用于10Gb/s传输系统的电吸收调制器与分布反馈激光器集成光源

采用超低压(22×１０^２Pa)选择区域生长(selective area growth, SAG)金属有机化学气相沉积(metal-organic chemical vapor deposition, MOCVD)技术成功制备了应变型InGaAsP/InGaAsP电吸收调制器(electroabsorption modulator, EAM)与分布反馈激光器(distribute feedback laser, DFB)单片集成光源的新型光电器件.实验结果表明，采用该技术制备的集成器件表现出了良好的性能：激射阈值为19 mA，出光功率接近7 mW，边模抑制比(side-mode suppression ratio, SMSR)大于40 dB，将该集成器件出射光耦合进普通单模光纤后进行测量，获得了16 dB的消光比，器件3 dB响应带宽达到了10 GHz以上.将该集成器件完全封装后成功进行了10 Gb/s非归零码(non-return zero, NRZ)的传输实验：在误码率为10^-10的传输条件下于普通单模光纤中传输了53.3 km，色散代价小于1.5 dB，动态消光比大于8 dB，且眼图清晰张开. 关键词： 超低压 选择区域生长 集成光电子器件 10 Gb/s     

Integratable and High Speed Complex-Coupled MQW-DFB Lasers Fabricated on Semi-Insulating Substrates

A novel integratable and high speed InGaAsP multi-quantum well （MQW） complex-coupled distributed feedback （DFB） laser is successfully fabricated on a semi-insulating substrate. The fabricated ridge DFB laser exhibits a threshold current of 26 mA, a slope efficiency of 0. 14 W·A^-1 and a side mode suppression ratio of 40 dB together with a 3 dB bandwidth of more than 8 GHz. The device is suitable for 10 Gbit/s optical fiber communication.     

1.3μm分布反馈二极管激光器组件

开发了一种用于光纤公用天线电视（ＣＡＴＶ）的分布反馈激光二极管组成，组件包括１．３μｍＩｎＧａＡｓ／ＩｎＰ双沟－平面掩埋双异质结（ＤＣ－ＰＢＨ）分布反馈激光二极管和光隔离器，封装在蝴蝶型管壳内，组件的出纤线性功率为２．５ｍＷ，并具有极低的失真。     

InP-based optoelectronic devices for optical fiber communications

In this contribution we report the research and development of 1.55 μm InGaAsP/InP gain-coupled DFB laser with an improved injection-carrier induced grating and of high performance 1.3 μm and 1.55 μm InGaAsP/InP FP and DFB lasers for communications. Long wavelength strained MQW laser diodes with a very low threshold current (7–10 mA) have been fabricated. Low pressure MOVPE technology has been employed for the preparation of the layered structure. A novel gain-coupled DFB laser structure with an improved injection-carrier modulated grating has been proposed and fabricated. The laser structures have been prepared by hybrid growth of MOVPE and LPE techniques and reasonably good characteristics have been achieved for resultant lasers. High performance 1.3 μm and 1.55 μm InGaAsP/InP DFB lasers have successfully been developed for CATV and trunk line optical fiber communication. Presented at the 1st Czech-Chinese Workshop “Advanced Materials for Optoelectronics”, Prague, Czech Republic, June 13–17, 1998. Kunio Tada and Yoshiaki Nakano for their cooperation in the fabrication of the novel gain-coupled DFB lasers.     

LP-MOVPE生长的低阈值1.3μm InGaAsP/InP压、张应变交替MQW激光器特性

本文国内首次报道了LP－MOVPE法生长高质量的压、张应变交替InGaAsP多量子阱结构的研制过程及其材料的高精度X－ray双晶摇摆衍射曲线和荧光光谱特性表征.在此材料基础之上制作的宽接触激光器阈值电流密度小于300A/cm²(腔长800μm),平面掩埋条形结构激光器平面掩埋异质结(PBH)条形结构多量子阱激光器阈值电流13～15mA.经过双腔面镀增透射膜后,其TE模与TM模自发发射谱光强差为3dBm,呈现偏振补偿特性.     

Performance of a dual-stage semiconductor laser amplifier for optical transmission repeater system

The performance of a dual-stage semiconductor laser amplifier consisting of a preamplifier and a power amplifier is evaluated theoretically and experimentally. The dual-stage optical amplifier can offer high-gain amplification with low noise figure by using a low-noise amplifier as a preamplifier. Using the dual-stage amplifier, 2.4 Gbits^–1 193 km optical fibre transmission was demonstrated. In addition, by applying an automatic power control system to the dual-stage amplifier, output power stabilization with wide dynamic range was obtained.     

1.3 μm planar buried heterostructure distributed feedback lasers grown by four-step MOVPE

Data are presented on InGaAsP/InP planar buried heterostructure (PBH) distributed feedback (DFB) lasers operating at 1.3 m. A four-step MOVPE process and holographic lithography are employed to fabricate these lasers. The CW laser threshold and the slope efficiency from these lasers are 9 mA and 0.23 mW mA^-1 per facet at room temperature. Single-longitudinal-mode operation with side-mode suppression of more than 35 dB is obtained at 5 mW.     

3000 km transmission of densely-spaced, 2.5 Gbit s-1 directly-modulated channels demultiplexed with a concave grating demultiplexer

WDM transmission and demultiplexing of four directly-modulated DFB lasers at 2.5 Gbit s-1, with very narrow channel spacing (50 GHz) over 3000 km of dispersion-shifted fibre has been performed with a single-span recirculating loop test-bed. A high-performance free-space concave grating demultiplexer is used for the first time in a dense WDM transmission experiment.     

DFB lasers with integrated electroabsorption modulator

We present high-performance 1550 nm DFB lasers with butt-coupled, bulk type integrated electroabsorption modulators of good manufacturability and reliability. Key issues in device design are reviewed and the strong influence of the exact detuning between lasing wavelength and modulator bandgap is demonstrated. Fibre-coupled output powers as large as 6 dBm and attenuation efficiencies as high as 12 dB V^–1 are obtained. Butterfly-packaged devices show only 1 dB penalty for 10 Gbit s^–1 NRZ transmission over 50-km standard single-mode fibre (SMF) without the use of an optical amplifier. With an optical booster amplifier, self-phase-modulation in the fibre is exploited and repeaterless 10 Gbit s^–1 transmission is possible over 150-km standard SMF.     

Feasibility study of low-power multiquantum-well vertical transmission optical amplifiers for optical interconnection

Performance of 0.98-μm InGaAs strained multiquantum-well Fabry-Perot vertical transmission optical amplifiers (MQW FP VTOAs) for optical inter-board connection is analyzed theoretically, and compared with those of GaAs MQW, GaAs bulk, and InGaAsP bulk VTOAs. A low-power operation of about 2 mA and a cascadability of several hundred boards are predicted for an InGaAs strained MQW FP VTOA.     

A simple model for optimization design of high performance In1−x−y Ga y Al x As strained MQW DFB lasers

It is well known that complex rate equations and the couple wave equation have to be solved by the method of iteration in the simulation of multi-quantum well (MQW) distributed feedback Bragg (DFB) lasers, and a long CPU time is needed. In this paper, from the oscillation condition of lasers, we propose a simple and fast model for optimization of In_1–x–y Ga _y Al _x As strained MQW DFB lasers. The well number and the cavity length of 1.55 m wavelength In_1–x–y Ga _y Al _x As MQW DFB lasers are optimized using the model. As a result, the simple model gives almost the same results as the complex one, but 90% CPU time can be saved. In addition, a low threshold, high maximum operating temperature of 550–560 K, and high relaxation oscillation frequency of over 30 GHz MQW DFB laser is presented.     

Integrated Electro-Absorption Modulation DFB Laser Based Optical True Time-Delay Feeder for X-Band Phased Array Antennas

A 4-bit optical true-time-delay feeder incorporating an integrated electro-absorption modulation distributed feedback (DFB) laser for X-band phased array antennas is demonstrated. The integrated electro-absorption modulation DFB laser is an attractive device that provides a very compact, low-cost solution for optical true-time-delay systems. The variable delay line is constructed by cascaded magneto-optic switches, which have fast switching speed. The integrated electro-absorption modulation DFB laser system shows high signal-to-noise ratio up to 58dB, and the transmission performance of the system is relatively good and accredited.     

Multi-Edge-Written Long-Period Fibre Gratings with Low PDL by Using High-Frequency CO2 Laser Pulses

A novel long-period fibre grating （LPFG） with low polarization-dependent loss （PDL） is fabricated by using a multi-edge exposure method with high frequency CO2 laser pulses. The experimental results show that the PDL of a triple-edge-written LPFG with a peak amplitude of-16.5 dB can be as low as 0.22 dB. These hovel LPFGs can find important applications in optical communication and sensing.     

Optical transmission of bulk plastic material and plastic lightguides at high optical powers

Optical transmission measurements were performed with bulk plastic materials and plastic fibres regarding the possible application as a transmission media for high optical powers. Transmission losses of PMMA bulk material and PS/PMMA core-cladding combination optical fibres were determined to be 0.757 dB m^-1 and 1.41 dB m^-1 at 514.5 nm, respectively. The core material of the investigated fibres withstands a power density of 3.8 x 10³ W mm^-2 when the light is suitably launched. With the light source available a transmitted cw output power of 2.1 W could be attained with a 1.5 m long fibre.     

Properties of PbTe/EuTe short period superlattices and their application to laser diodes

Short period superlattices (SPSLs) consisting of PbTe (E_g=0.3eV) and EuTe (E_g-2.0eV) were prepared on KCl (100) substrates by alternate growth of the PbTe (100 Å) and Eu (less than a few atomic layers) using a hot-wall technique. The structural properties were studied through x-ray diffraction and electron-probe micro analysis. The band gap of the SPSL, depending on average Eu (EuTe) composition, was determined by optical transmission measurement. It was found that the band gap of the SPSL of a small EuTe composition increases very sensitively with the EuTe composition, while that of a large EuTe composition depends only on the period length, resulting from the quantum size effect due to large band gap of EuTe (barrier). Results of magneto resistance measurements of the SPSL are also presented. A multiple quantum-well (MQW) laser was fabricated using the SPSL for barrier layers in the MQW active region and cladding layers. The laser operated up to 160 K (pulsed).     

High speed and wide temperature range uncooled 1.3-μm ridge waveguide DFB lasers

A 1.3-μm wavelength vertical-mesa ridge waveguide mulitple-quantum-well （MQW） distributed feedback （DFB） laser with high directly modulated bandwidth and wide operation temperature range is reported. With the optimization of the strained-layer MQWs in the active region, the surrounding graded-index separated-confinement-heterostructure waveguide layers, together with the optimization of the detuning and coupling coefficient of the DFB grating, high directly modulation bandwidth of 16 GHz at room temperature and wide working temperature range from -40 to 85 ℃ are obtained. The mean time to failure （MTTF） is estimated to be over 2×10^6 h. The device is suitable as light source of high-bit-rate optical transmitters with small size and reduced cost.     

Optical waveguide writing inside Foturan glass with femtosecond laser pulses

We investigated the femtosecond laser writing of optical waveguides inside Foturan glass at various pulse energies and focusing depths. An optimal waveguide fabricated solely by femtosecond laser irradiation showed a refractive index modulation of ∼1.7×10^-3 and a minimum transmission loss of ∼0.80 dB/cm. This type of waveguide had lower transmission loss than those fabricated by a hybrid process of femtosecond laser exposure and following thermal treatment. An optical splitter was also fabricated at high pulse energy. PACS 42.65.Re; 42.82.Et; 42.70.Gi     

Infrared radiation transmission through GaAs/AlGaAs quantum well infrared photodetector

This paper discusses experimental and theoretical studies of the efficiency of optical coupling in GaAs/AlGaAs multiple-quantum-well-infrared photodetectors (QWIPs) via optical diffraction grating. Optical responsivity has been studied to compare the effectiveness of different grating structures fabricated by chemical wet and reactive ion etching (RIE) methods. By the unique measurement of infrared radiation transmission spectrum of the QWIP system, we have clearly demonstrated the optical interference effect in the GaAs/ AlGaAs active MQW layer and the potential utilization of the interference effect in designing and optimizing QWIP systems has been discussed. An optical grating processed by the RIE technique is advantageous due to its accurate control over the feature size of optical apertures.     

Ultra-high-precision mid-IR spectrometer II: system description and spectroscopic performance

The development and spectroscopic performance evaluation of an ultra-sensitive, mid-IR spectrometer is reported. The laser system is based upon difference-frequency generation (DFG) at ～3.5 μm by mixing a DFB diode laser at 1562 nm and a DFB fiber laser at 1083 nm using a periodically poled LiNbO₃ crystal. DFG radiation was coupled to a 100?m optical path length astigmatic Herriott cell. Sensitive and selective spectroscopic detection of formaldehyde was performed with second-harmonic detection using Peltier-cooled HgCdTe detectors. By applying computer lock-ins, dual-beam optical noise subtraction, focus matching, thermal stabilization, active wavelength control, and advanced signal processing a sensitivity corresponding to an absorbance ～1.6×10^-7 is achieved for 260 s of averaging.     

Corrugated neat thin-film conjugated polymer distributed-feedback lasers

Wave-guided thin-film distributed-feedback (DFB) polymer lasers are fabricated by spin coating a PPV-derived semiconducting polymer, thianthrene-DOO-PPV, onto oxidised silicon wafers with corrugated second-order periodic gratings. The gratings are written by reactive ion beam etching. Laser action is achieved by transverse pumping with picosecond laser pulses (wavelength 347.15 nm, duration 35 ps). The DFB-laser surface emission and edge emission are analysed. Outside the grating region the polymer film is used for comparative wave-guided travelling wave laser (amplified spontaneous emission (ASE)) studies. The pump pulse threshold energy density for wave-guided DFB-laser action (4–9 μJ cm^-2) is found to be approximately a factor of two lower than the threshold for wave-guided travelling wave laser action. The spectral width of the DFB laser (down to Δλ_DFB≈0.07 nm) is considerably narrower than that of the travelling wave laser (Δλ_TWL≈14 nm). The DFB-laser emission is highly linearly polarised transverse to the grating axis (TE mode). Only at high pump pulse energy densities does an additional weak TM mode build up. The surface-emitted DFB-laser radiation has a low divergence along the grating direction. For both the DFB lasers and the travelling wave lasers, gain saturation occurs at high excitation energy densities. Received: 7 January 2002 / Revised version: 15 February 2002 / Published online: 14 March 2002