Enhanced ferroelectric property of (Pb0.95Ca0.05)(Nb0.02Zr0.80Ti0.20)O3 thin films prepared by RF magnetron sputtering

(Pb_0.95Ca_0.05)(Nb_0.02Zr_0.80Ti_0.20)O₃ [PCNZT] thin films were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by RF magnetron sputtering with and without a LaNiO₃ [LNO] buffer layer. Ca and Nb elements in PZT films enhance the ferroelectric property, LaNiO₃ buffer layer improves the crystal quality of the PCNZT thin films. PCNZT thin films possess better ferroelectric property than that of PZT films for Ca and Nb ion substitution, moreover, PCNZT thin films with a LNO buffer layer possess (1 0 0) orientation and good ferroelectric properties with high remnant polarization (P_r = 38.1 μC/cm²), and low coercive field (E_c = 65 kV/cm), which is also better than that of PCNZT thin films without a LNO buffer layer (P_r = 27.9 μC/cm², E_c = 74 kV/cm). The result shows that enhanced ferroelectric property of PZT films can be obtained by ion substitution and buffer layer.     

Effect of growth time on the structure, Raman shift and photoluminescence of Al and Sb codoped ZnO nanorod ordered array thin films

Al and Sb codoped ZnO nanorod ordered array thin films have been deposited on glass substrate with a ZnO seed layer by hydrothermal method at different growth time. The effect of growth time on structure, Raman shift, and photoluminescence (PL) was studied. The thin films at growth time of 5 h consist of nanorods growth vertically oriented with ZnO seed layer, and the nanorods with an average diameter of 27.8 nm and a length of 1.02 μm consist of single crystalline wurtzite ZnO crystal and grow along [0 0 1] direction. Raman scattering analysis demonstrates that the thin films at the growth time of 5 h have great Raman shift of 15 cm⁻¹ to lower wavenumber and have low asymmetrical factor Г_a/Г_b of 1.17. Room temperature photoluminescence reveals that there is more donor-related PL in films with growth time of 5 h.     

Enhanced ferroelectric properties of (Pb0.90La0.10)Ti0.975O3 multilayered thin films prepared by RF magnetron sputtering

The (Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PLT/PT), PbTiO₃/(Pb_0.90La_0.10)Ti_0.975O₃/PbTiO₃ (PT/PLT/PT) multilayered thin films with a PbO_x buffer layer were in situ deposited by RF magnetron sputtering at the substrate temperature of 600 °C. With this method, highly (1 0 0)-oriented PLT/PT and PT/PLT/PT multilayered thin films were obtained. The PbO_x buffer layer leads to the (1 0 0) orientation of the films. The dielectric, ferroelectric and pyroelectric properties of the PLT multilayered thin films were investigated. It is found that highly (1 0 0)-oriented PT/PLT/PT multilayered thin films possess higher remnant polarization 2P_r (44.1 μC/cm²) and better pyroelectric coefficient at room temperature p (p = 2.425 × 10⁻⁸ C/cm² K) than these of PLT and PLT/PT thin films. These results indicate that the design of the PT/PLT/PT multilayered thin films with a PbO_x buffer layer should be an effective way to enhance the dielectric, ferroelectric and pyroelectric properties. The mechanism of the enhanced ferroelectric properties was also discussed.     

Comparative photoemission study of the electronic properties of L-CVD SnO2 thin films

In this work we present the results of comparative XPS and PYS studies of electronic properties of the space charge layer of the L-CVD SnO₂ thin films after air exposure and subsequent UHV annealing at 400 °C, with a special emphasis on the interface Fermi level position.From the centre of gravity of binding energy of the main XPS Sn 3d_5/2 line the interface Fermi level position E_F − E_v in the band gap has been determined. It was in a good correlation with the value estimated from the offset of valence band region of the XPS spectrum, as well as from the photoemission yield spectroscopy (PYS) measurements. Moreover, from the valence band region of the XPS spectrum and PYS spectrum two different types of filled electronic band gap states of the L-CVD SnO₂ thin films have been derived, located at 6 and 3 eV with respect to the Fermi level.     

Half Ca-doped LaMnO3 films on (0 0 1) SLAO and STO substrate studied by magnetization and transport measurements

In this study, La_0.5Ca_0.5MnO₃ (LCMO) films, at the boundary between ferromagnetic metallic and charge-ordered antiferromagnetic insulator according to the bulk phase diagram, were epitaxially grown on (0 0 1) SrTiO₃ (STO) and SrLaAlO₄ (SLAO) substrates by pulsed laser deposition technique. The films were analyzed by X-ray diffraction, magnetization and magnetoresistance measurements. A considerably higher magnetization was measured for 290-nm-thick film on SLAO substrate compared to the film on STO substrate, although both films have the same chemical composition, thickness and epitaxial orientation. The film on SLAO shows a metal-insulator (MI) transition, which occurs at higher temperatures with increasing applied magnetic field, whereas only insulating behavior was observed for the 290-nm-thick film on STO except for the highest applied magnetic field (7 T). In addition, transport measurements were performed and analyzed by Mott's variable range hopping (VRH) model to correlate the resistivity of the films with the Jahn-Teller strain (ε_J−T) in the structure.     

Femtosecond Z-scan measurement of third-order optical nonlinearities in anatase TiO2 thin films

Anatase phase TiO₂ films have been grown on fused silica substrate by pulsed laser deposition technique at substrate temperature of 750 °C under the oxygen pressure of 5 Pa. From the transmission spectra, the optical band gap and linear refractive index of the TiO₂ films were determined. The third-order optical nonlinearities of the films were measured by Z-scan method using a femtosecond laser (50 fs) at the wavelength of 800 nm. The real and imaginary parts of third-order nonlinear susceptibility χ⁽³⁾ were determined to be −7.1 × 10⁻¹¹esu and −4.42 × 10⁻¹²esu, respectively. The figure of merit, T, defined by T=βλ/n₂, was calculated to be 0.8, which meets the requirement of all-optical switching devices. The results show that the anatase TiO₂ films have great potential applications for nonlinear optical devices.     

Influence of heat treatment on the structure and magnetic properties of the Co/Zr and Co/Hf multilayer amorphous films

The influence of annealing on the structure and magnetic properties of amorphous Co/Zr and Co/Hf multilayer films was studied with particular attention to the dependence of the magnetic properties, thermal stability and crystallization process on layer composition and thickness. The temperature at which crystallization commences increases from 400 to 460 °C as the layer thickness d_Zr or d_Hf increases from 6 to 18 Å, and decreases from 450 to 400 °C as d_Co increases from 12 to 18 Å. Multilayers containing 19–60 at% Zr were studied. The specific magnetization was found to increase even below the temperature at which crystallization commences. Our data are compared with non-multilayer Co–Zr amorphous films and rapidly quenched metallic glasses.     

Magnetic properties of CoPt–SiNx/Ag nanocomposite films

When the thickness of Ag under layer is 25 nm, the CoPt/Ag film has maximum out-of-plane squareness (S_⊥), minimum in-plane squareness (S_∥), and the largest out-of-plane coercivity (H_c⊥), they are 0.95, 0.35, and 15 kOe, respectively. Different volume percent of SiN_x ceramic materials were co-sputtered with Co₅₀Pt₅₀ films on the Ag under layer to reduce the grain size of the CoPt film. Comparing the X-ray diffraction pattern of CoPt-SiN_x/Ag films without annealing with that of the films which annealed at 600 and 700 °C, it is found that the intensities of CoPt (0 0 1) and CoPt (0 0 2) superlattice lines were reduced after annealing. As the SiN_x content is raised to 50 vol%, the particle size of CoPt is reduced to be about 9 nm.     

Structural and optical properties of a-Si1−xCx:H films synthesized by dc magnetron sputtering technique

Hydrogenated amorphous SiC films (a-Si_1−xC_x:H) were prepared by dc magnetron sputtering technique on p-type Si(1 0 0) and corning 9075 substrates at low temperature, by using 32 sprigs of silicon carbide (6H-SiC). The deposited a-Si_1−xC_x:H film was realized under a mixture of argon and hydrogen gases. The a-Si_1−xC_x:H films have been investigated by scanning electronic microscopy equipped with an EDS system (SEM-EDS), X-ray diffraction (XRD), secondary ions mass spectrometry (SIMS), Fourier transform infrared spectroscopy (FTIR), UV-vis-IR spectrophotometry, and photoluminescence (PL). XRD results showed that the deposited film was amorphous with a structure as a-Si_0.80C_0.20:H corresponding to 20 at.% carbon. The photoluminescence response of the samples was observed in the visible range at room temperature with two peaks centred at 463 nm (2.68 eV) and 542 nm (2.29 eV). In addition, the dependence of photoluminescence behaviour on film thickness for a certain carbon composition in hydrogenated amorphous SiC films (a-Si_1−xC_x:H) has been investigated.     

Enhancement of L10 ordered FePt by Pt buffer layer

L₁₀-ordered FePt thin films prepared by molecular-beam epitaxy on MgO (0 0 1) substrate at 320 °C with different thickness of Pt buffer layer have been investigated. The out-of-plane coercivity increases with increasing thickness of Pt buffer. The maximum values of the long-range order parameter and uniaxial magnetic anisotropy energy are 0.72 and 1.78×10⁷ erg/cm³, respectively, for films with 12 nm thick Pt buffer layer, where the c/a ratio (0.976) shows the minimum value. The reason for the enhancement in ordering is due to the proper lattice strains Pt buffer bestows on FePt layer, these strains are equal to the contraction in lattice parameter c and the expansion in a. Studies of angular-dependent coercivity revealed that the magnetization reversal behaviour shifts from a domain-wall motion dominated case towards a near rotational mode with increasing thickness of Pt buffer layer.     

Photoluminescence scanning on InAs/InGaAs quantum dot structures

The photoluminescence spectra of InAs quantum dots (QDs) embedded into four types of In_xGa_1−xAs/GaAs (x = 0.10, 0.15, 0.20 and 0.25) multi quantum well MBE structures have been investigated at 300 K in dependence on the QD position on the wafer. PL mapping was performed with 325 nm HeCd laser (35 mW) focused down to 200 μm (110 W/cm²) as the excitation source. The structures with x = 0.15 In/Ga composition in the In_xGa_1−xAs capping layer exhibited the maximum photoluminescence intensity. Strong inhomogeneity of the PL intensity is observed by mapping samples with the In/Ga composition of x ≥ 0.20-0.25. The reduction of the PL intensity is accompanied by a gradual “blue” shift of the luminescence maximum at 300 K as follows from the quantum dot PL mapping. The mechanism of this effect has been analyzed. PL peak shifts versus capping layer composition are discussed as well.     

Microstructure, magnetic and optical properties of sputtered polycrystalline ZnO films with Fe addition

Microstructure, magnetic and optical properties of polycrystalline Fe-doped ZnO films fabricated by cosputtering with different Fe atomic fractions (x_Fe) have been examined systematically. Fe addition could affect the growth of ZnO grains and surface morphology of the films. As x_Fe is larger than 7.0%, ZnFe₂O₄ grains appear in the films. All the films are ferromagnetic. The ferromagnetism comes from the ferromagnetic interaction activated by defects between the Fe ions that replace Zn ions. The average moment per Fe ion reaches a maximum value of 1.61 μ_B at x_Fe = 4.8%. With further increase in x_Fe, the average moment per Fe ion decreases because the antiferromagnetic energy is lower than the ferromagnetic one due to the reduced distance between the adjacent Fe ions. The optical band gap value decreases from 3.245 to 3.010 eV as x_Fe increases from 0% to 10%. Photoluminescence spectra analyses indicate that many defects that affect the optical and magnetic properties exist in the films.     

Structure, magnetic and optical properties of polycrystalline Co-doped TiO2 films

Co-doped TiO₂ films were fabricated under different conditions using reactive facing-target magnetron sputtering. Co doping improves the transformation of TiO₂ from anatase phase to rutile phase. The chemical valence of doped Co in the films is +2. All the films are ferromagnetic with a Curie temperature above 340 K. The average room-temperature moment per Co of the Co-doped TiO₂ films fabricated at 1.86 Pa decreases from 0.74 μ_B at x=0.03 to 0.02 μ_B at x=0.312, and decreases from 0.54 to 0.04 μ_B as x increases from 0.026 to 0.169 for the Co-doped TiO₂ films fabricated at 0.27 Pa. The ferromagnetism originates from the oxygen vacancies created by Co²⁺ dopants at Ti⁴⁺ cations. The optical band gaps value (E_g) of the Co-doped TiO₂ films fabricated at 1.86 Pa decreases linearly from 3.35 to 2.62 eV with the increasing x from 0 to 0.312. For the Co-doped TiO₂ films fabricated at 1.86 Pa, the E_g decreases linearly from 3.26 to 2.53 eV with increasing x from 0 to 0.350.     

Influence of annealing temperature on microstructure and optical properties of sol-gel derived tungsten oxide films

Tungsten oxide (WO₃) thin films have been extensively studied for their interesting physical properties and a variety of potential applications in electrochromic devices. In order to explore the possibility of using these in electrochromic devices, a preliminary and thorough study of the optical properties of the host materials is an important step. Based on this, the influence of annealing temperature on the structural, surface morphological, optical and electrochromic properties has been investigated in the present work. The host material, WO₃ films, has been prepared from an ethanolic acetylated peroxotungstic acid sol containing 5 wt.% oxalic acid dehydrate (OAD) by sol-gel technique. The monoclinic structure and textured nature change of the films with the temperature increasing have been investigated by X-ray diffraction analysis. The surface morphology evolution of the films has been characterized by SEM. The shift in absorption edge towards the higher wavelength region observed from optical studies may be due to the electron scattering effects and the optical band filling effect that reveals the crystallization of the film. The amorphous film shows better optical modulation (ΔT = 76.9% at λ = 610 nm), fast color-bleach kinetics (t_c ∼ 4 s and t_b ∼ 9 s) and good reversibility (Q_b/Q_c = 90%), thereby rendering it suitable for smart window applications.     

Substrate orientation-induced distinct ferromagnetic moment in Co:ZnO films

Dilute (3.8 at.%) cobalt-doped ZnO thin films are deposited on LiTaO₃ (LT) substrates with three different orientations [LT(1 1 0), LT(0 1 2) and LT(0 1 8)] by direct current reactive magnetron co-sputtering. The experimental results indicate that Co atoms with 2+ chemical valence are successfully incorporated into the ZnO host matrix on various oriented substrates, and the substrate orientations have a profound influence on the crystal growth and magnetization of Co:ZnO films. A large magnetic moment of 2.42μ_B/Co at room temperature is obtained in the film deposited on LT(0 1 2), while the corresponding values of the other films deposited on LT(1 1 0) and LT(0 1 8) are 1.21μ_B/Co and 0.65μ_B/Co, respectively. Furthermore, the crystal growth mode of Co:ZnO films on various oriented LT, the relationship between the microstructures and corresponding ferromagnetic properties are also discussed.     

Giant Faraday rotation in Fe–ZnSe granular films

The giant magneto-optical Faraday effect (giant Faraday rotation) of ferromagnetic metal–semiconductor matrix Fe–ZnSe granular films prepared by radio frequency sputtering is studied. The result shows that the Faraday rotation angle θ_F value of the granular films sample with Fe volume fraction x=35% is of the order of 10⁵ °/cm at room temperature. Temperature dependence of the θ_F of Fe_0.35(ZnSe)_0.65 granular films shows that θ_F value, below 150 K, increases rapidly with the decrease of the temperature, and when T=10 K θ_F value is 6×10⁵ °/cm. Through the study of the structure and dependence of magnetic properties on temperature, it has been found that the remarkable increase of the θ_F value of Fe_0.35(ZnSe)_0.65 granular films below 150 K seems to arise from the sp–d exchange interaction inside the granular films.     

Ferromagnetism at 300 K in spin-coated films of Co doped anatase and rutile-TiO2

Thin films of Ti_1−xCo_xO₂ (x=0 and 0.03) have been prepared on sapphire substrates by spin-on technique starting from metalorganic precursors. When heat treated in air at 550 and 700 °C, respectively, these films present pure anatase and rutile structures as shown both by X-ray diffraction and Raman spectroscopy. Optical absorption indicate a high degree of transparency in the visible region. Such films show a very small magnetic moment at 300 K. However, when the anatase and the rutile films are annealed in a vacuum of 1×10⁻⁵ Torr at 500 and 600 °C, respectively, the magnetic moment, at 300 K, is strongly enhanced reaching 0.36μ_B/Co for the anatase sample and 0.68μ_B/Co for the rutile one. The ferromagnetic Curie temperature of these samples is above 350 K.     

Structural studies of evaporated CoxCr1−x/Si (1 0 0) and CoxCr1−x/glass thin films

Series of Co_xCr_1−x thin films have been evaporated under vacuum onto Si (1 0 0) and glass substrates. Chemical composition and interface properties have been studied by modelling Rutherford backscattering spectra (RBS) using SIMNRA programme. Thickness ranges from 17 to 220 nm, and x from 0.80 to 0.88. Simulation of the energy spectra shows an interdiffusion profile in the thickest films, but no diffusion is seen in thinner ones. Microscopic characterizations of the films are done with X-ray diffraction (XRD) measurements. All the samples are polycrystalline, with an hcp structure and show a 〈0 0 0 1〉 preferred orientation. Atomic force microscopies (AFM) reveal very smooth film surfaces.     

Laser synthesis of semiconductor nanostructures with narrow band gap

Semiconductor nanostructures with narrow band gap were synthesized by means of laser chemical vapor deposition (LCVD) of elements from iron carbonyl vapors [Fe(CO)₅] under the action of Ar⁺ laser radiation (λ_L = 488 nm) on the Si substrate surface. The temperature dependence of the specific conductivity of these nanostructures in the form of thin films demonstrated typical semiconductor tendency and gave the possibility to calculate the band gap for intrinsic conductivity (E_g) and the band gap assigned for impurities (E_i), which were depended upon film thickness and applied electrical field. Analysis of deposited films with scanning electron microscopy (SEM) and atomic force microscopy (AFM) demonstrated their cluster structure with average size not more than 100 nm. Semiconductor properties of deposited nanostructures were stipulated with iron oxides in different oxidized phases according to X-ray photoelectron spectroscopy (XPS) analysis.These deposited nanostructures were irradiated with Q-switched YAG laser (λ_L = 1064 nm) at power density about 6 × 10⁷ W/cm². This irradiation resulted in the crystallization process of deposited films on the Si substrate surface. The crystallization process resulted in the synthesis of iron carbide-silicide (FeSi_2−xC_x) layer with semiconductor properties too. The width of the band gap E_g of the synthesized layer of iron carbide-silicide was less than for deposited films based on iron oxides Fe₂O_3−x (0 ≤ x ≤ 1).     

Write-once blue laser recording using silicon doped SbOx thin films prepared by reactive dc-magnetron sputtering

Si:SbO_x films have been deposited by reactive dc-magnetron sputtering from a Sb target with Si chips attached in Ar + O₂ with the relative O₂ content 7%. The as-deposited films contained Sb metal, Sb₂O₃, SiO, Si₂O₃ and SiO₂. The crystallization of Sb was responsible for the changes of optical properties of the films. The results of the blue laser recording test showed that the films had good writing sensitivity for blue laser beam (406.7 nm), and the recording marks were still clear even if the films were deposited in air 60 days, which demonstrated that doping silicon in SbO_x films can improve the stability of SbO_x films. High reflectivity contrast of about 36% was obtained at a writing power 6 mW and writing pulse width 300 ns.