Towards free-standing graphene/carbon nanotube composite films via acetylene-assisted thermolysis of organocobalt functionalized graphene sheets

A novel approach towards highly conductive free-standing chemically reduced graphene/carbon nanotube composite films via an in situ thermolysis of functionalized graphene/organic cobalt complexes was developed. By combining 1D-CNT and 2D-graphene, a synergistic effect of conductivity was established.     

Hydrous manganese oxide/carbon nanotube composite electrodes for electrochemical capacitors

A novel type of composite electrode based on hydrous manganese oxide and a single-walled carbon nanotube has been prepared and used in electrochemical capacitors. Cyclic voltammetry, galvanostatic charging/discharging tests and electrochemical impedance measurements were applied to investigate the performance of the composite electrodes with different ratios of hydrous manganese oxide and single-walled carbon nanotube. For comparison, the performance of pure hydrous manganese oxide and pure carbon nanotubes was also studied. In this way, the composite electrode with a 6:4 ratio of hydrous manganese oxide to carbon nanotube was found to be the most promising active material for an electrochemical capacitor, which shows both good capacitance and power characteristics.     

硒/氧化石墨烯/二氧化钛复合薄膜的制备及光电转换性质

将氧化石墨烯(GO)掺入钛酸溶胶中,以导电玻璃(ITO)为基底,经浸渍-涂覆-煅烧得到GO/TiO2复合薄膜;采用电沉积技术在GO/TiO2薄膜表面沉积Se纳米微粒,得到Se/GO/TiO2复合薄膜;利用扫描电子显微镜和X射线衍射仪分析了复合薄膜的形貌和晶体结构,采用紫外可见光谱仪测定了其光谱学性质,利用光电转换实验测定了其光电转换性质.结果表明,所制备的Se/GO/TiO2复合薄膜各组分分布均匀,具有锐钛矿相结构的TiO2颗粒粒径为20nm,与TiO2结合的GO具有分散片层结构,薄膜中的Se颗粒粒径为60～80nm.与此同时,在Se和GO的共同作用下,Se/GO/TiO2复合薄膜对可见光有很好的光电转换效应.     

Design and tailoring of a three-dimensional reduced graphene oxide/helical carbon nanotube composite for electrochemical biosensing application

Journal of Solid State Electrochemistry - Herein, three-dimensional reduced graphene oxide/helical carbon nanotubes (RGO/HCNTs) nanocomposites were synthesized by a combined solution-based method...     

Facile preparation of highly conductive,flexible, and strong carbon nanotube/polyaniline composite films

In general, the high electrical conductivity (EC) comes into conflict with the good flexibility and high strength of carbon nanotube (CNT)/polyaniline (PANI) composites. In other words, a high CNT content will bring about a high EC but lead to a low flexibility and strength due to the CNT‐constrained matrix deformation and CNT aggregation. In this work, a highly conductive, flexible and strong CNT/PANI composite film prepared via a facile solvent‐evaporation method is readily obtained by a cold stretching. The cold stretching is conducted at room temperature for the CNT/PANI film. It is observed that the cold stretching process leads to an unexpectedly enhanced EC. The as‐obtained EC of 231 S/cm is much higher than that (2 – 50 S/cm) of the previously reported CNT/PANI composite films. Meanwhile, the strength is obviously improved over that of the pure PANI film and the good flexibility is maintained to a high degree by the introduction of a proper CNT content. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1575–1585     

Poly(malachite green) at nafion doped multi-walled carbon nanotube composite film for simple aliphatic alcohols sensor

Conductive composite film which contains nafion (NF) doped multi-walled carbon nanotubes (MWCNTs) along with the incorporation of poly(malachite green) (PMG) has been synthesized on glassy carbon electrode (GCE), gold and indium tin oxide (ITO) electrodes by potentiostatic methods. The presence of MWCNTs in the composite film (MWCNTs-NF-PMG) enhances surface coverage concentration (Γ) of PMG to ≈396%, and increases the electron transfer rate constant (k_s) to ≈305%. Similarly, electrochemical quartz crystal microbalance study reveals the enhancement in the deposition of PMG at MWCNTs-NF film. The surface morphology of the composite film deposited on ITO electrode has been studied using scanning electron microscopy (SEM) and scanning tunneling microscopy (STM). These two techniques reveal that the PMG incorporated on MWCNTs-NF film. The MWCNTs-NF-PMG composite film also exhibits promising enhanced electrocatalytic activity towards the simple aliphatic alcohols such as methanol, ethanol and propanol. The electroanalytical responses of analytes at NF-PMG and MWCNTs-NF-PMG films were measured using both cyclic voltammetry (CV) and differential pulse voltammetry (DPV). From electroanalytical studies, well defined voltammetric peaks have been obtained at MWCNTs-NF-PMG composite film for methanol, ethanol and propanol at Epa = 609, 614 and 602 mV respectively. The sensitivity of MWCNTs-NF-PMG composite film towards methanol, ethanol and propanol in CV technique are 0.59, 0.36 and 0.92 μA mM⁻¹ cm⁻² respectively, which are higher than NF-PMG film. Further, the sensitivity values obtained using DPV are higher than the values obtained using CV technique.     

Photo-oxidation behaviour of polyethylene/multi-wall carbon nanotube composite films

The resistance to accelerated photo-oxidation of polyethylene/multi-walled carbon nanotubes (MW-CNTs) composite films was compared with the photo-oxidation behaviour of pristine polyethylene film. The polyethylene/MW-CNTs films containing different CNTs loading were subjected to accelerated UV-B exposure. At short exposure time, i.e. under 200 h, the rates of carbonyl formation are very similar to that observed for pristine polyethylene film but at longer irradiation times the carbonyl formation increases for lower MW-CNTs contents (0.1, 0.2 and 0.5% wt./wt.), and decreases for higher MW-CNTs contents (1 and 2% wt./wt.). By adding a UV-stabilizer to the films their photo-oxidation rates are drastically decreased also at low MW-CNTs concentration. Addition of a metal deactivator (MD) produced no observable effect.     

Glass transition of polymer/single-walled carbon nanotube composite films

The glass-transition temperatures (T_g's) of nanocomposites of polystyrene (PS) and single-walled carbon nanotubes were measured in the bulk and in thin films with differential scanning calorimetry and spectroscopic ellipsometry, respectively. The bulk T_g of the nanocomposites increased by approximately 3 °C and became much broader than that of PS. For the nanocomposite films thinner than 45 nm, T_g decreased with decreasing film thickness [i.e., ΔT_g(nano) < 0]. This phenomenon also occurred in thin PS films, the magnitude of the depression in PS [ΔT_g(PS)] being somewhat larger. The film thickness dependence and the differences in the magnitude of ΔT_g in the two systems were examined in light of current theory, and a quantitative comparison was made. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3339–3345, 2003     

Amorphous carbon-linked TiO_2/carbon nanotube film composite with enhanced photocatalytic performance:The effect of interface contact and hydrophilicity

Carbon nanotube film(CNTF) can be used for photocatalysis and water treatment due to its porous structure,good stability and excellent electrical properties.In this work,TiO_2/amorphous carbon/carbon nanotube film(TCC) composite with uniform structure was prepared by a simple atomization spraying method.Rhodamine B(RhB) was used to test the photocatalytic activity of TCC.TCC composite exhibits good photocatalytic activity under ultraviolet light.In particular,the degradation efficiency of rhodamine B(RhB) by TCC sprayed with 9 layers of TiO_2(9 TCC) increased by 1.45 times than of TiO_2 under ultraviolet light.The enhanced photocatalytic activity of TCC is attributed to the CNTF,which can broaden the light response range of TCC and improve the migration efficiency of electrons.The existence of amorphous carbon will promote these advances.Moreover,the better hydrophilic properties would enhance the catalytic performance happened on the solid-liquid interface.Finally,the photocatalytic mechanism and degradation intermediates of the TCC composite were proposed.     

半导体/石墨烯复合光催化剂的制备及应用

首先分析了石墨烯和半导体光催化剂的特点,以及二者复合后可能具有的优越性质,接着介绍了石墨烯和半导体复合光催化剂的制备方法,归纳了石墨烯增强半导体光催化的机理,然后阐述了复合光催化剂在降解有机污染物、光催化分解水产氢、光催化还原CO2制有机燃料和光催化灭菌四个典型的应用,最后对半导体/石墨烯复合光催化剂未来的发展趋势提出了展望.     

Synthesis of iron oxide cubes/reduced graphene oxide composite and its enhanced lithium storage performance

Fe₃O₄ is considered as a promising electrode material for lithium-ion batteries(LIBs) due to its low cost and high theoretical capacity(928 mAh/g).Nevertheless,the huge volume expansion and poor conductivity seriously hamper its practical applications.In this study,we use a facile hydrothermal reaction together with a post heat treatment to construct the three-dimensional heterostructured composite(Fe₃O₄/rGO) inwhich reduced graphene oxide sheets wraped the Fe₃O₄ submicron cubes as the conductive network.The electric conduction and electrode kinetics of lithium ion insertion/extraction reaction of the composite is enhanced due to the assist of conductive rGO,and thus the Listorage performance is obviously improved.The composite exhibits a reversible charge capacity of772.1 mAh/g at the current density of 0.1 A/g,and the capacity retention reaches 70.3% after400 cycles at0.5 A/g,demonstrating obviously higher specific capacity and rate capability over the Fe₃O₄ submicron cubes without rGO,and much superior cycling stability to the parent Fe_2 O_3 submicron cubes without rGO.On the other hand,as a synergic conductive carbon support,the flexible rGO plays an important role in buffering the large volume change during the repeated discharge/charge cycling.     

Preparation and photochromic properties of pyrazolones/polyvinyl alcohol composite films

Novel photochromic composite films have been successfully fabricated by dispersing pyrazolone derivative:1,3-Diphenyl-4-(3-chlorobenzal)-5-hydroxypyrazole 4-phenylsemicarbazone (1a) into hydrosol of polyvinyl alcohol (PVA). The microstructure, photochromic behaviors and thermal bleaching properties were investigated by Raman spectroscopy, X-ray powder diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and ultraviolet-visible absorption spectroscopy (UV-vis). The results showed that 1a was not only blended but also well dispersed in the PVA polymer films with a suitable content of chromophore. Upon UV light irradiation, the composite films gradually changed from colorless to yellow and recovered fully to the initial state upon thermal bleaching. The time constants of photochromic reactions were almost the same as those of 1a observed in their crystalline state, indicating that the photochromic phenomenon is barely disturbed by the polymer matrix.     

Preparation of porous polyimide/in‐situ reduced graphene oxide composite films for electromagnetic interference shielding

Herein we report an easy and efficient approach to prepare lightweight porous polyimide (PI)/reduced graphene oxide (RGO) composite films. First, porous poly (amic acid) (PAA)/graphene oxide (GO) composite films were prepared via non‐solvent induced phase separation (NIPS) process. Afterwards PAA was converted into PI through thermal imidization and simultaneously GO dispersed in PAA matrix was in situ thermally reduced to RGO. The GO undergoing the same thermal treatment process as thermal imidization was characterized with thermogravimetric analysis, Raman spectra, X‐ray photoelectron spectroscopy and X‐ray diffraction to demonstrate that GO was in situ reduced during thermal imidization process. The resultant porous PI/RGO composite film (500‐µm thickness), which was prepared from pristine PAA/GO composite with 8 wt% GO, exhibited effective electrical conductivity of 0.015 S m^?1 and excellent specific shielding efficiency value of 693 dB cm² g^?1. In addition, the thermal stability of the porous PI/RGO composite films was also dramatically enhanced. Compared with that of porous PI film, the 5% weight loss temperature of the composite film mentioned above was improved from 525°C to 538°C. Moreover, tensile test showed that the composite film mentioned above possessed a tensile strength of 6.97 MPa and Young's modulus of 545 MPa, respectively. Copyright © 2016 John Wiley & Sons, Ltd.     

Nonenzymatic amperometric glucose sensor based on a composite prepared from CuO,reduced graphene oxide,and carbon nanotube

Microchimica Acta - The authors demonstrate a non-enzymatic sensor for glucose that is making used of an electrode prepared from an ink composed of CuO, reduced graphene oxide and carbon nanotube...     

Production of highly electro-conductive cellulosic paper via surface coating of carbon nanotube/graphene oxide nanocomposites using nanocrystalline cellulose as a binder

Electro-conductive cellulosic paper has attracted great attention as a promising alternative material in the emerging field of flexible and portable electronic devices. However, the environmentally friendly fabrication of electro-conductive cellulosic paper still remains challenging. Herein, green multi-walled carbon nanotube (MWCNT)/graphene oxide (GO) nanocomposites towards the sustainable development strategy were developed and subsequently used to impart electro-conductivity to cellulosic paper via surface coating process. GO exfoliated from graphite powder was used as a dispersant to improve the dispersion of MWCNTs in water media, and nanocrystalline cellulose (NCC) derived from cotton fibers was employed as a binder for the MWCNT/GO nanocomposites. Effect of NCC amount on the rheological behavior, particle size distribution, sedimentation stability and zeta potential of MWCNT/GO nanocomposites as well as the electro-conductivity and mechanical properties of coated paper was investigated. Results demonstrated that NCC enhanced the dispersion of MWCNT/GO nanocomposites in addition to serving as a binder. Surface coating application of MWCNT/GO nanocomposites was found to impart high electro-conductivity of up to 892 S m^?1 to the cellulosic paper while improving its mechanical properties.     

Synthesis of polyaniline/multiwall carbon nanotube composite via inverse emulsion polymerization

The composite of polyaniline (PANI) and multiwall carbon nanotube carboxylated through acid treatment (c‐MWCNT) was synthesized by chemical oxidative polymerization in an inverse emulsion system. The resultant composites were compared with products from aqueous emulsion polymerization to observe the improvements in electrical conductivity, structural properties, and thermal stability obtained by this synthetic method. Prior to the inverse emulsion polymerization, MWCNT was treated with a strong acid mixture to be functionalized with carboxylic acid groups. Carboxylic acid groups on surfaces induced selective dispersibility between polar and nonpolar solvents because of the increase of hydrophilicity. As the content of c‐MWCNT was increased, the electrical conductivity was increased by a charge transport function from the intrinsic electrical conductivity of MWCNT and the formation of a highly ordered dense structure of PANI molecules on the surface of c‐MWCNT. The images observed with electron spectroscopy showed the capping of c‐MWCNT with PANI. The growth of additional ordered structures of PANI/c‐MWCNT composite, which was observed through wide‐angle X‐ray diffraction patterns, supported the capping by PANI. It was observed that the doping of the composite had a significant relationship with the concentration of dodecylbenzenesulfonic acid (DBSA). The thermal stability of PANI composite was improved by the addition of c‐MWCNT; this was thought to be related with structure ordering by inverse emulsion polymerization. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2255–2266, 2008     

Design of a new hypoxanthine biosensor: xanthine oxidase modified carbon film and multi-walled carbon nanotube/carbon film electrodes

A new and simple-to-prepare hypoxanthine biosensor has been developed using xanthine oxidase (XOD) immobilised on carbon electrode surfaces. XOD was immobilised by glutaraldehyde cross-linking on carbon film (CF) electrodes and on carbon nanotube (CNT) modified CF (CNT/CF). A comparison of the performance of the two configurations was carried out by the current response using amperometry at fixed potential; the best characteristics being exhibited by XOD/CNT/CF modified electrodes. The effects of electrolyte pH and applied potential were evaluated, and a proposal is made for the enzyme mechanism of action involving competition between regeneration of flavin adenine dinucleotide and reduction of hydrogen peroxide. Under optimised conditions, the determination of hypoxanthine was carried out at ?0.2 V vs. a saturated calomel electrode (SCE) with a detection limit of 0.75 μM on electrodes with CNT and at ?0.3 V vs. SCE with a detection limit of 0.77 μM on electrodes without CNT. The applicability of the biosensor was verified by performing an interference study, reproducibility and stability were investigated, and hypoxanthine was successfully determined in sardine and shrimp samples.     

聚苯胺/顺丁橡胶复合导电膜的制备与性能(Ⅱ)

采用再掺杂方法制得了樟脑磺酸掺杂的聚苯胺(PAn-CSA),用溶液共混法制备PAn／BR导电复合膜．研究了聚苯胺与顺丁橡胶(BR)复合膜在间甲酚二次掺杂前后电导率的变化。实验表明:CSA对聚苯胺有较好的掺杂作用;二次掺杂使PAn复合膜电导率明显提高,其导电渗滤阈值略有降低,使卷曲的二次掺杂PAn链展开并通过分子链间的相互作用而自行组成导电通路．     

Formation of homogeneous nanocomposite films at ambient temperature via miniemulsion polymerization using graphene oxide as surfactant

A convenient and industrially scalable method for synthesis of homogeneous nanocomposite films comprising poly(styrene‐stat‐butyl acrylate) and nanodimensional graphene oxide (GO) or reduced GO (rGO) is presented. Importantly, the nanocomposite latex undergoes film formation at ambient temperature, thus alleviating any need for high temperature or high pressure methods such as compression molding. The method entails synthesis of an aqueous nanocomposite latex via miniemulsion copolymerization relying on nanodimensional GO sheets as sole surfactant, followed by ambient temperature film formation resulting in homogeneous film. For comparison, a similar latex obtained by physical mixing of a polymer latex with an aqueous GO dispersion results in severe phase separation, illustrating that the miniemulsion approach using GO as surfactant is key to obtaining homogeneous nanocomposite films. Finally, it is demonstrated that the GO sheets can be readily reduced to rGO in situ by heat treatment of the film. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2289–2297