Separation of uranium(VI) and transition metal ions with 4-(2-thiazolylazo)resorcinol by capillary electrophoresis

A capillary electrophoresis method utilizing 4-(2-thiazolylazo)resorcinol (TAR) was developed to separate uranium, cobalt, cadmium, nickel, titanium and copper metal ions. TAR was chosen as the visible absorbing chelating ligand because of its ability to form stable complexes with a wide variety of metals. Several parameters that included pH, electrophoretic run buffer concentration, buffer type and the influence of chelating ligand in the electrophoretic run buffer were examined to determine the best separating conditions. Optimum separation of the six metal chelates was achieved in a 15 mM Na2B4O7-NaH2PO4, pH 8.3 buffer containing 0.1 mM TAR. Method validation included injection and method precision studies as well as detection limit and linear dynamic range determination. High-ppb to low-ppm (w/w ratio) detection limits were achieved with linear dynamic ranges between 0.1 and 75 ppm.     

中空纤维膜固定化甲酸脱氢酶催化CO_2合成甲酸

以紫外光表面接枝改性的聚乙烯(PE)中空纤维膜为载体,采用共价结合的方式固定化甲酸脱氢酶(FDH),考察了CO2通入方式、溶液pH值、缓冲液种类和还原型烟酰胺腺嘌呤二核苷酸(NADH)的浓度对酶催化CO2合成甲酸反应的影响.结果表明,与加压法相比,CO2鼓泡法更有利于甲酸的生成;磷酸盐缓冲液优于Tris-HCl和盐酸三乙醇胺缓冲液;体系pH值对反应的影响较大,固定化FDH的最佳pH值仍为6.0,但pH耐受性增强;随着辅酶NADH浓度的增加,反应初速度加快,收率下降;游离酶和固定化酶的最大酶活分别为0.246和0.138mmol/(L.h);固定化FDH在4℃贮存两周后活性仅下降4%,而游离酶活性下降50%.FDH催化膜重复利用10次后,活性没有明显降低.     

Purity control of oxytetracycline by capillary electrophoresis

The applicability of capillary electrophoresis for the purity control of oxytetracycline (OTC) was investigated. OTC is a broad-spectrum antibiotic belonging to the group of the tetracyclines. Several related substances can be present due to fermentation or degradation, such as 4-epioxytetracycline, -apooxytetracycline, β-apooxytetracycline, anhydrooxytet racycline, 2-acetyl-2-decarboxamidooxytetracycline, tetracycline and 4-epitetracycline. Using fused-silica capillaries, the influence of buffer type, buffer pH and buffer concentration were investigated. In all cases 1 mM EDTA was added to prevent metal-ion complexation. The influence of the buffer counter-ion type was examined. Consequently, some instrumental parameters were changed such as capillary length and diameter as well as capillary temperature and applied voltage. The following method is finally proposed: fused-silica capillary, l (effective length) = 38 cm, L (total length) = 44 cm, 50 μm I.D.; buffer, sodium carbonate 20 mM-EDTA 1 mM, pH 11.25; voltage, 10 kV; temperature, 10°C. Linearity, limit of detection and limit of quantitation were determined as well as the relative standard deviations for all the analytes involved. This method is less selective then existing liquid chromatographic methods but it may be used as a complementary tool in purity control and stability studies.     

高选择性高效液相色谱-电化学检测法测定丹参中5种酚类物质

发展了一种高灵敏度的高效液相色谱-电化学检测（HPLC-ECD）方法,用于丹参中5种酚类物质的定量分析。为了获得较高的检测灵敏度,对流动相的pH、缓冲溶液类型和浓度、有机相种类和梯度以及流速做了系统研究。在较低的pH（2.8）、较低的缓冲盐浓度（20 mmol/L NaH₂PO₄）和较缓的乙腈梯度下,以0.2 mL/min流速可为5种酚类的分离检测提供较好的分离度和较高的检测灵敏度。在获得优化的分离参数后,将其用于14批丹参药材中5种酚类物质的定量分析。结果表明,该方法可获得较好的回收率（>95%）、较宽的线性范围（高达4个数量级）、较好的重复性（RSD<4.01%）和较高的灵敏度（咖啡酸的LOQ低至1.5μg/L）。与紫外检测方法相比,ECD检测方法具有更高的选择性,可减少非抗氧化活性的物质的干扰。     

Chiral CE of aromatic amino acids by ligand-exchange with zinc(II)-L-lysine complex

A novel method of chiral ligand-exchange CE was developed with either L- or D-lysine (Lys) as a chiral ligand and zinc(II) as a central ion. This type of chiral complexes was explored for the first time to efficiently separate either individual pairs of or mixed aromatic amino acid enantiomers. Using a running buffer of 5 mM ammonium acetate, 100 mM boric acid, 3 mM ZnSO(4) x 7H(2)O and 6 mM L-Lys at pH 7.6, unlabeled D,L-tryptophan, D,L-phenylalanine, and D,L-tyrosine were well separated, giving a chiral resolution of up to 7.09. The best separation was obtained at a Lys-to-zinc ratio of 2:1, zinc concentration of 2-4 mM and running buffer pH 7.6. The buffer pH was determined to have a strong influence on resolution, while buffer composition and concentration impacted on both the resolution and peak shape. Boric acid with some ammonium acetate was an adoptable buffer system, and some additives like ethylene diamine tetraacetic acid capable of destroying the complex should be avoided. Fine-tuning of the chiral resolution and elution order was achieved by regulating the ratio of L-Lys to D-Lys; i.e. the resolution increased from zero to its highest value as the ratio ascended from 1:0 to 1:infinitive, and L-isomers eluted before or after D-isomers in excessive D- or L-Lys, respectively.     

Analysis of post-harvest fungicides by micellar electrokinetic chromatography

A method based on solid-phase extraction (SPE) and micellar electrokinetic chromatography (MEKC) was developed for the simultaneous determination of carbendazim, imazalil, methylthiophanate, O-phenylphenol, prochloraz, procimidone, thiabendazole and triadimefon residues in grape, lettuce, orange and tomato. Selectivity and resolution were studied changing the pH and the concentration of the buffer, the type and concentration of surfactant and the methanol content in the mobile phase. A buffer consisting of 4 mM borate with 75 mM sodium cholate (pH 9.2) gave the best results. The recoveries of the fungicides in spiked fruit and vegetable samples ranged from 30 to 105%, and the limits of detection were between 0.1 and 1 mg kg(-1). The reproducibility and repeatability of the combination of SPE pretreatment and MEKC were good for all the compounds, except for imazalil and O-phenylphenol in oranges, due to some matrix compounds interfering with the separation. The method was applied to post harvest treated samples, and the fungicides were sometimes detected at concentration levels lower than maximum residue limits (MRLs).     

水溶性汞离子(Ⅱ)荧光离子液体探针1-丁基-2-苯基硫脲吡啶溴化盐的合成及分析应用

设计、合成了1-丁基-2-苯基硫脲吡啶溴化盐（[C4ptpyr]Br）新型的水溶性Hg2+荧光探针,将其用于环境水样中Hg2+的检测。 结果表明,[C4ptpyr]Br对Hg2+识别专一性好,共存离子及pH值对测定影响小。 在pH=7的BR缓冲溶液中,检测线性范围为0.02～4 mg/L(r2=0.999 1),检出限为0.011 mg/L,回收率为95.2%～102.2%, RSD＜5%。 方法具有灵敏度和准确度高、分析速度快、操作简便等特点,可满足各类水中微量汞的测定要求。     

Enantioseparation of warfarin and its metabolites by capillary zone electrophoresis

A capillary zone electrophoresis (CZE) method with direct ultraviolet (UV)-absorbance detection is presented for the simultaneous enantiomeric separation of warfarin and its main metabolites, including warfarin alcohols, 4'-, 6-, and 7-hydroxywarfarin, using highly sulfated beta-cyclodextrin (HS-beta-CD) as the chiral selector. This chiral separation method was optimized in terms of the electrophoretic parameters, which included the concentration of HS-beta-CD used, the type and composition of organic modifier added to the background electrolyte (BGE) buffer, and the BGE buffer pH. Chiral separation of warfarin and its major metabolites was achieved with high resolution, selectivity, efficiency, repeatability, and reproducibility. This optimized chiral analysis of warfarin along with its metabolites was completed within a satisfactory electrophoresis time of 20 min.     

The effect of electric field strength,buffer type and concentration on separation parameters in capillary zone electrophoresis

Summary Probe solutes were used to investigate the effect of buffer type, concentration and applied voltage on solute mobility, column efficiency and resolution in capillary zone electrophoresis. With low conductivity buffers higher concentrations and/or higher voltages could be used to improve column efficiency and resolution. Doubling the concentration of the buffer doubles the amount of heat generated inside the column while doubling the applied voltage cause a 4-fold increase. Solute migration time is approximately an inverse function of the charge density of the buffer's cation. Analysis time is increased by about 30% if the buffer concentration is doubled while it is cut in half if the applied voltage is doubled. Column efficiency is improved (higher theoretical plate count) with increasing buffer concentration and/or applied voltage as long as the heat generated is efficiently dissipated. The separation factor is directly related to analysis time and, therefore, selectivity improves with increasing buffer concentration but decreases with increasing applied voltage. Hence, resolution is optimized by increasing buffer concentration at a moderate applied voltage.     

Capillary electrophoretic and micellar electrokinetic separations of asymmetric dimethyl-L-arginine and structurally related amino acids: quantitation in human plasma

We report the development of efficient electrophoretic methods for the separation and quantification of L-arginine and six naturally occurring derivatives that are structurally and functionally related. Capillary electrophoresis (CE) employing a concentrated borate buffer at pH 9.4 achieves the separation of mixtures containing dimethyl-L-arginine, NG-monomethyl-L-arginine, L-arginine, L-homoarginine, L-ornithine, and L-citrulline as 4-fluoro-7-nitrobenzofurazan derivatives. In addition, the separation of the isomeric dimethyl-L-arginine derivatives (symmetric and asymmetric) is attained with baseline resolution by micellar electrokinetic chromatography (MEKC) when a high concentration of deoxycholic acid is added as a surfactant to the same running buffer. The influence of buffer type, concentration, and pH on the separation was studied to optimize separation conditions. The limit of quantitation (LOQ) for asymmetric dimethyl-L-arginine in aqueous solution was determined to be 20 microM using UV absorption in a CE separation and 0.1 microM using laser induced fluorescence (LIF) detection in an MEKC separation. This newly developed method was successfully applied for the quantitation of asymmetric dimethyl-L-arginine and L-arginine in human plasma samples at levels that might be used as a clinical diagnostic for cardiovascular disease (0.125 microM LOQ).     

Macrocyclic polyamine as a selective modifier in a bonded-phase capillary column for the electrophoretic separation of aromatic acids.

The use of a macrocyclic polyamine, 28[ane]-N6O2, as a selective modifier in a bonded-phase capillary column for the electrophoretic separation of 14 aromatic acids is described. Parameters that affect the performance of the separations, such as the type of buffer, the pH and concentration of buffer, the applied potential and the injection mode were studied. By changing the buffer pH (4.0-5.0), buffer concentration (10-50 mM) and applied potential (-10 approximately -20 kV), optimum conditions were obtained at -20 kV, using an acetate buffer (20 mM, pH 4.5), hydrodynamic injection with a vacuum at the buffer reservoir on the detector side and detection at 220 nm. The results showed that the separation was effective under these conditions. The plate number was greater than 4 x 10(4) m-l. Due to the wide variation in the mobilities of the test compounds, injection studies suggested that a vacuum at the buffer reservoir on the detector side would produce a result that is more representative of the initial sample composition. Benzoic acid in soy sauce, salicylic acid in Salic ointment and Aspirin were sampled and analyzed using the established conditions.     

Enantiomer Separation of the Four Stereoisomers of 1-(4-Hydroxy-3-Methoxy)-Phenyl-2-[4-(1,2,3-Trihydroxy-Propyl)-2-Methoxy]-Phenoxy-1,3-Propandiol from Hydnocarpus annamensis by Capillary Zone Electrophoresis with HP-β-CD as Chiral Selector

A capillary zone electrophoresis method with HP-β-CD as chiral selector was established for the chiral separation of four stereoisomers of 1-(4-hydroxy-3-methoxy)-phenyl-2-[4-(1,2,3-trihydroxy-propyl)-2-methoxy]-phenoxy-1,3-propandiol for the first time, which were isolated from Hydnocarpus annamensis. The effects of chiral selector type and concentration, buffer composition, pH and concentration, and cartridge temperature on the enantioseparation were investigated. A baseline separation of the four stereoisomers was achieved in less than 18 min under the optimized conditions: 40 mmol L⁻¹ Borax–NaOH buffer (pH 10.02) in the presence of 100 mmol L⁻¹ HP-β-CD at 15°C and 30 kV. The experimental results showed that the method by capillary zone electrophoresis for the separation of four stereoisomers is powerful, sensitive and fast, requires less amounts of reagents, and can be employed as a reliable alternative to other methods.     

Capillary electrophoresis with capacitively coupled contactless conductivity detection for low molecular weight organic acids in different samples

CE with capacitively coupled contactless conductivity detection (CE-C(4)D) was explored and validated for the identification and quantification of organic acids in various types of samples. The analyses were performed under optimized conditions, using a buffer system composed of 20 mM MES-histidine (His), pH 6.0, 0.1 mM CTAB, 0.025% HP-beta-CD, and 10% methanol. The investigation included a study of the effects of buffer pH, concentration of CTAB, type and concentration of organic additives, on the migration behavior, resolution and selectivity of the organic acids. The intra- and interday RSDs (n = 6) obtained for migration time and peak area were typically in the range of 0.12-2% and 0.5-4%, respectively. Linearity, detection limits, and repeatability were evaluated. In order to evaluate the application potential of the developed method, real samples from different sources were analyzed. The results demonstrate that CE-C(4)D is a versatile tool for analyzing organic acids in beverages, Chinese herbal medicines (CHM) and plants as it allows for their detection, identification, and quantification.     

Chiral capillary electrophoretic analysis of the enantiomeric purity of a pharmaceutical compound using sulfated beta-cyclodextrin

A practical chiral capillary electrophoresis method using randomly sulfated beta-cyclodextrin was developed for the quantitative determination of the chiral purity of a pharmaceutical compound. A systematic method development approach was conducted by modifying selected parameters such as the concentration of the chiral selectors, buffer pH, organic modifiers, buffer concentrations and type, temperature and applied voltage. The results of the investigation permitted an improved understanding of the separation mechanism. Two facile strategies for the reversal of the enantiomer elution order are also described. The optimized method was validated in terms of variability of the chiral selector, linearity, sensitivity, accuracy, recovery, ruggedness, and precision.     

毛细管区带电泳对手性药物盐酸美西律和盐酸异博定的对映体分离

应用环糊精-毛细管区带电泳体系对手性药物盐酸美西律和盐酸异博定的对映体分离进行了研究。结果表明, 在所研究的手性选择剂α-环糊精, β-环糊精, 二甲基-β-环糊精, 羟丙基β-环糊精和γ-环糊精中, 羟丙基β-环糊精对所研究的手性药物分离效果较好。对盐酸美西律和盐酸异博定的最佳羟丙基-β-环糊精浓度分别为30mmol/L和9mmol/L, 最佳缓冲溶液浓度为100mmol/L Tris-H3PO4(pH2.3)。向缓冲溶液中加入0.05%羟丙基纤维素(HPLC)可改善分离。盐酸美西律获得了接近基线的手性分离, 而盐酸异博定亦获得了较好的分离。     

Simultaneous Determination of Dopamine,Epinephrine and 5-Hydroxytryptamine in Toad Venom and Common Yam Rhizome by MEKC

A micellar electrokinetic chromatography method was developed for the simultaneous determination of dopamine, epinephrine and 5-hydroxytryptamine. Several experimental parameters such as surfactant type and concentration, buffer concentration and pH, type and concentration of organic modifier were evaluated for the analysis of the studied compounds. Among the investigated separation conditions, the composition of micelles, pH and the methanol concentration were the critical parameters. Dopamine, epinephrine and 5-hydroxytryptamine were separated and determined successfully within 7.5 min in Toad venom and Common yam rhizome under the optimum conditions.

     

微芯片毛细管电泳法快速测定黄花鱼中的碱性嫩黄O

采用微芯片毛细管电泳非接触电导检测法,对黄花鱼中非法添加的工业染料碱性嫩黄O进行了分析。 探讨了缓冲液种类、浓度,分离电压和进样时间等因素对分离检测的影响。 实验选择5.0 mmol/L乳酸缓冲液(pH=3.29)、1.8 kV分离电压,在1.0 min内实现了碱性嫩黄O的快速分离测定。 在优化条件下,碱性嫩黄O浓度的线性范围为5.0～100.0 mg/L,黄花鱼中碱性嫩黄O的检出限为0.2 mg/kg,该法可成功测定黄花鱼中碱性嫩黄O的含量。     

肝糖选择剂-毛细管电泳手性拆分盐酸度洛西汀对映体及分离机制

以肝糖为毛细管电泳手性选择剂,对盐酸度洛西汀对映体的分离进行研究,建立了拆分方法.考察了手性选择剂浓度、运行缓冲液的离子强度、pH值及分离电压对手性分离的影响.在3.0% (m/V)肝糖、50 mmol/L Tris-H3PO4(pH 3.0)的运行缓冲液中,分离电压25 kV时,盐酸度洛西汀两对映体分离度达1.84.对分离机制进行了初步探讨.     

Enantiomeric analysis of methotrexate in pharmaceuticals by cyclodextrin-modified capillary electrophoresis

A capillary electrophoresis for the chiral separation of racemic methotrexate (rac-MTX) was developed and validated. The two enantiomers were separated by using fused-silica capillary and a running buffer containing phosphate and hydroxypropyl-β-cyclodextrin (HP-β-CD). Several parameters were studied, including concentration and pH of phosphate buffer, separation voltage, and type and concentration of CD. The quantitative ranges were 12.5-200.0 μM for each enantiomer. The intra- and inter-day relative standard deviations (R.S.D.) and relative errors (R.E.) (n=5) were all <5%. The detection limits were found to be about 4 μM (S/N=3, injection 5 s) at 280 nm. All recoveries were greater than 93%. This method was applied to the assay of l-MTX in pharmaceuticals.     

A Novel Voltammetric Method for the Determination of Maleic Acid Using Silver Amalgam Paste Electrode

An efficient voltammetric method was developed for the determination of maleic acid at a silver amalgam paste electrode (AgA‐PE) in Britton–Robinson buffer pH 2.0. The experimental parameters, such as pH of Britton–Robinson buffer, type of the supporting electrolyte and activation of the electrode surface were optimized. Under the optimal conditions, a linear response was observed over the 2×10^?6–1×10^?4 mol L^?1 maleic acid concentration range, determination limit being 5×10^?7 mol L^?1. A highly stable response, with a relative standard deviation (RSD) of 1.6% for 45 repetitive measurements of 1×10^?4 mol L^?1 maleic acid showed that there was no apparent surface passivation indicating the suitability of the method. The method was successfully applied for direct determination of maleic acid in drinking and river water.