Polystyrene(1)/poly(butyl acrylate-methacrylic acid)(2) core-shell emulsion polymers. Part II: Thermomechanical properties of latex films

Polystyrene(1)/poly(n-butyl acrylate-methacrylic acid)(2) structured latex particles were prepared through a two-stage emulsion polymerization procedure, using a polystyrene (PS) latex seed (118 nm), and differentn-butyl acrylate (BA)/methacrylic acid (MAA) ratios. Polymerization kinetics, particle morphology, and MAA location have already been discussed in the first part of this series. In this second part the thermomechanical behavior of films cast from these latexes was studied. Differential Thermal Analysis and Dynamic Mechanical Analysis (DMA) were employed as characterization techniques for the films. Two polymer phases corresponding to polystyrene and a poly(BA-MAA) copolymer were distinguished. Comparison was made to analogous unfunctionalized PS/PBA systems, as a result of which an effect of MAA upon the phase arrangement in the film was found. Scanning Electron Microscopy of film samples and DMA showed that the evolution of the phase arrangement as a result of annealing was strongly dependent on the type of mechanical and heat treatments being applied to functionalized systems. Finally, the thermomechanical behavior of films was related to the structural features of the corresponding latexes, and computer simulation techniques wer eemployed to establish a mechanistic support for these relationships.     

Surface functionalization of styrene/butyl acrylate latex with a water‐soluble monosaccharide monomer. Synthesis and morphology of the polymer particles

New polymer latexes bearing saccharide moieties on the particle surface were synthesized by using a water‐soluble sugar monomer, such as 1‐deoxy‐1‐methacryl‐amido‐D ‐glucitol, (MAG). All the latexes were prepared by a two‐stage emulsion polymerization technique. In the first step, the core was prepared with butyl acrylate (BA) and styrene (St). In the second step, the seed latex was polymerized with ethyl acrylate (EA) and MAG. The influence of a bifunctional monomer such as allyl methacrylate (ALMA), introduced at various concentrations, on the final latexes morphologies and properties was investigated. It was found that the latex particles exhibit a core‐shell structure. The mass balance of MAG showed that the main part of the sugar moiety is on the shell layer. The molecular properties, such as structure, composition, and molecular weight, were determined by elemental analysis, ¹H‐ and ¹³C‐NMR spectroscopy. Colloidal (particle size and their distributions), thermal, and rheological properties were also studied. Copyright © 2003 John Wiley & Sons, Ltd.     

Synthesis and characterization of poly (n-butyl acrylate)-poly (methyl methacrylate) latex interpenetrating polymer networks by radiation-induced seeded emulsion polymerization

A series of latex interpenetrating polymer networks (LIPNs) were prepared via a two-stage emulsion polymerization of methyl methacrylate (MMA) or mixture of MMA and n-butyl acrylate (n-BA) on crosslinked poly(n-butyl acrylate)(PBA) seed latex using ⁶⁰Co γ-ray radiation. The particles of resultant latex were produced with diameters between 150 and 250 nm. FTIR spectra identified the formation of crosslinked copolymers of PMMA or P(MMA-co-BA). Dynamic light scattering (DLS) showed that with increasing n-BA concentration in second-stage monomers, the particle size of LIPN increased. Transmission electron microscope(TEM) photographs showed that the morphology of resultant acrylate interpenetrating polymer network (IPN) latex varied from the distinct core-shell structure to homogenous particle structure with the increase of n-BA concentration, and the morphology was mainly controlled by the miscibility between crosslinked PBA seed and second-stage copolymers and polarity of P(MMA-co-BA)copolymers. In addition, differential scanning calorimeter (DSC) measurements indicated the existence of reinforced miscibility between PBA seed and P(MMA-co-BA)copolymer in prepared LIPNs.     

Polystyrene(1)/poly(butyl acrylate-methacrylic acid)(2) core-shell emulsion polymers. Part I. Synthesis and colloidal characterization

Polystyrene (PS) (1)/Poly(n-butyl acrylate (BA)-methacrylic acid (MAA)) (2) structured particle latexes were prepared by emulsion polymerization using monodisperse polystyrene latex seed (118 nm) and different BA/MAA ratios. Three main aspects have been investigated: i) the polymerization kinetics; ii) the particle morphology as a function of reaction time; iii) the distribution of MAA units between the water phase and the polymer particles.The amount of MAA in the shell copolymer was found to be the main factor controlling the particle shape and morphology. The shape of the structured particles was, generally, non-spherical, and the shape irregularities increased as a particles was, generally, non-spherical, and the shape irregularities increased as a function of reaction time. At the beginning of the second stage reaction, new small particles were observed, which coalesced onto the PS seed as the polymerization proceeded. The distribution of the MAA groups in the latex particles and the serum was analyzed by alkali/back-acid titration, using ionic exchanged latexes. No MAA groups were detected in the latex serum. Due to the lowTg of the BA-MAA copolymers, alkali conductimetric titrations accounted for all the MAA groups on and within the polymer particles. Therefore, for these systems, this method is not only limited to a thin surface layer, as it is often assumed.     

Synthesis and morphology of Fe3O4/polystyrene/poly(isopropylacrylamide‐co‐methyl acrylate acid) magnetic composite latex – 2,2′‐azobis (2‐methylpropionamidine) dihydrochloride as initiator

In this work, Fe₃O₄/polystyrene/poly(N‐isopropylacryl amide‐co‐methylacrylate acid) (Fe₃O₄/PS/P(NIPAAM‐co‐MAA)) magnetic composite latex was synthesized by the method of two stage emulsion polymerization. In this reaction system, 2,2′‐azobis(2‐methyl propionamidine) dihydrochloride (AIBA) was used as initiator to initiate the first stage reaction and second stage reaction. The Fe₃O₄ particles were prepared by a traditional coprecipitation method. Fe₃O₄ particles were surface treated by either PAA oligomer or lauric acid to form the stable ferrofluid. The first stage for the synthesis of magnetic composite latex was to synthesize PS in the presence of ferrofluid by soapless emulsion polymerization to form the Fe₃O₄/PS composite latex particles. Following the first stage of reaction, the second stage of polymerization was carried out by the method of soapless emulsion polymerization with NIPAAM and MAA as monomers and Fe₃O₄/PS latex as seeds. The magnetic composite particles, Fe₃O₄/PS/P(NIPAAM‐co‐MAA), were thus obtained. The mechanism of the first stage reaction and second stage reaction were investigated. Moreover, the effects of PAA and lauric acid on the reaction kinetics, morphology, and particle size distribution were studied. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3912–3921, 2007     

Synthesis,surface properties,and morphologies of poly[methyl(3,3,3‐trifluoropropyl)siloxane]‐b‐polystyrene‐b‐poly(tert‐butyl acrylate) triblock copolymers by a combination of anionic ROP and ATRP

A series of well‐defined poly[methyl(3,3,3‐trifluoropropyl)siloxane]‐b‐polystyrene‐b‐poly(tert‐butyl acrylate) (PMTFPS‐b‐PS‐b‐PtBA) triblock copolymers were prepared by a combination of anionic ring‐opening polymerization of 1,3,5‐trimethyl‐1,3,5‐tris(3′,3′,3′‐trifluoropropyl)cyclotrisiloxane (F₃), and atom transfer radical polymerization (ATRP) of styrene (St) and tert‐butyl acrylate (tBA), using the obtained α‐bromoisobutyryl‐terminal PMTFPS (PMTFPS‐Br) as the macroinitiators. The ATRP of St from PMTFPS‐Br, as well as the ATRP of tBA from the obtained PMTFPS‐b‐PS‐Br macroinitiators, has typical characteristic of controlled/living polymerization. The results of contact angle measurements for the films of PMTFPS‐b‐PS‐b‐PtBA triblock copolymers demonstrate that the compositions have an effect on the wetting behavior of the copolymer films. For the copolymer films with different compositions, there may be different macroscale or nanoscale structures on the outmost layer of the copolymer surfaces. The films with high content of PtBA blocks exhibit almost no ordered microstructures on the outmost layer of the copolymer surfaces, even though they have microphase‐separated structures in bulk. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012