Nano-wire networks of sulfur–polypyrrole composite cathode materials for rechargeable lithium batteries

Polypyrrole (PPy) nanowire was synthesized through a surfactant mediated approach. The sulfur–polypyrrole (S–PPy) composite materials were prepared by heating the mixture of element sulfur and polypyrrole nanowire. The materials were characterized by FTIR, SEM. PPy with special morphology serves as conductive additive, distribution agent and absorbing agents, which effectively enhanced the electrochemical performance of sulfur. The initial discharge capacity of the active materials was 1222 mA h g⁻¹ the remaining capacity is 570 mA h g⁻¹ after 20th cycles.     

Facile synthesis of multiwalled carbon nanotube–V2O5 nanocomposites as cathode materials for Li-ion batteries

Multiwalled carbon nanotube (MWCNT)–vanadium pentoxide (V₂O₅) nanocomposites have been fabricated using a facile and environmental friendly hydrothermal method without any pretreatment, surfactants, or chelate agents added. The as-annealed nanocomposites are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), and the results indicate that V₂O₅ nanoparticles grew on MWCNTs. As a cathode material for lithium batteries, it exhibits superior electrochemical performance compare to the pure V₂O₅ powders. A high specific discharge capacity of 253 mA h g^?1 can be obtained for the 15 % MWCNT–V₂O₅ nanocomposite electrodes, which retains 209 mA h g^?1 after 50 cycles. However, the pure V₂O₅ powder electrodes only possess a specific discharge capacity of 157 mA h g^?1 with a capacity retention of 127 mA h g^?1 after 50 cycles. Moreover, the MWCNT–V₂O₅ nanocomposite electrodes show an excellent rate capability with a specific discharge capacity of 180 mA h g^?1 at the current rate of 4 C. The enhanced electrochemical performance of the nanocomposites is attributed to the formation of conductive networks by MWCNTs, and large surface areas of V₂O₅ nanoparticles grew on MWCNTs which stabilizes these nanoparticles against agglomeration.     

Synthesis and electrochemical performance of TiO2–sulfur composite cathode materials for lithium–sulfur batteries

Titania–sulfur (TiO₂–S) composite cathode materials were synthesized for lithium–sulfur batteries. The composites were characterized and examined by X-ray diffraction, nitrogen adsorption/desorption measurements, scanning electron microscopy, and electrochemical methods, such as cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests. It is found that the mesoporous TiO₂ and sulfur particles are uniformly distributed in the composite after a melt-diffusion process. When evaluating the electrochemical properties of as-prepared TiO₂–S composite as cathode materials in lithium–sulfur batteries, it exhibits much improved cyclical stability and high rate performance. The results showed that an initial discharge specific capacity of 1,460 mAh/g at 0.2 C and capacity retention ratio of 46.6 % over 100 cycles of composite cathode, which are higher than that of pristine sulfur. The improvements of electrochemical performances were due to the good dispersion of sulfur in the pores of TiO₂ particles and the excellent adsorbing effect on polysulfides of TiO₂.     

Improved electrochemical properties of chromium substituted in LiCr1 ? x Ni x O2 cathode materials for rechargeable lithium-ion batteries

Pristine- and chromium-substituted LiNiO₂ nanoparticles were synthesized by sol-gel method using nitrate precursor at 800?°C for 12?h. Physical properties of the synthesized product were analyzed using Fourier transform infrared, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive analysis X-ray. XRD studies revealed a well-defined layer structure and a linear variation of lattice parameters with the addition of chromium and no impurities. Surface morphology and particle size of synthesized materials were changed with chromium addition using SEM and TEM analyses. Assembled lithium-ion cells were evaluated for charge/discharge studies at different rates, cyclic voltammetry, and electrochemical impedance spectra. The initial discharge capacity of LiNiO₂ cathode material was found to be 168?mA hg^?1; however, discharge capacity increased in chromium substitution. Electrochemical impedance spectroscopy revealed that LiCr_0.10Ni_0.90O₂ could enhance charge transfer resistance upon cycling. The substitution of Ni with chromium, LiCr_0.10Ni_0.90O₂, had better cycle life, low irreversible capacity, and excellent electrochemical performance.     

Boron-doped Ketjenblack based high performances cathode for rechargeable Li–O_2 batteries

Boron-doped Ketjenblack is attempted as cathode catalyst for non-aqueous rechargeable Li–O_2 batteries. The boron-doped Ketjenblack delivers an extremely high discharge capacity of 7193 m Ah/g at a current density of 0.1 m A/cm2, and the capacity is about 2.3 times as that of the pristine KB. When the batteries are cycled with different restricted capacity, the boron-doped Ketjenblack based cathodes exhibits higher discharge platform and longer cycle life than Ketjenblack based cathodes. Additionally, the boron-doped Ketjenblack also shows a superior electrocatalytic activity for oxygen reduction in 0.1 mol/L KOH aqueous solution. The improvement in catalytic activity results from the defects and activation sites introduced by boron doping.     

Capacity of layered cathode materials for lithium-ion batteries — a theoretical study and experimental evaluation

The theoretical capacity and the vacancy concentration of metal-ion-doped layered compounds such as LiCoO₂, LiNiO₂, and LiMnO₂, acting as cathodes in high-voltage lithium-ion batteries are calculated. The capacity shows strong dependence on valency of the doped metal ion and vacancy concentration. Experimental verification carried out to check the validity of the proposed equation for aluminium substitution into the potential layered materials shows good agreement between the experimental and theoretical capacity values. The vacancy concentration values of doped layered compounds have been found to be high when compared with that of the doped spinel compounds.     

High aspect ratio γ-MnOOH nanowires for high performance rechargeable nonaqueous lithium-oxygen batteries

High aspect ratio γ-MnOOH nanowires (MNWs) are synthesized by a simple one-step hydrothermal method and used as catalysts in rechargeable nonaqueous lithium-oxygen batteries. When the nanowires are employed, great improvements in discharge capacity, cycle stability, and rate retention are obtained, which are attributed to the high catalyst efficiency and the cathode porosity.     

Low-cost and facile one-pot synthesis of pure single-crystalline ε-Cu(0.95)V2O5 nanoribbons: high capacity cathode material for rechargeable Li-ion batteries

Pure single-crystalline ε-Cu(0.95)V(2)O(5) nanoribbons have been successfully synthesized via a facile one-pot solvothermal route using low-cost raw materials. The obtained materials can react electrochemically with 2.64 Li in a reversible fashion and thus greatly expands the range of cathode choices.     

Synthesis of Li3Ni x V2−x (PO4)3/C cathode materials and their electrochemical performance for lithium ion batteries

Li₃Ni _x V_2?x (PO₄)₃/C (x?=?0, 0.02, 0.04 and 0.06) samples have been synthesized via an improved sol–gel method. X-ray diffraction patterns indicate that the structure of the prepared samples retains monoclinic, and the single phase has not been changed with Ni doping. From the analysis of electrochemical performance, the Li₃Ni_0.04?V_1.96(PO₄)₃/C sample exhibits the best electrochemical property. It delivers a discharge capacity of 112.1 mAh?g^?1 with capacity retention of 95.2 % over 300 cycles at 10 C rate in the range of 3.0–4.8 V; cyclic voltammetry and electrochemical impedance spectra testing further prove that the electrochemical reversibility and lithium ion diffusion behavior of Li₃V₂(PO₄)₃ have also been effectively improved through Ni doping.     

Synthesis and electrochemical performance of sulfur–carbon composite cathode for lithium–sulfur batteries

In this paper, porous carbon was synthesized by an activation method, with phenolic resin as carbon source and nanometer calcium carbonate as activating agent. Sulfur–porous carbon composite material was prepared by thermally treating a mixture of sublimed sulfur and porous carbon. Morphology and electrochemical performance of the carbon and sulfur–carbon composite cathode were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), cyclic voltammetry (CV), electrochemical impedance spectra (EIS), and galvanostatic charge–discharge test. The composite containing 39 wt.% sulfur obtained an initial discharge capacity of about 1,130 mA?h g^?1 under the current density of 80 mA?g^?1 and presented a long electrochemical stability up to 100 cycles.     

A novel synthetic route for LiFePO_4/C cathode materials by addition of starch for lithium-ion batteries

LiFePO4/Carbon composite cathode material was prepared using starch as carbon source by spray-pelleting and subsequent pyrolysis in N2. The samples were characterized by XRD, SEM, Raman, and their electrochemical performance was investigated in terms of cycling behavior. There has a special micro-morphology via the process, which is favorable to electrochemical properties. The discharge capacity of the LiFePO4.C composite was 170 mAh g-1, equal to the theoretical specific capacity at 0.1 C rate. At 4 C current density, the specific capacity was about 80 mAh g-1, which can satisfy for transportation applications if having a more flat discharge flat.     

Synthesis and electrochemical performance of CeO2@CNTs/S composite cathode for Li–S batteries

The shuttle effect of lithium-sulfur (Li–S) battery is one of the crucial factors restraining its commercial application, because LiPSs (lithium polysulfides) usually leads to poor cycle life and low coulomb efficiency. Some studies have shown that metal oxides can adsorb soluble polysulfides. Herein, CeO₂ (cerium-oxide)-doped carbon nanotubes (CeO₂@CNTs) were prepared by the hydrothermal method. The polar metal oxide CeO₂ enhanced the chemisorption of the cathode to LiPSs and promoted the redox reaction of the cathode through catalysis properties. Meanwhile, the carbon nanotubes (CNTs) enhanced cathode conductivity and achieved more sulfur loading. The strategy could alleviate polysulfide shuttling and accelerate redox kinetics, improving Li–S batteries' electrochemical performances. As a result, the CeO₂@CNTs/S composite cathode showed the excellent capacity of 1437.6 mAh g⁻¹ in the current density of 167.5 mA g⁻¹ at 0.1 C, as well as a long-term cyclability with an inferior capacity decay of 0.17% per cycle and a superhigh coulombic efficiency of 100.434% within 300 cycles. The superior electrochemical performance was attributed to the polar adsorption of CeO₂ on polysulfides and the excellent conductivity of CNTs.

     

Synthesis,characterization and electrochemical properties of α-MoO<Subscript>3</Subscript> nanobelts for Li-ion batteries

Orthorhombic molybdenum trioxide (α-MoO₃) nanobelts have been successfully synthesized by hydrothermal method at 180°C for 20 h. The prepared α-MoO₃ samples were investigated by X-ray diffraction, Fourier transform IR spectroscopy, Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy methods. It was found that α-MoO₃ nanobelts grow along the c-axis, with ±(100) top or bottom surfaces and ±(010) side surfaces. The prepared α-MoO₃ nanobelts were used as cathode materials for Li-ion batteries. They exhibit specific capacity of 1340 and 1250 mA h g^–1 at a current density of 100 and 400 mA/g, respectively.     

Electrochemical performance of γMnO2 prepared from the active mass of used batteries

Russian Journal of Applied Chemistry - We prepared MnO2 by electrolysis of manganese sulfate solution recovered from used batteries and commercial manganese sulfate solution. The comparative study...     

Carbon/Ba–Fe–Si alloy composite as high capacity anode materials for Li-ion batteries

A novel Ba–Fe–Si/C composite was prepared by mechanical ball milling and lithium insertion reactions on the composite electrode were investigated by cyclic voltammetry, charge–discharge measurements, XRD and XPS spectroscopy. It is demonstrated that the composite electrode not only possesses sufficiently high reversible capacity of ca. 420 mA h/g, but also exhibits strong capacity retention with indiscernible capacity decay during charge–discharge cycling. The improved cycling ability of the composite is suggested from a cooperative action by inactive FeSi₂ and BaSi₂ matrix and outer graphite shell, which both buffer the volumetric changes of the active Si phase and provide a good connection for electronic and ionic conduction during lithium insertion and extraction processes.     

Carbon fiber-incorporated sulfur/carbon ternary cathode for lithium–sulfur batteries with enhanced performance

Journal of Solid State Electrochemistry - Smart construction of advanced sulfur cathodes is indispensable for the development of high performance lithium–sulfur (Li–S) batteries. Hence,...     

Potassium pre-inserted K1.04Mn8O16 as cathode materials for aqueous Li-ion and Na-ion hybrid capacitors

For the applications of aqueous Li-ion hybrid capacitors and Na-ion hybrid capacitors,potassium ions are pre-inserted into MnO2 tunnel structure,the as-prepared K1.04Mn8 O16 materials consist of nanoparticles and nanorods were prepared by facile high-temperature solid-state reaction.The as-prepared materials were well studied and they show outstanding electrochemical behavior.We assembled hybrid supercapacitors with commercial activated carbon(YEC-8 A)as anode and K1.04Mn8 O16 as cathode.It shows high energy and power densities.Li-ion capacitors reach a high energy density of 127.61 Wh kg-1 at the power density of 99.86 W kg-1 and Na-ion capacitor obtains 170.96 Wh kg-1 at 133.79 W kg-1.In addition,the hybrid supercapacitors demonstrate excellent cycling performance which maintain 97%capacitance retention for Li-ion capacitor and 85%for Na-ion capacitor after 10,000 cycles.     

Preparation of NiO/multiwalled carbon nanotube nanocomposite for use as the oxygen cathode catalyst in rechargeable Li–O2 batteries

NiO/multiwalled carbon nanotube (NiO/MWCNT) nanocomposites have been prepared and used for a Li–O₂ battery cathode catalyst. Electrochemical measurements demonstrate that the batteries with NiO/MWCNT catalyst have a discharge capacity of 2,500 mAh g^?1, a charge capacity of 2,100 mAh g^?1, and a rechargeable ability performing better than Ketjenblack (KB) and MWCNTs. KB has the largest discharge capacity (2,700 mAh g^?1) due to the highest surface area and pore volume but the worst charging behavior due to poor mass transport in the small-width pore (2.48 nm). MWCNTs have a much better charging performance owing to a larger pore width (8.93 nm) than carbon black. NiO/MWCNTs have the largest charge capacity because of the facilitated mass transport in the comparatively large pores (7.68 nm) and the increased catalytic ability produced by the NiO nanoparticles. These improvements are also responsible for the best cycle and rate performances of the nanocomposites among the three catalysts.