Magnetic properties of rare earth ion (Sm) added nanocrystalline Mg-Cd ferrites, prepared by oxalate co-precipitation method

Nanocrystalline ferrite powder having the general formula Mg_1−xCd_xFe₂O₄+5% Sm³⁺ (x=0, 0.2, 0.4, 0.6, 0.8 and 1.0) was synthesized by chemical oxalate co-precipitation technique. The synthesized powder was characterized by X-ray, IR and SEM techniques. The XRD analysis confirms cubic spinel phase with orthoferrite secondary phase. The lattice constant increases with increase in Cd²⁺ content (x). It is smaller than that for pure Mg-Cd ferrites. The average crystallite size lies in the range 28.69-32.66 nm. Saturation magnetization and magnetic moment increase with cadmium content up to x=0.4 and decrease thereafter. This is attributed to the existence of localized canted spin. The decrease in saturation magnetization and magnetic moment beyond x=0.4 is due to the presence of triangular spin arrangement on B-site. Coercivity and remanent magnetization decrease while Y-K angles increase with Cd²⁺ content. The Sm³⁺ addition improves the magnetic properties.     

Structural and some magnetic properties of manganese-substituted lithium ferrites

The structural and magnetic properties of Mn-substituted lithium ferrites having the general formula Li_0.5−0.5xMn_xFe_2.5−0.5xO₄ (where x=0.0–1.0) prepared by the standard ceramic technique have been studied. Single phase cubic structure is confirmed by X-ray diffractometer. This result demonstrates that the samples are homogeneous, and the sharp peaks reveal that the samples are in crystalline form. The lattice parameter ‘a’ and average grain diameter ‘D’ increase with increasing Mn²⁺ ion substitution. The saturation magnetization and the experimental magnetic moment are found to increase with manganese up to x=0.5 and then tends to decrease for x>0.5. The increase in magnetic moment with manganese is attributed to Neel's two sublattice model according to which the magnetic moment is the vector sum of lattice magnetic moment. The decrease in magnetization for x>0.5 obeys the Yafet–Kittel (Y–K) model. The increase in Y–K angles for x≥0.5 indicates the increased favor for triangle spin arrangements on B-sites. This suggests the existence of canted spin structure in the ferrite system with higher content of Mn. Hystersis loops were measured. The initial permeability μ_i was measured as a function of temperature.     

Substitutional effect of Cr ions on the properties of Mg–Zn ferrite nanoparticles

The effect of Cr³⁺ substitution in Mg–Zn ferrite, with a chemical formula Mg_0.5Zn_0.5Cr_xFe_2−xO₄ (x=0.0–1.0), synthesized by a sol–gel auto-combustion reaction is presented in this paper. The resultant powders were investigated by various techniques, including X-ray diffractometry (XRD), transmission electron microscopy (TEM), infrared spectroscopy (IR), vibrating sample magnetometry (VSM), and DC resistivity. The XRD pattern revealed that the cubic spinel structure is maintained for the all the compositions. The particle sizes measured from XRD and TEM are in good agreement with each other. The cation distribution suggests that Mg²⁺, Cr³⁺ and Fe³⁺ have strong preference towards octahedral B-site. The theoretical lattice constant and experimental lattice constant match each other very well. The IR analysis supports the presently accepted cation distribution. The saturation magnetization decreases linearly with increasing Cr³⁺ content. Curie temperatures are obtained by the Laoria and AC susceptibility techniques. The dc resistivity has been investigated as a function of temperature and composition.     

The magnesium doping effect of the vanadate spinel MnV2O4

We investigate the structural, transport, and magnetic properties of Mn_1−xMg_xV₂O₄(0≤x≤0.8) to study the role of the A-site magnetism in vanadate spinels. With increasing Mg²⁺ concentration, the lattice parameters shrink and the hopping energy for electrons increases, whereas both the magnetic transition temperature and the structural transition temperature decrease gradually. The two temperatures become closer and eventually equal to each other at x=0.2. For x>0.2 the first order transition disappears and the magnetic ground state switches from a long range ordered ferrimagnetic state to a glassy state. The transition temperature of the glassy state continues to decrease with further increase of Mg content, which is attributed to the dilution in the magnetism on A sites.     

Structural and magnetic investigations of sub-nano Mn-Mg ferrite prepared by wet method

Manganese-magnesium ferrite nanoparticles Mn_1−xMg_xFe₂O₄; 0≤x≤0.25 were prepared by the co-precipitation route. The samples were characterized by X-ray diffraction (XRD), which confirms the single phase spinel structure. Crystallite size, calculated from the (3 1 1) peak using the Scherrer formula, was found to increase with increasing Mg²⁺ concentrations and was found to be within the range 3-6 nm. TEM was also used to characterize the microstructure of nanosized Mn_1−xMg_xFe₂O₄. Nominal composition of the samples was determined by Atomic Absorption analysis (AA). Hysteresis loops of manganese-magnesium ferrite were obtained at room temperature and revealed lower saturation magnetization values associated with nanocrystalline Mn_1−xMg_xFe₂O₄ particles. This behavior was attributed to structural distortion of surface spins compared to that of the bulk one.     

Temperature and composition dependence of magnetic properties of cobalt–chromium co-substituted magnesium ferrite nanomaterials

The temperature and composition dependence of magnetic properties of Co–Cr co-substituted magnesium ferrite, Mg_1−xCo_xCr_xFe_2−xO₄ (x=0.0–0.5), prepared by novel polyethylene glycol assisted microemulsion method, are studied. The synthesized materials are characterized by the Mössbauer spectrometer and standard magnetic measurements. Major hysteresis loops are measured up to the magnetic field of 50 kOe at 300, 200 and 100 K. The high field regimes of these loops are modeled using the Law of Approach to saturation to determine the first-order cubic anisotropy coefficient and saturation magnetization. Both the saturation magnetization and the anisotropy coefficient are observed to increase with the decrease in temperature for all Co–Cr co-substitution levels. Also, both the saturation magnetization and the anisotropy coefficient achieved maximum value at x=0.3 and x=0.2, respectively. Explanation of the observed behavior is proposed in terms of the site occupancy of the co-substituent, Co²⁺ and Cr³⁺ in the cubic spinel lattice.     

Spectral studies of Co substituted Ni-Zn ferrites

The spinel ferrites Zn_0.35Ni_0.65−xCo_xFe₂O₄, 0≤x≤1, have been prepared using the standard ceramic technique. Room temperature Mössbauer, X-ray and infrared IR spectra were used for carrying out this study. X-ray patterns reveal that all the samples have single-phase cubic spinel structure. The Mössbauer spectra of the samples show a paramagnetic phase for x=0 and a six-line magnetic pattern and a central paramagnetic phase for x≥0.1. They are analyzed and attributed to two magnetic subpatterns and two quadrupole doublets due to Fe³⁺ ions at the tetrahedral A-sites and octahedral B-sites. Four absorption bands are observed in IR spectra. They confirm the spinel structure of the samples and existence of Fe³⁺ ions in the sample sublattices. The deduced hyperfine interactions, lattice parameters, absorption band positions and intensities and force constant are found to be dependent on the substitution factor x, where the cation distribution is estimated. The hyperfine magnetic fields, magnetization and lattice resonant frequency are found to be dependent on the interionic distance.     

Structure, transport and magnetic properties in La2xSr2−2xCo2xRu2−2xO6

The perovskite solid solutions of the type La_2xSr_2−2xCo_2xRu_2−2xO₆ with 0.25≤x≤0.75 have been investigated for their structural, magnetic and transport properties. All the compounds crystallize in double perovskite structure. The magnetization measurements indicate a complex magnetic ground state with strong competition between ferromagnetic and antiferromagnetic interactions. Resistivity of the compounds is in confirmation with hopping conduction behaviour though differences are noted especially for x=0.4 and 0.6. Most importantly, low field (50 Oe) magnetization measurements display negative magnetization during the zero field cooled cycle. X-ray photoelectron spectroscopy measurements indicate the presence of Co²⁺/Co³⁺ and Ru⁴⁺/Ru⁵⁺ redox couples in all compositions except x=0.5. Presence of magnetic ions like Ru⁴⁺ and Co³⁺ gives rise to additional ferromagnetic (Ru-rich) and antiferromagnetic sublattices and also explains the observed negative magnetization.     

Magnetic ordering in Ni–Cd ferrite

A series of Ni_1−xCd_xFe₂O₄ (0.0≤x≤0.8) were prepared by conventional double sintering ceramic method and sintered at 1200 °C for 6 h. X-ray diffraction results confirmed the single-phase spinel structures of all the samples. The Curie temperature decreases linearly with increasing Cd content, which is explained due to the weakening of the A–B exchange interaction. The sample with x=0.7 shows re-entrant type of spin glass phase transitions. The magnetic moment and saturation magnetization at 20 K are found to increase with Cd content up to x=0.5 and then tends to decrease for x>0.5. The increase in magnetic moment with cadmium is attributed to Neel's two sublattice (A- and B-sublattice) collinear models according to which the magnetic moment is the vector sum of the lattice magnetic moment. The decrease in magnetization for x>0.5 obeys the Yafet–Kittel (Y–K) model. The increase in Y–K angles for x>0.3 indicates the increased tendency for triangular spin arrangements on B-sites. This suggests the existence of a canted spin structure in the ferrite system with higher content of Cd.     

Improvement in magnetic properties of La substituted BaFe12O19 particles prepared with an unusually low Fe/Ba molar ratio

In this study, effect of lanthanum substitution on the phase composition, lattice parameters and magnetic properties of barium hexaferrite has been studied in samples synthesized in ammonium nitrate melt. Samples, prepared with different lanthanum amount and having various initial Fe/(Ba+La) ratios in between 12 and 2 {(Ba_1−xLa_x)·n Fe₂O₃, where 0≤x≤1 and 1≤n≤6)}, are sintered at temperatures from 800 to 1200 °C. The lattice parameters, both a and c, decreases with increasing La amount which results in a decrease of the unit cell volume. The scanning electron microscope micrographs show that the pure and La-substituted sample with x=0.3, both calcinated at 1000 °C, have grain sizes smaller than 1 μm. The coercivities of the La-substituted samples increase with increasing La amount and reaches to a maximum value of 5.73 kOe, when x=0.3. Sintering at higher temperatures (above 1000 °C) decreases the coercivity, resembling a transition from single to multi-domain behavior of the particles, while saturation magnetization of the samples continues to increase due to the increasing grain size. Magnetization measurements of the samples prepared with different Fe/(Ba+La) molar ratios, n's, revealed that the specific saturation magnetization slightly increases with decreasing n, while coercivities fluctuates around 5.5 kOe. However, a sharp increase in the saturation magnetization has been observed in the sample having n=1 and washed in HCl. It was measured as 59.2 emu/g at 15 kOe, which is higher than that of the pure sample (57.5 emu/g). Thus, the magnetic parameters are optimized in the sample Ba_0.7La_0.3Fe₁₂O₁₉ so as to maximize both coercivity and specific saturation magnetization in the HCl-washed sample synthesized by starting with an unusually low Fe/(Ba+La) molar ratio of 2 (or n=1).     

Influence of manganese substitution and annealing temperature on the formation,microstructure and magnetic properties of Mn–Zn ferrites

The effects of annealing temperature and manganese substitution on the formation, microstructure and magnetic properties of Mn_xZn_1−xFe₂O₄ (with x varying from 0.3 to 0.9) through a solid-state method have been investigated. The correlation of the microstructure and the grain size with the magnetic properties of Mn–Zn ferrite powders was also reported. X-ray diffraction (XRD), a scanning electron microscope (SEM) and a vibrating sample magnetometer (VSM) were utilized in order to study the effect of variation of manganese substitution and its impact on crystal structure, crystalline size, microstructure and magnetic properties of the ferrite powders formed. The XRD analysis showed that pure single phases of Mn–Zn ferrites were obtained by increasing the annealing temperature to 1200–1300 °C. Increasing the annealing temperature to ?1300 °C led to abnormal grain growth with inter-granular pores and this led to a decrease in the saturation magnetization. Moreover, an increase in the Mn²⁺ ion substitution up to x=0.8 increased the lattice parameter of the formed powders due to the high ionic radii of the Mn²⁺ ion. Mn–Zn ferrites phases were formed and the positions of peaks were shifted by substituting manganese. The average crystalline size was increased by increasing the annealing temperature and decreased by increasing the substitution by manganese up to 0.8. The average crystalline size was in the range 95–137.3 nm. The saturation magnetization of the Mn–Zn-substituted ferrite powders increased continuously with an increase in the Mn concentration up to 0.8 at annealing temperatures of 1200–1300 °C. Further increase of Mn substitution up to 0.9 led to a decrease of saturation magnetization. The saturation magnetization increased from 17.3 emu/g for the Mn_0.3Zn_0.7Fe₂O₄ phase particles produced to 59.08 emu/g for Mn_0.8Mn_0.2Fe₂O₄ particles.     

Structure,analysis and some magnetic properties for low temperature fired Ni–Cu ferrite

Cu²⁺ ions substituted Ni-ferrite having the general formula Ni_1-xCu_xFe₂O₄ (where x=0.0, 0.2, 0.4 and 0.6) were prepared by the sintering ceramic method. X-ray diffraction, infrared spectra and magnetization of the above ferrite were carried out to investigate structural and magnetic characterization of this ferrite. Crystallite size, lattice parameters, positional oxygen parameter and ionic radii for both tetrahedral and octahedral sites were calculated. The experimental lattice parameter was found to vary between 8.3856 and 8.3865 Å. The infrared spectra were measured in the frequency range 650–150 cm⁻¹. Two prominent bands were observed, high frequency band ν₁ and low frequency band ν₂ were assigned to tetrahedral and octahedral sites. Bond length and force constant were also calculated for both tetrahedral and octahedral sites. The effect of Cu concentration on, saturation magnetization, coercivity ratio and magnetic moment were investigated using vibrating sample magnetometer (VSM). It was found that both saturation magnetization (M_S) and coercivity (H_c) decreases with increasing in Cu content.     

Physical and magnetic properties of highly aluminum doped strontium ferrite nanoparticles prepared by auto-combustion route

Highly Al³⁺ ion doped nanocrystalline SrFe_12−xAl_xO₁₉ (0≤x≤12), were prepared by the auto-combustion method and heat treated in air at 1100 °C for 12 h. The phase identification of the powders performed using x-ray diffraction show presence of high-purity hexaferrite phase and absence of any secondary phases. With Al³⁺ doping, the lattice parameters decrease due to smaller Al³⁺ ion replacing Fe³⁺ ions. Morphological analysis performed using transmission electron microscope show growth of needle shaped ferrites with high aspect ratio at Al³⁺ ion content exceeding x≥2. Al³⁺ substitution modifies saturation magnetization (M_S) and coercivity (H_C). The room temperature M_S values continuously reduced while H_C value increased to a maximum value of 18,100 Oe at x=4, which is an unprecedented increase (∼321%) in the coercivity as compared to pure Sr-Ferrite. However, at higher Al³⁺ content x>4, a decline in magnetization and coercivity has been observed. The magnetic results indicate that the best results for applications of this ferrite will be obtained with an iron deficiency in the stoichiometric formulation.     

The magnetic behavior of La1−xTbxMn2Si2 (0≤x≤0.3) in weak magnetic fields

The structure and magnetic properties of La_1−xTb_xMn₂Si₂ (0≤x≤0.3) were studied by X-ray powder diffraction and DC magnetization measurements. All the compounds crystallize in ThCr₂Si₂-type structure. Substitution of Tb for La led to a linear decrease in the lattice constants and the unit-cell volume. A ferromagnetic phase for x≤0.15, and an antiferromagnetic phase for x=0.3 have been observed at about room temperature, whereas the compounds with x=0.2 and 0.25 exhibit a magnetic phase transition from ferromagnetism to antiferromagnetism.     

Effect of Sr concentration on microstructure and magnetic properties of (Ba1−xSrx)(Ti0.3Fe0.7)O3 ceramics

Fe-doped (Ba_1−xSr_x)TiO₃ ceramics were prepared by solid-state reaction, and ferromagnetism was realized at room temperature. The microstructure and magnetism were modified by the Sr concentration control (0≤x≤75 at%) at a fixed Fe concentration, and the relevant magnetic exchange mechanism was discussed. All the samples are shown to have a single perovskite structure. When increasing the Sr concentration, the phase structure is transformed from a hexagonal perovskite into a cubic perovskite, with a monotonic decrease in lattice parameters induced by ionic size effect. The room-temperature ferromagnetism is expected to originate from the super-exchange interactions between Fe³⁺ on pentahedral and octahedral Ti sites mediated by the O²⁻ ions. The increase in Sr addition modifies two main influencing factors in magnetic properties: the ratio of pentahedral to octahedral Fe³⁺ and the concentration of oxygen vacancies, leading to a gradually enhanced saturation magnetization. The highest value, obtained for Fe-doped (Ba_0.25Sr_0.75)TiO₃, is an order of magnitude higher than that of the Fe-doped BaTiO₃ system with similar Fe concentration and preparation conditions, which may indicate (Ba_1−xSr_x)TiO₃ as a more suitable matrix material for multiferroic research.     

Could Mg content control the conduction mechanism of Ba Co Zn-W-type hexagonal ferrites?

Electrical properties as a function of composition, frequency and temperature for a series of W-type hexagonal ferrites with the general formula BaCoZn_1−xMg_xFe₁₆O₂₇; 0≤x≤0.6 prepared using the conventional ceramic method were studied. These samples are semiconductor-like materials, where the ac conductivity increases with increasing temperature. The results show that the conduction mechanism depends on the Mg²⁺ substitution. The transition temperature (T_σ) increases with increasing Mg content and gives a hump at x=0.5; after that T_σ decreases again. Both the ac conductivity and dielectric constant vary with Mg content and reach the highest value at x=0.5, due to the highest value of the ratio of Fe²⁺/Fe³⁺ at x=0.5. The peak value of the dielectric constant depends on the Mg content x.     

Influence of V substitution for Fe on the transport and magnetic properties of Sr2FeMoO6

We have investigated the crystal structure, magnetization and magnetoresistance of the double perovskite compounds Sr₂(Fe_1−xV_x)MoO₆ (0≤x≤0.1). The lattice constants and the cation ordering decrease monotonously with the V content. The Curie temperature, saturation magnetization and low field magnetoresistance of the compounds decrease with increasing x due to the reduced degree of ordering. The resistivity of Sr₂FeMoO₆ and lightly doped samples shows semiconductive behavior, while the samples with higher doping levels exhibit a semiconductor-metal transition around 80 K.     

Electronic structure and magnetic and electromagnetic wave absorption properties of BaFe12-xCoxO19 M-type hexaferrites

Crystal, electronic structures and the magnetic and electromagnetic wave absorption properties of BaFe_12-xCo_xO₁₉ (x = 0–2) M-type hexaferrites prepared by a co-precipitation technique were studied. The analyses of X-ray diffraction patterns indicated that the samples mainly crystallized in the P6₃/mmc hexagonal structure, with the additional constitution of Y-type hexaferrite as x > 0. The replacement of Co²⁺ for Fe³⁺ in BaFe_12-xCo_xO₁₉ changed the lattice constants and caused lattice distortions. Particularly, Co²⁺ doping also reduced magnetization and hard magnetic property of BaFe_12-xCo_xO₁₉. This is ascribed to magnetic moment of Co²⁺ smaller than that of Fe³⁺ and to the decrease of magnetocrystalline anisotropy. Having studied electromagnetic wave absorption properties in the frequency range f = 0.1–18 GHz, we found BaFe_12-xCo_xO₁₉ showing high reflection loss (RL) values at frequencies of 0.1–15 GHz, but fairly low RL values at higher frequencies. These features suggest that BaFe_12-xCo_xO₁₉ can be suitable to electronic devices working at GHz frequencies.     

Structure and superconductivity of Mg1−xPbxB2

A series of polycrystalline samples of Mg_1−xPb_xB₂ (0≤x≤0.10) were prepared by a solid state reaction method and their structure, superconducting transition temperature and transport properties were investigated by means of X-ray diffraction (XRD) and resistivity measurements. Mg_1−xPb_xB₂ compounds were shown to adopt an isostructural AlB2-type hexagonal structure in a relatively small range of lead concentration, x≤0.01. The crystalline lattice constants were evaluated and were found to exhibit slight length compression as x increases. The superconducting transition temperature (T_c) steadily decreases with Pb doping. It is suggested that the mechanism of superconductivity reduction by lead doping can be attributed to the chemical pressure effect.     

Effect of Cu-Cr co-substitution on magnetic properties of nanocrystalline magnesium ferrite

This study deals with the temperature and composition dependence of magnetization and magnetic anisotropy of Cu²⁺-Cr³⁺ co-substituted magnesium ferrite, Mg_1−xCu_xCr_xFe_2−xO₄ (x=0.0-0.5). The synthesized materials are characterized using thermo gravimetric analysis, X-ray diffraction, scanning electron microscopy, energy dispersive X-ray fluorescence, Mössbauer spectrometer, superconducting quantum interference device magnetometer and vibrating sample magnetometer. The M-H loops measured up to 50 kOe at 300, 200 and 100 K, revealed narrow hysteresis curves with a coercive field and saturation magnetization varying for different compositions. The high field regimes of these loops are modeled using the Law of Approach to saturation to extract anisotropy information and saturation magnetization. Both the saturation magnetization and the anisotropy constant are observed to increase with the decrease in temperature while decrease with the Cu-Cr co-substituents for all the samples. Explanation of the observed behavior is proposed in terms of the preference of the co-substituent ions of Cu²⁺ and Cr³⁺ and their predominant choice to substitute into the octahedral sites of the cubic spinel lattice.