Colloidal stability of bare and polymer-grafted silica nanoparticles in ionic liquids

The colloidal stability of bare and poly(methyl methacrylate) (PMMA)-grafted silica nanoparticles was studied in 1-alkyl-3-methylimidazolium ([C(n)mim])-based ionic liquids (ILs) with different anionic structures. The theoretical estimation of the colloidal interaction between monodispersed bare silica particles by using the Derjaguin-Landau-Verwey-Overbeek theory indicates that bare silica particles cannot be stabilized and they rapidly form aggregates in all the ILs used in this study. The instability of bare silica particles was experimentally confirmed by dynamic light scattering measurement and in situ transmission electron microscopy observations by utilizing the negligible vapor pressure of ILs. This evidence suggests that electrostatic stabilization is inefficient in ILs because of the high ionic atmosphere and the resulting surface-charge screening. The PMMA-grafted silica particles exhibited long-term colloidal stability in [C(4)mim][PF(6)] and [C(n)mim][NTf(2)], which are compatible with the grafted PMMA. On the other hand, the PMMA-grafted particles could not be stabilized in [C 4mim][BF 4] due to the poor solubility of the grafted PMMA in the IL. Effective steric stabilization is important for obtaining stable colloidal particles in ILs.     

Influence of the nature of organic groups on the properties of organically modified silica aerogels

Organically modified aerogels were prepared by NH₄OH-catalyzed hydrolysis and condensation of RSi(OMe)₃ (R = Me, Pr ⁿ , Ph, Bu ⁱ )/Si(OMe)₄ or (MeO)₃Si-Y-Si(OMe)₃/Si(OMe)₄ (Y = C₂H₄, p-C₆H₄, C₆H₁₂) mixtures, followed by supercritical drying of the alcogels with methanol. Starting from 1:4 mixtures of RSi(OMe)₃ and Si(OMe)₄, hydrophobic aerogels with nearly no residual Si-OH or Si-OMe groups were obtained. These aerogels were therefore insensitive towards moisture. Their elastic constant was distinctly lower than that of unmodified silica aerogels. Aerogels similarly prepared from 1:8 mixtures of (MeO)₃Si-Y-Si(OMe)₃ and Si(OMe)₄ had a rather high concentration of residual Si-OMe groups, and therefore they were hydrophilic. Their elasticity was about the same as that of unmodified silica aerogels. The difference between the two types of aerogels suggests different microstructures, depending on the nature of the organic groups.     

Effective grafting of polymers onto ultrafine silica surface: Photopolymerization of vinyl monomers initiated by the system consisting of trichloroacetyl groups on the surface and Mn2(CO)10

The effective grafting of vinyl polymers onto an ultrafine silica surface was successfully achieved by the photopolymerization of vinyl monomers initiated by the system consisting of trichloroacetyl groups on the surface with Mn₂(CO)₁₀ under UV irradiation at 25 °C. The introduction of trichloroacetyl groups onto the surface of silica was achieved by the reaction of trichloroacetyl isocyanate with surface amino groups, which were introduced by the treatment of silica with 3‐aminopropyltriethoxysilane. During the polymerization, the corresponding polymers were effectively grafted onto the surface, based on the propagation of polymer from surface radicals formed by the interaction of trichloroacetyl groups and Mn₂(CO)₁₀. The percentage of poly(methyl methacrylate) grafting onto the silica reached 714.6% after 90 min. The grafting efficiency (proportion of grafted polymer to total polymer formed) in the polymerization of methyl methacrylate was very high, about 80%, indicating the depression of formation of ungrafted polymer. Polymer‐grafted silica gave a stable colloidal dispersion in good solvents for grafted polymer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2157–2163, 2001     

Dispersion polymerization of MMA in supercritical CO2 stabilized by random copolymers of 1H,1H–perfluorooctyl methacrylate and 2‐(dimethylaminoethyl methacrylate)

A series of random copolymers, composed of 1H,1H‐perfluorooctyl methacrylate (FOMA) and 2‐dimethylaminoethyl methacrylate (DMAEMA) were prepared as stabilizers for the dispersion polymerization of methyl methacrylate in supercritical CO₂ (scCO₂). Free‐flowing, spherical poly(methyl methacrylate) (PMMA) particles were produced in high yield by the effective stabilization of poly(FOMA‐co‐DMAEMA) containing 34–67 w/w % (15–41 m/m %) FOMA structural units. Less stabilized but micron‐sized discrete particles could be obtained even with 25 w/w % (10 m/m %) FOMA stabilizer. The result showed that the composition of copolymeric stabilizers had a dramatic effect on the size and morphology of PMMA. The particle size was controllable with the surfactant concentration. The effect of the monomer concentration and the initial pressure on the polymerization was also investigated. The dry polymer powder obtained from dispersion polymerization could be redispersed to form stable aqueous latexes in an acidic buffered solution (pH = 2.1) by an electrostatic stabilization mechanism due to the ionization of DMAEMA units in the stabilizer. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1365–1375, 2008     

Silica nanoparticle covered with mixed polymer brushes as Janus particles at water/oil interface

Silica nanoparticles (NSiO₂) are modified with mixed polymer brushes derived from a block copolymer precursor, poly(methyl methacrylate)-b-poly(glycidyl methacrylate)-b-poly(tert-butyl methacrylate) with short middle segment of PGMA, through one step ??grafting-onto?? approach. The block polymer precursors are prepared via reversible addition?Cfragmentation chain transfer-based polymerization of methyl methacrylate, glycidyl methacrylate, and tert-butyl methacrylate. The grafting is achieved by the reaction of epoxy group in short PGMA segment with silanol functionality of silica. After hydrolysis of poly(tert-butyl methacrylate) segment, amphiphilic NSiO₂ with ??V-shaped?? polymer brushes possessing exact 1:1 molar ratio of different arms were prepared. The functionalized particles self-assemble at oil/water interfaces to form stable large droplets with average diameter ranging from 0.15?±?0.06 to 2.6?±?0.75?mm. The amphiphilicity of the particles can be finely tuned by changing the relative lengths of poly(methyl methacrylate) and poly(methacrylic acid) segments, resulting in different assembly behavior. The method may serve as a general way to control the surface property of the particles.     

Surface functionalization of silica nanoparticles supports colloidal stability in physiological media and facilitates internalization in cells

The influence of the surface functionalization of silica particles on their colloidal stability in physiological media is studied and correlated with their uptake in cells. The surface of 55 ± 2 nm diameter silica particles is functionalized by amino acids or amino- or poly(ethylene glycol) (PEG)-terminated alkoxysilanes to adjust the zeta potential from highly negative to positive values in ethanol. A transfer of the particles into water, physiological buffers, and cell culture media reduces the absolute value of the zeta potential and changes the colloidal stability. Particles stabilized by L-arginine, L-lysine, and amino silanes with short alkyl chains are only moderately stable in water and partially in PBS or TRIS buffer, but aggregate in cell culture media. Nonfunctionalized, N-(6-aminohexyl)-3-aminopropyltrimethoxy silane (AHAPS), and PEG-functionalized particles are stable in all media under study. The high colloidal stability of positively charged AHAPS-functionalized particles scales with the ionic strength of the media, indicating a mainly electrostatical stabilization. PEG-functionalized particles show, independently from the ionic strength, no or only minor aggregation due to additional steric stabilization. AHAPS stabilized particles are readily taken up by HeLa cells, likely as the positive zeta potential enhances the association with the negatively charged cell membrane. Positively charged particles stabilized by short alkyl chain aminosilanes adsorb on the cell membrane, but are weakly taken up, since aggregation inhibits their transport. Nonfunctionalized particles are barely taken up and PEG-stabilized particles are not taken up at all into HeLa cells, despite their high colloidal stability. The results indicate that a high colloidal stability of nanoparticles combined with an initial charge-driven adsorption on the cell membrane is essential for efficient cellular uptake.     

Synthesis of Macroporous PMMA/Silica Nanocomposite Monoliths in Supercritical Carbon Dioxide

Summary: Macroporous monoliths consisting of silica nanoparticles embedded in poly(methyl methacrylate) (PMMA) were synthesized in supercritical CO₂. Well‐dispersed silica particles, pretreated with functional 3‐(trimethoxysilyl)propyl methacrylate (MPS), were to form colloidal PMMA nanocomposites followed by a sol‐gel transition forming interconnected structures resulting in micron‐sized pores with specific areas between 1 and 7 m² · g⁻¹. SEM and TEM results revealed uniform morphological characteristics of the composite materials and good dispersions of the silica nanoparticles.

SEM micrograph of PMMA/Silica nanocomposites forming interconnected macroporous monolith. The average size of the silica particles is 50 nm.     

Colloidal crystallization of colloidal silica modified with ferrocenyl group-contained polymers in organic solvents

Surface modification of colloidal silica with ferrocenyl-grafted polymer and colloidal crystallization of the particles in organic solvent were studied. Poly(methyl methacrylate-co-vinylferrocene)-grafted silica never formed colloidal crystals in polar solvent, such as acetone, acetonitrile, ethanol and N,N-dimethylformamide (DMF), while poly(methyl methacrylate-co-ferrocenyl acrylate)-grafted silica gave colloidal crystallization in DMF. The particles prepared by grafting of poly(N,N-dimethylacrylamide-co-vinylferrocene), with vinylferrocene (Vfc) mole fraction of 1/13 and 1/23, were observed to give the crystallization in ethanol and DMF over particle volume fraction of 0.058. Further, silica modified with copolymer of Vfc and N-vinyl-2-pyrrolidone, N-vinylcarbazole or N-isopropylacrylamide formed colloidal crystals in ethanol and DMF. Especially, poly(N-isopropylacrylamide-co-Vfc)-grafted silica, which was composed of the highest mole fraction of vinylferrocene, 1/3, afforded colloidal crystallization in ethanol over particle volume fraction of 0.053. Relatively high polar vinylferrocene copolymer grafting of silica resulted in colloidal polymerization in organic solvents.     

Stepwise controlled immobilization of colloidal crystals formed by polymer-grafted silica particles

Colloidal crystals formed by polymer-grafted silica particles were immobilized by a stepwise procedure consisting of gelation by radical copolymerization followed by solidification by ring-opening radical polymerization. In the first step, the poly(methyl methacrylate) (PMMA)-grafted silica colloidal crystal suspension was incorporated into the gel without altering the crystal structure by copolymerization of cross-linker, 1,2-dimethylacryloyloxyethane (DME) and methyl methacrylate (MMA). In the second step, ring-opening radical polymerization was performed after substituting the solvent with vinylidene-1,3-dioxolane. By this two-step procedure, the silica particle array of colloidal crystals was immobilized and made into durable material.     

Composite Particles From Pickering‐Stabilized Radical Mediated Thiol‐Ene Suspension Polymerizations

Pickering stabilization is a facile method to create composite colloidal particles. Inorganic colloidal SiO₂ nanoparticles are often used as the stabilizer for particles instead of the more common amphiphilic surfactants. Here the use of this approach in radical‐mediated thiol‐ene suspension polymerizations using monomers 1,3,5‐triallyl‐1,3,5‐triazine‐2,4,6(1H,3H,5H)‐trione (TTT) and pentaerythritol tetrakis (3‐mercaptopropionate) (PETMP) is described. The resulting micron‐sized crosslinked poly(thioether) colloidal particles are coated with 80 nm silica nanoparticles. The addition of a small amount of various costabilizers is examined (hexadecane, cetyl alcohol and toluene), and while all yielded particles, cetyl alcohol provide more consistent results. Scanning electron microscopy and thermal analysis of the composite particles demonstrate morphologies that are consistent with a raspberry‐like structure. No significant changes to the glass transition temperature are observed, which is consistent with the silica nanoparticles being located at the surface of the polymer particles.     

Kinetics analysis of colloidal crystallization of silica spheres modified with polymers on their surfaces in acetonitrile

 The nucleation and growth rates in the colloidal crystallization of silica spheres (136 nm in diameter) modified with polymers on their surface were measured by time-resolved reflection spectroscopy. The polymers were poly(maleic anhydride-co-styrene) [P(MA-ST)] and poly(methyl methacrylate) (PMMA). The induction period for nucleation decreased sharply when the sphere concentration increased. The crystal growth process consisted of a fast growing step leading to metastable crystals (rate v ₁) and a slow growth rate accompanied by the formation of stable crystals. The crystal size of the P(MA-ST)/SiO₂ particles decreased from 0.4 to 0.06 mm, whereas v ₁ increased from 13 to 37 μm/s, when the particle concentration increased. The slow step was also observed for almost all the samples but was not analyzed since the rate was too small. For PMMA/SiO₂ dispersions, the crystal size (0.17–0.3 mm) and v ₁ (43–166 μm/s) did not show any relation to the particle concentration but showed a linear relationship with the molecular weight of PMMA. These results suggest the important role of the excluded-volume effects of the polymer layers around the silica surface. The contribution of the repulsion due to the electrical double layers is still effective in the colloidal crystallization in acetonitrile. Received: 6 June 2001 Accepted: 20 September 2001     

Rigidity of colloidal crystals of silica spheres modified with polymers on their surfaces in organic solvents

Rigidity (G) of colloidal crystals in organic solvents of acetonitrile and nitrobenzene has been measured by reflection spectroscopy in sedimentation equilibrium. The colloidal spheres used are the silica spheres (136 nm in diameter) modified on their surfaces with polymers, poly(maleic anhydride-co-styrene) [P(MA-ST)], poly(methyl methacrylate) (PMMA), or polystyrene (PST). Log G increases linearly with the slope of unity as log N (number density of colloidal spheres) increases. The mean values of the b-factor, which is the fluctuation parameter in crystal lattices and should be smaller than 0.1 according to the Lindeman's rule, are 0.045±0.003, 0.039±0.007, and 0.038±0.003 for P(MA-ST)/SiO₂, PMMA/SiO₂, and PST/SiO₂, respectively. These values are larger than that of colloidal crystals of mother silica spheres in the deionized aqueous suspension, 0.028. These results support the important role of the excluded volume effects from the polymer layers formed around the silica surfaces. However, contribution of the excluded volume effects from the electrical double layers formed around the spheres in the organic solvents is also effective in the colloidal crystallization. Electronic Publication     

Preparation of poly(methyl methacrylate)/CaCO3/SiO2 composite particles via emulsion polymerization

A novel method to prepare organic/inorganic composite particles, i.e. poly(methyl methacrylate)/CaCO₃/SiO₂ three-component composite particles, using emulsion polymerization of methyl methacrylate with sodium lauryl sulfate as a surfactant in an aqueous medium was reported. CaCO₃/SiO₂ two-component inorganic composite particles were obtained firstly by the reaction between Na₂CO₃ and CaCl₂ in porous silica (submicrometer size) aqueous sol and the specific surface area of the particles was measured by the Brunauer–Emmett–Teller (BET) method. The results show that the BET specific surface area of the CaCO₃/SiO₂ composite particle is much smaller than that of the silica particle, indicating that CaCO₃ particles were adsorbed by porous silica and that two-component inorganic composite particles were formed. Before copolymerization with methyl methacrylate, the inorganic composite particles were coated with a modifying agent through covalent attachment. The chemical structures of the poly(methyl methacrylate)/CaCO₃/SiO₂ composite particles obtained were characterized by Fourier transform IR spectroscopy and thermogravimetric analysis. The results show that the surface of the modified inorganic particles is grafted by the methyl methacrylate molecules and that the grafting percentage is about 15.2%.     

Establishing the difference between colloidal borosilicate and boron-modified colloidal silica via chelation of boron with catechol and dl-tartaric acid

Colloidal borosilicate and boron-modified colloidal silica sols were studied by ¹¹B NMR. Formation of B–O–Si chemical bonds is established in both materials. It is shown that boron present in colloidal borosilicate is stable towards the action of complexing agents catechol and tartaric acid. In contrast, the boron in boron-modified silica is readily complexed by these agents. The results presented herein demonstrate that B–O–Si bonds are homogeneously distributed throughout the colloidal borosilicate disperse phase, while in boron-modified colloidal silica they are concentrated at the surface of colloidal silica particles.     

Synthesis of vinyl polymer-silica colloidal nanocomposites prepared using commercial alcoholic silica sols

The surfactant-free synthesis of vinyl polymer-silica nanocomposite particles has been achieved in aqueous alcoholic media at ambient temperature in the absence of auxiliary comonomers. Styrene, methyl methacrylate, methyl acrylate, n-butyl acrylate, and 2-hydroxypropyl methacrylate were homopolymerized in turn in the presence of three commercially available ultrafine alcoholic silica sols. Stable colloidal dispersions with reasonably narrow size distributions were obtained, with silica contents of up to 58% by mass indicated by thermogravimetric analysis. Particle size distributions were assessed using both dynamic light scattering and disk centrifuge photosedimentometry. The former technique indicated that the particle size increased for the first 1-2 h at 25 degrees C and thereafter remained constant. Particle morphologies were studied using electron microscopy. Most of the colloidal nanocomposites comprised approximately spherical particles with relatively narrow size distributions, but in some cases more polydisperse or nonspherical particles were obtained. Selected acrylate-based nanocomposites were examined in terms of their film formation behavior. Scanning electron microscopy studies indicated relatively smooth films were obtained on drying at 20 degrees C, with complete loss of the original particle morphology. The optical clarity of solution-cast 10 microm nanocomposite films was assessed using visible absorption spectrophotometry, with 93-98% transmission being obtained from 400 to 800 nm; the effect of long-term immersion of such films in aqueous solutions was also examined. X-ray photoelectron spectroscopy studies indicated that the surface compositions of these nanocomposite particles are invariably silica-rich, which is consistent with their long-term colloidal stability and also with aqueous electrophoresis measurements. FT-IR studies suggested that in the case of the poly(methyl methacrylate)-silica nanocomposite particles, the carbonyl ester groups in the polymer are hydrogen-bonded to the surface silanol groups. According to differential scanning calorimetry studies, the glass transition temperatures of several poly(methyl methacrylate)-silica and polystyrene-silica nanocomposites can be either higher or lower than those of the corresponding homopolymers, depending on the nature of the silica sol.     

Effects of particle volume fraction on distortion of particle-arrayed structure during immobilization of colloidal crystals formed by poly(methyl methacrylate)-grafted silica in acetonitrile

Changes of particle array structure with particle volume fraction during immobilization of colloidal crystals, formed by poly(methyl methacrylate)-grafted silica in acetonitrile, were investigated. Immobilization of colloidal crystals formed in acetonitrile was carried out by two-step photo-radical copolymerization of methyl methacrylate and ethylene dimethacrylate to make organogel, followed by solidification after exchanging the solvent with methyl methacrylate. Crystallite size in colloidal crystals formed in acetonitrile was mostly unchanged with particle volume fraction in the range of 0.11–0.18, while the size and number of single crystals decreased during gelation. Disordering in particle array in immobilized colloidal crystals in gel and poly(methyl methacrylate) matrix was observed to decrease with increasing particle volume fraction less than 0.18 due to strong electrostatic repulsion between particles.     

Biomimetic deposition of silica templated by a cationic polyamine-containing microgel

We report using poly(acrylamide-co-2-(dimethylamino)ethyl methacrylate, methyl chloride quaternized) cationic microgels as a porous colloidal template for biomimetic in situ silica mineralization, allowing the well-controlled synthesis of submicrometer-sized hybrid microgel--silica particles and porous silica particles by subsequent calcination. The microgels were prepared by inverse emulsion polymerization in the presence of a bisacrylamide cross-linker. Silica deposition was achieved by simply stirring an aqueous mixture of the microgel particles and tetramethyl orthosilicate (TMOS) at 20 degrees C for 30 min. No experimental evidence was found for nontemplated silica, which indicated that silica deposition occurred exclusively within the cationic microgel template particles. The resulting microgel-silica hybrid particles were characterized by electron microscopy, dynamic light scattering, FT-IR spectroscopy, 1H NMR and solid-state 29Si magic angle spinning NMR spectroscopy, thermogravimetry, aqueous electrophoresis, and surface area measurements. Aqueous electrophoresis studies confirmed that the hybrid microgel-silica particles had positive zeta potentials over a wide pH range and isoelectric points could be tuned by varying the synthesis conditions. This suggests that these particles could form complexes with DNA for improved gene delivery. The porosity of the calcined silica particles could be controlled by varying the amount of TMOS, suggesting potential encapsulation/controlled release applications.     

Synthesis of propylene glycol methyl ether over amine modified porous silica

Amine functionalized silica catalysts (3-aminopropyltrimethoxysilane (APTMS)) NH₂/SiO₂, (Diazabicycloundecene/SiO₂) DBU/SiO₂ and (1,5,7-triazabicyclo[4,4,0]dec-5-ene/SiO₂) TBD/SiO₂, which were characterized by ²⁹Si NMR, element analysis and indicator dye adsorption, were prepared by ultrasonic technique under mild conditions. Such hybrid solid bases showed high catalytic activity and good reusability towards for the synthesis of propylene glycol methyl ether.     

Highly transparent silica monoliths embedded with high concentration oxide nanoparticles

Silica monoliths embedded with high concentration of γ-Fe₂O₃ or TiO₂ nanoparticles were prepared by a sol–gel procedure designed according to the inherent properties of oxide colloids. In the first step, highly dispersible oxide nanoparticles were produced using an in situ modification sol–gel strategy. Then, these particles were re-dispersed in silicon alkoxide-containing solution to form a stable colloidal solution. The hydrolysis and condensation reactions of alkoxide were catalyzed by an organic base (morpholine). Due to the large molecule size of morpholine, the electric double layer on the surface of colloidal particles was not compressed by the ionized morpholine molecules. The colloidal solution thus remained stable during the gelation process. Through this procedure, oxide nanoparticles could be immobilized homogeneously in the pores of a silica matrix, forming highly transparent and crack-free monoliths.     

Surface ATRP of hydrophilic monomers from ultrafine aqueous silica sols using anionic polyelectrolytic macroinitiators

A convenient two-step route was developed to prepare new anionic ATRP macroinitiators from near-monodisperse poly(2-hydroxyethyl methacrylate) precursors by partial esterification with 2-bromoisobutyryl bromide, followed by esterification of the remaining hydroxyl groups using excess 2-sulfobenzoic acid cyclic anhydride. These new macroinitiators can be electrostatically adsorbed onto ultrafine cationic Ludox CL silica sols; subsequent surface polymerization of various hydrophilic monomers in aqueous solution at room temperature afforded a range of polymer-grafted ultrafine silica sols. The resulting sterically stabilized particles were characterized by dynamic light scattering, transmission electron microscopy, aqueous electrophoresis, FTIR spectroscopy, and elemental microanalyses.