Synthesis and characterization of surface-cyanofunctionalized poly (N-isopropylacrylamide) latexes

 A series of P[N-isopropylacrylamide (NIPAM)] latexes with different contents of cyano groups were successfully prepared by either seeded or shot-growth polymerizations of an aqueous solution containing acrylonitrile (AN) onto a seed P[NIPAM] latex, respectively, and further characterized by FT-IR, ¹H-NMR, elemental analysis, as well as by quasielastic light scattering (QELS) and scanning electron microscopy (SEM). All prepared surface-cyanofunctionalized P[NIPAM] latexes exhibited the same range of lower critical solution temperature (LCST) as a pure P[NIPAM] latex. The shot polymerization process proved more efficient at yielding cyano derivatized latexes than the seeded polymerization technique. The amount of incorporated cyano groups onto the particles was determined with a good correlation both by ¹H-NMR and elemental analysis. The higher the amount of initially introduced AN monomer in the reaction mixture, the more cyano groups were incorporated onto the particles. The surface of the particles with high content of cyano groups appeared quite rough by SEM in comparison with that of the pure P[NIPAM] particles. Received: 25 February 1998 Accepted: 23 June 1998     

Preparation and characterization of poly (N-isopropylacrylamide-co-dimethylaminoethyl methacrylate) microgel latexes

Monodisperse cationic thermosensitive latex microgels have been prepared by radical-initiated precipitation polymerization of N-isopropylacrylamide, methylene bisacrylamide using 2,2′-azobis(2-amidinopropane hydrochloride) as an initiator and dimethylaminoethyl methacrylate (DMAEMA) as a cationic monomer. The final microgel latexes were characterized with respect to water-soluble polymer formation, particle size and size distribution. Adding cationic monomer (DMAEMA) was found to drastically affect the particle size, but not the size distribution as observed both by transmission electron microscopy and quasielastic light scattering (QELS). However, too high a DMAEMA concentration in the feed composition led to enhanced formation of water-soluble polymer. The volume phase-transition temperature of cleaned microgels examined by QELS (particle size versus temperature) was found to be around 32 °C and was slightly dependent on the concentration of the cationic monomer. The volume phase-transition temperature range becomes broader with increasing cationic monomer concentration. In addition, the pH of the polymerization medium was found to affect the final particle size and amount of water-soluble polymer formed. Received: 29 March 2001 Accepted: 2 July 2001     

Preparation of poly(N-isopropylmethacrylamide) latexes kinetic studies and characterization

Thermosensitive crosslinked polymer latexes have been synthesized by precipitation polymerization of N-isopropylmethacrylamide (NIPMAM) as a main monomer, methylene bis-acrylamide (MBA) as a crosslinker, and potassium persulfate (KPS) as the initiator. Polymerizations kinetics were first investigated by studying both the influence of crosslinker (MBA) and initiator (KPS) concentrations and temperature effects on the polymerization conversion, the particle size, and water-soluble polymer (WSP) as a function of time. Particle size analysis by Scanning Electron Microscopy (SEM) showed that a short nucleation step afforded the synthesis of highly monodispersed latexes. In addition, a strong dependence of WSP formation on MBA and KPS concentration and polymerization temperature was found, as well. Comparison of particle size by SEM and quasielastic light scattering clearly evidenced the dramatic effect of temperature on particle size. Lower critical solubility temperatures (LCST) of latexes were determined and compared. Finally, based on these results, the mechanism of particle formation in this polymerization process is discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1823–1837, 1999     

Study of poly(St/BA/MAA) copolymer latexes with trimodal particle size distribution

A new strategy was developed for producing a polymer latex with trimodal particle size distribution by adding a second seed of polymer particles and some additional surfactants during polymerization. The polymerization was investigated by following the variation of the particle size, the size distribution, the number of particles, the surface tension and surfactant surface coverage at different stages of the polymerization process. The results showed that both the size and the size distribution can be easily controlled by varying the amount of additional surfactants and the second seed of polymer particles. The secondary nucleation was achieved when the surface coverage of particles was over 70%, and the amount of small particles formed increased with increasing amount of additional surfactants. The introduction of the additional surfactants had no significant effect on the size and number of middle particles, but reduced the size of large particles and caused the number of large particles to remain more stable because of the suppression of limited flocculation. Copyright © 1998 John Wiley & Sons, Ltd.     

Synthesis of crosslinked poly(styrene-co-sodium styrenesulfonate) latexes

Latexes of 100 nm diameter were synthesized by emulsifier-free copolymerization of styrene, sodium styrenesulfonate, and 1–5 wt% divinylbenzene using persulfate initiator at 91°C. A shot growth method was used to incorporate a high density of sulfonate groups. Coefficients of variation of particle size were 0.04–0.08 without resort to seed growth polymerization. Redox initiation at 40–50°C produced larger, more polydisperse, and less colloidally stable crosslinked latexes. © 1994 John Wiley & Sons, Inc.     

Preaparation of cationic latexes of poly(styrene-CO-butyl acrylate) and their properties evolution in latex dilution

Cationic latexes were prepared through emulsion copolymerization of styrene(St) and butyl acrylate(BA) with a cationic surfactant,cetyl trimethyl ammonium bromide(CTAB).Latex properties,including particle size,size distribution,ζpotential,surface tension and monomer conversion,were determined for latexes prepared with different CTAB amounts. Evolution of these properties during emulsion polymerization was followed in order to understand the mechanism of the particles formation.Results showed that both particle size andζpotential were function of polymerization time and latex solids.Parallel emulsion polymerizations with cationic,anionic charged initiator and charge-free initiators were also carried out,the latex properties were determined at different polymerization time.All these results were attentively interpreted based on the mechanisms of emulsion polymerization,surfactant adsorption and latex particle stabilization.     

Synthesis and characterization of poly (2-vinylpridine)-b-poly (t-butyl methacrylate)

The synthesis of well defined and monodisperse (M_w/M_n ≤ 1.2) narrow molecular weight distribution poly (2-vinylpyridine)-poly (t-butyl methacrylate) (P2VP-PTBMA) AB block copolymers is carried out by initiation of 2-vinylpyridine polymerization by 1,1-diphenylhexyllithium in THF at-78°C, followed by addition of TBMA and termination at ?78°C using MeOH. The formation of the BAB block copolymer is carried out in a similar fashion except that 1,4-dilithio-1,1,4,4-tetraphenylbutane is used as initiator. The corresponding synthesis of P2VP-PMMA block copolymers is carried in a similar manner, except that 1-2 equivalents of TBMA is used to end-functionalize the living P2VP before the addition of MMA. Without the addition of TBMA, trimodal molecular weight distributions in P2VP-b-PMMA are obtained. All the block copolymers are characterized by Size Exclusion Chromatography (SEC), Nuclear Magnetic Resonance (NMR), and Differential Scanning Calorimetry (DSC). © 1994 John Wiley & Sons, Inc.     

Confocal microscopy studies of shear‐induced coalescence in blends of poly(butyl methacrylate) and poly(2‐ethylhexyl methacrylate)

This article reports the results of confocal fluorescence microscopy studies of shear‐induced coalescence in binary blends of poly(2‐ethylhexyl methacrylate) (PEHMA; 90 wt %) and poly(butyl methacrylate) (PBMA; 10 wt %). We prepared the blends by casting a mixture of latex dispersions of the components onto a substrate and allowing the film to dry under ambient conditions. The initial morphology of the film was a dispersion of 120‐nm PBMA spheres in a continuous PEHMA matrix. One‐fifth of the PBMA particles were labeled with anthracene, the emission of which we observed with confocal microscopy. The blends were sheared in a parallel‐plate rheometer at 80 and 100 °C for 1 and 10 h. Careful image analysis allowed us to estimate the mean size of the dispersed phase and the width of the size distribution. The results were compared with the theoretical limits of Wu and Taylor. After 10 h of shearing, the mean particle size decreased and the particle distribution became narrower in comparison with the results obtained after 1 h of shearing. We explain this result by inferring that before the sample reached steady‐state morphology, its rate of coalescence was greater than the rate of particle breakup. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2317–2332, 2001     

Protein co-adsorption on different polystyrene latexes: Electrokinetic characterization and colloidal stability

 The latex agglutination immunoassay technique uses polymer colloids as a carrier for the adsorbed proteins to enhance the antigen–antibody reaction. Competitive co-adsorption of IgGaCRP and m-BSA proteins on polystyrene latexes with different functionality (sulfate and sulfonate groups) was carried out looking for the increase in the immunoreactivity and colloid stability of latex–protein complexes. The preferential adsorption of a protein is also studied, comparing both surface types. Regarding the application in the development of a diagnostic test system, it is necessary to study the latex–protein complexes from an electrokinetic and colloid stability point of view. The presence of protein on the surface latex shifts the iso-electric point (i.e.p.) of the latex–protein complexes to pH values near the i.e.p. of the protein which is the majority. Thus by the adsorption of m-BSA we can obtain complexes with the i.e.p. near pH 5 and, therefore, with a significant electrostatic repulsion at neutral pH. Due to the higher surface charge density of the sulfonate latexes there is a higher adsorption of both proteins, which can provide a better colloidal stability (by the adsorption of m-BSA) and a better immunoreactivity (by the adsorption of IgG). Received: 27 March 1996 Accepted: 1 September 1996     

Crystalline and spectroscopic characterization of poly(2-aminoethyl methacrylate hydrochloride) chains grafted onto poly[(R)-3-hydroxybutyric acid]

The present study is aimed to investigate the degree of crystallinity of poly(3-hydroxybutyrate) P(3HB) grafted with poly(2-aminoethyl methacrylate hydrochloride) (PAEMA) chains using WAXS, micro Raman, and FTIR spectroscopy. The samples were obtained by radiation induced graft polymerization of the monomer in the substrate using different solvents for comparison. The results of crystallinity are consistent with those obtained of lower crystallinity in grafting copolymer relative to the substrate P(3HB). The low crystallinity is directly related to the increase of the degree of grafting, meaning that although the P(3HB) amorphous region is grafted, the crystalline zone is also affected in some extent by the grafting process and the environment of the new molecule. Three different methods were surveyed to determine the variation of crystallinity degree with the grafting degree. It is shown that all methods provide linear relationships between these variables, but WAXS method was found more acceptable than the others (FTIR and Raman). A detailed characterization of the vibrational bands characteristic of amorphous and helical crystalline structure of the grafting copolymers are also highlighted.     

Oxidations of alkenes catalyzed by a Mn(III) porphyrin and cationic polymer latexes

Three types of cationic polymer latexes were prepared by emulsion copolymerization of vinylbenzyl chloride, divinylbenzene and a third monomer, vinyl octadecyl ether, styrene, or n-decyl methacrylate, followed by quaternization with trimethylamine. The latexes had 44–71 nm diam and polydispersity indices of 1.06–1.10. Vinyl octadecyl ether did not copolymerize but hydrolyzed under the polymerization conditions to produce 1-octadecanol, which as a coemulsifier gave highly viscous latexes. The tetraanion 5,10,15,20-tetrakis-(2,6-dichloro-3-sulfonatophenyl) porphinatomanganese (III) chloride bound irreversibly to the cationic latexes and was an active catalyst for oxidations of alkenes by sodium hypochlorite and potassium peroxymonosulfate in the absence of added organic solvent. The porphyrin catalyst in the latexes was more active than in solution. Porphyrin catalysis gave epoxides concurrently with competing uncatalyzed hypochlorous acid oxidations to complex mixtures of allylic chlorides, allylic alcohols, α,β-unsaturated ketones, and chlorohydrins.     

Preparation and characterization of poly(m-xylylene oxamide) and its copolymer

New polyoxamides, poly(m-xylylene oxamide) (PMXD2) and its copolymer with 2-methyl-1,5- pentanediamine (P(MXD2/M52)) with relative viscosity up to 4.6 were synthesized via spray/solid state polymerization. The obtained polyoxamides were characterized by FTIR, NMR, WAXD, DSC and TGA. The T_m of the copolymers decreased with increasing percentage of poly(2-methyl-1,5- pentaneoxamide) (PM52) in the copolymer from 346°C for 100% poly(meta-xylyleneoxamide) (PMXD2) to 277°C for copolymers of PMXD/PM52 (60/40). TGA analysis revealed that the thermal stability of the copolymers compared well with commercial PA6 and XRD studies suggested the copolymers possessed high crystallinity. DMA profile of the PMXD/PM52 (70/30) copolymer showed better mechanical performance with a storage modulus of about 7.2 GPa as compared to 1.8 GPa of PA6 at 25°C.     

Preparation and characterization of conducting poly(acryloyl chloride)‐g‐ polypyrrole copolymer

The electroactive copolymer of poly(acryloyl chloride) (PAC) and polypyrrole (PPy) can be synthesized by electrochemical polymerization using a polymer precursor which contains a pyrrole moiety in its side chain. Poly(acryloyl pyrrole) (PAP) was synthesized chemically with acryloyl chloride and potassium pyrrole salt and characterized using FT‐IR and ¹H‐NMR spectroscopy. PAP dissolved in dimethyl formamide (DMF), was spin‐coated on a platinum electrode and polymerized electrochemically in the electrolytic mixture solution consisting of acetonitrile, 0.1 M pyrrole, and 0.1 M lithium perchlorate. Constant potential electrolysis showed that pyrrole groups in the precursor were oxidized to form PPy, that is, they acted as grafting centers at which the PPy grew. Scanning electron microscopy (SEM) results and conductivity measurements supported the formation of the graft copolymer. The morphological feature of PAC‐g‐PPy copolymer films showed homogeneous structure, but that of PAC/PPy composite films showed irregular structure. The maximum conductivity of the final products was about 1 S/cm. Copyright © 2002 John Wiley & Sons, Ltd.     

Preparation and characterization of carboxylic-containing poly(methyl methacrylate) nanolatexes

Poly(methyl methacrylate) (PMMA)-based latex particles bearing carboxylic groups at the surface were prepared via emulsion polymerization. The polymerization recipe and process were optimized in order to target monodisperse particles with diameters around 100 nm. The polymerizations were performed using 4,4-azobis(4-cyanopentanoic) acid (ACPA) as initiator and sodium dodecyl sulphate (SDS) as surfactant. The polymerization conversion was determined by both gas chromatography and gravimetry. The final latexes were characterized with respect to particle size, size distribution, surface charge density, electrokinetic properties (i.e. electrophoretic mobility vs pH and ionic strength) and colloidal stability (i.e. coagulation rate constants vs pH and stability factor vs ionic strength).     

聚N-异丙基丙烯酰胺硅胶键合固定相的制备与评价

以3-巯丙基三甲氧基硅烷为偶联剂,将聚N-异丙基丙烯酰胺(PNIPAM)键合到硅胶上,制得了键合固定相（SI-PNIPAM）填料,并用元素分析、红外光谱等对其进行了表征。以甲醇-水为二元流动相,用多环芳烃、碱性物质对该固定相进行了色谱评价,并考察了该固定相的适用pH范围及水解稳定性。结果表明:该固定相具有较好的色谱性能与温敏特性,并且在pH 2.5～7.5时稳定性良好。     

Thermal degradation of poly(ethyl methacrylate) and its copolymer with poly(ethyl acrylate)

The thermal degradation behaviour of poly(ethyl methacrylate) homopolymers and poly(ethyl methacrylate) and poly(ethyl acrylate) copolymers synthesized by using the benzoyl peroxide-di-methyl aniline redox pair at different temperatures (18–35C) was investigated. Contrary to some reports in the literature, the thermal degradation of PEMA was observed to take place in multi steps. These are assigned to be loss of labile end groups, side chain scission, anhydride formation and main chain degradation steps. Dominating chemical formations at the end of these steps were characterized by FTIR spectroscopy.The homopolymer samples synthesized at 18C showed a greater thermal stability against degradation. Copolymerization with small amounts of ethyl acrylate was observed to impart thermal stability to PEMA by stabilizing mainly the end groups against degradations.     

Preparation and characterization of antibacterial microporous membranes fabricated by poly(AMS-co-DMAEMA) grafted polypropylene via melt-stretching method

Functional polypropylene (PP) is prepared by graft poly(AMS-co-DMAEMA) onto PP chains through melt blending, and then microporous membranes of functional PP are made by casting and stretching, and finally the polycation microporous membranes are obtained via quaternization. The obtained microporous membranes show good hydrophilicity and antibacterial properties.     

Growth of poly(methyl methacrylate) particles in three-component cationic microemulsions

Polymerization of methyl methacrylate (MMA) has been studied in ternary microemulsions which were stabilized by tetradecyltrimethylammonium bromide (TTAB) or stearyltrimethylammonium chloride (STAC). The sizes of MMA-swollen polymer particles (R_h) increased continuously during polymerization. This is in contrast to that of the styrene system, where R_h increased very rapidly to a maximum and then decreased continuously towards a constant value. The continuous growth of PMMA particles at 60°C are discussed. The stability of PMMA latexes increased with increasing the hydrophobic chain length of the cationic surfactant used. Traces of the coagulations of PMMA particles in the TTAB system can be seen from TEM. © 1995 John Wiley & Sons, Inc.     

Preparation of ASA (acrylonitrile-styrene-acrylate) structural latexes via seeded emulsion polymerization

Acrylonitrile-styrene-acrylate (ASA) structural latexes were synthesized in a two-stage seeded emulsion polymerization. In the first-stage, partially cross-linked poly (n-butyl acrylate) (PnBA) and poly (n-butyl acrylate-stat-2-ethyl hexyl acrylate) P (nBA-stat-2EHA) (75/25 by wt) rubber cores were synthesized, and then in the second-stage, a hard poly (styrene-stat-acrylonitrile) (SAN) (70/30 by wt) shell was grafted on to the rubber seeds. The effects of surfactant type and second-stage monomer addition mode have been investigated on the final morphology of two-stage emulsion particles. The results indicated that an application of anionic surfactant, that is, sodium dodecyl sulfonate (SDS), along with sodium persulfate (KPS) initiator for both stages, and with first-stage tert-butyl hydroperoxide (t-BHP) and second-stage KPS initiators led to a hemisphere particle morphology. On the other hand, raspberry and core-shell structures were observed for the structural latexes, which were prepared using a non-ionic surfactant, that is, nonylphenol ethoxylated polyethylene glycol (Igepal CO-850), accompanying KPS initiator for both stages. It is clear, however, that the relative surface hydrophilicity of the core phase, altered by the surfactant type considerably affected the type of morphology formed. For obtained structural latexes, the gradual addition of the second-stage monomers to the core latexes resulted in a fairly real core-shell structure with a higher shell thickness. On the contrary, a raspberry structure in which the rubber phase was enlarged by the second-stage polymer microdomains was observed for the second-stage monomer addition batch. In fact, the shell semi-batch polymerization conditions lower the shell plasticizing effect, and increase the kinetic barrier to prevent from further second-stage monomer diffusion and microdomain formation within the rubbery phase.     

醋酸淀粉/聚乳酸的制备及性能的影响研究

采用自设计的双螺杆结构挤出制备聚乳酸(PLA)/醋酸淀粉(AS)的全生物降解材料,考察材料的AS的含量和取代度对复合材料动态流变性能、机械性能的影响。研究结果表明,AS含量明显影响复合材料的力学性能、复合黏度和储能模量:当AS含量从45%增加到70%,材料的拉伸强度下降,复数黏度和储能模量则提高。随着AS取代度由1.0上升为3.0,复合材料的复数黏度和储能模量下降,拉伸强度由12.0MPa上升为15.5MPa。对复合材料进行电镜扫描分析发现,AS以海岛结构形式分散在PLA的连续相中,取代度2.0的AS与PLA相容性最好,当其质量含量达到70%,材料的拉伸强度仍然不低于10.0MPa,具有较好的机械强度。