Water sorption/desorption kinetics in poly(ethylene naphthalene-2,6-dicarboxylate) and poly(ethylene terephthalate)

Water sorption/desorption experiments were carried out on films (～ 220 μm thick) of amorphous poly(ethylene naphthalene-2,6-dicarboxylate) (PEN) stored in ambient conditions for different periods of time (0.5-4 years) and of poly(ethylene terephthalate) (PET) with different degrees of crystalinity levels (0-29%) by means of FTIR spectroscopy. Water sorption/desorption kinetics follows Fick's law for all samples investigated. Water sorption isotherms, obtained from gravimetric methods, indicate a larger sorption capacity in the case of PEN materials. The apparent diffusion coefficients (D) are larger in the case of PET samples. The observed D values decrease with storage time (physical aging) of PEN samples and with the crystallinity of PET samples. © 1995 John Wiley & Sons, Inc.     

Magic angle carbon-13 NMR study of solid poly(ethylene naphthalene-2,6-dicarboxylate)

Amorphous (1) and semicrystalline (2) samples of poly(ethylene naphthalene-2,6-dicarboxylate) (PEN) have been investigated by cross-polarization/magic angle spinning (CP/MAS) ¹³C NMR at 26°C (1 and 2), 100°C (1) and 120°C (2) in order to study the phase structure and the local motion of polymer chain segments at temperatures below and close to T_g (120°C). The lineshape of the ethylene unit ¹³C signal in sample 2 is consistent with the presence of two components which were assigned to trans and gauche conformations. The first component arises mainly from the crystalline regions and the second one from the amorphous part. Cross-polarization curves were traced by changing the contact time between carbon and proton reservoirs. T_CH (cross relaxation time) and proton T_1p (spin-lattice relaxation time in the rotating frame) values were obtained as best fit parameters by fitting calculated curves to the experimental data. All ¹³C NMR data are consistent with the presence of highly rigid ethylene units in both semicrystalline and amorphous samples within the temperature range (T) investigated. This result is in disagreement with the ¹H NMR wide line spectra which showed a noticeable narrowing of the linewidth with increasing temperature in the same range, hence indicating a great mobility of the chain segments. To account for this discrepancy a qualitative model based on the existence of two distinct dynamic regions, one where motion is highly restricted and the other one where large reorientations of ethylene group torsional angles take place, is suggested. The NMR results led to the conclusion that three structural phases are present in PEN: crystalline, very rigid amorphous, and very mobile amorphous. © 1995 John Wiley & Sons, Inc.     

The production and properties of poly(ethylene naphthalate-2,6-dicarboxylate) monofilaments

Experimental spinning and drawing conditions are described for poly(ethylene naphthalate-2,6-dicarboxylate), PEN, which produce good quality 0.5 mm monofilaments with high strength and uniformity. Mechanical properties were measured for a range of draw temperatures and draw ratios and an initial modulus of 22 GPa and a strength of 0.6 GPa were obtained by single stage drawing to a draw ratio of 6.6. The maximum birefringence achieved by single stage drawing was 0.33 compared with a theoretical maximum of 0.332 calculated from the bond polarizabilities and bond angles of the aligned monomer unit. Network parameters relevant to undrawn PEN and to the early stages in the drawing process were derived from simple rubber elasticity theory by making birefringence and shrinkage force measurements on films drawn homogeneously to low draw ratios. These suggest that the PEN network contains relatively stiff chains between entanglements and that the PEN network is modified much more in the drawing process than is the case with poly(ethylene terephthalate). A new method of measuring the birefringence of highly drawn thick filaments is described.     

Selective production of benzene and naphthalene from poly(butylene terephthalate) and poly(ethylene naphthalene-2,6-dicarboxylate) by pyrolysis in the presence of calcium hydroxide

Poly(butylene terephthalate) (PBT) and poly(ethylene naphthalene-2,6-dicarboxylate) (PEN) were pyrolysed in a fixed bed reactor in the presence of calcium hydroxide (Ca(OH)₂) in order to obtain benzene and naphthalene, respectively. In these experiments different ratios of polymer and Ca(OH)₂ were used. Also the temperature was varied in a range between 600 °C and 800 °C. It was found that the highest yield of benzene (67%) was obtained at a temperature of 700 °C and a molar Ca(OH)₂/PBT ratio of 10. The amount of carbon, fixed in the reactor residue after the experiment, was reduced from 56% for pure PBT to 38% under these conditions. Aromatic byproducts were reduced, as well, while the amount of 1,3-butadiene increased. Tetrahydrofuran was just formed under the influence of Ca(OH)₂.For PEN, the optimal conditions were found at a temperature of 600 °C and a molar Ca(OH)₂/PEN ratio of 5. A naphthalene yield of 80% from PEN was obtained. The rise of the naphthalene yield was caused by a more effective decomposition of the polyester by Ca(OH)₂, which led to the reduction of carbon in the reactor residue after the experiment from 59% for pure PEN to 10% under optimised conditions. The part of aromatic byproducts changed just slightly.     

Interval kinetic gravimetric sorption of acetone in random copolymers of poly(ethylene terephthalate) and poly(ethylene 2,6-naphthalate)

Interval sorption kinetics of acetone in solvent cast films of random poly(ethylene terephthalate)-co-(ethylene 2,6-naphthalate) (PET-co-PEN) are reported at 35°C and at acetone pressures ranging from 0 to 7.3 cm Hg. Polymer composition is varied systematically from 0% to 50% poly(ethylene 2,6-naphthalate). Equilibrium sorption is well described by the dual-mode sorption model. Interval sorption kinetics are described using a two-stage model that incorporates both Fickian diffusion and protracted polymer structural relaxation. The incorporation of low levels of PEN into PET significantly reduces the excess free volume associated with the glassy state and, for these interval acetone sorption experiments in ∼ 5 μm-thick films, decreases the fraction of acetone uptake controlled by penetrant-induced polymer structural relaxation. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2973–2984, 1999     

Synthesis,physical characterization,and acetone sorption kinetics in random copolymers of poly(ethylene terephthalate) and poly(ethylene 2,6-naphthalate)

Random copolymers of poly(ethylene terephthalate) (PET) and poly(ethylene 2,6-naphthalate) (PEN) were synthesized by melt condensation. In a series of thin, solvent cast films of varying PEN content, acetone diffusivity and solubility were determined at 35°C and an acetone pressure of 5.4 cm Hg. The kinetics of acetone sorption in the copolymer films are well described by a Fickian model. Both solubility and diffusivity decrease with increasing PEN content. The acetone diffusion coefficient decreases 93% from PET to PET/85PEN, a copolymer in which 85 weight percent of the dimethyl terephthalate in PET has been replace by dimethyl naphthalate 2,6-dicarboxylate. The acetone solubility coefficient in the amorphous regions of the polymer decreases by approximately a factor of two over the same composition range. The glass/rubber transition temperatures of these materials rise monotonically with increasing PEN content. Copolymers containing 20 to 80 wt % PEN are amorphous. Samples with <20% or >80% PEN contain measurable levels of crystallinity. Estimated fractional free volume in the amorphous regions of these samples is lower in the copolymers than in either of the homopolymers. Relative free volume as probed by positron annihilation lifetime spectroscopy (PALS) decreases systematically with increasing PEN content. Acetone diffusion coefficients correlate well with PALS results. Infrared spectroscopy suggests an increase in the fraction of ethylene glycol units in the trans conformation in the amorphous phase as the concentration of PEN in the copolymer increases. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2981–3000, 1998     

Miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) blends by transesterification

The effects of transesterification on the miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) were studied. Blends were obtained by solution precipitation at room temperature to avoid transesterification during blend preparation. The physical blends and transesterified products were analyzed by wide-angle x-ray scattering, differential scanning calorimetry, and nuclear magnetic resonance spectroscopy. It was found that the physical blends are immiscible and when the extent of transesterification reaches 50% of the completely randomized state, independent of blend composition, the blends are not crystallizable and show a single glass transition temperature between those of starting polymers. The interchange reactions were significantly influenced by annealing temperature and time but negligibly by blend composition. © 1996 John Wiley & Sons, Inc.     

Transesterification kinetics of poly(ethylene terephthalate) and poly(ethylene 2,6‐naphthalate) blends with the addition of 2,2′‐bis(1,3‐oxazoline)

The kinetics of the transesterification reaction between poly(ethylene terephthalate) (PET) and poly(ethylene 2,6‐naphthalate) (PEN) with and without the addition of a chain extender were studied with ¹H NMR. Different kinetic approaches were considered, and a second‐order, reversible reaction was accepted for the PET/PEN reactive blend system. The addition of 2,2′‐bis(1,3‐oxazoline) (BOZ) promoted the transesterification reaction between PET and PEN in the molten state. The activation energy of the transesterification reaction for the PET/PEN reactive blend with BOZ (94.0 kJ/mol) was lower than that without BOZ (168.9KJ/mol). The rate constant k took an almost constant value for blend samples with different compositions mixed at 275 °C. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2607–2614, 2001     

Influence of multiwall carbon nanotube on physical properties of poly(ethylene 2,6‐naphthalate) nanocomposites

Polymer nanocomposites consisting of multiwall carbon nanotube (MWCNT) and poly(ethylene 2,6‐naphthalate) (PEN) were prepared by a melt blending process in a twin‐screw extruder. The storage modulus (G′) and loss modulus (G″) of the PEN/MWCNT nanocomposites increased with increasing frequency, and this increment being more significant at low frequency. The terminal zone slope of G′ for the PEN/MWCNT nanocomposites decreased with increasing MWCNT content, and the nonterminal behavior of those was related to the dominant nanotube–nanotube interactions at higher MWCNT content, leading to the formation of the interconnected or network‐like structures of MWCNT in the polymer nanocomposites. The decrease in the slope of the plot of log G′ versus log G″ for the PEN/MWCNT nanocomposites with increasing MWCNT content suggested the changes in the microstructures of the polymer nanocomposites by incorporating MWCNT. The incorporation of very small quantity of MWCNT significantly improved the mechanical properties of the PEN/MWCNT nanocomposites. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1062–1071, 2006     

Effect of aging on fractional crystallization of poly(ethylene oxide) component in poly(ethylene oxide)/poly(3‐hydroxybutyrate) blends

The effect of aging on the fractional crystallization of the poly(ethylene oxide) (PEO) component in the PEO/poly(3‐hydroxybutyrate) (PHB) blend has been investigated. The partial miscibility of the PEO/PHB blends with high PEO molecular weight (M_v = 2.0 × 10⁵ g/mol) was confirmed by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis. The fractional crystallization behavior of the PEO component in the PEO/PHB blends with low PEO content (not more than 30 wt% of PEO), before and after aging under vacuum at 25 °C for 6 months, were compared by DSC, fourier transform infrared microscopic spectroscopy, small angle X‐ray diffraction, and scanning electron microscopy. It was confirmed that nearly all the PEO components remain trapped within interlamellar regions of PHB for the PEO/PHB blends before aging. Under this condition, the crystallization of PEO is basically induced by much less active heterogeneities or homogeneous nucleation at high supercoolings. While, after the same PEO/PHB samples were stored at 25 °C in vacuum for 6 months, a part of the PEO component was expelled from the interlamellar region of PHB. Under this condition, the expelled PEO forms many separate domains with bigger size and crystallizes at low supercoolings by active heterogeneous nucleation, whereas the crystallization of PEO in the interlamellar region is still mainly induced by less active heterogeneities or homogeneous nucleation at extreme supercoolings. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2665–2676, 2005     

Relaxation behavior of poly(ethylene terephthalate)/poly(ethylene naphthalene 2,6‐dicarboxylate) blends prepared by cryogenic blending

A method including cryogenic grinding, melt pressing from the molten state, and quenching was used to prepare blends of poly(ethylene terephthalate) (PET) and poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) in which the two phases were highly dispersed. The effect of melt‐pressing times on the thermal properties and relaxation behavior of PET/PEN films were characterized with differential scanning calorimetry and dielectric spectroscopy. For short melt‐pressing times, two glass‐transition, two crystallization, and two melting peaks were observed, indicating the presence of PET‐rich and PEN‐rich phases in these blends. Longer melt‐pressing times revealed a single glass transition and a single α‐relaxation process, showing that PET–PEN block copolymers were likely to be formed during the melt pressing. The experimental findings were examined in terms of the transesterification reactions between the blend components, as revealed by ¹H NMR measurements. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2570–2578, 2002     

Physical aging of poly(ether sulfone)-modified epoxy resin

The physical aging process of 4,4′-diaminodiphenylsulfone (DDS) cured diglycidyl ether bisphenol-A (DGEBA) blended with poly(ether sulfone) (PES) was studied by differential scanning calorimetry (DSC) at four aging temperatures between T_g-50°C and T_g-10°C. At aging temperatures between T_g-50 and T_g-30°C, the experimental results of epoxy resin blended with 20 wt% of PES showed two enthalpy relaxation processes. One relaxation process was due to the physical aging of PES, the other relaxation process was due to the physical aging of epoxy resin. The distribution of enthalpy relaxation process due to physical aging of epoxy resin in the blend was broader and the characteristic relaxation time shorter than those of pure epoxy resin at the above aging temperatures (between T_g-50 and T_g-30°C). At an aging temperature between T_g-30 and T_g-10°C, only one enthalpy relaxation process was found for the epoxy resin blended with PES, the relaxation process was similar to that of pure epoxy resin. The enthalpy relaxation process due to the physical aging of PES in the epoxy matrix was similar to that of pure PES at aging temperatures between T_g-50 and T_g-10°C. © 1997 John Wiley & Sons, Inc.     

Thermal and mechanical properties of mandelic acid‐copolymerized poly(butylene succinate) and poly(ethylene adipate)

Phenyl side chains were introduced to poly(butylene succinate) and poly(ethylene adipate) by the polymerization of the respective monomers in the presence of mandelic acid. The increasing content of the phenyl side chains decreased the melting temperature and the crystallinity but increased the glass‐transition temperature of the aliphatic polyesters. The phenyl side branches reduced the crystallinity of poly(butylene succinate) more significantly than the ethyl or n‐octyl side branches did. The tensile strength, elongation, and tear strength of poly(ethylene adipate) decreased with an increase in the content of mandelic acid units. However, the increasing content of mandelic acid units enhanced the elongation and tear strength of poly(butylene succinate) considerably without a notable deterioration of tensile strength. The biodegradability of the copolyesters was increased as a result of the introduction of more mandelic acid units due to the decrease in the crystallinity. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1504–1511, 2000     

Lamellar‐level morphology induced by combined crystallization and liquid–liquid demixing in a poly(ethylene terephthalate)/poly(ethylene‐2,6‐naphthalate) blend

The lamellar‐level morphology of an extruded poly(ethylene terephthalate) (PET)/poly(ethylene‐2,6‐naphthalate) (PEN) blend was investigated with small‐angle X‐ray scattering (SAXS). Measurements were made as a function of the annealing time in the melt and the crystallization temperature. The characteristic morphological parameters at the lamellar level were determined by correlation function analysis of the SAXS data. At a low crystallization temperature of 120 °C, the increased amorphous layer thickness was identified in the blend, indicating that some PEN was incorporated into the interlamellar regions of PET during crystallization. The blend also showed a larger lamellar thickness than pure PET. A reason for the increase in the lamellar thickness might be that the formation of thinner lamellar stacks by secondary crystallization was significantly restricted because of the increased glass‐transition temperature. At high crystallization temperatures above 200 °C, the diffusion rates of noncrystallizable components were faster than the growth rates of crystals, with most of the noncrystallizable components escaping from the lamellar stacks. As a result, the blend showed an interfibrillar or interspherulitic morphology. © 2002 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 317–324, 2002     

Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

Clustering of poly(ethylene oxide) in water revisited

The dynamic light scattering results presented in this letter demonstrate that the clustering of poly(ethylene oxide) (PEO) can be observed even in ultrapure, freshly double‐distilled and filtered deionized water. It is confirmed that the filtration of solutions removes the clustering structure and that a steady‐state amount of PEO in clusters is reformed in filtered solutions within 24 h. Adding a drop of chloroform to unfiltered aqueous solutions of PEO temporarily alters the clustering structure, but it prevents the clustering of PEO in filtered solutions. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 135–138, 2003     

Changes in superstructure and mechanical properties of poly(ethylene‐2,6‐naphthalate) fibers with critical necking tension

Poly(ethylene‐2,6‐naphthalate) fibers were zone‐drawn under a critical necking tension (σ_c) defined as the minimum tension needed to generate a necking at a given drawing temperature (T_d). In the zone drawing under σ_c, the neck was observed from 110 to 160 °C. The superstructure in a neck zone induced at each T_d was studied. The σ_c value decreased exponentially with increasing T_d and dropped to a low level at a higher T_d. The draw ratio increased rapidly with T_d increasing above 90 °C, but the birefringence and degree of crystallinity decreased gradually. To study the molecular orientation in the neck zone, we measured a dichroic ratio (A_‖/A_?) of a C? O band at 1256 cm^?1 along a drawing direction in the neck zone with a Fourier transform infrared microscope. A_‖/A_? at T_d = 110 °C increased rapidly in the narrow neck zone, and that at T_d = 140 °C increased in the edge of the wide neck zone. Wide‐angle X‐ray diffraction patterns of the fibers obtained at T_d = 130 °C and lower showed three reflections due to an α form, but those at T_d = 140 and 150 °C had reflections due to the α form and a β form. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1629–1637, 2001     

Physical transitions and crystallization phenomena in poly(ethylene terephthalate) studied by microhardness

The crystallization behavior of poly(ethylene terephthalate) both with and without sodium montanate, a crystal nucleating agent, has been studied using the microhardness technique. The kinetics of crystallization from the glassy state were investigated in real time by measuring the microhardness H at different crystallization temperatures. Results are discussed in terms of the Avrami equation. Values of the Avrami exponent n of about 3 are observed for samples irrespective of nucleating agent. For samples with nucleant two crystallization ranges are observed: a first range which corresponds to a fast crystallization from nucleating agent particles and a second range which is associated with a slow self-crystallization mode. New transitions evidenced by the presence of a small maximum in H as a function of annealing time and temperature are detected at temperatures above T_g for physically aged samples. The kinetics of this transition have also been examined. It is further shown that the presence of nucleating agent induces a hardening at room temperature which is similar to the effect produced by the physical aging of the samples below T_g. Finally, it is found that aging reduces the rate of creep of the material under the indenter. © 1993 John Wiley & Sons, Inc.