FTIR study of gamma-irradiated cis-1,4-polyisoprene

The effect of γ-irradiation on the structure and oxidation of cis-1,4-polyisoprene is investigated by ATR-FTIR technique. This method provides the valuable insight into the type of oxidation products produced and the extent and nature of intramolecular cyclization and chain scission reactions. The formation of ketones, alcohols and/or ethers, and hydroperoxides is apparent already at small doses of γ-radiation and it increases with the exposure time significantly. At the highest dose of 309 kGy a decrease in the intensity of C=O stretching mode of ketones (1717 cm⁻¹) was observed while the overall area of the band remained the same as in the case of 188 kGy dose. The shoulders observed at 1740 cm⁻¹ and 1772 cm⁻¹ could be assigned to C=O stretching frequency of esters and five-membered-ring lactones, respectively. Higher doses of γ-radiation also cause the formation of two relatively strong bands in the region of conjugated double bonds. These could origin from the aromatic products or cycloenes with one double bond formed by cyclization and chain scission processes.     

Chemical modification of neodymium high cis-1,4 polybutadiene with styreneoxide

The polymerization of 1,3-butadiene (BD) was carried out in the presence of a catalyst composed of neodymium 2-ethylhexanoate, triisobutyl aluminum, diisobutyl aluminum hydride (DIBAH), ethylaluminum sesquichloride and acetylacetone. The molecular weight of the BR could be controlled with DIBAH. The reactive polymer was then chemically modified with styreneoxide (STO). The STO content of BR increased with the decrease in the molecular weight of the BR. This polymer was modified by the STO at the chain terminal end. The physical properties of the vulcanizates with the modified BR were measured. The abrasion resistance and the tensile strength were found to be improved.     

Sorption and addition of bromine from aqueous solutions on cis-1,4-polyisoprene

The sorption of bromine from bromine water on cis-1,4-polyisoprene film and the initial stages of bromination are studied at concentrations of 0.002–0.1 mol/l and temperatures of 15–35°C. The diffusion coefficient of bromine into natural rubber (NR) is 1.3–2.0 × 10^?6 cm²/sec for the total sorption and 5–13 × 10^?7 cm²/sec for the irreversible sorption. The partition coefficient of bromine between water and rubber increased from 17.3 at 15°C to 37.1 l/kg at 35°C. The chemical potential, enthalpy and change in entropy of partition are, at 25°C, respectively: ?1.9 kcal/mol, 6.6 kcal/mol and 28.4 cal/mol. K. The irreversible sorption is due to a charge-transfer complex between bromine molecules and double bonds of the rubber. The complex is the first stage of the addition reaction, which becomes noticeable at concentrations above 0.012 mol/l. With increasing bromine concentration the concentration of the complex decreases and the added bromine increases. The charge transfer complex appears to change the conformation of the cis-NR chains so that the bromine addition occurs in the trans-conformation, as shown by FT–IR spectra. The bromination is accompanied by a marked crystallization effect as illustrated by thermal analysis and WAXS measurements.     

Phase structure and crystallization behavior of polyethylene in its blends with cis-1,4-butadiene rubber

Phase structure and crystallization behavior of polyethylene(PE) in its blends with cis-1,4-butadiene rubber(BR) at different blend ratios and sample preparation conditions were studied. The PE is finely dispersed in the BR matrix. For samples hot pressed at 145 °C, circular PE microdomains with randomly oriented PE lamellar aggregates were produced. The domain size and number increase with increasing PE content. When the PE content is over 10 wt%, most of the PE domains impinged each other. The separated PE domains are connected by PE stripes with parallel arranged lamellar aggregates. For samples hot pressed at 140 °C, elongated PE microdomains with oriented PE lamellar aggregates were obtained due to the shear flow. The crystallization of PE in the blends depends on the phase structure. Confined crystallization of PE occurs in small microdomains at relatively low temperature. With the increase of domain size, the crystallization ability of PE increases while the confined crystallization decreases.     

Synthesis of well-defined telechelic trans-1,4-polyisoprene by oxidative cleavage

Synthesis of telechelic trans-1,4-polyisoprenes(TPI: trans-structure 95%) was evaluated based on two different methods of oxidative cleavage(indirect cleavage: first epoxidation of TPI, then the selective cleavage of epoxidized units in epoxidized trans-1,4-polyisoprene(ETPI) and direct cleavage of isoprene units in TPI). The influence of solvents and the ratio of oxidative agents was investigated by 1H-NMR and 13C-NMR. A series of well-defined telechelic TPI with double terminated functional groups and less side reaction(molecular weight distribution range: 1.96?2.26) were synthesized by indirect cleavage in chloroform. Telechelic TPI showed similar crystallization behavior with TPI and interesting cold crystallization behavior characterized by DSC.     

Plasticization and crystallization of cis-1,4 polyisoprene mixed with methyl linolate

Crystallization behavior of synthetic cis-1,4 polyisoprene mixed with methyl linolate was investigated by differential scanning calorimetry and dilatometry. At isothermal crystallization temperature of ?25°C, a rate of crystallization decreased with the addition of 1 wt % methyl linolate, whereas it increased with a large amount of methyl linolate, about 30% by weight. Although Avrami constant of cis-1,4 polyisoprene was 2.82, that of mixtures containing 1 and 30 wt % methyl linolate was found to be approximately 4. This implies the same crystallization mechanism was in operation in the mixtures. Since glass transition temperature, T_g, of cis-1,4 polyisoprene decreased as the methyl linolate content of mixture increased, methyl linolate was found to be plasticizer for cis-1,4 polyisoprene. The increase in the rate of crystallization in the mixtures was corresponding to the decrease in T_g. © 1995 John Wiley & Sons, Inc.     

DSC and FTIR study of the gamma radiation effect on cis-1,4-polyisoprene

The effect of γ-radiation on the cis-1,4-polyisoprene in the presence of oxygen is investigated by ATR-FTIR technique and non-isothermal DSC measurements. FTIR measurements have shown that the formation of hydroperoxides, ketones, alcohols and/or ethers is apparent already at lower, 20–50 kGy, doses of γ-radiation and it increases significantly with the exposure time. Besides, lactones, anhydrides, peresters, carboxylic acids, and esters are formed, too. Spectral changes in the region of C=C conjugated double bonds indicate a formation of shorter polyene structures and aromatic rings. Kinetic parameters describing the temperature dependence of the induction period have been obtained from DSC measurements using the isoconversional method. Residual stabilities have been calculated in order to characterize the gamma radiation effect on polyisoprene thermooxidative stability. Both methods proved that doses lower than 50 kGy do not cause severe changes in polymer properties.     

胶液法制备高顺式端羟基聚丁二烯液体橡胶

以工业顺丁胶原液为起始原料,先经氧化裂解反应制得醛基封端的聚丁二烯液体橡胶,再经还原反应制得了端羟基聚丁二烯液体橡胶.结果表明,反应过程中顺丁胶的微观结构未发生异构化,所得的端羟基聚丁二烯液体橡胶的顺式含量高(cis-1,495%);分子量通过控制氧化裂解反应物与丁二烯结构单元的化学计量比,在2200~7000间可调(~1H-NMR法);分子量分布指数维持在1.5~2.1范围;官能度(fn)在2.0左右.与阴离子聚合型丁羟胶和自由基聚合型丁羟胶相比,氧化裂解法制备的丁羟胶微观结构更规整,顺式含量更高,能够保持极低的玻璃化转变温度.此外,以工业顺丁胶原液为原料,既省去了顺丁块胶生产的水析凝聚、干燥压块等过程,又免去了胶块剪切破碎、溶胀溶解等过程,大幅度减少了能量消耗,且反应条件温和、可控、高效、经济,具有良好的工业化前景.     

Investigation of methylaluminoxane as a cocatalyst for the polymerization of 1,3-butadiene to high cis-1,4-polybutadiene

The catalytic system Co/methylaluminoxane/tert-butyl chloride has been studied and optimized for the polymerization of 1,3-butadiene to high cis-1,4-polybutadiene. The ratio of the individual catalyst components was investigated to achieve maximum conversion, stereoregularity, and molecular weight. It was found that the specific order of addition of catalyst components to the feedstock and aging time therein has critical influence in the polymerization reaction. This can be attributed to the rate of chlorinating the aluminoxane and the stability of the active catalyst sites obtained. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3277–3284, 1999     

The Influence of Flame Retardants on the Thermal Stability of CIS-1,4-Polyisoprene

The effect of flame retardants such as chloroparaffin, antimony trioxide, mixtures of antimony trioxide and chloroparaffin, melamine cyanurate and pentabromotoluene on the thermal properties of cis-1,4-polyisoprene peroxide vulcanizate has been studied. The thermoanalytical curves of elastomers were interpreted. The flame retardants used, except Sb2O3 were found to change the characteristic thermal transitions of polyisoprene and to cause a decrease in its thermal stability. From among the investigated flame retardants only pentabromotoluene favoured the degradation of the elastomer in the range of its first exothermic transition. This revised version was published online in July 2006 with corrections to the Cover Date.     

129Xe NMR as a probe of polymer blends

The miscibility of two-component polymer blends has been investigated using xenon-129 (¹²⁹Xe) nuclear magnetic resonance (NMR) to probe the phase morphology. The chemical shift of ¹²⁹Xe dissolved in a given polymer is unique, thus heterogeneous blends with large domain sizes exhibit two ¹²⁹Xe NMR lines. When a single resonance is obtained, the data are consistent with miscibility, yielding an upper bound on the domain size. The temperature dependence of the relative solubilities and chemical shifts of ¹²⁹Xe dissolved in the pure components may allow a determination of the phase morphology in blends exhibiting a single resonance. The method is used to demonstrate that polychloroprene and 25% epoxidized 1,4-polyisoprene form a miscible blend.     

Evaluation of biodiesel-diesel blends quality using H NMR and chemometrics

In this work, the use of ¹H NMR spectroscopy and statistical approach to the evaluation of biodiesel-diesel blends quality is described. Forty-six mixtures of oil-diesel, biodiesel-diesel, and oil-biodiesel-diesel were analyzed by ¹H NMR and such data were employed to design four predictive models. Thirty-six mixtures were used in the calibration set and the others in the validation. The PCR and PLS models were evaluated through statistical parameters.Briefly, PLS and PCR models were suitable for the prediction of biodiesel and oil concentration in mineral diesel. Specially, in higher concentration the predicted values were quite similar to the real ones. This fact was evidenced by the low relative errors of high concentrated samples; this means that the prediction of low concentrated samples will probably show high deviation. Therefore, ¹H NMR-PLS and ¹H NMR-PCR methods are fairly useful for the quality control of biodiesel-diesel blends, particularly they are suitable for prediction of concentrations greater than 2%.     

Solid-state NMR study of biodegradable starch/polycaprolactone blends

Abundant literature exists on starch or modified starch blended with biodegradable polyesters to achieve good performance with cheap compost plastics. The level of miscibility in these blends is one of the most relevant parameters. In the present study, solid-state ¹H and ¹³C NMR spectra, as well as carbon spin-lattice relaxation times T₁(C) and proton spin-lattice relaxation times T₁(H) and proton spin-lattice relaxation times in the rotating frame T_1ρ(H) of biodegradable starch (or starch formate)/polycaprolactone (PCL) (or polyester (PE) oligomers) blends and samples of the neat components were measured. From the T_1ρ(H) and T₁(H) relaxation times it follows that blends starch/PCL, starch/PE-oligomers and starch formate/PE-oligomers are phase separated even on the scale of 20-110 nm. On the contrary starch formate/PCL blend is phase separated on the scale 2.5-12 nm but homogeneously mixed on the scale 20-90 nm. Moreover, shorter T₁(C) and especially T_1ρ(H) values found for the starch or starch formate component in all these blends in comparison with neat samples show that molecular mobility of starch and starch formate segments is affected by blending. This indicates some miscibility also in phase separated blends which can happen in amorphous channels of starch.     

Fabrication and chemical crosslinking of electrospun <Emphasis Type="Italic">trans</Emphasis>-polyisoprene nanofiber nonwoven

In this work, the optimal electrospinning conditions of trans-polyisoprene (TPI) solutions were evaluated nevertheless its lower glass transition temperature than the room temperature. Subsequently, chemical crosslinking of TPI nonwovens was firstly investigated by vulcanizing at high temperatures in the case of the persistence of nanofiber structure. For this purpose, curing agents of TPI were embedded in TPI nanofibers by co-electrospinning, and then a protect layer was coated on TPI nanofibers by filtering gelatin solution going through TPI nonwoven before the vulcanization at 140?160 °C. The results showed that the vulcanization of TPI fibrous nonwoven at high temperatures did not destroy the fiber morphology. Interestingly, TPI fibrous nonwovens after vulcanization showed excellent mechanical properties (~17 MPa of tensile strength) that could be comparable to or even higher than that of some bulk rubber materials.     

Molecular interpretation of miscibility in polyamide-6 blends with alkali ionomers of sulfonated polystyrene

Blends of polyamide-6 with lithium ionomers of 9.8 and 5.4 mole percent sulfonated polystyrene, formed by combining solutions of these polymers, are miscible over a wide compositional range, but those with the equivalent sodium ionomers are not. The molecular origin of this difference is addressed by studying the far infared and infrared spectra of the blends and pure materials to follow changes in the interactions between the cations and their surroundings, and changes in the interactions between functional groups. Based on analysis of these spectra, a molecular level interpretation of the blending is proposed. The initial step involves both the interaction of one amide carbonyl with an Li⁺ ion and simultaneous hydrogen bonding between an amide N? H and a sulfonate group. This eventually leads to formation of an Li(>CO)⁺_n(n ～ 4) entity while the sulfonates are converted to the acid form through hydrogen bonding to the amide N? H groups. The Na⁺ ion does not interact strongly enough with the amide groups to leave its sulfonate environment to a significant extent. © 1995 John Wiley & Sons, Inc.     

Transition from miscibility to immiscibility in blends of poly(methyl methacrylate) and styrene-acrylonitrile copolymers with varying copolymer composition: a DSC study

The glass transition and the structural relaxation processes have been studied in blends of poly(methyl methacrylate) (PMMA) and styrene-acrylonitrile (SAN) copolymers with different acrylonitrile (AN) contents. The 50/50 wt.% blend of PMMA with the SAN copolymer containing 30 wt.% of AN is immiscible, while blends with copolymers containing between 13 and 26 wt.% of AN are miscible. Thus the upper limit of miscibility is between 26 and 30 wt.% of AN. The temperature dependence of the relaxation times of the conformational rearrangements of polymer chains around the glass transition have been determined in the blends and pure components by modelling DSC thermograms obtained after different thermal histories in each sample. The slope in the Arrhenius diagram logτ vs 1/T around the glass transition temperature is significantly smaller in the blend which is closer to the upper limit of miscibility than in the other miscible blends in which SAN copolymer contains less AN. The change of slope can be ascribed to a distribution in the glass transition temperatures of the different rearranging regions, reflecting the appearance of a microheterogeneity in the blend that cannot be detected as a double glass transition in the blend.     

Characterizing blends of linear low-density and low-density polyethylene by DSC

Summary A two-step isothermal annealing (TSIA) procedure is described that enables the endothermic peaks of low-density polyethylene (LDPE), linear low-density polyethylene (LLDPE) and their blends, to be satisfactorily resolved during analysis by differential scanning calorimetry. A modified form of multistep isothermal annealing, the TSIA procedure produces a highly characteristic profile of the blend components by facilitating the segregation of the phases based on branch density. It is proposed that the TSIA procedure may have significant merit in the identification and quantification of the components in an unknown blend as well as increasing the sensitivity in analytical procedures aimed at blend component quantification.     

Monte Carlo simulation of miscibility of polymer blends with repulsive interactions: effect of chain structure

The effects of the chain structure and the intramolecular interaction energy of an A/B copolymer on the miscibility of the binary blends of the copolymer and homopolymer C have been studied by means of a Monte Carlo simulation. In the system, the interactions between segments A, B and C are more repulsive than those between themselves. In order to study the effect of the chain structure of the A/B copolymer on the miscibility, the alternating, random and block copolymers were introduced in the simulations, respectively. The simulation results show that the miscibility of the binary blends strongly depends on the intramolecular interaction energy () between segments A and B within the A/B copolymers. The higher the repulsive interaction energy, the more miscible the A/B copolymer and homopolymer C are. For the diblock copolymer/homopolymer blends, they tend to form micro phase domains. However, the phase domains become so small that the blend can be considered as a homogeneous phase for the alternating copolymer/homopolymer blends. Furthermore, the investigation of the average end-to-end distance () in different systems indicates that the copolymer chains tend to coil with the decrease of whereas the of the homopolymer chains depends on the chain structure of the copolymers. As for the system containing the alternating or the random copolymers, the homopolymer chains also tend to coil with the decrease of . However, for the systems including the block copolymers, there is a slight difference in the of the homopolymer chains with the variation of .     

Effect of carbon black on the thermal properties and flammability of cis-1,4-polyisoprene vulcanizates

The effect of carbon black with various particle sizes and specific surfaces on the thermal properties of the sulphur vulcanizates ofcis-1,4-polyisoprene was studied by means of thermal analysis. It was found that the addition of carbon black does not change the nature of the thermal processes in isoprene rubber vulcanizates essentially, but it distincly affects the positions of the peaks recorded in the DTA curves. The specific surface of carbon black affects the temperature of the first exothermic process and the temperature and rate of destruction of cross-linked polyisoprene. The presence of carbon black brings about a reduction in the flammability ofcis-1,4-polyisoprene vulcanizates. The specific surface of carbon black influences the value of the oxygen index OI.

---

Zusammenfassung Mittels Thermoanalyse wurde der Einfluß von Ruß mit unterschiedlicher Partikelgröße und unterschiedlicher spezifischer Oberfläche auf die thermischen Eigenschaften von Schwefelvulkanisaten von cis-1,4-Polyisopren untersucht. Es wurde festgestellt, daß die Zugabe von Ruß die thermischen Vorgänge in Isoprengummivulkanisaten nicht wesentlich verändert, daß jedoch die Lage der in den DTA-Kurven aufgezeichneten Peaks eindeutig beeinflußt wird. Die spezifische Oberfläche von Ruß beeinflußt die Temperatur des ersten exothermen Vorganges sowie Temperatur und Geschwindigkeit von Abbau des vernetzten Polyisoprenes. Die Gegenwart von Ruß führt eine Verminderung der Entflammbarkeit voncis-1,4-Polyisopren-Vulkanisaten herbei. Die spezifische Oberfläche von Ruß beeinflußt den Wert der Sauerstoffzahl.

     

Synthesis and Characterization of New CIS-1,4-Diaminocyclohexane and Piperidine Platinum(II) Complexes Containing Disubstituted Sulfide Groups

Abstract

A series of cationic platinum(II) complexes of the type [Pt(cis-1,4-DACH)(R′R″S)Cl]NO₃ and [Pt(PIP)₂(R′R″S)Cl]NO₃ (where cis-1,4-DACH = cis-1,4-diaminocyclohexane; PIP = piperidine; and R′R″S = dimethylsulfide, diethylsulfide, dipropylsulfide, diisopropylsulfide, dibutylsulfide, diphenylsulfide, dibenzylsulfide, methylphenylsulfide, or methyl-p-tolylsulfide) have been synthesized and characterized by elemental analysis and infrared, ¹H, and ¹⁹⁵Pt nuclear magnetic resonance spectroscopy.