Immobilization of Escherichia coli for detection of phage T4 using surface plasmon resonance

Phage contamination is a very serious and unavoidable problem in modern fermentation industry.It is necessary to develop sensitive and rapid phage detection methods for the early detection of phage contamination.In the present work,a real-time,rapid,specific and quantitative phage T4 detection method based on surface plasmon resonance(SPR) technique has been introduced.Escherichia coli was immobilized onto the preformed MPA self-assembled monolayer(SAM) through the widely used EDC/NHS cross-linking reaction as the recognition element.The bacteria immobilization was verified efficiently through the electrochemical measurements and fluorescence microscopy observations.The specific adsorption was much stronger than the non-specific adsorption of phage T4 binding to the biosensor surface modified by E.coli,and the latter could be neglected.The detection sensitivity reached 1×10 7 PFU/mL within 10 min.Within the experimental phage concentrations,the linear correlation between the SPR response and the phage concentration was good.The results suggest that the SPR technique is a potentially powerful tool for the phage or other virus detections,as a label-free,real-time,and rapid method.     

Sensitive detection of tuberculosis using nanoparticle-enhanced surface plasmon resonance

We show that the antigen CFP-10 (found in tissue fluids of tuberculosis patients) can be used as a marker protein in a surface-plasmon resonance (SPR) based method for early and simplified diagnosis of tuberculosis. A sandwich SPR immunosensor was constructed by immobilizing the CFP-10 antibody on a self-assembled monolayer on a gold surface, this followed by blocking it with bovine serum albumin. Following exposure of the sensor surface to a sample containing CFP-10, secondary antibody immobilized on nickel oxide nanoparticles are injected which causes a large SPR signal change. The method has a dynamic range from 0.1 to around 150 ng per mL of CFP-10, and a detection limit as low as 0.1 ng per mL. This is assumed to be due to the high amplification power of the NiO nanoparticles.

Streptavidin-enhanced surface plasmon resonance biosensor for highly sensitive and specific detection of microRNA

We are presenting a method for sensitive and specific detection of microRNA (miRNA) using surface plasmon resonance. A thiolated capture DNA probe with a short complete complementary sequence was immobilized on the gold surface of the sensor to recognize the part sequence of target miRNA, and then an oligonucleotide probe linked to streptavidin was employed to bind the another section of the target. The use of the streptavidin-oligonucleotide complex caused a ~5-fold increase in signal, improved the detection sensitivity by a factor of ~24, and lowered the detection limit to 1.7 fmol of miR-122. This specificity allowed a single mismatch in the target miRNA to be discriminated. The whole assay takes 30 min, and the surface of the sensor can be regenerated at least 30 times without loss in performance. The method was successfully applied to the determination of miRNA spiked into human total RNA samples.

Label-free detection of cancer biomarker candidates using surface plasmon resonance imaging

In this work, we present an antibody array for the detection of cancer biomarker candidates by a surface plasmon resonance (SPR) imaging sensor with polarization contrast. Responses from the SPR imaging sensor are shown to be similar to those from a conventional spectroscopy-based SPR sensor. Antibodies are spotted onto a self-assembled monolayer (SAM) composed of oligo(ethylene glycol) (OEG)-containing alkanethiol chains. Detection of two cancer biomarker candidates, activated leukocyte cell adhesion molecule/CD 166 (ALCAM) and transgelin-2 (TAGLN2), is demonstrated. Limits of detection for ALCAM and TAGLN2 are established at 6 ng/mL and 3 ng/mL, respectively, in buffer. No cross-reactivity is observed between immobilized antibodies and nonspecific antigen. Biomarker candidates are also detected in a 10% human serum solution. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Molecularly imprinted polymers for highly sensitive detection of morphine using surface plasmon resonance spectroscopy

Molecular imprinting technology is applied in surface plasmon resonance spectroscopy for highly sensitive and selective detection of morphine（MO）.As SPR-based sensor of MO,the preparation of molecular imprinted polymer is as follows: methacryhc acids（MAA）,ethylene glycol dimethacrylate（EGDMA）,azodiisobutyronitrile（AIBN） were used as functional monomer,cross-linker and initiator,respectively.The experiment results showed that morphine imprinted polymer had the performance of high sensitivity and specificity,i.e.the relative signal of SPR response was proportional to the concentration of morphine in acetonitrile in the range of 10^-9mol/L to 10^-6mol/L（1 ppb-1 ppm） with LOD of 10^-10mol/L,and MO was distinguished from its analogs,such as codeine.     

Carbon-on-metal films for surface plasmon resonance detection of DNA arrays

Surface plasmon resonance (SPR) imaging affords label-free monitoring of biomolecule interactions in an array format. A surface plasmon conducting metal thin film is required for SPR measurements. Gold thin films are traditionally used in SPR experiments as they are readily functionalized with thiol-containing molecules through formation of a gold-sulfur bond. The lability of this gold-thiol linkage upon exposure to oxidizing conditions and ultraviolet light renders these surfaces incompatible with light-directed synthetic methods for fabricating DNA arrays. It is shown here that applying a thin carbon overlayer to the gold surface yields a chemically robust substrate that permits light-directed synthesis and also supports surface plasmons. DNA arrays fabricated on these carbon-metal substrates are used to analyze two classes of biomolecular interactions: DNA-DNA and DNA-protein. This new strategy allows the combinatorial study of binding interactions directly from native, unmodified biomolecules of interest and offers the possibility of discovering new ligands in complex mixtures such as cell lysates.     

Sensing using localised surface plasmon resonance sensors

The bright colours of noble metal particles have attracted considerable interest since historical times, where they were used as decorative pigments in stained glass windows. More recently, the tuneable optical properties of metal nanoparticles and their addressability via spectroscopic techniques have brought them back into the forefront of fundamental and applied research fields. Much of the recent attention concerning metal nanoparticles such as gold and silver has been their use as small-volume, ultra-sensitive label-free optical sensors. Plasmonic nanoparticles act in this case as transducers that convert changes in the local refractive index into spectral shifts of the localized surface plasmon resonance (LSPR) band. This LSPR-shift assay is a general technique for measuring binding affinities and rates from any molecule that induces a change in the local refractive index around the metallic nanostructures. By attaching molecular recognition elements (chemical or biological ligands) on the nanostructures, specificity and selectivity to the analyte of interest are introduced into the nanosensor. In this review, we will discuss the different methods used to fabricate plasmonic nanosensors. A special emphasis will be given to techniques used to link plasmonic nanostructures to surfaces. While the difference between colorimetric and refractive index sensing approaches will be briefly described, the importance to distinguish between bulk refractive index (RI) sensing and molecular near-field refractive index sensing will be discussed. The recent progress made in the development of novel surface functionalization strategies together with the formation of optically and mechanically stable LSPR sensors will be highlighted.     

Detecting interferon-gamma release from human CD4 T-cells using surface plasmon resonance

Cytokine secretion by leukocytes is an important indicator of immune response to pathogens and therefore has significant implications in disease diagnostics. Given heterogeneity of leukocyte subsets and the ability of multiple cell subsets to secrete the same cytokines, connecting cytokine production to a specific leukocyte subset is a distinct challenge. In the present paper we describe a strategy combining antibody (Ab)-based affinity cell separation and surface plasmon resonance (SPR) for capturing human CD4 T-cells and for label-free detection of cell-secreted interferon (IFN)-γ – an important inflammatory cytokine. Human blood was introduced into a flow chamber modified with anti-CD4 Abs resulting in capture of CD4⁺ T-cells. After mitogenic activation of cells inside the flow chamber, culture medium was routed onto an SPR chip modified with monoclonal IFN-γ Abs. SPR signal observed in this experiment correlated with cytokine production by T-cells. The strategy of combining SPR detection with cell purification may be used in the future for label-free, sensitive detection of multiple cytokines or proteins secreted by the desired cell subset.     

Rapid detection of nivalenol and deoxynivalenol in wheat using surface plasmon resonance immunoassay

A surface plasmon resonance (SPR) immunoassay using a monoclonal antibody was developed to measure nivalenol (NIV) and deoxynivalenol (DON) contamination in wheat. A highly sensitive and stable DON-immobilized sensor chip was prepared, and an SPR detection procedure was developed. The competitive inhibition assay used a monoclonal antibody that cross-reacts with NIV and DON. The half maximal inhibitory concentration (IC₅₀) values of the SPR assay were 28.8 and 14.9 ng mL⁻¹ for NIV and DON, respectively. The combined responses of NIV and DON in wheat were obtained using a simultaneous detection assay in a one-step cleanup procedure. NIV and DON were separated using a commercial DON-specific immunoaffinity column (IAC) and their responses were obtained using an independent detection assay. Spiked tests using these toxins revealed that recoveries were in the range 91.5-107% with good relative standard deviations (RSDs) (0.40-4.1%) and that detection limits were 0.1 and 0.05 mg kg⁻¹ for NIV and DON, respectively. The independent detection using IAC showed detection limits of 0.2 and 0.1 mg kg⁻¹ for NIV and DON, respectively. SPR analysis results were correlated with those obtained using a conventional LC/MS/MS method for wheat co-contaminated with NIV and DON. These results suggested that the developed SPR assay is a practical method to rapidly screen the NIV and DON co-contamination of wheat and one of a very few immunoassays to detect NIV directly.     

Electrochemical enzyme immunoassay using immobilized antibody on gold film with monitoring of surface plasmon resonance signal

Sandwich immunoassay was conducted on a thin gold film set in a surface plasmon resonance (SPR) cell. Monochronal antibody (anti-IgG) was immobilized onto the gold film via 4,4′-dithiodibutyric acid (DDA) and avidin-biotin bonding. Next, IgG sample and alkaline phosphatase-conjugated anti-IgG (ALP anti-IgG) were introduced into the cell successively. Finally, p-aminophenyl phosphate (PAPP) was injected as an enzyme substrate, and the produced p-aminophenol (PAP) was electrochemically measured. Flow did not need to be stopped for incubation for the enzyme reaction, because of the thinness of the cell. In these processes, all the antigen-antibody reactions took place on the gold film. Therefore, the immobilization was performed quickly, and each process could be confirmed by SPR signal. This system had the advantage that the middle of the complicated process could be monitored. For example, the amount of antibody immobilized, which affected on the final electrochemical signal, could be confirmed in the course of immobilization. It was also convenient to investigate process conditions, such as removal of used antigens and labeled antibodies. Good correlation was obtained between the electrochemical current and the SPR signals due to the adsorption of IgG and ALP anti-IgG, and the sensitivity of the electrochemical measurement was much higher than the SPR’s.     

Enhanced surface plasmon resonance immunoassay for human complement factor 4

Using an enhanced surface plasmon resonance (SPR) immunosensor, we have determined the concentration of human complement factor 4 (C4). Antibody protein was concentrated into a carboxymethyldextran-modified gold surface by electrostatic attraction force and a simultaneous covalent immobilization of antibody based on amine coupling reaction took place. The sandwich method was applied to enhance the response signal and the specificity of antigen binding assay. The antibody immobilized surface had good response to C4 in the range of 0.02-20 μg/ml by this enhanced immunoassay. The regeneration effect by pH 2 glycine-HCl buffer was also investigated. The same antibody immobilized surface could be used more than 80 cycles of C4 binding and regeneration. In addition, the ability to determinate C4 directly from serum sample without any purification was investigated. The sensitivity, specificity and reproducibility of the enhanced immunoassay are satisfactory. The results clearly demonstrate the advantages of the enhanced SPR technique for C4 immunoassay.     

Biological sensing using transmission surface plasmon resonance spectroscopy

Ultrathin gold island films evaporated on transparent substrates offer promising transducers for chemical and biological sensing in the transmission surface plasmon resonance (T-SPR) mode. In the present work, the applicability of T-SPR-based systems to biosensing is demonstrated, using a well-established biological model system. Au island films were evaporated on polystyrene slides and modified with a biotinylated monolayer via a multistep surface reaction, the latter assisted by the good adhesion of metal islands to polystyrene. The biotin-derivatized Au island film was then used as a biological recognition surface for selective sensing of avidin binding, distinguishing between specific and nonspecific binding to the substrate. Transduction of the binding event into an optical signal was achieved by T-SPR spectroscopy, using plasmon intensity measurements, rather than wavelength change, for maximal sensitivity and convenience. T-SPR spectroscopy of Au island films is shown to be an effective tool for monitoring the binding of biological molecules to receptor layers on the Au surface and a promising approach to label-free optical biosensing.     

Rapid analysis of coumarins using surface plasmon resonance

Coumarin molecules are ubiquitous in nature. Several have come to prominence as potential clinical therapeutic candidates. The principal example is warfarin, which is a very widely prescribed anticoagulant. Other coumarin derivatives, such as aflatoxin B1, are insidious contaminants in crop-derived foodstuffs. Extreme potency is a common feature of all biochemically active coumarins and, thus reliable methods for their rapid and sensitive detection are of paramount importance. Accordingly, this review examines the current methods used in the analysis of these molecules and compares them with immunoassay-based strategies. As a case study, we report on our experiences with using coumarin-specific polyclonal, monoclonal, and recombinant antibodies in conjunction with a surface plasmon resonance-based biosensor for analysis of coumarins. We chart the assay development process and demonstrate high sensitivity and reproducibility that compares favorably with established methodologies.     

Real-time immunoassay of ferritin using surface plasmon resonance biosensor

A surface plasmon resonance (SPR) biosensor was used for the first time to determine the concentration of ferritin in both HBS-EP buffer and serum. The monoclonal antibody was immobilized on the carboxymethyl dextran-modified gold surface by an amine coupling method. The interaction of antibody with antigen was monitored in real-time. The signal was enhanced by sandwich amplification strategy to improve the sensitivity and specificity of the immunoassay, especially in serum. The linear range of the assay in serum is over 30-200 ng ml⁻¹ with the detection limit of 28 ng ml⁻¹. The sensitivity, specificity, and reproducibility of the assay are satisfactory. The analyte and enhancement antibody-binding surface could be regenerated by pH 2.0 glycine-HCl buffer and the same antibody-immobilized surface could be used for more than 50 cycles of ferritin binding and regeneration.     

Development of an X-ray detector using surface plasmon resonance

A new X-ray detector using surface plasmon resonance (SPR) is proposed. The detector consists of a prism coated with a thin metal film and semiconductor film. Optical laser pulse induces SPR condition on the metal surface, and synchronized X-ray pulse which is absorbed into the semiconductor film can be detected by measuring the change of the resonance condition of the surface plasmon. The expected time and spatial resolution of this detector is better than that of conventional X-ray detectors by combining this SPR measurement with ultra-short laser pulse as the probe beam. Our preliminary investigation using Au and ZnSe coated prism implies this scheme works well as the detector for the ultra-short X-ray pulse.     

A low-cost surface plasmon resonance instrument based on detection of resonance excitation wavelength

A laboratory-made surface plasmon resonance (SPR) instrument based on the detection of resonance excitation wavelength has been successfully fabricated. The performance and workability of the SPR instrument was demonstrated as a DNA biosensor. Biotinylated single-stranded oligonucleotides (ssDNA) were chemically immobilized on a gold-film surface of the SPR instrument as a DNA probe for the detection of its fully complementary, half-complementary and non-complementary ssDNA. The immobilization of the ssDNA probe was done by avidin-biotin linkage. The ssDNA used were 12-mer oligonucleotides. The sensing mechanism was based on the shift in resonance wavelength of an excitation light beam as the target ssDNA hybridized with the ssDNA on the gold-film surface. The linear dynamic ranges of the DNA biosensor for fully complementary and half-complementary ssDNA are 0.04-1.2 pM and 0.08-1.1 pM, respectively. The DNA biosensor showed higher sensitivity to fully complementary ssDNA than to half-complementary ssDNA. But no shift of resonance wavelength to the non-complementary ssDNA was observed.     

Surface plasmon resonance immunosensor for bacteria detection

This work describes an approach for the development of two bacteria biosensors based on surface plasmon resonance (SPR) technique. The first biosensor was based on functionalized gold substrate and the second one on immobilized gold nanoparticles. For the first biosensor, the gold substrate was functionalized with acid-thiol using the self-assembled monolayer technique, while the second one was functionalized with gold nanoparticles immobilized on modified gold substrate. A polyclonal anti-Escherichia coli antibody was immobilized for specific (E. coli) and non-specific (Lactobacillus) bacteria detection. Detection limit with a good reproducibility of 10⁴ and 10³ cfu mL⁻¹ of E. coli bacteria has been obtained for the first biosensor and for the second one respectively. A refractive index variation below 5 × 10⁻³ due to bacteria adsorption is able to be detected. The refractive index of the multilayer structure and of the E. coli bacteria layer was estimated with a modeling software.     

Nucleic acid sensor for M. tuberculosis detection based on surface plasmon resonance

Cysteine modified NH(2)-end peptide nucleic acid (PNA) (24-mer) probe and 5'-thiol end labeled deoxyribonucleic acid (DNA) probes specific to Mycobacterium tuberculosis have been immobilized onto BK-7 gold coated glass plates for the detection of complementary, one-base mismatch, non-complementary targets and complementary target sequence in genomic DNA of Mycobacterium tuberculosis using a surface plasmon resonance (SPR) technique. The DNA/Au and PNA/Au bio-electrodes have been characterized using contact angle, atomic force microscopy (AFM), electrochemical impedance spectroscopy (EIS) and cyclic voltammetric (CV) techniques, respectively. It is revealed that there is a 252 millidegrees SPR angle change in the case of PNA immobilization and 205 millidegrees for DNA immobilization, indicating increased amount of immobilized PNA molecules. Hybridization studies reveal that there is no binding of the non-complementary target to DNA/Au and PNA/Au electrode. Compared to the DNA/Au bioelectrode, PNA/Au electrode has been found to be more efficient for detection of one-base mismatch sequence. The PNA/Au bioelectrode shows better detection limit (1.0 ng ml(-1)) over the DNA-Au bioelectrode (3.0 ng ml(-1)). The values of the association (k(a)) and dissociation rate constant (k(d)) for the complementary sequence in case of the PNA/Au bioelectrode have been estimated as 8.5 x 10(4) m(-1) s(-1) and 3.6 x 10(-3) s(-1), respectively.     

Enhanced surface plasmon resonance immunosensing using a streptavidin-biotinylated protein complex

In this paper, we present a novel strategy for improving the sensitivity of surface plasmon resonance immunosensing using a streptavidin-biotinylated protein complex. This amplification strategy is based on the construction of a molecular complex between streptavidin and biotin labeled protein. The complex can be formed in a cross-linking network of molecules so that the amplification of the response signal will be realized due to the big molecular size of the complex. The results show that the amplification strategy causes a dramatic improvement of the detection sensitivity. hIgG protein could be detected in the range of 0.005-10 micrograms ml-1.     

Detection of lectin-glycan interaction using high resolution surface plasmon resonance

We report the real-time and label-free detection of direct disaccharide binding to a lectin using a differential surface plasmon resonance detection method that allows for measurement of nanomolar concentrations of disaccharides.