swollen by immersing in propylene carbonate (PC) or PC solution of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). The samples swollen in PC showed higher ionic conductivity (ca.1 × 10^?3 S/m at room temperature), and the samples swollen in LiTFSI/PC showed much higher ionic conductivity (nearly 1 S/m at room temperature). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3113–3118, 2010     

Investigation on the effect of nanosilica towards corn starch–lithium perchlorate-based polymer electrolytes

Biodegradable corn starch–lithium perchlorate (LiClO₄)-based solid polymer electrolytes with addition of nano-sized fumed silica (SiO₂) were prepared by solution casting technique. Ionic conductivity at ambient temperature was measured by AC impedance spectroscopy. Upon addition of nano-sized SiO₂, the ionic conductivity at room temperature is increased. The optimum ionic conductivity value obtained was 1.23?×?10^?4?S?cm^?1 at 4?wt% SiO₂. This may be attributed to the low crystallinity of the polymer electrolytes resulting from the dispersed nanosilica particles. Fourier–transform infrared spectroscopy studies confirmed the complexation between corn starch, lithium perchlorate, and silica. The thermal properties of the prepared samples were investigated with differential scanning calorimetry and thermogravimetric analysis. The surface morphology of the polymer electrolytes confirmed the agglomeration of particles after excess dispersion of inorganic filler. This was proven in the scanning electron microscopy studies.     

Effect of plasticizers (EC or PC) on the ionic conductivity and thermal properties of the (PEO)9LiTf: Al2O3 nanocomposite polymer electrolyte system

A new plasticized nanocomposite polymer electrolyte based on poly (ethylene oxide) (PEO)-LiTf dispersed with ceramic filler (Al₂O₃) and plasticized with propylene carbonate (PC), ethylene carbonate (EC), and a mixture of EC and PC (EC+PC) have been studied for their ionic conductivity and thermal properties. The incorporation of plasticizers alone will yield polymer electrolytes with enhanced conductivity but with poor mechanical properties. However, mechanical properties can be improved by incorporating ceramic fillers to the plasticized system. Nanocomposite solid polymer electrolyte films (200–600 μm) were prepared by common solvent-casting method. In present work, we have shown the ionic conductivity can be substantially enhanced by using the combined effect of the plasticizers as well as the inert filler. It was revealed that the incorporating 15 wt.% Al₂O₃ filler in to PEO: LiTf polymer electrolyte significantly enhanced the ionic conductivity [σ _RT (max)?=?7.8?×?10^?6 S cm^?1]. It was interesting to observe that the addition of PC, EC, and mixture of EC and PC to the PEO: LiTf: 15 wt.% Al₂O₃ CPE showed further conductivity enhancement. The conductivity enhancement with EC is higher than PC. However, mixture of plasticizer (EC+PC) showed maximum conductivity enhancement in the temperature range interest, giving the value [σ _RT (max)?=?1.2?×?10^?4 S cm^?1]. It is suggested that the addition of PC, EC, or a mixture of EC and PC leads to a lowering of glass transition temperature and increasing the amorphous phase of PEO and the fraction of PEO-Li⁺ complex, corresponding to conductivity enhancement. Al₂O₃ filler would contribute to conductivity enhancement by transient hydrogen bonding of migrating ionic species with O–OH groups at the filler grain surface. The differential scanning calorimetry thermograms points towards the decrease of T _g , crystallite melting temperature, and melting enthalpy of PEO: LiTf: Al₂O₃ CPE after introducing plasticizers. The reduction of crystallinity and the increase in the amorphous phase content of the electrolyte, caused by the filler, also contributes to the observed conductivity enhancement.