Small field output factors: Comparison of measurements with various detectors and effects of detector orientation with primary jaw setting

Accurate dosimetry in small photon fields used in modern radiotherapy is a challenging task due to electronic disequilibrium, steep dose gradients, source occlusion and size of the sensitive volume of the detector. These challenging effects and the lack of metrological dosimetric reference instigated an investigation on the acquisition of output factor with various detectors in parallel and perpendicular orientations. Small field output factor measurements of tertiary collimators such as BrainLab circular cones, BrainLab mMLC and Millennium MLC were carried out in this study. The data acquired show the differences between output factor results with different detectors for all collimating systems. Good agreement in output values was observed in field sizes greater than ∼2 × 2 cm² for all detectors and all tertiary collimators. For smaller fields when compared to electron field diode (EFD), 0.125 cm³ ion chamber underestimates the output by up to −11.1% and −20.4% and pinpoint ion chamber underestimates the output by up to −1.5% and −6.1% in their parallel and perpendicular orientation, respectively. In contrast, PTW SRS diode and photon field diode (PFD) overestimate the output factor by up to 2.5% and 6.9% respectively in its parallel orientation. The investigated data for the effect of jaw position (0.25 × 0.25 cm², 0.5 × 0.5 cm² and 1 × 1 cm²) away from the field edge generated by different tertiary collimating systems inferred that the opening of X–Y jaw highly influences the small field output factors. The orientation of the detectors and the position of the jaws could influence the output factors considerably in small fields.     

Validation of Monte Carlo simulation of 6 MV photon beam produced by Varian Clinac 2100 linear accelerator using BEAMnrc code and DOSXYZnrc code

The Monte Carlo model for the photon-beam output from the Varian Clinac 2100 linear accelerator was validated to compare the calculated to measured PDD and beam dose profiles The Monte Carlo calculation method is considered to be the most accurate method for dose calculation in radiotherapy. The objective of this study is to build a Monte Carlo geometry of Varian Clinac 2100 linear accelerator as realistically as possible. The Monte Carlo codes used in this work were the BEAMnrc code to simulate the photons beam and the DOSXYZnrc code to examinate the absorbed dose in the water phantom. We have calculated percentage depth dose (PDD) and beam profiles of the 6 MV photon beam for the 6 × 6 cm², 10 × 10 cm² and 15 × 15 cm² field sizes. We have used the gamma index technique for the quantitative evaluation to compare the measured and calculated distributions. Good agreement was found between calculated PDD and beam profile compared to measured data. The comparison was evaluated using the gamma index method and the criterions were 3% for dose difference and 3 mm for distance to agreement. The gamma index acceptance rate was more than 97% of both distribution comparisons PDDs and dose profiles and our results were more developed and accurate. The Varian Clinac 2100 linear accelerator was accurately modeled using Monte Carlo codes: BEAMnrc and DOSXYZnrc codes package.     

The influence of field size and off-axis distance on photoneutron spectra of the 18 MV Siemens Oncor linear accelerator beam

At present, high energy electron linear accelerators (LINACs) producing photons with energies higher than 10 MeV have a wide use in radiotherapy (RT). However, in these beams fast neutrons could be generated, which results in undesired contamination of the therapeutic beams. These neutrons affect the shielding requirements in RT rooms and also increase the out-of-field radiation dose to patients. The neutron flux becomes even more important when high numbers of monitor units are used, as in the intensity modulated radiotherapy. Herein, to evaluate the exposure of patients and medical personnel, it is important to determine the full radiation field correctly. A model of the dual photon beam medical LINAC, Siemens ONCOR, used at the University Hospital Centre of Osijek was built using the MCNP611 code. We tuned the model according to measured photon percentage depth dose curves and profiles. Only 18 MV photon beams were modeled. The dependence of neutron dose equivalent and energy spectrum on field size and off-axis distance in the patient plane was analyzed. The neutron source strength (Q) defined as a number of neutrons coming from the head of the treatment unit per x-ray dose (Gy) delivered at the isocenter was calculated and found to be 1.12 × 10¹² neutrons per photon Gy at isocenter. The simulation showed that the neutron flux increases with increasing field size but field size has almost no effect on the shape of neutron dose profiles. The calculated neutron dose equivalent of different field sizes was between 1 and 3 mSv per photon Gy at isocenter. The mean energy changed from 0.21 MeV to 0.63 MeV with collimator opening from 0 × 0 cm² to 40 × 40 cm². At the 50 cm off-axis the change was less pronounced. According to the results, it is reasonable to conclude that the neutron dose equivalent to the patient is proportional to the photon beam-on time as suggested before. Since the beam-on time is much higher when advanced radiotherapy techniques are used to fulfill high conformity demands, this makes the neutron flux determination even more important. We also showed that the neutron energy in the patient plane significantly changes with field size. This can introduce significant uncertainty in dosimetry of neutrons due to strong dependence of the neutron detector response on the neutron energy in the interval 0.1–5 MeV.     

Photon beam softening coefficients evaluation for a 6 MeV photon beam for an aluminum slab: Monte Carlo study using BEAMnrc Code,DOSXYZnrc Code,and BEAMDP code

Determination and understanding the photon beam attenuation by the photon beam modifier and the radiation beam softening for clinical use is more important part of material study for the beam modifier enhancements and the linac improvements. A Monte Carlo model was used to simulate 6 MeV photon beams from a Varian Clinac 2100 accelerator with the flattening filter and the later was replaced by the aluminum slab with variable thickness. The Monte Carlo geometry was validated by a gamma index acceptance rate of 99% in PDD and 98% in dose profiles, the gamma criteria was 3% for dose difference and 3 mm for distance to agreement. The purpose was to investigate aluminum material attenuation and beam softening coefficients as a function of the inserted aluminum slab thickness and of off-axis distance. The attenuation and beam softening coefficients were not identical for the same off-axis distance and they varied as a function of aluminum slab thickness. The results of our study were shown that the beam softening coefficients were varied with thickness beam modifier material used for beam softening and the off-axis distance inside the irradiation field. Thereafter, the softening coefficient a ₁ have a maximum of 2.5 × 10^–1 cm^–1 for the aluminum slab thickness of 1 mm, 1.4 × 10^–1 cm^–1 for the aluminum slab thickness of 1.5 mm and 4.47 × 10^–2 cm^–1 for the aluminum slab thickness of 2 mm. The maximum of the second softening coefficient a ₂ was 1.02 × 10^–2 cm^–2 for the aluminum slab thickness of 1 mm, was 1.92 × 10^–2 cm^–2 for the aluminum slab thickness of 1.5 mm and was 1.93 × 10^–2 cm^–2 for the aluminum slab thickness of 2 mm. Our study can be a basic investigation of photon beam softening material that will be used in the future linac configuration and also in the photon beam modifiers.     

Monte Carlo investigation of the effect of small cutouts on beam profile parameters of 12 and 14 MeV electron beams

Cutouts, which are used as field-shaping shield, affect several electron beam parameters. These effects are more observable for small field sizes and high energy electron beams. Owing to the fact that small fields prevent the lateral scatter equilibrium, at higher energies larger field radius is required for the establishment of lateral equilibrium.The profile curves are derived from circular, triangular, and square cutout shapes and size placed in a 10 × 10 cm² electron applicator. These profile curves are obtained using parallel plane type ion chamber at the R₁₀₀, R₉₀, R₈₀ and R₅₀ depths. Correspondingly, the source surface distance is 100 cm.In this study MCNP Monte Carlo (MC) simulation was used to compare Percentage Depth Dose (PDD) and Profile of electron beams.Monte Carlo and measured results showed a good compliance for PDD and beam profile. The measurements and calculations showed that as the field width decreases, the Flatness and Penumbra Ratio also decreases. In other words, flatter plateau was available for larger fields. Also the Coverage Ratio for each of the profiles is presented. The flatness and symmetry values for triangle shapes were greater than the two other shapes.Knowledge of these changes are significant in radiation therapy. Accordingly, a comparison between the Monte Carlo data and the measured results can be beneficial for treatment simulation and development of treatment planning systems.     

X射线探测器的脉冲标定技术

利用强流电子束技术产生通量密度为10¹⁸—10¹⁹X-ray photon/sr·s的脉冲CuKX射线源,标定PIN型硅二极管半导体探测器对X光子的脉冲灵敏度。用绝对X射线监测器——P10气体脉冲电离室作为脉冲X射线通量密度的标准。脉冲电荷自动测量仪由微处理机进行程序控制,并予以实时校准。该电离室测量通量密度的精度为±5％,适用的能通量率范围可达4×10^-9—2×10²W/cm²,适用的光子能量范围为1.5—10keV,标定探测器的精度为±7.0％,并发现PIN型硅二极管的脉冲灵敏度比稳态X射线束标定的灵敏度高30％左右。 关键词：     

Evaluation of a liquid ionization chamber for relative dosimetry in small and large fields of radiotherapy photon beams

Commissioning and quality assurance of radiotherapy linear accelerators require measurement of the absorbed dose to water, and a wide range of detectors are available for absolute and relative dosimetry in megavoltage beams.In this paper, the PTW microLion isooctane-filled ionization chamber has been tested to perform relative measurements in a 6 MV photon beam from a linear accelerator. Output factors, percent depth dose and dose profiles have been obtained for small and large fields. These quantities have been compared with those from usual detectors in the routine practice. In order to carry out a more realistic comparison, an uncertainty analysis has been developed, taking type A and B uncertainties into account.The results present microLion as a good option when high spatial resolution is needed, thanks to its reduced sensitive volume. The liquid filling also provides a high signal compared to other detectors, like that based on air filling. Furthermore, the relative response of microLion when field size is varied suggests that this detector has energy dependence, since it is appreciated an over-response for small fields and an under-response for the large ones. This effect is more obvious for field sizes wider than 20 × 20 cm², where the differences in percent depth dose at great depths exceed the uncertainties estimated in this study.     

Characterization of GaN dosimetry for 6 MV photon beam in clinical conditions

We characterized a recently proposed implantable GaN-based dosimeter in clinical conditions, for its application in external radiotherapy according to ESTRO (European Society for Radiotherapy & Oncology) practical guidelines. Our studies were carried out using a 6 MV photon beam with the dosimeter under test in a water tank or a PMMA phantom. They were focused on evaluating short term and long term reproducibility of measurements, and assessing the effects of parameters such as field size, source-skin distance, use of wedge filter, beam incidence, dose rate, accumulated dose, GaN-induced dose perturbation, air cavities and temperature. The estimated repeatability and reproducibility are better than 0.5% and 2% at 1σ respectively. There are no significant effects of the parameters under our studies, apart from field size and temperature. The field-size dependence is due to over-compensation of the GaN response method of the dosimeter, the resulting errors remain lower than 5% for field sizes up to 10 × 10 cm². The temperature dependence mainly results from the GaN luminescence properties, and causes the GaN response to decrease steadily when increasing temperature, with a sensitivity of −1.4%/°C. The observed quasi-linear temperature dependence may facilitate the correction to improve the accuracy of measurements.     

Design and development of an optical beam splitter assembly and high precision colinearity measurements of laser beams

Laser beams with extremely high colinearity are often required where precision position monitoring is important. In order to achieve the said objective, a special type of Laser Beam Splitter Assembly (BSA) has been designed and fabricated in a very small volume due to space constraints. The main features and details of such a system are described here. This type of beam splitter assembly coupled with a diode laser through fibers can be remotely used for alignment or position monitoring of different medium to large size structures with a reconstruction accuracy of 10 μm. In this way, BSA generates two counter propagating laser beams from a single diode laser coupled to an optical fiber. In the present work, the colinearity between two beams within 1 mrad with the variation of 50 μrad has been achieved. The laser's power in the two arms may be controlled precisely, which is an important feature of this BSA. The BSA has been tested to work over a temperature range between ?20 °C to +40 °C. It has also been exposed to 1.0 MeV neutrons at a flux of ～5.0×10¹⁰ n/cm²/s and found compatible.     

A miniaturized prototype of resonant banana-shaped photoacoustic cell for gas sensing

A resonant photoacoustic cell intended for laser-spectroscopy gas sensing is represented. This cell is a miniature imitation of a macro-scale banana-shaped cell developed previously. The parameters, which specify the cavity shape, are chosen so as not only to provide optimal cell operation at a selected acoustic resonance but also to reduce substantially the cell sizes. A miniaturized prototype cell (the volume of acoustic cavity of ∼5 mm³) adapted to the narrow diffraction-limited beam of near-infrared laser is produced and examined experimentally. The noise-associated measurement error and laser-initiated signals are studied as functions of modulation frequency. The background signal and the useful response to light absorption by the gas are analyzed in measurements of absorption for ammonia in nitrogen flow with the help of a pigtailed DFB laser diode oscillated near a wavelength of 1.53 μm. The performance of prototype operation at the second longitudinal acoustic resonance (the resonance frequency of ∼32.9 kHz, Q-factor of ∼16.3) is estimated. The noise-limited minimal detectable absorption normalized to laser-beam power and detection bandwidth is ∼8.07 × 10⁻⁸ cm⁻¹ W Hz^−1/2. The amplitude of the background signal is equivalent to an absorption coefficient of ∼2.51 × 10⁻⁵ cm⁻¹. Advantages and drawbacks of the cell prototype are discussed. Despite low absorption-sensing performance, the produced miniaturized cell prototype shows a good capability of gas-leak detection.     

Study on energy dependence of PAGAT polymer gel dosimeter evaluated using X-Ray CT

The normoxic polymer gel dosimeter evaluated with X-Ray computed tomography has emerged as a promising tool for measuring the dose delivered during radiotherapy in three dimensions. This study presents the dependence of PAGAT normoxic polymer gel sensitivity to different photon and electron energies. PAGAT polymer gel was prepared under normal atmospheric condition and irradiated with different photon energies of 1.25 MeV from Co-60 and 6 MV and 15 MV from linear accelerator and electron energies of 6, 9, 12, 15, 18 and 21 MeV from linear accelerator. Evaluation of dosimeter was performed with an X-Ray CT scanner. Images were acquired with optimum scanning protocols to reduce the signal-to-noise ratio. The averaged image was subtracted from the unirradiated polymer gel image for background. Central axis depth dose (PDD) curves obtained for each energy and polymer gel dosimeter measurements were in good agreement with diode and film measurements. Hounsfield (HU) – dose response curve for each photon and electron energy were derived from the PDD curve obtained from the gel dosimeter measurements. From the study it was clear that the HU-dose response curve was linear in the region 1–10 Gy. The dosimeter sensitivity was defined as a slope of these linear HU-dose response curves and found that the sensitivity of polymer gel decreases with increase in both photon and electron energies. This trend in dependence of PAGAT gel dosimeter sensitivity to different photon and electron energies was not dosimetrically significant. However, to evaluate the test phantom exposed with one energy using the calibration curve derived at another energy can produce clinically significant error.     

I. Electron-impact ionization and dissociation of C<Subscript>2</Subscript>H<Stack><Subscript>2</Subscript><Superscript>+</Superscript></Stack> and C<Subscript>2</Subscript>D<Stack><Subscript>2</Subscript><Superscript>+</Superscript></Stack>

Absolute cross-sections for electron-impact ionization and dissociation of C₂H₂⁺ and C₂D₂⁺ have been measured for electron energies ranging from the corresponding thresholds up to 2.5 keV. The animated crossed beams experiment has been used. Light as well as heavy fragment ions that are produced from the ionization and the dissociation of the target have been detected for the first time. The maximum of the cross-section for single ionization is found to be (5.56 ± 0.03)× 10^-17 cm² around 140 eV. Cross-sections for dissociation of C₂ H₂⁺ (C₂D₂⁺) to ionic products are seen to decrease for two orders of magnitude, from C₂D⁺ (12.6 ± 0.3) × 10^-17 cm² over CH⁺(9.55 ± 0.06) × 10^-17 cm², C⁺ (6.66 ± 0.05) × 10^-17 cm², C₂⁺ (5.36 ± 0.27) × 10^-17 cm², H⁺ (4.73 ± 0.29) × 10^-17 cm² and CH₂⁺ (4.56 ± 0.27) × 10^-18 cm² to H₂⁺ (5.68 ± 0.49) × 10^-19 cm². Absolute cross-sections and threshold energies have been compared with the scarce data available in the literature.     

Two photon absorption characteristics of bulk GaTe crystal

We have investigated the structural and optical properties of bulk GaTe crystal grown by vertical Bridgman method. Two photon absorption (TPA) properties of GaTe crystal have been investigated by the open aperture Z-scan technique under 1064 nm wavelength with 4 ns or 65 ps pulse durations. The TPA coefficients are greater in ns regime than that of ps regime. Upon increasing intensity of incident light from 5.02×10⁷ W/cm² to 1.07×10⁸ W/cm², the TPA coefficients increased from 3.47×10^?6 cm/W to 8.53×10^?6 cm/W for nanosecond excitation. Similarly, when intensity of incident light was increased from 6.81×10⁸ W/cm² to 9.94×10⁸ W/cm² the TPA coefficients increased from 3.53×10^?7 cm/W to 6.83×10^?7 cm/W for picosecond excitation. Measured TPA coefficient of GaTe crystal is larger than that of GaSe and GaS layered crystals.     

Measurements of neutron radiation and induced radioactivity for the new medical linear accelerator,the Varian TrueBeam

Contemporary linear accelerators applied in radiotherapy generate X-ray and electron beams with energies up to 20 MeV. Such high-energy therapeutic beams induce undesirable photonuclear (γ,n) and electronuclear (e,e'n) reactions in which neutrons and radioisotopes are produced. The originated neutron can also induce reactions such as simple capture, (n,γ), reactions that produce radioisotopes. In this work measurements of the non-therapeutic neutrons and the induced gamma radiation were carried out in the vicinity of a new medical accelerator, namely the Varian TrueBeam. The TrueBeam is a new generation Varian medical linac making it possible to generate the X-ray beams with a dose rate higher than in the case of the previous models by Varian. This work was performed for the X-ray beams with nominal potentials of 10 MV (flattening filter free), 15 MV and 20 MV, and for a 22 MeV electron beam. The neutron measurements were performed by means of a helium chamber and the induced activity method. The identification of radioisotopes produced during emission of the therapeutic beams was based on measurements of the energy spectra of gammas emitted in decays of the produced nuclei. The gamma energy spectra were measured with the use of the high-purity germanium detector. The correlation between the neutron field and the mode and nominal potential was observed. The strongest neutron fluence of 3.1 × 10⁶ cm⁻² Gy⁻¹ and 2.0 × 10⁶ cm⁻² Gy⁻¹ for the thermal and resonance energies, respectively, was measured during emission of the 20 MV X-ray beam. The thermal and resonance neutron fluence measured for the 15 MV X-rays was somewhat less, at 1.1 × 10⁶ cm⁻² Gy⁻¹ for thermal neutrons and 6.7 × 10⁵ cm⁻² Gy⁻¹ for resonance neutrons. The thermal and resonance neutron fluences were smallest for the 10 MV FFF beam and the 22 MeV electron beam and were around two orders of magnitude smaller than those of the 20 MV X-ray beam. This work has shown that the neutron reactions are dominant because of relatively high cross sections for many elements used in the accelerator construction. The detailed analysis of the measured spectra made it possible to identify 11 radioisotopes induced during TrueBeam delivery. In this work the following radioisotopes were identified: ⁵⁶Mn, ¹²²Sb, ¹²⁴Sb, ¹³¹Ba, ⁸²Br, ⁵⁷Ni, ⁵⁷Co, ⁵¹Cr, ¹⁸⁷W, ²⁴Na and ³⁸Cl.     

Measurement of the third‐order nonlinear optical susceptibility χ(3) for the 1002‐cm–1 mode of benzenethiol using coherent anti‐Stokes Raman scattering with continuous‐wave diode lasers

The components of the third‐order nonlinear optical susceptibility χ⁽³⁾ for the 1002‐cm^–1 mode of neat benzenethiol have been measured using coherent anti‐Stokes Raman scattering with continuous‐wave diode pump and Stokes lasers at 785.0 and 852.0 nm, respectively. Values of 2.8 ± 0.3 × 10^–12, 2.0 ± 0.2 × 10^–12, and 0.8 ± 0.1 × 10^–12 cm·g^–1·s² were measured for the xxxx, xxyy, and xyyx components of |3χ⁽³⁾|, respectively. We have calculated these quantities using a microscopic model, reproducing the same qualitative trend. The Raman cross‐section σ_RS for the 1002‐cm^–1 mode of neat benzenethiol has been determined to be 3.1 ± 0.6 × 10^–29 cm² per molecule. The polarization of the anti‐Stokes Raman scattering was found to be parallel to that of the pump laser, which implies negligible depolarization. The Raman linewidth (full‐width at half‐maximum) Γ was determined to be 2.4 ± 0.3 cm^–1 using normal Stokes Raman scattering. The measured values of σ_RS and Γ yield a value of 2.1 ± 0.4 × 10^–12 cm·g^–1·s² for the resonant component of 3χ⁽³⁾. A value of 1.9 ± 0.9 × 10^–12 cm·g^–1·s² has been deduced for the nonresonant component of 3χ⁽³⁾. Copyright © 2011 John Wiley & Sons, Ltd.     

Epitaxial ZnO thin films grown by pulsed electron beam deposition

In this work, the pulsed electron beam deposition method (PED) is evaluated by studying the properties of ZnO thin films grown on c-cut sapphire substrates. The film composition, structure and surface morphology were investigated by means of Rutherford backscattering spectrometry, X-ray diffraction and atomic force microscopy. Optical absorption, resistivity and Hall effect measurements were performed in order to obtain the optical and electronic properties of the ZnO films. By a fine tuning of the deposition conditions, smooth, dense, stoichiometric and textured hexagonal ZnO films were epitaxially grown on (0001) sapphire at 700 °C with a 30° rotation of the ZnO basal plane with respect to the sapphire substrate. The average transmittance of the films reaches 90% in the visible range with an optical band gap of 3.28 eV. Electrical characterization reveals a high density of charge carrier of 3.4 × 10¹⁹ cm^?3 along with a mobility of 11.53 cm²/Vs. The electrical and optical properties are discussed and compared to ZnO thin films prepared by the similar and most well-known pulsed laser deposition method.     

Bias-selectable mid-/long-wave dual band infrared focal plane array based on Type-II InAs/GaSb superlattice

In this paper, a mid-/long-wave dual-band detector which combined PπMN structure and unipolar barrier was developed based on type-II InAs/GaSb superlattice. A relevant 320 × 256 focal plane array (FPA) was fabricated. Unipolar barrier and PπMN structure in our dual band detector structure were used to suppress cross-talk and dark current, respectively. The two channels, with respective 50% cut-off wavelength at 4.5 μm and 10 μm were obtained. The peak quantum efficiency (QE) of mid wavelength infrared (MWIR) band and long wavelength infrared (LWIR) band are 53% at 3.2 μm under no bias voltage and 40% at 6.4 μm under bias voltage of −170 mV, respectively. And the dark current density under 0 and −170 mV of applied bias are 1.076 × 10⁻⁵ A/cm² and 2.16 × 10⁻⁴ A/cm². The specific detectivity of MWIR band and LWIR band are 2.15 × 10¹² cm·Hz^1/2/W at 3.2 μm and 2.31 × 10¹⁰ cm·Hz^1/2/W at 6.4 μm, respectively, at 77 K. The specific detectivity of LWIR band maintains above 10¹⁰ cm·Hz^1/2/W at the wavelength range from 4.3 μm to 10.2 μm under −170 mV. The cross-talk, selectivity parameter at 3.0 μm, about 0.14 was achieved under bias of −170 mV. Finally, the thermal images were taken by the fabricated FPA at 77 K.     

Evaluation of the dosimetric characteristics of a radiophotoluminescent glass dosimeter for high-energy photon and electron beams in the field of radiotherapy

We aimed to evaluate the suitability of a glass dosimeter (GD) for high-energy photon and electron beams in experimental and clinical use, especially for radiation therapy. We examined the expanded dosimetric characteristics of GDs including dose linearity up to 500 Gy, uniformity among GD lots and for individual GDs, the angular dependence, and energy dependence of 4 therapeutic x-ray qualities. In addition, we measured the dosimetric features (dose linearity, uniformity, angular dependence, and energy dependence) of the GD for electron beams of 10 different electron energy qualities. All measurements with the exception of dose linearity for photon beam were performed in a water phantom. For high-energy photon beams, dose linearity has a linear relationship for a dose ranging from 1 to 500 Gy with the coefficient of determination; R² of 0.998. The uniformity of each GD of dose measurements was within ±0.5% for four GD lots and within ±1.2% for 80 GDs. In terms of the effects of photon beam angle, lower absorbed doses of within 1.0% were observed between 60° and 105° than at 90°. The GD energy dependence of 4 photon beam energy qualities was within ±2.0%. On the other hand, the result of the dose linearity for high-energy electron beams showed well fitted regression line with the coefficient of determination; R² of 0.999 between 6 and 20 MeV. The uniformity of GDs exposed to the nominal electron energies 6, 9, 12, 16, and 20 MeV was ±1.2%. In terms of the angular dependence to electron beams, absorbed doses were within 2.0% between 60° and 105° than at 90°. In evaluation of the energy dependence of the GD at nominal electron energies between 5 and 20 MeV, we obtained responses between 1.1% and 3.5% lower than that for a cobalt-60 beam. Our results show that GDs can be used as a detector for determining doses when a high-energy photon beam is used, and that it also has considerable potential for dose measurement of high-energy electron beam.     

Thin TiO2 grown by metal–organic chemical vapor deposition on (NH4)2S x -treated InP

The electrical characteristics of thin TiO₂ films prepared by metal–organic chemical vapor deposition grown on a p-type InP substrate were studied. For a TiO₂ film of 4.7 nm on InP without and with ammonium sulfide treatment, the leakage currents are 8.8×10⁻² and 1.1×10⁻⁴ A/cm² at +2 V bias and 1.6×10⁻¹ and 8.3×10⁻⁴ A/cm² at −2 V bias. The lower leakage currents of TiO₂ with ammonium sulfide treatment arise from the improvement of interface quality. The dielectric constant and effective oxide charge number density are 33 and 2.5×10¹³ cm², respectively. The lowest mid-gap interface state density is around 7.6×10¹¹ cm⁻² eV⁻¹. The equivalent oxide thickness is 0.52 nm. The breakdown electric field increases with decreasing thickness in the range of 2.5 to 7.6 nm and reaches 9.3 MV/cm at 2.5 nm.     

Effect of nitrogen ions on the structural,optical, and thermal properties of polyvinyl alcohol/starch blend

This work examines the properties of polyvinyl alcohol (PVA)/starch film containing glycerol as a plasticizer under exposure to different nitrogen ion fluence. The prepared PVA/starch blend was irradiated with ion fluence from 3 × 10¹⁷ to 12 × 10¹⁷ ions.cm⁻². From FTIR, the ion beam irradiation attack and weakens the C–H bond in PVA/starch blend. From XRD findings, the crystallite size of the blend decreased at 3 × 10¹⁷ ions/cm² while it increased at higher fluence up to 9 × 10¹⁷ ions/cm². This indicates the degradation of the blend at low ion fluence compared to crosslinking at high ion fluence. Also, the optical bandgap of the blend was decreased with an increase in ion fluence. Furthermore, the effect of N⁺ ions on some optical dispersion parameters is studied. The thermal stability of the PVA/starch blend shows a decrease in thermal stability upon irradiation with 3 × 10¹⁷ ions/cm² compared to higher thermal stability at higher doses up to 9 × 10¹⁷ ions/cm².