Improvement of storage performance of LiMn2O4/graphite battery with AlF3-coated LiMn2O4

LiMn₂O₄/graphite batteries using AlF₃-coated LiMn₂O₄ have been fabricated and their electrochemical performance including discharge capacity and cyclic and storage performances have been tested and compared with pristine LiMn₂O₄/graphite batteries. The LiMn₂O₄/graphite battery with AlF₃-coated LiMn₂O₄ shows better capacity (108.5 mAhg^?1), cyclic performance (capacity retention of 92.7 % after 70 cycles), and capacity recovery ratio (98.6 %) than the pristine LiMn₂O₄ battery. X-ray diffraction patterns shows that the spinel structure of AlF₃-coated LiMn₂O₄ can be controlled better than that of pristine LiMn₂O₄ after storage. The improvement in electrochemical performance of the AlF₃-coated LiMn₂O₄/graphite battery is due to the fact that AlF₃ acts as a stabilizer and can protect the oxide structure from damaging during storage, leading to a smaller resistance and polarization after storage.     

Investigation on the storage performance of LiMn2O4 at elevated temperature with the mixture of electrolyte stabilizer

In order to investigate the effect of different electrolytes of LiPF₆-based and LiPF₆-based with the mixed additives of ethanolamine and heptamethyldisilazane on the storage performance of LiMn₂O₄, the commercial LiMn₂O₄ are added into these different electrolytes for storing deliberately at 60 °C in air for 4 h. The results show that the electrolyte with additives can prevent LiMn₂O₄ from being eroded by HF to a certain extent, and improve the storage performance of the material. The initial discharge capacities are 97.7 and 88.4 mAh g^?1 at 0.1 and 1?C, respectively, which are much higher than that 84.4 and 63.6 mAh?g^?1 of LiMn₂O₄ stored in the electrolyte without additives. Moreover, the former LiMn₂O₄ retains 89.1 % of its initial discharge capacity at 1?C after 150 cycles, while this is not up to 84 % for the latter.     

Effect of heptamethyldisilazane on the electrochemical performance of LiMn2O4/Li

The effect of heptamethyldisilazane as an electrolyte stabilizer on the cycling performance of a LiMn₂O₄/Li cell at different rates at 30 °C and the storage performance at 60 °C is investigated systematically based on conductivity test, linear sweep voltage, electrochemical impedance spectroscopy, scanning electron microscopy, X-ray diffraction, and charge–discharge measurements. The results show that heptamethyldisilazane added into the LiPF₆-based electrolyte can increase the stability of the original electrolyte; coulomb efficiency, the initial discharge capacity, and cycling performance at different rates in a sense, meanwhile, improve the storage performance at elevated temperature, although the C-rate performance of the cell is a little worse than that without heptamethyldisilazane in the electrolyte. When the LiMn₂O₄/Li cell with heptamethyldisilazane in the LiPF₆-based electrolyte stored at 60 °C for a week cycles 300 times, the capacity retention is up to 91.18 %, which is much higher than that (87.18 %) without the additive in the electrolyte. This is mainly due to the lower solid electrolyte interface resistance (R _f) in the cell, followed by the better morphology and structure of the cathode after storage at 60 °C for a week compared with the LiMn₂O₄/Li cell without heptamethyldisilazane.     

Enhancement of the electrochemical properties of LiMn2O4 by glycolic acid-assisted sol-gel method

LiMn₂O₄ spinel cathode was synthesized by the sol–gel method by using glycolic acid as a chelating agent. The sample exhibited a pure cubic spinel structure without any impurities in the X-ray diffraction (XRD) patterns. The result of the electrochemical performances on the sample compared to those of electrodes based on LiMn₂O₄ spinel synthesized by solid state. LiMn₂O₄ synthesized by glycolic acid-assisted sol–gel method improves the cycling stability of electrode. The capacity retention of sol–gel-synthesized LiMn₂O₄ was about 90• after 100 cycles between 3.0 and 4.4 V at room temperature. The electrochemical performance of the LiMn₂O₄ (sol–gel) and LiMn₂O₄ (solid state) were investigated under 40• between 3.0 and 4.4 V. XRD results of the cathode material after 50 cycles at 40• revealed that LiMn₂O₄ (sol–gel) could effectively suppress the LiMn₂O₄ dissolving of into electrolyte and resulted in a better stability.     

ZnO-coated LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode material for lithium-ion batteries synthesized by a combustion method

ZnO-coated LiMn₂O₄ cathode materials were prepared by a combustion method using glucose as fuel. The phase structures, size of particles, morphology, and electrochemical performance of pristine and ZnO-coated LiMn₂O₄ powders are studied in detail by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), galvanostatic charge-discharge test, and X-ray photoelectron spectroscopy (XPS). XRD patterns indicated that surface-modified ZnO have no obvious effect on the bulk structure of the LiMn₂O₄. TEM and XPS proved ZnO formation on the surface of the LiMn₂O₄ particles. Galvanostatic charge/discharge test and rate performance showed that the ZnO coating could improve the capacity and cycling performance of LiMn₂O₄. The 2 wt% ZnO-coated LiMn₂O₄ sample exhibited an initial discharge capacity of 112.8 mAh g^?1 with a capacity retention of 84.1 % after 500 cycles at 0.5 C. Besides, a good rate capability at different current densities from 0.5 to 5.0 C can be acquired. CV and EIS measurements showed that the ZnO coating effectively reduced the impacts of polarization and charge transfer resistance upon cycling.     

Preparation, characterization and electrochemical performance of γ-MnO2 and LiMn2O4 as cathodes for lithium batteries

The spinel LiMn₂O₄ is a very promising cathode material with economical and environmental advantages. LiMn₂O₄ materials have been synthesized by solid state method using γ-MnO₂ as manganese source, and Li₂CO₃ or LiNO₃ as Li sources. γ-MnO₂ is a commercial battery grade electrolytic manganese dioxide (TOSOH-Hellas GH-S) and LiMn₂O₄ samples were synthesized at a calcinations temperature up to 800 °C. γ-MnO₂ and LiMn₂O₄ samples were characterized by X-ray diffraction, thermal and electrochemical measurements. X-ray powder diffraction of as prepared LiMn₂O₄ showed a well-defined highly pure spinel single phase. The electrochemical performance of LiMn₂O₄ and its starting material γ-MnO₂ was evaluated through cyclic voltammetry, galvanostatic (constant current charge-discharge cycling) The electrochemical properties in terms of cycle performance were also discussed. γ-MnO₂ showed fairly high initial capacity of about 200 mAhg⁻¹ but poor cycle performance. LiMn₂O₄ samples showed fairly low initial capacity but good cycle performance.     

Characterization and electrochemical performance of the spinel LiMn2O4 prepared from -MnO2

The preparation and characterization of the spinel LiMn₂O₄ obtained by solid state reaction from quasi-amorphous -MnO₂ is reported. A well-defined highly pure spinel was characterized from X-ray diffractograms. The average manganese valence of -MnO₂ and spinel samples was found to be 3.89±0.01 and 3.59±0.01, respectively. The electrochemical performance of the spinel was evaluated through cyclic voltammetry and chronopotentiometry. The voltammetric profiles obtained at 1 mV/s for the LiMn₂O₄ electrode in 1 M LiClO₄ dissolved in a 2:1 mixture of ethylene carbonate and dimethyl carbonate showed typical peaks for the lithium insertion/extraction reactions. The charge capacity of this electrode was found to be 110 mA h g⁻¹ for the first charge/discharge cycles.     

Origin of self-discharge mechanism in LiMn2O4-based Li-ion cells: A chemical and electrochemical approach

LiMn₂O₄-based Li-ion cells suffer from a limited cycle-life and a poor storage performance at 55 °C, both in their charged and discharged states. To get some insight on the origin of the poor 55 °C storage performance, the voltage distribution through plastic Li-ion cells during electrochemical testing was monitored by means of 3-electrode type measurements. From these measurements, coupled with chemical analysis, X-ray diffraction and microscopy studies, one unambiguously concludes that the poor performance of LiMn₂O₄/C-cells at 55 °C in their discharged state is due to enhanced Mn dissolution that increases with increasing both the temperature and the electrolyte HF content. These results were confirmed by a chemical approach which consists in placing a fresh LiMn₂O₄ electrode into a 55 °C electrolyte solution. A mechanism, based on an ion-exchange reaction leading to the Mn dissolution is proposed to account for the poor storage performance of LiMn₂O₄/C Li-ion cells in their discharged state. In order to minimize the Mn dissolution, two surface treatments were performed. The first one consists in applying an inorganic borate glass composition to the LiMn₂O₄ surface, the second one in using an acetylacetone complexing agent. Paper presented at the 4th Euroconference on Solid State Ionics, Renvyle, Galway, Ireland, Sept. 13–19, 1997     

The optimized preparation and electrochemical properties of LiMn1.95Co0.05O4 and Al2O3-coated LiMn1.95Co0.05O4

Cathode material LiMn_1.95Co_0.05O₄ for lithium ion battery was synthesized via solid state reaction, and calcination temperature and time were investigated, respectively. Thermogravimetry (TG) and differential thermal analysis (DTA) measurements were utilized to determine the calcination temperature of precursor sample. The optimized calcination temperature and time are 850 °C and 15 h. The surface of LiMn_1.95Co_0.05O₄ cathode is coated using Al₂O₃ coating materials. The phase structures, surface morphologies, and element types of the prepared LiMn_1.95Co_0.05O₄ and Al₂O₃-coated LiMn_1.95 Co_0.05O₄ were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and energy spectrum analysis (EDS). The 0.5 wt% Al₂O₃-coated compound exhibited better specific capacity and capacity retention than bare sample. The initial discharge capacity was 140.9 mAh/g and capacity retention was 96.7 % after 10 cycles at 0.1 C. Such enhancements are attributed to the presence of a stable Al₂O₃ layer which acts as the interfacial stabilizer on the surface of LiMn_1.95Co_0.05O₄.     

Spinel LiMn2O4 active material with high capacity retention

Heating the mixture of LiMn₂O₄ and NiO at 650 °C was employed to enhance the cyclability of spinel LiMn₂O₄. The results of scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared (FT-IR) spectroscopy analyses implied that a LiNi_xMn_2−xO₄ solid solution was formed on the surface of LiMn₂O₄ particles. And charge-discharge tests showed that the enhancement of the capacity retention of modified LiMn₂O₄ is significant, maintained 97.2% of the maximum capacity after 100 cycles at charge and discharge rate of C/2, while the pure one only 75.2%. The modified LiMn₂O₄ also results in a distinct improvement in rate capability, even at the rate of 12C. The improvement of electrochemical cycling stability is greatly attributed to the suppression of Jahn-Teller distortion at the surface of spinel LiMn₂O₄ particles.     

Synthesis of sea urchin-like LiMn2O4 hollow macrospheres via in situ conversion for rechargeable lithium-ion batteries

Among several materials (transition metal oxide) under development for use as a cathode in lithium-ion batteries, cubic spinel LiMn₂O₄ is one of the most promising cathode materials. In this study, the sea urchin-like LiMn₂O₄ hollow macrospheres were synthesized by using sea urchin-like α-MnO₂ precursors through solid-state in situ self-sacrificing conversion route. The as-prepared LiMn₂O₄ was assembled by many single-crystalline “thorns” of ca.10–20 nm in diameter and ca. 400–500 nm in length. Galvanostatic battery testing showed that sea urchin-like LiMn₂O₄ had an initial discharge capacity of 126.8 mAh/g at the rate of 0.2 C in the potential range between 3.0 and 4.5 V. More than 96.67 % of the initial discharge capacity was maintained for over 50 cycles. The improved electrochemical properties were attributed to the reduced particle size and enhanced electrical contacts by the materials. This particular sea urchin-like structured composite conceptually provides a new strategy for designing electrodes in energy storage applications.     

Evaluation of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>-LiNi<Subscript>0.80</Subscript>Co<Subscript>0.15</Subscript>Al<Subscript>0.05</Subscript>O<Subscript>2</Subscript> hybrid material as cathode in soft-packed lithium ion battery

The major electrochemical performances of LiMn₂O₄ (LMO)-LiNi_0.80Co_0.15Al_0.05O₂ (NCA) blending cathodes with full-range ratios are evaluated in industrial perspective. The results indicate that the reversible lithium ions can be fully utilized when NCA percentage reaches up to 50 %. The median voltages of blends are higher than the value calculated from a linear relationship of the two pristine cathodes, which is beneficial to energy density. But a synergy effect on room-temperature cycle performance is not observed for the hybrid cathode. However, the high-temperature (45 °C) capacity retention with 70 % NCA is 97.9 % after 100 cycles, higher than both pristine cathodes. It is not until NCA content increases to more than 50 % that the high-rate performance is much deteriorated. Additionally, the swelling of fully charged pouch-type battery after 4 h storage at 85 °C disappears when NCA percentage is less than 50 %. Hence, it is practically manifested that critical flaws of NCA and LMO can be compromised by blending with each other in a critical ratio. In this way, NCA can be practically used in soft-packed battery.     

Kinetic aspects of Li intercalation in mechano-chemically processed cathode materials for lithium ion batteries: Electrochemical characterization of ball-milled LiMn2O4

Micrometric LiMn₂O₄ particles are mechano-chemically modified by ball-milling to obtain a mixture of nano- and micro-scale particles. This mixture is tested as a potential active cathode material for rapid-charge Li ion batteries, and also as a model system for studying the detailed kinetics of Li intercalation/de-intercalation in such electrodes. Ragone plots recorded using galvanostatic measurements indicate enhanced power delivery characteristics of the ball-milled LiMn₂O₄ compared to its unprocessed counterpart. The processed material also exhibits improved resistance against electrolyte reactions and surface film formation. Due to these advantageous electrochemical attributes, the ball-milled LiMn₂O₄ serves as an adequately suited system for exploring certain fundamental aspects of Li intercalation in this material. Scan rate dependent slow scan cyclic voltammetry helps to identify the kinetic and diffusion controlled features of Li transport in mechano-chemically processed LiMn₂O₄. Electrochemical impedance spectroscopy substantiates these findings further and provides detailed kinetic parameters, including voltage dependent charge transfer resistance and diffusion coefficient of Li transport.     

Novel approach to preparation of LiMn2O4 core/LiNixMn2−xO4 shell composite

Combining two methods, coating and doping, to modify spinel LiMn₂O₄, is a novel approach we used to synthesize active material. First we coated the LiMn₂O₄ particles with the nickel oxide particles by means of homogenous precipitation, and then the nickel oxide-coated LiMn₂O₄ was calcined at 750 °C to form a LiNi_xMn_2−xO₄ shell on the surface of spinel LiMn₂O₄ particles. Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), cyclic voltammetry (CV) and charge-discharge test were performed to characterize the spinel LiMn₂O₄ before and after modification. The experimental results indicated that a spinel LiMn₂O₄ core is surrounded by a LiNi_xMn_2−xO₄ shell. The resulting composite showed excellent electrochemical cycling performance with an average fading rate of 0.014% per cycle. This improved cycle stability is greatly attributed to the suppression of Jahn-Teller distortion on the surface of spinel LiMn₂O₄ particles during cycling.     

Preparation of TiO2-coated LiMn2O4 by carrier transfer method

The TiO₂-coated LiMn₂O₄ has been prepared by a carrier transfer method and investigated. This novel synthetic method involved the transfer of TiO₂ into the surface of LiMn₂O₄ with Vulcan XC-72 active carbon powders as a dispersant. The X-ray diffraction shows that spinel structure of materials does not change after the coating of TiO₂. The electrochemical performance tests show that the initial discharge capacity of TiO₂-modified LiMn₂O₄ is 111.5 mA h g⁻¹, which is better than that of pristine LiMn₂O₄ (103.8 mA h g⁻¹). The cyclic performance is significantly improved after surface modification. The TiO₂-modified LiMn₂O₄ by a carrier transfer method exhibits better discharge capability and lower resistance.     

Electrochemical performance of La2O3-coated layered LiNiO2 cathode materials for rechargeable lithium-ion batteries

Uncoated and La₂O₃-coated LiNiO₂ cathode materials were synthesized by polymeric sol gel process using metal nitrate precursors at 600 °C for 10 h. The structure and electrochemical properties of the surface-coated LiNiO₂ materials were characterized by using X-ray diffraction (XRD), scanning electron microscopy (SEM), cyclic voltammetry, charge/discharge and electrochemical impedance spectroscopy techniques. X-ray powder diffraction and SEM result show that no significant bulk structural differences were observed between the lanthanum oxide coated and pristine LiMn₂O₄. The galvanostatic charge/discharge studies on the uncoated and lanthanum oxide-coated LiNiO₂-positive material at 0.5-C rate in the potential range between 3 and 4.5 V revealed that lanthanum oxide-coated positive electrode material has enhanced charge/discharge capacities; 2.0 wt.% of lanthanum oxide-coated LiNiO₂-positive material has satisfied the structural stability, high reversible capacity and high electrochemical performances.     

ZnFe2O4的固相法和水热法制备及其电化学性能研究

本文用固相反应法和水热法制备了ZnFe₂O₄材料,X射线衍射(X-ray diffraction, XRD)表明制备出来的ZnFe₂O₄为尖晶石结构,表面形貌测试 (scanning electron microscopy, SEM) 显示两种方法制备的材料的平均粒径分别为500 nm和200 nm.比表面积测试结果表明,两种方法制备的样品的比表面积分别为136.7 m² g^{-1关键词： 2O₄')" href="#">ZnFe₂O₄ 尖晶石结构 电化学性能 锂离子电池}     

A review of recent developments in the surface modification of LiMn2O4 as cathode material of power lithium-ion battery

LiMn₂O₄ (LMO) is a very attractive choice as cathode material for power lithium-ion batteries due to its economical and environmental advantages. However, LiMn₂O₄ in the 4-V region suffers from a poor cycling behavior. Recent research results confirm that modification by coating is an important method to achieve improved electrochemical performance of LMO, and the latest progress was reviewed in the paper. The surface treatment of LMO by coating oxides and nonoxide systems could decrease the surface area to retard the side reactions between the electrode and electrolyte and to further diminish the Mn dissolution during cycling test. At present, LiMn₂O₄ is the mainstreaming cathode material of power lithium-ion battery, and, especially the modified LMO, is the trend of development of power lithium-ion battery cathode material in the long term.     

Structure and electrochemical performance of LiV x Mn2 − x O4 (0 ≤ x ≤ 0.20) cathode materials for rechargeable lithium ion batteries

LiMn₂O₄ and vanadium-substituted LiV _x Mn_2???x O₄ (x?=?0.05, 0.10 0.15 and 0.20) cathode materials were synthesized by sol–gel method using aqueous solutions of metal nitrates and tartaric acid as chelating agent at 600 °C for 10 h. The structure and electrochemical properties of the synthesized materials were characterized by using X-ray diffraction, SEM, TEM and charge–discharge studies. X-ray powder diffraction analysis was changed in lattice parameters with increasing vanadium content suggesting the occupation of the substituent within LiMn₂O₄ interlayer spacing. TEM and SEM analyses show that LiV_0.15Mn_1.85O₄ has a smaller particle size and more regular morphological structure with narrow size distribution than LiMn₂O₄. It is concluded that the structural stability and cycle life improvement were due to many factors like better crystallinity, smaller particle size and uniform distribution compared to the LiMn₂O₄ cathode material. The LiV_0.15Mn_1.85O₄ cathode material has improved the structural stability and excellent electrochemical performances of the rechargeable lithium ion batteries.     

Layered lithium-rich oxide nanoparticles: low-temperature synthesis in mixed molten salt and excellent performance as cathode of lithium-ion battery

Layered lithium-rich oxide, 0.5Li₂MnO₃·0.5LiMn_1/3Ni_1/3Co_1/3O₂, is synthesized in a mixed molten salt of KCl and LiCl under 750 °C. Its morphology and structure are characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption and desorption isotherm, and its performances as cathode of lithium-ion battery are investigated by charge–discharge test and electrochemical impedance spectroscopy, with a comparison of the samples synthesized via solid-state reaction. It is found that the resulting product consists of uniform nanoparticles, 50 nm in average, which possesses a well crystallite layered structure although its synthesis temperature is low and thus exhibits excellent cyclic stability and rate capability. The resulting product delivers an initial discharge capacity of 268 mAh g^?1 at 0.1 C and has a capacity retention of 82% after 100 cycles at 1 C, compared to the 243 mAh g^?1 and 73% for the sample synthesized by solid-state reaction under 900 °C.