Structural, AC, and DC magnetic properties of Zn1−xCoxFe2O4

Structural, AC and DC magnetic properties of polycrystalline Zn_1−xCo_xFe₂O₄ (x=0.2, 0.4) samples sintered at various temperatures (1100-1300 °C), and various dwell times (0.2-15 h) have been investigated thoroughly. The bulk density of the Zn_0.60Co_0.40Fe₂O₄ samples increases as the sintering temperature (T_s) increases from 1100 to 1250 °C, and above 1250 °C the bulk density decreases slightly. The Zn_0.80Co_0.20Fe₂O₄ samples show similar behavior of changes to that of Zn_0.60Co_0.40Fe₂O₄ samples except that the bulk density is found to be highest at 1200 °C. The DC magnetization as a function of temperature curves show that the Zn_0.60Co_0.40Fe₂O₄ sample is ferrimagnetic at room temperature while the Zn_0.80Co_0.20Fe₂O₄ sample is paramagnetic at room temperature. The T_c of Zn_0.80Co_0.20Fe₂O₄ sample is found to be 170 K from DC magnetization measurement. Separate measurement (AC magnetization), initial permeability as a function of temperature shows that the T_c of the Zn_0.60Co_0.40Fe₂O₄ sample is 353 K. Slight variation of T_c is observed depending on sintering condition. The initial permeability for the Zn_0.60Co_0.40Fe₂O₄ composition sintered at 1250 °C is found to be maximum.     

Enhancement of initial permeability due to Mn substitution in polycrystalline Ni0.50−xMnxZn0.50Fe2O4

The structural and magnetic properties of Mn substituted Ni_0.50−xMn_xZn_0.50Fe₂O₄ (where x=0.00, 0.10 and 0.20) sintered at various temperatures have been investigated thoroughly. The lattice parameter, average grain size and initial permeability increase with Mn substitution. Both bulk density and initial permeability increase with increasing sintering temperature from 1250 to 1300 °C and above 1300 °C they decrease. The Ni_0.30Mn_0.20Zn_0.50Fe₂O₄ sintered at 1300 °C shows the highest relative quality factor and highest initial permeability among the studied samples. The initial permeability strongly depends on average grain size and intragranular porosity. From the magnetization as a function of applied magnetic field, M(H), it is clear that at room temperature all samples are in ferrimagnetic state. The number of Bohr magneton, n(μ_B), and Neel temperature, T_N, decrease with increasing Mn substitution. It is found that Mn substitution in Ni_0.50−xMn_xZn_0.50Fe₂O₄ (where x=0.20) decreases the Neel temperature by 25% but increases the initial permeability by 76%. Possible explanation for the observed characteristics of microstructure, initial permeability, DC magnetization and Neel temperature of the studied samples are discussed.     

The structure and magnetic properties of Zn1−xNixFe2O4 ferrite nanoparticles prepared by sol–gel auto-combustion

Zn_1−xNi_xFe₂O₄ ferrite nanoparticles were prepared by sol–gel auto-combustion and then annealed at 700 °C for 4 h. The results of differential thermal analysis indicate that the thermal decomposition temperature is about 210 °C and Ni–Zn ferrite nanoparticles could be synthesized in the self-propagating combustion process. The microstructure and magnetic properties were investigated by means of X-ray diffraction, scanning electron microscope, and Vibrating sample magnetometer. It is observed that all the spherical nanoparticles with an average grain size of about 35 nm are of pure spinel cubic structure. The crystal lattice constant declines gradually with increasing x from 0.8435 nm (x=0.20) to 0.8352 nm (x=1.00). Different from the composition of Zn_0.5Ni_0.5Fe₂O₄ for the bulk, the maximum M_s is found in the composition of Zn_0.3Ni_0.7Fe₂O₄ for nanoparticles. The H_c of samples is much larger than the bulk ferrites and increases with the enlarging x. The results of Zn_0.3Ni_0.7Fe₂O₄ annealed at different temperatures indicate that the maximum M_s (83.2 emu/g) appears in the sample annealed at 900 °C. The H_c of Zn_0.3Ni_0.7Fe₂O₄ firstly increases slightly as the grain size increases, and presents a maximum value of 115 Oe when the grains grow up to about 30 nm, and then declines rapidly with the grains further growing. The critical diameter (under the critical diameter, the grain is of single domain) of Zn_0.3Ni_0.7Fe₂O₄ nanoparticles is found to be about 30 nm.     

Heat treatment effects on spinel phase of Zn x Ni1 − x Fe2O4 and MnFe2O4 nanoferrites

We report the effects of heat treatment on Zn _x Ni_1???x Fe₂O₄ (x?= 0, 0.5 and 1.0) and MnFe₂O₄ ferrite nanoparticles. The as-prepared compounds were sintered from 400°C to 1100°C. Pure ZnFe₂O₄ (x?= 1.0) and MnFe₂O₄ could be obtained under low reaction temperature of 200°C. NiFe₂O₄ (x?= 0) and Zn_0.5Ni_0.5Fe₂O₄ (x?= 0.5) nanoferrites crystallized with single phase cubic spinel structure after annealing at 600°C. The single phase cubic spinel structure of these compounds was destroyed after annealing at temperature above 700°C. The magnetization measurements indicate superparamagnetic behavior of the nanosized compounds produced.     

Magnetoresistive properties of Zn1−xCoxFe2O4 ferrites

The magnetic and magnetoresistive properties of spinel-type Zn_1−xCo_xFe₂O₄ (x=0, 0.2 and 0.4) ferrites are extensively investigated in this study. A large negative magnetoresistance (MR) effect is observed in Zn_1−xCo_xFe₂O₄ ferrites of spinel structure. These materials are either ferrimagnetic or paramagnetic at room temperature, and show a spin-(cluster) glass transition at low temperatures, depending on the chemical compositions. The MR curves as a function of magnetic fields, MR(H), are parabolic at all temperatures for paramagnetic polycrystalline ZnFe₂O₄. The MR for ZnFe₂O₄ at 110 K in the presence of 9 T applied magnetic field is 30%. On the other hand, MR(H) are linear for x=0.2 and 0.4 ferrimagnetic Zn_1−xCo_xFe₂O₄ samples up to 9 T. The MR effect is independent of the sintering temperatures, and can be explained with the help of the spin-dependent scattering and the Yafet–Kittel angle of Zn_1−xCo_xFe₂O₄ mixed ferrites.     

Structural,electrical transport,and magnetic properties of Ni1−xZnxFe2O4

Structural, electrical, and magnetic properties of Ni_1−xZn_xFe₂O₄ (x=0.2, 0.4) samples sintered at various temperatures have been investigated thoroughly. The bulk density of the Ni_0.8Zn_0.2Fe₂O₄ samples increases as the sintering temperature (T_s) increases from 1200 to 1300 °C and above 1300 °C the bulk density decreases slightly. The Ni_0.6Zn_0.4Fe₂O₄ samples show similar behavior of changes to that of Ni_0.8Zn_0.2Fe₂O₄ samples, except that the bulk density is found to be the highest at 1350 °C. The DC electrical resistivity, ρ(T)$\rho (T)$, decreases as the temperature increases indicating that the samples have semiconductor-like behavior. As the Zn content increases, the Curie temperature (T_c), resistivity, and the activation energy decrease while the magnetization, initial permeability, and the relative quality factor (Q) increases. A Hopkinson peak is obtained near T_c in the real part of the initial permeability vs. temperature curves. The ferrite with higher permeability has a relatively lower resonance frequency. The initial permeability and magnetization of the samples has been found to correlate with density, average grain sizes. Possible explanation for the observed structural, magnetic, and changes of resistivity behavior with various Zn content are discussed.     

基片对交替溅射制备的MnZn铁氧体薄膜结构和磁性的影响

使用成分分别为MnFe₂O₄和ZnFe₂O₄的靶,使用射频溅射交替沉积制备了成分不同的Mn_1-xZn_xFe₂O₄薄膜,沉积薄膜所用基片分别为单晶硅Si（100）,氧化的单晶硅SiO₂/Si（100）, ZnFe₂O₄为衬底的单晶硅ZnFe< 关键词： MnZn铁氧体 纳米晶 软磁性 磁性薄膜     

Magnetic and bioactivity evaluation of ferrimagnetic ZnFe2O4 containing glass ceramics for the hyperthermia treatment of cancer

Glass ceramics of the composition xZnO·25Fe₂O₃·(40−x)SiO₂·25CaO·7P₂O₅·3Na₂O were prepared by the melt-quench method using oxy-acetylene flame. Glass-powder compacts were sintered at 1100 °C for 3 h and then rapidly cooled at −10 °C. X-ray diffraction (XRD) revealed 3 prominent crystalline phases: ZnFe₂O₄, CaSiO₃ and Ca₁₀(PO₄)₆(OH)₂. Vibrating sample magnetometer (VSM) data at 10 KOe and 500 Oe showed that saturation magnetization, coercivity and hence hysteresis area increased with the increase in ZnO content. Nano-sized ZnFe₂O₄ crystallites were of pseudo-single domain structure and thus coercivity increased with the increase in crystallite size. ZnFe₂O₄ exhibited ferrimagnetism due to the random distribution of Zn²⁺ and Fe³⁺ cations at tetrahedral A sites and octahedral B sites. This inversion/random distribution of cations was probably due to the surface effects of nano-ZnFe₂O₄ and rapid cooling of the material from 1100 °C (thus preserving the high temperature state of the random distribution of cations). Calorimetric measurements were carried out using magnetic induction furnace at 500 Oe magnetic field and 400 KHz frequency. The data showed that maximum specific power loss and temperature increase after 2 min were 26 W/g and 37 °C, respectively for the sample containing 10% ZnO. The samples were immersed in simulated body fluid (SBF) for 3 weeks. Scanning electron microscope (SEM), energy dispersive spectroscopy (EDX) and XRD results confirmed the growth of precipitated hydroxyapatite phase after immersion in SBF, suggesting that the ferrimagnetic glass ceramics were bioactive and could bond to the living tissues in physiological environment.     

The colloidal stability and core-shell structure of magnetite nanoparticles coated with alginate

The adsorption of alginate (Alg) onto the surface of in water dispersed Fe₃O₄ nanoparticles and zeta potential of alginate-coated Fe₃O₄ nanoparticles have been investigated to optimize the colloidal stability of Alg-coated Fe₃O₄ nanoparticles. The adsorption amount of Alg increased with the decrease of adsorption pH. The zeta potential of Fe₃O₄ nanoparticles shifted to a lower value after adsorption of Alg. The lower adsorption pH was the lower zeta potential of Fe₃O₄ nanoparticles became. The Alg-coated Fe₃O₄ nanoparticles were found to be stabilized by steric and electrostatic repulsions. Those prepared at pH 6 were not stable around pH 5, and those prepared at pH 4 became unstable at pH below 3.5. Alg of M_w 45 kDa was a little bit more adsorbed onto nanoparticles surface than that of M_w 24 kDa. An average Fe₃O₄ core size of 9.3 ± 1.7 nm was found by transmission electronic microscopy. An average hydrodynamic diameter of 30-150 nm was measured by photon correlation spectroscopy. However, an average core size of 10 nm and an average hydrodynamic diameter of 38 nm were estimated from the magnetization curve of the concentrated magnetic fluids (MFs). The maximum available saturation magnetization of MFs was about 3.5 kA/m.     

Heat treatment effects on microstructure and magnetic properties of Mn-Zn ferrite powders

Mn-Zn ferrite powders (Mn_0.5Zn_0.5Fe₂O₄) were prepared by the nitrate-citrate auto-combustion method and subsequently annealed in air or argon. The effects of heat treatment temperature on crystalline phases formation, microstructure and magnetic properties of Mn-Zn ferrite were investigated by X-ray diffraction, thermogravimetric and differential thermal analysis, scanning electron microscopy and vibrating sample magnetometer. Ferrites decomposed to Fe₂O₃ and Mn₂O₃ after annealing above 550 °C in air, and had poor magnetic properties. However, Fe₂O₃ and Mn₂O₃ were dissolved after ferrites annealing above 1100 °C. Moreover, the 1200 °C annealed sample showed pure ferrite phase, larger saturation magnetization (M_s=48.15 emu g⁻¹) and lower coercivity (H_c=51 Oe) compared with the auto-combusted ferrite powder (M_s=44.32 emu g⁻¹, H_c=70 Oe). The 600 °C air annealed sample had the largest saturation magnetization (M_s=56.37 emu g⁻¹) and the lowest coercivity (H_c=32 Oe) due to the presence of pure ferrite spinel phase, its microstructure and crystalline size.     

Effect of nanoparticles on the magnetic properties of Mn–Zn soft ferrite

In this paper, the effect of nanostructures on the magnetic properties like the specific saturation magnetization (σ_S) and the coercivity (H_C) for Mn_0.4Zn_0.6Fe₂O₄ ferrite prepared by the co-precipitation method has been presented. We have shown by means of X-ray diffraction that the resulting ferrite is made up of nanoparticles, and that the average size of these nanoparticles calculated with the Scherrer formula depends upon the sintering temperature. When the sintering temperature is increased from 500 to 900 °C, the average nanoparticle diameter varies from 19.3 to 36.4 nm. The nanoparticle phase is further confirmed by scanning electron microscopy (SEM). Both results are found to be in good agreement. The magnetic properties are explained on the basis of the single-domain and multi-domain theory.     

Magnetic,electronic and structural properties of ZnxFe3−xO4

A series of samples Zn_xFe_3−xO₄ have been prepared by the chemical coprecipitation technique and characterized by X-ray diffraction (XRD), vibrating sample magnetometry (VSM) and X-ray photoelectron spectroscopy (XPS). XRD demonstrates all the samples of Zn_xFe_3−xO₄ have a spinel structure same as Fe₃O₄. The magnetic hysteresis loops of Zn_xFe_3−xO₄ obtained from VSM indicate that the saturation magnetization has a maximum when x is ∼1/3. The chemical states of Fe atoms and Zn atoms in zinc ferrites have been measured using XPS and Auger electron spectroscopy (AES). The Fe 2p core-level XPS spectra and Zn L₃M₄₅M₄₅ Auger peaks have been analyzed and the results have been discussed in correlation with the samples’ magnetic properties. These results suggest most of Zn atoms occupy the tetrahedral sites and a small amount of them occupy the octahedral sites.     

Li0.5Fe2.5−xMnxO4 ferrite sintered from microwave-induced combustion

Li_0.5Fe_2.5−xMn_xO₄ (0≦x≦1.0) powders with small and uniformly sized particles were successfully synthesized by microwave-induced combustion, using lithium nitrate, ferric nitrate, manganese nitrate and carbohydrazide as the starting materials. The process takes only a few minutes to obtain as-received Mn-substituted lithium ferrite powders. The resultant powders annealed at 650 ^°C for 2 h and were investigated by thermogravimeter/differential thermal analyzer (TG/DTA), X-ray diffractometer (XRD), transmission electron microscopy (TEM), vibrating sample magnetometer (VSM), and thermomagnetic analysis (TMA). The results revealed that the Mn content were strongly influenced the magnetic properties and Curie temperature of Mn-substituted lithium ferrite powder. As for sintered Li_0.5Fe_2.5−xMn_xO₄ specimens, substituting an appropriate amount of Mn for Fe in the Li_0.5Fe_2.5−xMn_xO₄ specimens markedly improved the complex permeability and loss tangent.     

Effect of size and synthesis route on the magnetic properties of chemically prepared nanosize ZnFe2O4

Magnetization of the ZnFe₂O₄ sample of average size 4 nm measured with SQUID in the temperature range 5–300 K shows anomalous behaviour in field cooled (FC) and zero-field-cooled (ZFC) conditions. The FC and ZFC curves measured in 50 Oe field cross each other a little before the peaks. No such anomaly is observed with samples of 6 nm particle size made with the same procedure. The characteristics of the FC and ZFC curves are very different in ZnFe₂O₄ samples of the same size (6 nm) made via two different chemical routes. The genesis of these differences are suggested to be in cationic configuration and spin disorder. Fe-extended X-ray absorption fine structure (EXAFS) studies show that there is around 80% inversion in case of zinc ferrite (ZnFe₂O₄) with the particle size 4 nm, whereas ZnFe₂O₄ of size 6 nm shows 40% inversion. The samples with an average particle size of 7 nm and more show negligible inversion. Theoretical simulations suggest that the electrostatic energy of the system plays a crucial role in deciding the cationic configuration of spinel ferrites.     

Magnetic properties of disordered ferrite and ilmenite-hematite thin films

We have synthesized thin films of disordered zinc ferrite (ZnFe₂O₄) and ilmenite-hematite (FeTiO₃-Fe₂O₃) solid solution, the former and the latter of which are interesting from the viewpoints of magnetooptics and spintronics, respectively, by utilizing sputtering and pulsed laser deposition methods, and have explored their magnetic, magnetooptical, and electrical properties. Although ZnFe₂O₄ possesses a normal spinel structure as its stable phase, some of the Fe³⁺ ions occupy the tetrahedral as well as the octahedral sites in ZnFe₂O₄ of which the sputtered thin film is composed. Consequently, the as-deposited thin film manifests large magnetization even at room temperature although the magnetic phase transition temperature of the stable phase of ZnFe₂O₄ is as low as 10 K. Also, the thin film exhibits a cluster spin glass transition at a temperature as high as 325 K. Furthermore, the ZnFe₂O₄ thin films exhibit large Faraday effects at a wavelength of 400 nm or so. The ilmenite-hematite solid solution is one of the ferrimagnetic semiconductors. Most of the compositions possess Curie temperatures higher than room temperature, and the type of carrier can be tuned only by changing the composition. We have succeeded in synthesizing solid-solution thin films of various compositions grown epitaxially on sapphire substrates with a (0 0 0 1) plane, and have shown that the thin films are ferrimagnetic semiconductors.     

Structural and magnetic properties of Co1−xZnxFe2O4 nanoparticles by co-precipitation method

Co_1−xZn_xFe₂O₄ nanoparticles were prepared by co-precipitation method with x varying from 0 to 1.0. The powder samples were characterized by X-ray diffraction (XRD), vibrating sample magnetometer (VSM) and Fourier transform infrared spectroscopy (FTIR). The average crystallite sizes of the particles were determined from XRD. X-ray analysis showed that the samples were cubic spinel. The average crystallite size (D_aveXR) of the particles precipitated was found to vary from 6.92 to 12.02 nm decreasing with the increase in zinc substitution. The lattice constant (a_o) increased with the increase in zinc substitution. The specific saturation magnetization (M_S) of the particles was measured at room temperature. The magnetic parameters such as M_S, H_c, and M_r were found to decrease with the increase in zinc substitution. FTIR spectra of the Co_1−xZn_xFe₂O₄ with x varying from 0 to 1.0 in the range 400–4000 cm⁻¹ were reported. The spinel structure and the crystalline water adsorption of Co_1−xZn_xFe₂O₄ nanoparticles were studied by using FTIR.     

Synthesis and magnetic properties of Co–Zn magnetic fluid

Co_1−xZn_xFe₂O₄ (with x varying from 0 to 0.7) nanoparticles to be used for ferrofluid preparation were prepared by chemical co-precipitation method. The fine particles were suitably dispersed in transformer oil using oleic acid as the surfactant. The magnetization (M_s) and the size of the particles were measured at room temperature. The magnetization (M_s) was found to decrease with the increase in zinc substitution. The magnetic particle size (D_m) of the fluid was found to vary from 11.19 to 4.25 nm decreasing with the increase in zinc substitution.     

Correlation of grain boundary nature with magnetization in RF-sputtered lithium-zinc ferrite thin films

A significant advance in the understanding of grain boundary contribution to magnetization in nanocrystalline ferrite thin films is demonstrated in this paper. RF-sputtered, room-temperature-deposited lithium-zinc ferrite thin films (Li_0.5−x/2Zn_xMn_0.1Fe_2.35−x/2O₄, with x=0.0, 0.16, 0.32 and 0.48) have been thermally annealed ex-situ at 850 °C and the in-plane magnetic measurements have been performed using a vibrating sample magnetometer. The percentage deviation between bulk and film magnetization (δ_M) is observed to decrease with increasing Zn concentration, till x=0.32, and then it increases. Macro-texture measurements using X-ray orientation distribution function and micro-texture measurements using orientation imaging microscopy show reverse trend in the extent of crystallographic texturing and in the computed fraction of low-angle grain boundaries. This study brings out a correlation between low-angle grain boundary concentration and δ_M.     

Production of bulk dilute ferromagnetic semiconductor by mechanical milling

We tried to prepare the bulk dilute ferromagnetic semiconductor (DMS) by mechanical milling (MM). Experimental results were as following: (1) The observation of X-ray diffraction and transmitting electron microscopy showed that the particle diameter of host ZnO powder were reduced to about 10 nm by MM. (2) The MM for the mixtures of V₂O₅/ZnO or γ-Fe₂O₃/ZnO realizes the V- or Fe-doped ZnO nano-powders. (3) The values of magnetization under the field of 5 kOe were nearly saturated to 0.8×10⁻³ to 3×10⁻³ μ_B/V-ion for V_xZn_1−xO (x=0.05, 0.1 and 0.2), and 0.2–0.3 μ_B/Fe-ion for Fe_xZn_1−xO (x=0.05 and 0.1) at room temperature. The above results show that the ferromagnetic DMS powder of V_xZn_1−xO and Fe_xZn_1−xO were successfully prepared by MM method.     

Reentrant spin glass behavior and large initial permeability of Co0.5−xMnxZn0.5Fe2O4

A series of polycrystalline ferrites having nominal chemical composition Co_0.50−xMn_xZn_0.5Fe₂O₄ (0<x<0.4) have been synthesized by the solid-state reaction technique. The XRD analysis confirms single phase cubic spinel structure for all compositions. Lattice constant increases from 0.84195 to 0.84429 nm with the increasing Mn content and obeys Vegard's law. The average grain size increases by increasing both Mn content and sintering temperatures. Room temperature saturation magnetization increases for x=0.1 and decreases for increasing Mn content. The coercivity decreases with increasing Mn content due to the decrease of anisotropy constant. A reentrant spin glass behavior of these samples is observed from the zero field cooled magnetization measurements. The real part of the initial permeability increases by increasing both Mn content and sintering temperatures. This is due to the homogeneous grain growth and densification of the ferrites. The highest initial permeability 137 is observed for x=0.4 sintered at 1573 K on the other hand, the highest relative quality factor (2522) is obtained for the sample Co_0.2Mn_0.3Zn_0.5Fe₂O₄ sintered at 1523 K. The Mn substituted Co_0.50−xMn_xZn_0.5Fe₂O₄ ferrites showed improved magnetic properties.