混凝土梁三点弯曲断裂模式转变的近场动力学模拟

混凝土结构的宏观损伤开裂与其非均质微观结构紧密相关。底部带切口的混凝土梁在进行三点弯曲破坏时,随着切口的位置由梁中向梁边转移,裂纹由从切口处萌生并生长转变为从梁的中部萌生。本文采用半均质化近场动力学（IH-PD）模型和全均质化近场动力学（FH-PD）模型,分别对混凝土梁三点弯断裂问题进行模拟研究。IH-PD模型根据混凝土中骨料体积分数随机生成不同键的组合方式,将微观尺度的非均质性引入模型,无需详细描绘骨料形状和分布即可考虑混凝土非均质性。本文将IH-PD与FH-PD模型得到的断裂模式随切口位置的变化关系,与实验结果对比,分析微观结构对混凝土梁开裂的影响;基于非均质材料特征尺寸与IH-PD模型网格参数的相关性,模拟骨料大小对混凝土梁断裂模式的影响;另外,通过在IH-PD模型中设置预损伤的方式引入随机分布的孔隙,探讨孔隙率对混凝土断裂模式的影响。     

Influence of the root radius of crack-like notches on the fracture load of brittle components

Narrow notches often cause damage that can lead to the destruction of components. The stress field in the vicinity of such crack-like notches in two-dimensional (2D) structures is similar to the stress field around equivalent cracks. Therefore similar investigations are necessary to predict the fracture load for components with cracks or narrow notches. Thus, the asymptotical stress field for a narrow notch with a rounded notch root is deduced from an Airy’s stress function. Based on this stress field a fracture criterion is developed. Comparing the theoretical fracture limit curves derived from the fracture criterion with experimental results it can be shown that for brittle material the local stress state at the fracture initiation point is the same for mode I, mixed-mode and mode II loading.     

THE USE OF THERMOELASTICITY TO EVALUATE STRESS REDISTRIBUTION AND NOTCH SENSITIVITY IN CERAMIC MATRIX COMPOSITES

Thermoelastic stress analysis was used to document the effect of composite damage on the stress distribution in three ceramic matrix composites. Composite damage was found to significantly alter the thermoelastic response of each material, with the greatest effect noted in SiC/CAS. Thermoelastic imaging of these materials affords a more complete picture of how the various damage mechanisms affect the stress distribution. In particular, a stress concentration factor computed from thermoelastic images, serves as an indicator of stress redistribution. The stress concentration factors were computed by comparing notch root to far field temperatures, and monitored after the introduction of various amounts of damage. In each material, the stress concentration factor diminished as the damaging load approached the ultimate stress. Reduction in the stress concentration is associated with local changes in modulus, mechanistically arising from combinations of fiber, matrix and interface fracture. Stress redistribution occurs as a consequence of modulus changes, leading to lower notch sensitivity in each of the tested composites.     

Peridynamic modelling of impact damage in three-point bending beam with offset notch

The nonlocal peridynamic theory has been proven to be a promising method for the material failure and damage analyses in solid mechanics.Based upon the integrodifferential equations,peridynamics enables predicting the complex fracture phenomena such as spontaneous crack nucleation and crack branching,curving,and arrest.In this paper,the bond-based peridynamic approach is used to study the impact damage in a beam with an offset notch,which is widely used to investigate the mixed I-II crack propagation in brittle materials.The predictions from the peridynamic analysis agree well with available experimental observations.The numerical results show that the dynamic fracture behaviors of the beam under the impact load,such as crack initiation,curving,and branching,rely on the location of the offset notch and the impact speed of the drop hammer.     

基于线法的U形切口混凝土梁断裂参数研究

混凝土的断裂韧度是重要的材料参数,本文利用含U形切口的三点弯曲梁试验结合临界距离线法来获得混凝土的断裂韧度．理论推导了含断裂韧度与不同根部半径的断裂失效方程,采用有限元法计算了切口应力集中系数．根据断裂失效方程和试验中的材料几何参数,利用最小二乘法拟合计算得到混凝土材料的断裂韧度和抗拉强度．对小切口半径情形,采用双K断裂准则分析计算了混凝土起裂韧度和失稳断裂韧度,分析结果表明：临界距离线法得到的材料断裂韧度与双K断裂准则中的失稳断裂韧度吻合,同时获得相应临界距离值．     

Fatigue crack-tip deformation,crack growth and life prediction in polycarbonate

Low-cycle fatigue fracture of polycarbonate is investigated. Local strain in the vicinity of the notch root and crack tip has been measured in real time by using a fine-grid method. The relationships among the local strain, crack initiation from the notch root and crack propagation of the crack tip are studied, and a method for more precise life estimation is suggested. Paper was presented at the 1992 SEM Spring Conference on Experimental Mechanics held in Las Vegas, NV on June 8–11.     

Numerical, experimental, nondestructive, and image analyses of damage progression in cast A356 aluminum notch tensile bars

Void nucleation, growth, and coalescence in A356 aluminum notch specimens was determined from a combination of experiments, finite element analysis, nondestructive analysis, and image analysis. Notch Bridgman tension experiments were performed on specimens to failure and then other specimens were tested to 90%, 95%, and 98% of the failure load. The specimens were evaluated with nondestructive X-ray tomography and optical image analysis. Finite element simulations of the notch tests were performed with an elastic–plastic internal state variable material model that incorporated the pertinent microstructures (silicon particle volume fraction and size distribution and porosity volume fraction and size distribution). Parametric finite element simulations were performed to give insight into various initial conditions and responses of the notch tensile bars. The various methods all corroborated the same damage progression.     

A void nucleation and growth based damage framework to model failure initiation ahead of a sharp notch in irradiated bcc materials

A continuum damage framework is developed and coupled with an existing crystal plasticity framework, to model failure initiation in irradiated bcc polycrystalline materials at intermediate temperatures. Constitutive equations for vacancy generation due to inelastic deformation, void nucleation due to vacancy condensation, and diffusion-assisted void growth are developed. The framework is used to simulate failure initiation at dislocation channel interfaces and grain boundaries ahead of a sharp notch. Evolution of the microstructure is considered in terms of the evolution of inelastic deformation, vacancy concentration, and void number density and radius. Evolution of the damage, i.e., volume fraction of the voids, is studied as a function of applied deformation. Effects of strain rate and temperature on failure initiation are also studied. The framework is used to compute the fracture toughness of irradiated specimens for various loading histories and notch geometries. Crack growth resistance of the irradiated specimens are computed and compared to that of virgin specimens. Results are compared to available experimental data.     

各向异性编织CMC弯曲断裂失效模型

通过对缺口弯曲断裂试验的研究发现，编织CMC存在两种断裂失效模式：界面主导的和纤维束主导的失效模式．针对这两种模式建立了界面失效模型和纤维束断裂失效模型．界面失效模型用半经验方法处理弱界面和大编织角度的断裂强度问题；纤维束断裂失效模型采用解析方法处理较强界面和小角度的断裂强度问题，为含有缺口试件的弯曲强度预报打下了初步的理论基础．     

Predicting ductile fracture of low carbon steel sheets: Stress-based versus mixed stress/strain-based Mohr–Coulomb model

Two distinct implementations of the Mohr–Coulomb failure model are used in conjunction with a non-associated quadratic plasticity model to describe the onset of fracture in low carbon steel sheets. The stress-based version corresponds to the original Mohr–Coulomb model in stress space. For the mixed stress/strain-based version, the Mohr–Coulomb failure criterion is first transformed into the space of stress triaxiality, Lode angle parameter and equivalent plastic strain and then used as stress-state dependent weighting function in a damage indicator model. Basic fracture experiments including tensile specimens of different notch radii and a punch test are performed to calibrate the material parameters of the respective models. Subsequently, the models are used to predict the crack initiation in a Hasek test and during the stamping of an anticlastic structure. Unlike for the calibration experiments, the loading history during stamping is highly non-linear. Both models can be calibrated with similar accuracy, but the strain-based model predicts the instant of onset of fracture with greater accuracy in the stamping experiment which is an advantage of the empirical damage accumulation rule.     

半结晶聚合物损伤演化的实验表征与数值模拟

损伤本构模型对研究材料的断裂失效行为有重要意义, 但聚合物材料损伤演化的定量表征实验研究相对匮乏. 通过4种高密度聚乙烯(high density polythylene, HDPE)缺口圆棒试样的单轴拉伸实验获得了各类试样的载荷-位移曲线和真应力-应变曲线, 采用实验和有限元模拟相结合的方法确定了HDPE材料不同应力状态下的本构关系, 并建立了缺口半径与应力三轴度之间的关系;采用两阶段实验法定量描述了4种HDPE试样单轴拉伸过程中的弹性模量变化, 并建立了基于弹性模量衰减的损伤演化方程, 结合中断实验和扫描电子显微镜分析了应力状态对HDPE材料微观结构演化的影响. 结果表明缺口半径越小, 应力三轴度越大, 损伤起始越早、演化越快; 微观表现为: 高应力三轴度促进孔洞的萌生和发展, 但抑制纤维状结构的产生;基于实验和有限元模拟获得的断裂应变、应力三轴度、损伤演化方程等信息提出了一种适用于聚合物的损伤模型参数确定方法, 最后将本文获得的本构关系和损伤模型用于HDPE平板的冲压成形模拟, 模拟结果与实验结果吻合良好.      

The strain energy density failure criterion applied to notched elastic solids

Application of the strain energy density failure criterion is made to plane notch problems, where the crack now becomes a special case of a more generalized approach to failure. The specific case considered is that of the plane elliptical cavity under remote tension and compression. Both failure loads and fracture trajectories are discussed. It is shown that an additional characteristic dimension provides satisfactory agreement of the theory with available data. Finally, known characteristics of fracture trajectories from a notch tip are shown to be predicted for unstable fracture conditions.     

Strain and failure analysis of graphite/epoxy plates with cracks

The objective of this investigation was to study the deformation and failure of uniaxially loaded graphite/epoxy plates with cracks and to determine the influence of notch size on failure. The specimens were quasi-isotropic laminates with cracks of various lengths. They were instrumented with strain gages, photoelastic coatings and moiré grids. Strains near the crack tip show two distinct points of rate change at strain levels of 0.002 and 0.006, the latter corresponding to the ultimate strain of the 90-deg plies. Failure near the crack tip takes the form of a damage zone consisting of ply subcracking along fibers, local delamination and fiber breakage. Failure occurs when this damage zone reaches some critical value. Measured maximum strains at failure exceeded twice the ultimate strain of the unnotched laminate. The average stress over a characteristic distance (5 mm) from the crack tip was used as a criterion to describe the influence of crack length on failure. Comparison of results with those from similar specimens with circular holes showed that strength was nearly independent of notch geometry in this case, i.e., specimens with holes and cracks of the same size had nearly the same strength.     

切口曲率半径对岩石断裂韧度KIC值的影响

本文对岩石三点弯曲试样的切口曲率半径与其断裂韧度 K_(Ic)值间的关系进行了详细的实验研究及理论分析.对岩石 K_(Ic)测试中切口的选择提出了建议方法.     

U形切口的有限断裂准则

有限断裂力学准则综合了应力和能量参数,假设裂纹或切口端部有限裂纹长度的增长．特别地,该有限裂纹的长度不是材料的基本常数,而是与构件的结构有关．基于U形切口两种形式：点方式和线方式有限断裂准则,对文献中的铝合金U形切口三点弯曲断裂实验进行了分析验证．一方面基于材料的断裂韧度和抗拉强度,预测切口件断裂载荷;另一方面根据几组不同的切口根部半径及其对应的临界切口应力强度因子,同时估算材料的断裂参数：断裂韧度和抗拉强度．将点方式和线方式两种不同形式有限断裂准则的预测结果,与平均周向应力准则、最大周向应力准则以及文献中相关结果进行了比较得出：无论是预测断裂载荷还是估算材料断裂参数,线方式有限断裂准则,与文献中相关结果比较吻合,尤其是估算的断裂韧度精度较高．     

A generalized stress intensity factor to be applied to rounded V-shaped notches

In the presence of sharp (zero radius) V-shaped notches the notch stress intensity factors (N-SIFs) quantify the intensities of the asymptotic linear elastic stress distributions. They are proportional to the limit of the mode I or II stress components multiplied by the distance powered 1 − λ_i from the notch tip, λ_i being Williams’ eigenvalues. When the notch tip radius is different from zero, the definition is no longer valid from a theoretical point of view and the characteristic, singular, sharp-notch field diverges from the rounded-notch solution very next to the notch. Nevertheless, N-SIFs continue to be used as parameters governing fracture if the notch root radius is sufficiently small with respect to the notch depth.Taking advantage of a recent analytical formulation able to describe stress distributions ahead of rounded V-notches, the paper gives a generalized form for the notch stress intensity factors, in which not only the opening angle but also the tip radius dimension is explicitly involved. Such parameters quantify the stress redistribution due to the root radius with respect to the sharp notch case.     

Microstructure-based modelling of multiphase materials and complex structures

Micromechanical approaches are frequently employed to monitor local and global field quantities and their evolution under varying mechanical and/or thermal loading scenarios. In this contribution, an overview on important methods is given that are currently used to gain insight into the deformational and failure behaviour of multiphase materials and complex structures. First, techniques to represent material microstructures are reviewed. It is common to either digitise images of real microstructures or generate virtual 2D or 3D microstructures using automated procedures (e.g. Voronoï tessellation) for grain generation and colouring algorithms for phase assignment. While the former method allows to capture exactly all features of the microstructure at hand with respect to its morphological and topological features, the latter method opens up the possibility for parametric studies with respect to the influence of individual microstructure features on the local and global stress and strain response. Several applications of these approaches are presented, comprising low and high strain behaviour of multiphase steels, failure and fracture behaviour of multiphase materials and the evolution of surface roughening of the aluminium top metallisation of semiconductor devices.     

Inverse notch sensitivity: Cracks can make nonwoven fabrics stronger

The strength of materials is always reduced in the presence of notches and cracks and this phenomenon – known as notch sensitivity – is critical in structural design. Good structural materials (ductile metals, elastomers) tend to be notch insensitive, which was considered to be the optimum behavior. Here, we report that inverse notch insensitivity (where the failure stress of the notched specimen is higher than that of the unnotched counterpart) can be achieved in polypropylene nonwoven fabrics. This behavior is only possible because of the peculiar microstructure of nonwoven fabrics, in which fracture of interfiber bonds provides a source of non-linear deformation and leads to a change in the network topology. The former facilitates crack tip blunting, spreading damage in the ligament, while the re-orientation of the fibers perpendicular to the notch plane strengthens the material and improves the maximum load bearing capability.     

Analytical representation of the non-square-root singular stress field at a finite angle sharp notch

The stress field near the tip of a finite angle sharp notch is singular. However, unlike a crack, the order of the singularity at the notch tip is less than one-half. Under tensile loading, such a singularity is characterized by a generalized stress intensity factor which is analogous to the mode I stress intensity factor used in fracture mechanics, but which has order less than one-half. By using a cohesive zone model for a notional crack emanating from the notch tip, we relate the critical value of the generalized stress intensity factor to the fracture toughness. The results show that this relation depends not only on the notch angle, but also on the maximum stress of the cohesive zone model. As expected the dependence on that maximum stress vanishes as the notch angle approaches zero. The results of this analysis compare very well with a numerical (finite element) analysis in the literature. For mixed-mode loading the limits of applicability of using a mode I failure criterion are explored.     

试样疲劳性能尺度效应的概率控制体积方法

试样尺度、缺口和加载方式通常对材料的疲劳性能具有重要影响. 因此,发展关联试样尺度、缺口和加载方式对疲劳强度影响的方法对于从材料疲劳性能到结构件疲劳性能的预测具有重要意义.首先,采用旋转弯曲加载和轴向加载方式对不同几何形状EA4T车轴钢试样进行了疲劳实验.实验结果表明, 由于试样尺度的增加,轴向加载下狗骨形试样的疲劳强度明显低于沙漏形试样; 相同寿命下,缺口显著降低试样的疲劳强度. 疲劳断口扫描电镜观测结果表明,疲劳裂纹均起源于试样表面.沙漏形试样和狗骨形试样疲劳断口大多只有一个裂纹源,而缺口试样疲劳断口均具有多裂纹源特征. 然后,采用概率控制体积方法研究了试样尺度、缺口和加载方式对疲劳强度的影响,并与临界距离和应变能密度方法进行了比较. 结果表明,概率控制体积方法能够更好地关联试样尺度、缺口和加载方式对EA4T车轴钢疲劳强度的影响.最后, 提出一种基于控制体积的结构件疲劳强度预测方法,并用于具有不连续高应力区域车轴钢试样的疲劳强度预测,预测结果与实验结果 吻合.