Facile preparation of hierarchically porous carbon using diatomite as both template and catalyst and methylene blue adsorption of carbon products

Hierarchically porous carbons were prepared using a facile preparation method in which diatomite was utilized as both template and catalyst. The porous structures of the carbon products and their formation mechanisms were investigated. The macroporosity and microporosity of the diatomite-templated carbons were derived from replication of diatom shell and structure-reconfiguration of the carbon film, respectively. The macroporosity of carbons was strongly dependent on the original morphology of the diatomite template. The macroporous structure composed of carbon plates connected by the pillar- and tube-like macropores resulted from the replication of the central and edge pores of the diatom shells with disk-shaped morphology, respectively. And another macroporous carbon tubes were also replicated from canoe-shaped diatom shells. The acidity of diatomite dramatically affected the porosity of the carbons, more acid sites of diatomite template resulted in higher surface area and pore volume of the carbon products. The diatomite-templated carbons exhibited higher adsorption capacity for methylene blue than the commercial activated carbon (CAC), although the specific surface area was much smaller than that of CAC, due to the hierarchical porosity of diatomite-templated carbons. And the carbons were readily reclaimed and regenerated.     

Simultaneous Al2O3 Doping and Sulfation in Hierarchically Porous ZrO2 Solid Acids by an One‐pot Synthesis for Enhanced Recycling Catalytic Performances

Alumina doping and sulfation in hierarchically porous zirconia solid acids have been achieved simultaneously via one‐pot and bi‐surfactant‐assisted self‐assembly process, using aluminum sulfate as both Al and SO₄^2? sources. The prepared composite solid acids showed much enhanced acidity and recycling catalytic activity for an esterification reaction compared with sulfated zirconia without alumina doping and Al‐doped sulfated zirconia without hierarchically porous structure.     

Fabrication and Characterization of Diatomite-supported Activated Carbon Functional Ceramic

Using porous diatomite ceramic as carrier and phenolic resin as carbon precursor, the activated carbon functional ceramic with the activated carbon fixed into porous ceramic was prepared by the impregnation load phenolic resin, carbonization and activation isolated air. The influences of impregnation, curing, carbonization, activation etc. on the material property were discussed. The iodine value, SEM, elemental analyzer, BET and spectrum analysis chart were used to characterize the microstructures and performance of material at different conditions. The results showed that the excellent comprehensive property of activated carbon functional ceramic was gained when it adsorbed phenolic resin in 4 h under vacuum condition at curing temperature of 150 ℃ for 0.5 h and carbonization temperature of 600 ℃ for 1.0 h, and then put into 25wt% KOH for 4.0 h at activation temperature of 700 ℃ for 1.5 h. The iodine value is 176.9 mg/g, the specific surface area can reach 86.3 m2/g and the yield of carbonization is 50.48%.     

Synthesis of High‐Surface‐Area Nitrogen‐Doped Porous Carbon Microflowers and Their Efficient Carbon Dioxide Capture Performance

Sustainable carbon materials have received particular attention in CO₂ capture and storage owing to their abundant pore structures and controllable pore parameters. Here, we report high‐surface‐area hierarchically porous N‐doped carbon microflowers, which were assembled from porous nanosheets by a three‐step route: soft‐template‐assisted self‐assembly, thermal decomposition, and KOH activation. The hydrazine hydrate used in our experiment serves as not only a nitrogen source, but also a structure‐directing agent. The activation process was carried out under low (KOH/carbon=2), mild (KOH/carbon=4) and severe (KOH/carbon=6) activation conditions. The mild activated N‐doped carbon microflowers (A‐NCF‐4) have a hierarchically porous structure, high specific surface area (2309 m² g^?1), desirable micropore size below 1 nm, and importantly large micropore volume (0.95 cm³ g^?1). The remarkably high CO₂ adsorption capacities of 6.52 and 19.32 mmol g^?1 were achieved with this sample at 0 °C (273 K) and two pressures, 1 bar and 20 bar, respectively. Furthermore, this sample also exhibits excellent stability during cyclic operations and good separation selectivity for CO₂ over N₂.     

分子筛材料在小分子吸附分离中的应用

吸附分离技术与工艺在工业上具有重要意义. 常见的吸附剂包括沸石分子筛、 金属有机框架材料、 活性炭等材料. 分子筛具有比表面积大、 稳定性高、 生产成本低等优势, 可以满足吸附分离技术中高效、 节能和环保的需求, 是一种非常有应用前景的小分子混合物分离吸附剂. 本文综合评述了吸附分离领域中常用的吸附剂材料的特点和吸附分离机理与评价方法, 总结了分子筛在空气分离、 烃类分离、 二氧化碳吸附、 芳香硫化物脱除、 一氧化碳吸附、 氮氧化物吸附、 氢气储存吸附及氢同位素分离等领域的应用, 并对基于分子筛膜的小分子混合物分离现状进行了介绍. 此外, 本文还系统分析了分子筛对不同混合物的吸附分离性能与其拓扑结构、 骨架组成及改性方法之间的关系, 并对未来的研究前景进行了展望.     

Hierarchical Porous ZSM‐5 Zeolite Synthesized by in situ Zeolitization and Its Coke Deposition Resistance in Aromatization Reaction

Hierarchical ZSM‐5 zeolites with micro‐, meso‐ and macroporosity were prepared from diatomite zeolitization through a vapor‐phase transport process on solid surfaces. The aromatization performance of the catalysts was investigated on a fixed bed reactor by using FCC gasoline as feedstock. The crystal phase, morphology, pore structures, acidity and coke depositions of the hierarchical ZSM‐5 zeolites were characterized by means of X‐ray diffraction (XRD), scanning electron microscope (SEM), N₂ adsorption/desorption, Fourier transform infrared (FT‐IR) and thermogravimetry‐mass spectrogram (TG‐MS), respectively. The results show that the prepared hierarchical ZSM‐5 zeolite possesses excellent porosity and high crystallinity, displaying an improved aromatization performance and carbon deposition resistance due to its meso‐ and macroporous structures.     

Hierarchically Porous Organic Materials Derived From Copolymers: Preparation and Electrochemical Applications

Abstract

Compared to conventional porous materials with a uniform pore size distribution, hierarchical ones containing interconnected macro-, meso-, and micropores have greatly enhanced material performance due to the increased specific surface area and mass transfer. Copolymer is a good candidate used for construction of such hierarchically porous structures, resulting from its tunable segment composition, unique phase separation, and self-assembly, etc. Hierarchically porous materials derived from copolymers can be served as a versatile support for many reactive molecules. Furthermore, hierarchically porous carbon materials (HPCMs) can also be prepared by carbonization of copolymers, one segment of which is converted to carbon while the other segment is responsible for the pore formation after its removal by pyrolysis. The obtained hierarchically porous copolymers or carbon materials have promising electrochemical applications especially in energy conversion and storage. In the present review, recent advances in preparation of hierarchically porous materials (HPMs) derived from copolymers are reviewed, and their electrochemical applications in supercapacitors, lithium-ion batteries, fuel cells, electrochemical biosensors, and electrocatalysis are also introduced. The rational design and control for the hierarchically porous microstructures are described deeply from the molecular level. Also, the relationship between the micro-structure and the electrochemical performance is revealed. This review can provide us a better understanding of both theory and experiment for the preparation of hierarchically porous organic materials and their electrochemical applications.     

活性炭表面固载十二硅钨酸的表征

活性炭表面固载十二硅钨酸的表征王新平，叶兴凯，吴越（中国科学院长春应用化学研究所，长春１３００２２）关键词硅钨酸，杂多酸，活性炭，负载型催化剂，表征由于杂多酸的优异催化性能，近年来其固载化的研究深受人们的关注［１］．活性炭是固载杂多酸较好的载体之一［...     

KOH活化木屑生物炭制备活性炭及其表征

以木屑热裂解的生物质炭为原料,氢氧化钾为活化剂,采用化学活化法制备活性炭,探讨了碱炭比、活化温度和活化时间对活性炭吸附亚甲基蓝吸附值的影响。 利用N2吸附实验、XRD和FTIR等实验技术,对原料与制备活性炭的结构与性能进行了表征。 结果表明,在碱炭质量比为1.5、活化温度750 ℃、活化时间2 h的条件下,所制备的活性炭对亚甲基蓝吸附值为255 mg/g,BET总比表面积为1514 m2/g,中孔比表面积为110 m2/g,吸附总孔容为0.821 cm3/g,中孔孔容为0.117 cm3/g,吸附平均孔径为2.170 nm。     

Liquid-phase synthesis and application of monolithic porous materials based on organic–inorganic hybrid methylsiloxanes, crosslinked polymers and carbons

Our recent progress in porous materials based on organic–inorganic hybrids, organic crosslinked polymers, and carbons is summarized. Flexible aerogels and aerogel-like xerogels with the polymethylsilsesquioxane (PMSQ) composition are obtained using methyltrimethoxysilane (MTMS) as the sole precursor. Preparation process and the flexible mechanical properties of these aerogels/xerogels are overviewed. As the derivative materials, hierarchically macro- and mesoporous PMSQ monoliths and marshmallow-like soft and bendable porous monoliths prepared from dimethyldimethoxysilane /MTMS co-precursors have been obtained. Organic crosslinked polymer monoliths with well-defined macropores are also tailored using gelling systems of vinyl monomers under controlled/living radical polymerization. The obtained polymer monoliths are carbonized and activated into activated carbon monoliths with well-defined pore properties. The activated carbon monoliths exhibit good electrochemical properties as the monolithic electrode. Some possibilities of applications for these porous materials are also discussed.     

Preparation of Corn Stalk-Walnut Shell Mix-based Activated Carbon and Its Adsorption of Malachite Green

The mix-based activated carbon derived from corn stalk and walnut shell was prepared by chemical activation method using phosphoric acid as the activator. The optimized conditions for preparation were obtained by the orthogonal experiment, the characterizations of the activated carbon were performed by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy(FTIR), Boehm's titration method and nitrogen adsorption. For the prepared mix-based activated carbon, the highest iodine number, methylene blue number and BET surface area are 720.5 mg/g, 195.0 mg/g and 1187 m²/g, respectively, and the pores are mainly mesopores. The mix-based activated carbon shows the higher adsorption capacity for malachite green than the raw materials, the activated carbons prepared only from corn stalk or walnut shell and the commercial activated carbon. The kinetics and thermodynamics of the adsorption can be satisfactorily described by the pseudo-second-order kinetic model and the Langmuir isotherm model, separately.     

微波辐射紫茎泽兰制备优质活性炭的研究

以紫茎泽兰为原料,碳酸钾为活化剂,采用超声波浸渍,微波辐射法制备活性炭.研究了浸渍方式与时间、微波功率、微波辐射时间、剂料比对活性炭吸附性能和得率的影响.得到了本实验条件下的优化工艺条件:超声波浸渍20min、120℃脱水2h,微波功率700W、微波辐射时间12min、剂料比1.25∶1.优化工艺条件下制备的活性炭碘吸附值为1470.27mg/g,亚甲基蓝吸附值为300mL/g,得率为16.35%.浸渍时间极大的缩短,微波辐射时间只有传统法活化时间的1/15左右,活性炭的吸附指标超过了国标GB/T 13803.1-1999和GB/T 13803.2-1999一级品的标准,其中碘吸附值是国家一级标准的1.47倍,亚甲基蓝吸附值是国家一级标准的2.73倍.同时,测定了该活性炭氮吸附,其BET比表面积为1540.97m2/g,总孔容为0.7393mL/g,并通过DFT表征了活性炭的孔径分布,结果表明该活性炭为微孔型活性炭.     

Monte Carlo Simulation and Experimental Studies of CO2, CH4 and Their Mixture Capture in Porous Carbons

Adsorption of carbon dioxide and methane in porous activated carbon and carbon nanotube was studied experimentally and by Grand Canonical Monte Carlo (GCMC) simulation. A gravimetric analyzer was used to obtain the experimental data, while in the simulation we used graphitic slit pores of various pore size to model activated carbon and a bundle of graphitic cylinders arranged hexagonally to model carbon nanotube. Carbon dioxide was modeled as a 3-center-Lennard-Jones (LJ) molecule with three fixed partial charges, while methane was modeled as a single LJ molecule. We have shown that the behavior of adsorption for both activated carbon and carbon nanotube is sensitive to pore width and the crossing of isotherms is observed because of the molecular packing, which favors commensurate packing for some pore sizes. Using the adsorption data of pure methane or carbon dioxide on activated carbon, we derived its pore size distribution (PSD), which was found to be in good agreement with the PSD obtained from the analysis of nitrogen adsorption data at 77 K. This derived PSD was used to describe isotherms at other temperatures as well as isotherms of mixture of carbon dioxide and methane in activated carbon and carbon nanotube at 273 and 300 K. Good agreement between the computed and experimental isotherm data was observed, thus justifying the use of a simple adsorption model.     

Impedance Spectroscopic Measurements of Pure Gas Adsorption Equilibria on Zeolites

Physisorption equilibria of gases on inert porous solids like activated carbon or molecular sieves can be characterized by measuring the (frequency dependent) capacitance of a capacitor filled with a sample adsorbent. This quantity strongly depends not only on the physico-chemical structure of the empty adsorbent in vacuum, but also on the permanent or induced dipole moments of the molecules adsorbed and of the fluid phase. Consequently, it should be possible to determine the excess mass being adsorbed on the internal surface of a highly porous solid by measurements of the dielectric constant. The aim of this work is to show for various pure gases and adsorbents that the change of the capacitance of an adsorption system depends on the adsorbed mass. Therefore, this effect can be used to characterize porous solids and their adsorbates and, for example, to check the state or the quality of industrial adsorbents during a process on site if calibration measurements have been taken (Staudt et al., 1994, 1998).     

Hydrothermal modification of carbon adsorbents

The effects of high-pressure autoclave treatments on porous structure and surface properties were studied for a variety of activated carbons (AC, synthetic and produced from plum stones) treated with water vapour, hydrogen peroxide (10–50%) or 10% aqueous ammonia solution at relatively low temperatures (250, 350, 400^○C). Surface and structural parameters of modified ACs were determined using nitrogen, water, ammonia and benzene adsorption isotherms. It was found that the effects of AC modification resulting in changes in their porous structure and surface chemistry depend on the kind of initial ACs, modifier type and concentration of modifier and treatment temperature. At the same conditions synthetic ACs are modified to a larger extent than ACs prepared using natural raw materials. Repeated treatment of a given carbon intensifies changes in its porous structure.     

Adsorption-Desorption Characteristics of Water Vapor on Functional Cattle Bone-Originated Apatites Powders with Mesopores

Microcrystals of cattle bone-originated apatites (r-HAp) were prepared by the dissolution-precipitation and freeze-drying processes. The r-HAp particles obtained gave 128 m 2 ;g m 1 specific surface area and 0.376 cm 3 ;g m 1 total pore volume and strong basic surface with mesopores. All the adsorption isotherms of water vapor at 288-308 K for the r-HAp powders obeyed IV-type in a classification of the BDDT. In the repeated adsorption-desorption operations, an adsorption hysteresis resulting from mesopores was recognized. The amounts of water vapor adsorbed obtained in the first adsorption operation were larger than those in the second adsorption operation, indicating that some portion of water vapor adsorbed to be irreversible adsorption. The water vapor-adsorption heats for the r-HAp were 45-60 kJ;mol m 1 , whose values were higher than natural diatomite. The amounts of water vapor adsorbed for the r-HAp were larger than those for the adsorbents, such as natural diatomite, aerosol silica, and activated carbon, at the relative partial pressures of 0-0.7.     

Adsorption of Carbon Dioxide on Activated Carbon

The adsorption of CO2 on a raw activated carbon A and three modified activated carbon samples B, C, and D at temperatures ranging from 303 to 333 K and the thermodynamics of adsorption have been investigated using a vacuum adsorption apparatus in order to obtain more information about the effect of CO2 on removal of organic sulfur-containing compounds in industrial gases. The active ingredients impregnated in the carbon samples show significant influence on the adsorption for CO2 and its volumes adsorbed on modified carbon samples B, C, and D are all larger than that on the raw carbon sample A. On the other hand, the physical parameters such as surface area, pore volume, and micropore volume of carbon samples show no influence on the adsorbed amount of CO2. The Dubinin-Radushkevich (D-R) equation was the best model for fitting the adsorption data on carbon samples A and B, while the Preundlich equation was the best fit for the adsorption on carbon samples C and D. The isosteric heats of adsorption on carbon samples A, B, C, and D derived from the adsorption isotherms using the Clapeyron equation decreased slightly increasing surface loading. The heat of adsorption lay between 10.5 and 28.4 kJ/mol, with the carbon sample D having the highest value at all surface coverages that were studied. The observed entropy change associated with the adsorption for the carbon samples A, B, and C (above the surface coverage of 7 ml/g) was lower than the theoretical value for mobile adsorption. However, it was higher than the theoretical value for mobile adsorption but lower than the theoretical value for localized adsorption for carbon sample D.     

Pore structure and surface properties of chemically modified activated carbons for adsorption mechanism and rate of Cr(VI)

Effects of hydrochloric acid and sodium hydroxide treatments of activated carbons (ACs) on chromium(VI) reduction were studied. The surface properties were determined by pH, acid-base values, FT-IR, and X-ray photoelectron spectrometer (XPS). And the porous structure of the activated carbons was characterized by adsorption of N(2)/77 K. The Cr(VI) adsorption experiments were carried out to analyze the influence of porous texture and surface properties changed by the chemical surface treatments of ACs on adsorption rate with carbon-solution contact time. From the experimental results, it was observed that the extent of adsorption and reduction processes depends on both microporous structure and functional groups. And the adsorption of Cr(VI) ion was more effective in the case of acidic treatment on activated carbons, resulting from the increases of acid value (or acidic functional group) of activated carbon surfaces. However, basic treatment on activated carbons was not significantly effective on the adsorption of Cr(VI) ion, probably due to the effects of the decrease of specific surface area and basic Cr(VI) in nature.     

用活性炭及部分热解碳材料进行的质子催化(英文)

The development of environmentally friendly solid acid catalysts is a priority task. Highly oxidized activated carbon and their ion-substituted (saline) forms are effective proton transfer catalysts in esterification, hydrolysis, and dehydration, and thus are promising candidates as solid acid cata-lysts. Computations by the ab initio method indicated the cause for the enchanced acidity of the carboxylic groups attached to the surface of highly oxidized carbon. The synthesis of phosphorilated carbon was considered, and the proton transfer reactions catalyzed by them in recent studies were analyzed. The development of an amorphous carbon acid catalyst comprising polycyclic carbonaceous (graphene) sheets with –SO3H, –COOH and phenolic type OH-groups was carried out. These new catalysts were synthesized by partial pyrolysis and subsequent sulfonation of carbohydrates, polymers, and other organic compounds. Their high catalytic activities in proton transfere reactions including the processing of bio-based raw materials was demonsrated.     

TiO2/柚子皮生物质活性炭复合材料的制备和吸附光降解性研究

本文以自制柚子皮生物质活性炭为原料,采用凝胶-溶胶法合成TiO2/柚子皮生物质活性炭复合材料(TiO2/BAC)。对复合材料进行SEM、FTIR、XRD等表征,并研究该复合材料对中性红、亚甲基蓝染料及甲醛的吸附降解性能。结果表明,在复合材料中柚子皮生物质活性炭的添加量为7 g、预吸附时间为2 h时,对染料具有最佳的吸附降解效果,复合材料在循环使用5次后对染料的吸附降解率仍达到了80 %以上。当活性炭的添加量为6 g、复合材料的添加量为2 g时,复合材料对甲醛的吸附降解达到最大,可达61%。表明该复合材料对中性红、亚甲基蓝染料及甲醛具有良好的吸附降解效果,有望用于废水染料的去除和家居甲醛净化。