Localization of hydrogen peroxide accumulation and diamine oxidase activity in pea root nodules under aluminum stress

Aluminum (Al) is one of the environmental stressors that induces formation of reactive oxygen species (ROS) in plants. Hydrogen peroxide (H₂O₂) and H₂O₂-generated apoplast diamine oxidase (DAO) activity were detected cytochemically via transmission electron microscopy (TEM), in pea (Pisum sativum L.) root nodules exposed to high (50 μM AlCl₃, for 2 and 24 h) Al stress.The nodules were shown to respond to Al stress by disturbances in infection thread (IT) growth, bacteria endocytosis, premature degeneration of bacteroidal tissue and generation of H₂O₂ in nodule apoplast. Large amounts of peroxide were found at the same sites as high DAO activity under Al stress, suggesting that DAO is a major source of Al-induced peroxide accumulation in the nodules. Peroxide distribution and DAO activity in the nodules of both control plants and Al-treated ones were typically found in the plant cell walls, intercellular spaces and infection threads. However, 2 h Al treatment increased DAO activity and peroxide accumulation in the nodule apoplast and bacteria within threads. A prolonged Al treatment (24 h) increased the H₂O₂ content and DAO activity in the nodule apoplast, especially in the thread walls, matrix and bacteria within infection threads. In addition to ITs, prematurely degenerated bacteroids, which occurred in response to Al, were associated with intense staining for H₂O₂ and DAO activity.These results suggest the involvement of DAO in the production of a large amount of H₂O₂ in the nodule apoplast under Al stress. The role of reactive oxygen species in pea-Rhizobium symbiosis under Al stress is discussed.     

SEM-EDX study of the crystal structure of the condensed combustion products of the aluminum nanopowder burned in air under the different pressures

The experimental results of combustion of aluminum nanopowder (ANP) in air and AlN crystals formation process were studied. The air pressure during the combustion process significantly affected the crystals growth mechanism. Crystals with the different morphology (whiskers, hexagonal crystals, rods) were found in the condensed combustion products.     

用金刚石车削技术制备EOS实验用铝薄膜和铜薄膜

 具有材料理论密度的金属薄膜对于材料高压状态方程(EOS)研究而言具有重要的意义。本文提出采用金刚石车削技术,利用超精密金刚石车床、金刚石圆弧刀具及真空吸附夹持技术,对纯铝和无氧铜进行端面车削,完成了EOS实验用铝薄膜和铜薄膜的车削加工,实现了薄膜密度接近材料理论密度。精加工工艺参数为：进给量0.001 mm/r,主轴转速3000 r/min,切削深度1 μm。采用Form Talysurf series 2型触针式轮廓仪进行测量,结果表明：铝薄膜、铜薄膜厚度可以达到小于10 μm水平,表面均方根粗糙度小于5 nm,原始最大轮廓峰-谷高度小于50 nm,厚度一致性好于99%。     

Characterization of acoustic streaming in water and aluminum melt during ultrasonic irradiation

It is well known that ultrasonic cavitation causes a steady flow termed acoustic streaming. In the present study, the velocity of acoustic streaming in water and molten aluminum is measured. The method is based on the measurement of oscillation frequency of Karman vortices around a cylinder immersed into liquid. For the case of acoustic streaming in molten metal, such measurements were performed for the first time. Four types of experiments were conducted in the present study: (1) Particle Image Velocimetry (PIV) measurement in a water bath to measure the acoustic streaming velocity visually, (2) frequency measurement of Karman vortices generated around a cylinder in water, and (3) in aluminum melt, and (4) cavitation intensity measurements in molten aluminum. Based on the measurement results (1) and (2), the Strouhal number for acoustic streaming was determined. Then, using the same Strouhal number and measuring oscillation frequency of Karman vortices in aluminum melt, the acoustic streaming velocity was measured. The velocity of acoustic streaming was found to be independent of amplitude of sonotrode tip oscillation both in water and aluminum melt. This can be explained by the effect of acoustic shielding and liquid density.     

Effect of welding wires on microstructure and mechanical properties of 2A12 aluminum alloy in CO2 laser-MIG hybrid welding

This paper represented the effect of welding wires on microstructure and mechanical properties of 2A12 aluminum alloy in CO₂ laser-metal inter gas (MIG) hybrid welding. Plates of 2A12 aluminum alloy were welded by ER4043 and ER2319 welding wires, respectively. Full penetration joints without any defects were produced. The X-ray diffraction was used to analyze the phase composition, while the scanning electron microscopy (SEM) was conducted to study the microstructure, segregation behaviors of major alloying elements and the eutectics formed at dendrite boundaries in the joints. The results showed that silicon and copper were concentrated at the dendrite boundaries and α-Al + Si + Al₂Cu + Mg₂Si eutectic was formed if the ER4043 welding wire was used. However, only copper was concentrated at the dendrite boundaries and α-Al + θ eutectic was formed by ER2319 welding wire. Finally, the tensile tests were performed and the fracture surfaces were analyzed. The results showed that the joint efficiency by ER2319 and ER4043 welding wires reached up to 78% and 69%, respectively. Coarse dimples and voids had been observed in the fractographs. The joints showed a transgranular type failure.     

Mechanisms of deformation localization and mechanical twinning under the conditions of phase instability of a crystal in stress fields

A new mechanism of the deformation and reorientation of a crystal has been studied experimentally and theoretically. This mechanism, which is effective in strain localization mechanical twinning bands of metal alloys and intermetallides, is a mechanism of dynamic phase (direct plus reverse martensitic) transformations in fields of high local stresses. The features of the reorientation and the defect substructure in these bands are discussed using electron microscopy data. With models of martensitic transformations based on the concept of cooperative thermal vibrations of extended coherent objects in crystals, the atomic mechanisms of direct plus reverse transformations are analyzed and the reorientation matrices (vectors) and distortion tensors are calculated for some (fcc bcc fcc, bcc hcp bcc) variants of these transformations. The carriers and nature of the above deformation mechanism and the principal physical effects underlying this mechanism are discussed.Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 8, pp. 28–48, August, 2004.     

Preignition characteristics of nano- and micrometer-scale aluminum particles in Al–CO2 oxidation systems

The objective of this study was to gain understanding of the preignition oxidation of Al powders in CO₂. The thermal behavior and reaction energy was studied using simultaneous thermogravimetric analysis and differential scanning calorimetry (TG–DSC). The particle morphology was examined at different stages of the process using field emission gun scanning electron microscopy (FEG-SEM) and transmission electron microscopy (TEM). The corresponding chemical changes were analyzed by X-ray diffraction spectrometry (XRD) and energy dispersion X-ray spectrometry (EDS). Dimensional properties of Al particles have a significant influence on the oxidation processes. Distinctly different properties were shown between nm-Al and μm-Al, where the reactions are found to occur at different temperature ranges. The powder behavior is controlled by the oxide layer that coats each particle and prevents exposure of the metal core to the reactive CO₂ gas. The properties of the oxide layer are related to the particle size. Carbon has been shown to play an important role in the reacting Al–CO₂ system. A new mechanism of nano-Al particle oxidation in CO₂ under gradually increasing temperature was proposed.     

冲击加载下铝中氦泡和孔洞的塑性变形特征研究

通过分子动力学模拟研究了在相同冲击加载强度下单晶铝中氦泡和孔洞的塑性变形特征,结果发现氦泡和孔洞的塌缩是由发射剪切型位错环引起的,而没有观测到棱锥型位错环发射. 氦泡和孔洞周围的位错优先成核位置基本一致,但是氦泡周围发射的位错环数目比孔洞多,位错环发射速度明显比孔洞快. 且氦泡和孔洞被冲击波先扫过部分比后扫过部分发射位错困难. 通过滑移面上的分解应力分析发现,氦泡和孔洞周围塑性特征的差别是由于氦泡内压引起最大分解应力分布改变造成的. 氦泡和孔洞被冲击波先后扫过部分塑性不对称是因为冲击波扫过时引起形状变化, 关键词： 分子动力学 冲击波 氦泡 孔洞     

Measurement of target fragments produced by 160 MeV proton beam in aluminum and polyethylene with CR-39 plastic nuclear track detectors

Production of target fragments from reactions of 160 MeV proton beams in aluminum and polyethylene was measured with CR-39 plastic nuclear track detectors (PNTD). Due to the detection limit of PNTD, primary protons cannot be detected; only low-energy short-range target fragments are registered. As a feasibility study, a so called “two step etching method” was employed to get the linear energy transfer (LET) spectra, absorbed dose, and dose equivalent. This method is discussed in this paper, together with the measured results.     

Characterization of the E1′ center in quartz: Role of aluminum hole centers and oxygen vacancies

The growth of E₁′ centers in a variety of natural and synthetic quartz crystals has been investigated by employing the electron spin resonance technique. It has been reported that the growth of E₁′ centers, formed by irradiation and subsequent annealing at 300 °C for 15 min, scale with the concentration of the aluminum hole center, [AlO₄]⁰, till a limit. Later, the E₁′ centers show saturation even when the [AlO₄]⁰-center continues to grow. For quartz with low efficiency of the formation of [AlO₄]⁰-center or irradiated with low accumulated doses, the intensity of E₁′ center was small where not all oxygen vacancies are converted to the E₁′ center. Thus, besides the availability of a number of oxygen vacancy sites, the number of holes released from the [AlO₄]⁰-center plays an important role in the formation of E₁′ centers in quartz.     

Variations in defect substructure and fracture surface of commercially pure aluminum under creep in weak magnetic field

Commercially pure polycrystalline aluminum of grade A85, as a test material, is investigated. Using scanning and transmission electron microscopy the aluminum fine structure and fracture surface are analyzed. Fractures are studied in the regime of creep with and without a simultaneous effect of 0.3-T magnetic field. It is found that the application of a magnetic field in a linear stage of creep leads to substructure imperfection increasing. Furthermore, the magnetic field effect on aluminum in the process of creep causes the average scalar density of dislocations to increase and induces the process of dislocation loop formation to strengthen. Fractographic investigation of the fracture surface shows that in the fibrous fracture zone the average size of plastic fracture pits decreases more than twice under creep in the condition of external magnetic field compared with in the conventional experimental condition. In a shear zone, the magnetic field causes the average size of fracture pits to decrease. Experimental data obtained in the research allow us to conclude that the magnetic field effect on aluminum in the process of creep leads to the fracture toughness value of the material decreasing, which will affect the state of defect substructure of the volume and surface layer of the material. The influence of the magnetic field is analyzed on the basis of the magneto-plasticity effect.     

Nucleation and growth of cavities in soft viscoelastic layers under tensile stress

The process of growth of an individual cavity in a viscoelastic adhesive layer has been investigated experimentally. The formation of cavities was caused by the application of a negative pressure on a very confined layer with a flat-ended probe. The cavities appeared in the bulk of the adhesive layer and were observed for a range of values of applied stress approximately ten times higher than the shear modulus of the adhesive layer. Depending on the loading rate, the shape of the growing cavity changed from a flat disc to a more spherical shape. Furthermore, the growth rate of the cavity radius was consistent with a constant strain rate at the edge of the cavity, which suggests a constant level of stress at the edge of the cavity. Received 5 June 2002 RID="a" ID="a"Current address: Ethicon, Johnson & Johnson, Route 22 West, P.O. Box 151, Somerville, NJ 08876-0151, USA. RID="b" ID="b"e-mail: costantino.creton@espci.fr     

Modeling of stress transfer behavior in fiber-matrix composite under axial and transverse loadings

Interface between fiber and matrix as a stress transfer medium determines composite performances in load-bearing structures. For instance, failures in composite are most likely initiated by an accumulation of interfacial cracks allowing little or no stress transfer from the matrix to the fiber and vice versa. This paper studies stress transfer behaviors at the interface subject to axial and transverse loadings using the finite element method. Single fiber surrounded by matrix was modeled by introducing a cohesive zone model (CZM) at the interface taking into account the bonding mechanism. By the proposed technique, plastic deformation in the matrix and exerted friction at the interface was verified to govern the role of stress transfer at the interface. Further, the influence of other fibers in matrix surrounding the model was also discussed.     

Growth of interfacial debonding in notched two-dimensional unidirectional composite under stress and displacement controls

A simplified calculation method for study of the growth of interfacial debonding between elastic fiber and elastic matrix ahead of the notch-tip in composites under displacement and stress controlled conditions was presented based on the shear lag approach in which the influences of residual stress and frictional shear stress at the debonded interface were incorporated. The calculation method was applied to a model two-dimensional composite. An outline is given of the difference and similarity in the growing behavior of the debonding between the displacement and stress controls, and of the influences of the residual stresses, frictional shear stress, the nature of the final cut component (fiber or matrix) and sample length on the debonding behavior.     

Molecular dynamics study of thermal stress and heat propagation in tungsten under thermal shock

Using molecular dynamics （MD） simulation, we study the thermal shock behavior of tungsten （W）, which has been used for the plasma facing material （PFM） of tokamaks. The thermo-elastic stress wave, corresponding to the collective displacement of atoms, is analyzed with the Lagrangian atomic stress method, of which the reliability is also analyzed. The stress wave velocity corresponds to the speed of sound in the material, which is not dependent on the thermal shock energy. The peak pressure of a normal stress wave increases with the increase of thermal shock energy. We analyze the temperature evolution of the thermal shock region according to the Fourier transformation. It can be seen that the “obvious” velocity of heat propagation is less than the velocity of the stress wave; further, that the thermo-elastic stress wave may contribute little to the transport of kinetic energy. The heat propagation can be described properly by the heat conduction equation. These results may be useful for understanding the process of the thermal shock of tungsten.     

Investigation of positively charged acceptor states in Si and Ge under uniaxial stress by phonon induced conduction

We use superconducting Al-tunnel junctions as tunable phonon generators in the meV-range to determine ground state splitting at zero stress of positively charged states associated with single acceptors in Si and double acceptors in Ge. From the stress and energy dependence of the conductivity induced by high frequency phonon irradiation of the corresponding two- and three-hole states we find that the splitting is below 0.1 meV for the ground states of Si:B⁺ and Ge:Be⁺, and 1 meV and 1.2 meV for Si:Ga⁺ and Si:Al⁺, respectively. These level separations are comparable to those found previously for the ground states of the corresponding acceptor bound excitons A⁰X. For the deeper acceptors Si:In⁺, Si:Tl⁺, and Ge:Zn⁺ the results are qualitatively different.     

Numerical study of stress and plastic strain evolution under compression and shear of a sample in a rotational anvil cell

The large-strain problem on the evolution of distribution of the components of stress tensor and plastic strain in a sample under compression and torsion in a rotational anvil cell was formulated and studied in detail using the FEM. Results are obtained for compression by different axial forces and torsion under two different constant axial forces. The effects of redistribution of the friction radial and torsional stresses and the load on a sample and gasket on the resultant fields are elucidated. Small pressure self-multiplication effect is revealed during torsion after compression below some critical force, and significant heterogeneity of all fields is found. Strong shear strain localization near the contact surface between sample and anvil is quantified. Results are compared with the simplified solution and available experiments. The results obtained are important for the determination of elastic and plastic properties of materials under high pressure and for the interpretation of kinetics of strain-induced phase transformations and chemical reactions.     

Core structure and Peierls stress of the 90° dislocation and the 60° dislocation in aluminum investigated by the fully discrete Peierls model

The core structure, Peierls stress and core energy, etc. are comprehensively investigated for the $90^\circ$ dislocation and the $60^\circ$ dislocation in metal aluminum using the fully discrete Peierls model, and in particular thermal effects are included for temperature range $0\leq T \leq 900$ K. For the $90^\circ$ dislocation, the core clearly dissociates into two partial dislocations with the separating distance $D\sim 12$ Å, and the Peierls stress is very small $\sigma_{\rm p}<1$ kPa. The nearly vanishing Peierls stress results from the large characteristic width and a small step length of the $90^\circ$ dislocation. The $60^\circ$ dislocation dissociates into $30^\circ$ and $90^\circ$ partial dislocations with the separating distance $D\sim 11$ Å. The Peierls stress of the $60^\circ$ dislocation grows up from $1$ MPa to $2$ MPa as the temperature increases from $0$ K to $900$ K. Temperature influence on the core structures is weak for both the $90^\circ$ dislocation and the $60^\circ$ dislocation. The core structures theoretically predicted at $T=0$ K are also confirmed by the first principle simulations.     

15N and 31P solid-state NMR study of transmembrane domain alignment of M2 protein of influenza A virus in hydrated cylindrical lipid bilayers confined to anodic aluminum oxide nanopores

This communication reports the first example of a high resolution solid-state 15N 2D PISEMA NMR spectrum of a transmembrane peptide aligned using hydrated cylindrical lipid bilayers formed inside nanoporous anodic aluminum oxide (AAO) substrates. The transmembrane domain SSDPLVVA(A-15N)SIIGILHLILWILDRL of M2 protein from influenza A virus was reconstituted in hydrated 1,2-dimyristoyl-sn-glycero-3-phosphatidylcholine bilayers that were macroscopically aligned by a conventional micro slide glass support or by the AAO nanoporous substrate. 15N and 31P NMR spectra demonstrate that both the phospholipids and the protein transmembrane domain are uniformly aligned in the nanopores. Importantly, nanoporous AAO substrates may offer several advantages for membrane protein alignment in solid-state NMR studies compared to conventional methods. Specifically, higher thermal conductivity of aluminum oxide is expected to suppress thermal gradients associated with inhomogeneous radio frequency heating. Another important advantage of the nanoporous AAO substrate is its excellent accessibility to the bilayer surface for exposure to solute molecules. Such high accessibility achieved through the substrate nanochannel network could facilitate a wide range of structure-function studies of membrane proteins by solid-state NMR.