Soft-X-ray lasing in nickel-like barium at 9.2 nm using the grazing-incidence scheme

We report on the experimental demonstration of saturated X-ray lasing on the 4 d → 4p, J = 0–1 line of nickel-like barium (Ba, Z = 56) at a wavelength of 9.2 nm, using a main pulse energy of 9 J in a 1.5-ps duration pulse from a Nd:glass chirped-pulse amplification laser. Gain saturation was achieved by applying a triple-pulse scheme in which a weak (few-percent) prepulse, preceding the main pulse by 2.4 ns, is followed by a second, relatively intense (16%) prepulse ~ 50 ps before the main pulse. For handling convenience, compound targets of BaF₂ were used, either in the form of windows or coated onto glass slides.     

23.4nm软X射线多层膜反射镜研制

为了满足类氖-锗X射线激光研究的需要,设计制备了23.4 nm软X射线多层膜反射镜.依据多层膜选材原则并考虑材料的物理化学特性选择新的材料Ti与Si组成材料对.设计优化材料多层膜的周期厚度(d),材料比例(Γ),周期数(N),计算出Ti/Si反射率曲线.通过实验优化各种镀膜工艺参数,制备出了23.4 nm的Ti/Si多...     

Longitudinal coherence and spectral profile of a nickel-like silver transient soft X-ray laser

The spectral width of a Ni-like silver transient soft X-ray laser (4d-4p λ= 13.9 nm) was experimentally inferred from the measurement of its temporal coherence, performed with a novel wavefront division interferometer. The measured coherence time of 3 ps corresponds to a spectral linewidth of 0.7 m? which is narrow. We compare this experimental result to numerical simulations of the amplified line profile, performed along two different approaches. Both calculations predict a spectral linewidth that is about 3 times larger than the experimental value. We discuss several effects that might explain this discrepancy. We show that, due to the short duration of the X-ray laser pulse, the assumption of a stationary electromagnetic field used in both the experimental analysis and in the calculations need to be reconsidered.     

Saturated X-ray lasing in Ni-like Sn at 11.9 nm using the GRIP scheme

We report on gain-saturated operation of the 11.9 nm X-ray lasing line in Ni-like Sn using the grazing-incidence pumping scheme (GRIP). The experiments were done with 2-ps duration pump pulses and energies up to 5 J. Strong gain saturation with multi-microjoule output was measured for the Sn laser at a grazing angle of 30° and a pump pulse energy of 3 J. This was achieved with a 4.5%, 2-ps duration prepulse 2.4 ns ahead of the main pulse and also incident at grazing incidence. Increasing laser output was observed at GRIP angles up to 45°. At this angle, the minimum energy required for saturated lasing was determined as ∼2 J.     

Highly directive 18.9 nm nickel-like molybdenum x-ray laser operating at 150 mJ pump energy

We experimentally demonstrate that by longitudinally pumping 2 mm long molybdenum preformed plasma with high-intensity 475 fs duration laser pulse, a highly directive soft-x-ray laser at 18.9 nm wavelength is generated. The divergence of the beam is evaluated to be of the submilliradian order, and only requires a pump laser energy of 150 mJ.     

Collisional excitation soft X-ray laser at 23.6 nm in a laser-produced cylindrical target

We have tested soft X-ray lasing in neon-like germanium with cylindrical targets where wave guiding and plasma confinement may affect lasing. An intense soft X-ray laser beam of 0.05 MW peak power and a narrow beam divergence (8 mrad) was produced at 23.6 nm with a 4 cm long straight cylindrical target of 0.72 mm inner diameter. Bending the cylindrical target to form a toroidal shape increased the lasing intensity by a factor of 3 accompanied with reduction of the beam divergence from 8 to 6 mrad.     

Saturated amplification of a collisionally pumped optical-field-ionization soft X-ray laser at 41.8 nm

We report the first saturated amplification of an optical-field-ionization soft x-ray laser. The amplifying medium is generated by focusing a circularly polarized 330-mJ, 35-fs, 10-Hz Ti:sapphire laser system in a few-mm cell filled with xenon. A gain of 67 cm(-1) on the 4d(9)5p-4d(9)5d transition at 41.8 nm in Pd-like xenon and a gain-length product of 15 have been inferred at saturation. This source delivers about 5 x 10(9) photons per pulse. The influence of the pumping energy and the laser polarization on the lasing output are also presented.     

Efficient J=0-1 soft-X-ray lasing in neon-like ions at pump powers below 250 GW

2 . By using a 0.7% prepulse that precedes the main pulse by 5 ns and applying a total pump energy of 100 J or less, the J=0-1 lasing is at least one order of magnitude higher than the non-lasing background. For the 32.6-nm line of Ti, the 25.5-nm line of Fe, and the 23.1-nm line of Ni, gain coefficients of (±) 4.20.4cm^-1, (±) 3.90.3cm^-1, and (±) 3.60.6cm^-1, respectively, were measured for 2.4-cm-long curved targets, resulting in gain–length products of ∼10. Angle-resolved spectra indicate a beam divergence of 3 mrad (FWHM), typically. The space-resolved spectra show that the J=0-1 lasing lines are emitted from an approximately 60-μm-wide (FWHM) plasma region, whereas the nearby continuum emission is produced in a considerably broader plasma region of ∼250 μm. Lasing at 25.5 nm in neon-like iron was observed at a pump power as low as 180 GW (∼9 TW/cm²), with, however, considerable shot-to-shot scatter in the absolute laser output. Received: 5 September 1997/Revised version: 10 November 1997     

激光等离子体软X光源8—20nm光谱辐射研究

研制了了一种脉冲重复频率为１０Ｈｚ的激光等离子软Ｘ射线源；傅波长０．５３μｍ和波长１．０６μｍ的激光脉冲，聚焦在不同的金属靶上，使之离子化。     

Intensity distribution of a capillary-discharge 46.9 nm soft X-ray laser

We realize a Ne-like Ar 46.9 nm soft X-ray laser pumped by a capillary discharge. The study of the laserpulse-intensity distribution is important for applications of soft X-ray lasers. The intensity distribution demonstrates the gain distribution, plasma radius, and axial plasma density that contribute to the study of the laser-pulse formation. To measure the intensity in different positions of the X-ray laser spot, we moved transversally an X-ray diode (XRD) assembled with a slit. We obtain the onedimensional intensity distribution. We find a laser divergence (FWHM) of 4.0 mrad. According to the gain-guided model, we calculate the intensity distribution. The measured divergence of 4.0 mrad roughly corresponds to a plasma radius a approximately equal to 230–250 μm and on-axis electron density n _e ≈ 8.0?10¹⁸ ?9.0?10¹⁸ cm ^?3. The results of calculations indicate that the divergence of the intensity distribution increases when the plasma radius decreases and the on-axis electron density increases.     

Capillary discharge soft X-ray lasing in Ne-like Ar pumped by low main current pulses

Under the condition of the low main current pulse, the capillary discharge soft X-ray laser is obtained. The laser energy of the same discharge current amplitude at different Ar pressures and of different current amplitudes at the same Ar pressure are compared, respectively. At different Ar pressures, the amplitude of the main current pulse evidently impacts the soft X ray, especially at a pressure higher than 30 Pa. In order to obtain the laser output at a high Ar pressure, the amplitude should be increased. However, at the same Ar pressure, it might have an optimum current, in which case the laser spike is the highest and the most stationary. The laser achieving time at different amplitudes is also discussed. As far as we know, this is the first time the influence of the amplitude of the main current pulse has been analyzed.     

13.9 nm马赫贞德干涉仪用软X射线分束镜研究

 介绍了13.9 nm马赫贞德干涉仪用软X射线分束镜的设计、制备与性能检测。基于分束镜反射率和透过率乘积最大的评价标准,设计了13.9 nm软X射线激光干涉实验用多层膜分束镜。采用磁控溅射方法在有效面积为10 mm×10 mm、厚度为100 nm的Si3N4基底上镀制了Mo/Si多层膜,制成了多层膜分束镜。利用X射线掠入射衍射的方法测量了Mo/Si多层膜的周期。用扩束He-Ne激光束进行的投影成像方法定性分析了分束镜的面形精度,利用光学轮廓仪完成了分束镜面形精确测量。利用北京同步辐射装置测量了分束镜反射率和透射率,在13.9 nm处,分束镜反射率和透过率乘积达4%。使用多层膜分束镜构建了软X射线马赫贞德干涉仪,并应用于13.9 nm软X射线激光干涉实验中,获得了清晰的含有C8H8等离子体电子密度信息的动态干涉条纹。     

13.9 nm马赫贞德干涉仪用软X射线分束镜研究

介绍了13.9 nm马赫贞德干涉仪用软X射线分束镜的设计、制备与性能检测。基于分束镜反射率和透过率乘积最大的评价标准,设计了13.9 nm软X射线激光干涉实验用多层膜分束镜。采用磁控溅射方法在有效面积为10 mm×10 mm、厚度为100 nm的Si3N4基底上镀制了Mo/Si多层膜,制成了多层膜分束镜。利用X射线掠入射衍射的方法测量了Mo/Si多层膜的周期。用扩束He-Ne激光束进行的投影成像方法定性分析了分束镜的面形精度,利用光学轮廓仪完成了分束镜面形精确测量。利用北京同步辐射装置测量了分束镜反射率和透射率,在13.9 nm处,分束镜反射率和透过率乘积达4%。使用多层膜分束镜构建了软X射线马赫贞德干涉仪,并应用于13.9 nm软X射线激光干涉实验中,获得了清晰的含有C8H8等离子体电子密度信息的动态干涉条纹。     

Review of collisional excitation neon-like and nickel-like soft X-ray lasers pumped by multiple infrared laser pulses at the Institute of Laser Engineering,Osaka University

We report on the soft X-ray laser developments performed at the Institute of Laser Engineering, Osaka University especially for the collisional excitation X-ray lasers at wavelengths between 25 nm and 4 nm. The performance of neon-like and nickel-like ion X-ray lasing pumped by a train of short laser pulses has been investigated. We have also demonstrated double pass amplification using a soft X-ray multi-layer mirror at wavelengths of 19.6 nm and 7.9 nm. Based on these results and experimental technique, two targets were placed in series to double the gain length. Two opposing laser beams irradiated the double targets with a suitable time difference for quasi-traveling wave pumping. The double target amplification was successfully demonstrated with two beam irradiation for Ag, Nd, Yb, Hf and Ta lasing. The estimated absolute photon flux from the saturated amplification Ag X-ray laser was ∼300 μJ. Based on the experimental results, we also discuss the applications of an X-ray laser as a super-high brightness soft X-ray source.     

High-resolution spectrum of xenon ions at 13.4 nm

The spectrum of xenon excited in a low-inductance vacuum spark was photographed at high resolution in the region of 9.5-15.5 nm. The observed transitions were identified as belonging to ions from Xe8+ to Xe13+. In the region of importance for extreme-ultraviolet lithography around 13.4 nm, the strongest lines were identified as 4d8-4d7 5p transitions in Xe10+. The identifications were made by use of energy parameters extrapolated along the isoelectronic sequence.     

Statistical investigations of the beam stability of the double-pass amplified zinc soft X-ray laser at 21.2 nm

At the Prague asterix laser system (PALS) of the Academy of Sciences of the Czech Republic the 1-TW asterix iodine laser is used as a pump source for soft X-ray laser experiments. The prepulse technique was applied which is known to enhance the X-ray laser output at the J=0-1 transition dramatically. Since Zn slab targets were used the laser wavelength was 21.2 nm. A prepulse beam having 1.6 J was preceding the main pulse by 10 ns. The main and the prepulse beam are focused by two different optical systems separately. Implementing a half-cavity set-up for double-pass amplification using a Mo/Si multilayer mirror the X-ray laser output was 10 times stronger than at single pass amplification in a 3-cm long plasma. Double-pass amplification was observed to be most efficient when the pump pulse duration was at least 120 ps longer than the round trip time in the half-cavity. Under this fundamental condition the X-ray laser reached saturation in the double-pass regime containing 4 mJ energy what is proved to be enough for applications. In this contribution the X-ray laser features like divergence in two dimensions, the beam quality (symmetry), the pointing angle and the time-integrated output energy are investigated over more than 100 shots. To characterize the stability of the X-ray laser the shot distribution, the mean value and the standard deviation for these parameters are evaluated. For 18 shots in a series -- achieved during one single day -- the corresponding values are given and detailed chi-squared tests characterize the Zn X-ray laser as a robust tool suitable for applications. At PALS soft X-ray laser beam time can be reserved for external research groups.Received: 16 April 2003, Published online: 5 August 2003PACS: 42.55.Vc X- and -ray lasers - 42.60.Da Resonators, cavities, amplifiers, arrays, and rings - 42.60.Jf Beam characteristics: profile, intensity, and power; spatial pattern formation     

Transient collisionally excited X-ray laser in nickel-like zirconium pumped with the PHELIX laser facility

A transient collisionally excited X-ray laser has been put into operation using the front end of the PHELIX laser system as a pump laser. Strong lasing at 22 nm has been observed in nickel-like zirconium. PACS 42.60.-v; 42.55.Vc; 42.62.Fi     

Prepulse dependence ofJ=0−1 lasing at 32.6 nm in neon-like titanium

The dependence of the intensity of the 3p—3s,J = 0–1 lasing line at 32.6 nm in neon-like titanium on the prepulse level has been investigated experimentally. Titanium slabs were irradiated with 1.315 µm/450 ps pulses from the Asterix IV iodine laser using a defined prepulse of 5.2 ns before the main pulse. It is found that for pump energies close to the minimum energy for which lasing is observed, a prepulse level of order 0.5% gives the highest XUV laser intensity, whereas a higher prepulse level, of order 10% and more, is required for optimum XUV lasing far above the threshold. For a 2.7 cm long titanium target lasing was observed down to a pump irradiance of 2.5 TW/cm² (50 J/450 ps) for the 0.5% prepulse.