Highly sensitive electrochemical detection of dopamine and uric acid on a novel carbon nanotube-modified ionic liquid-nanozeolite paste electrode

A novel biosensor has been constructed by incorporating modified nanosized natural zeolite and 3-hydroxypropanaminium acetate (HPAA) as a novel room temperature ionic liquid, supported on multiwalled carbon nanotube (MWCNTs) and employed for the simultaneous determination of dopamine (DA) and uric acid (UA). A detailed investigation by transmission electron microscopy and electrochemistry is performed in order to elucidate the preparation process and properties of the composites. The voltammetric studies using the modified carbon paste electrode show two well-resolved anodic peaks for DA and UA with a potential difference of 160 mV, revealing the possibility of the simultaneous electrochemical detection of these compounds. The modified carbon paste electrode shows good conductivity, stability, and extraction effect due to the synergic action of HPAA, MWCNTs, and iron ion-doped natrolite zeolite. Under optimized conditions, the peak currents are linear from 8.12?×?10^?7 to 3.01?×?10^?4?mol?L^?1 and from 9.31?×?10^?7 to 3.36?×?10^?4?mol?L^?1 with detection limits of 1.16?×?10^?7 and 1.33?×?10^?7?mol?L^?1 for DA and UA using the differential pulse voltammetric method, respectively. Finally, the modified carbon paste electrode proved to have good sensitivity and stability and is successfully applied for the simultaneous determination of DA and UA in human blood serum and urine samples.     

Voltammetric sensor for simultaneous determination of ascorbic acid,acetaminophen, and tryptophan in pharmaceutical products

A novel carbon paste electrode modified with carbon nanotubes and 5-amino-2′-ethyl -biphenyl-2-ol was fabricated. The electrochemical study of the modified electrode, as well as its efficiency for electrocatalytic oxidation of ascorbic acid (AA), is described. The electrode was employed to study the electrocatalytic oxidation of AA, using cyclic voltammetry, chronoamperometry, and square-wave voltammetry (SWV) as diagnostic techniques. It has been found that the oxidation of AA at the surface of modified electrode occurs at a potential of about 250 mV less positive than that of an unmodified carbon paste electrode. SWV exhibits a linear dynamic range from 2.0?×?10^?7 to 5.0?×?10^?4 M and a detection limit of 1.0?×?10^?7 M for AA. In addition, this modified electrode was used for simultaneous determination of AA, acetaminophen (AC), and tryptophan (TRP). Finally, the modified electrode was used for determination of AA, AC, and TRP in pharmaceutical products.     

Selective determination of catecholamine in the presence of ascorbic acid or uric acid on the membrane of silver nanoparticles/poly l-phenylalanine

The silver ions and l-phenylalanine were co-deposited and formed a hybrid membrane on the surface of glassy carbon electrode by cyclic voltammetry. The membrane had good properties for catalyzing the redox of catecholamine neurotransmitters, including epinephrine (EP), norepinephrine (NE), and dopamine (DA). The electrochemical behaviors of these neurotransmitters were studied on this modified electrode. and therefore, an assay for each of them is set up and the detection limits for EP, NE, and DA are 7.2?×?10^?9, 6.4?×?10^?9, and 8.5?×?10^?9 mol L^?1, respectively. The proposed method can effectively eliminate the interference of the ascorbic acid and uric acid. The conditions which influenced the analyses were optimized. Using this method to determine the content of EP, NE, and DA in injections, the results were satisfactory.     

Benzoylferrocene-modified carbon nanotubes paste electrode as a voltammetric sensor for determination of hydrochlorothiazide in pharmaceutical and biological samples

The electrooxidation of hydrochlorothiazide (HCT) at the surface of a benzoylferrocene modified multi-walled carbon nanotube paste electrode was studied using electrochemical approaches. Under the optimized conditions (pH 7.0), the square wave voltammetric peak current of HCT increased linearly with HCT concentration in the ranges of 6.0?×?10^?7 to 3.0?×?10^?4 M. The detection limit was 9.0?×?10^?8 M HCT. The diffusion coefficient (D?=?1.75?×?10^?5 cm²/s) and electron transfer coefficient (α?=?0.45) for HCT oxidation were also determined. The proposed sensor was successfully applied for the determination of HCT in human urine and tablet samples.     

Electrochemical methods for determination of thymine in medical pipefish samples based on HPMαFP/Ppy/GCE-modified electrode

A sensitive electrochemical method was developed for the voltammetric determination of thymine at a composite film-modified electrode 1-phenyl-3-methyl-4-(2-furoyl)-5-pyrazolone (HPMαFP)/polypyrrole (Ppy)/glassy carbon electrode (GCE). The electrochemical parameters of thymine were investigated by cyclic voltammetry and differential pulse voltammetry. In pH?=?7.4, one sensitive oxidation peak of thymine with E _pa?=?0.968 V was observed on the HPMαFP/PPy-modified electrode. The difference of peak potential (?E _pa) was 188 mV lower than that for bare GCE. Compared to the bare GCE and Ppy/GCE, the HPMαFP/Ppy/GCE-modified electrode showed an excellent electrocatalytic effect on the oxidation of thymine and displayed a shift of the oxidation potential in the negative direction with significant increase in the peak current. Under the optimum condition, the concentration calibration range and detection limit are 2?×?10^?6–1?×?10^?4 and 4.85?×?10^?7?M for thymine. This developed method had been applied to the direct determination of thymine in medical pipefish samples with satisfactory results.     

Effect of annealing temperature on optical and electrochemical properties of chitosan–ZnO nanostructure

Chitosan–ZnO nanostructures were prepared by chemical precipitation method using different concentration of zinc chloride and sodium hydroxide solutions. Nanorod-shaped grains with hexagonal structure for samples annealed at 300 °C and porous structure with amorphous morphology for samples annealed at 600 °C were revealed in SEM analysis. X-ray diffraction patterns confirmed the hexagonal phase ZnO with crystallite size found to be in the range of ~24.15–34.83 nm. Blue shift of UV–Vis absorption shows formation of nanocrystals/nanorods of ZnO with marginal increase in band gap. Photoluminescence spectra show that blue–green emission band at 380–580 nm. The chitosan–ZnO nanostructures used on surface of a glassy carbon electrode gives the oxidation peak potential at ~0.6 V. The electrical conductivity of chitosan–ZnO composites were observed at 2.1?×?10^?5 to 2.85?×?10^?5?S/m. The nanorods with high surface area and nontoxicity nature of chitosan–ZnO nanostructures observed in samples annealed at 300 °C were suitable as a potential material for biosensing.     

The first electrochemical sensor for determination of mangiferin based on an ionic liquid–graphene nanosheets paste electrode

A novel carbon paste electrode modified with graphene nanosheets and an ionic liquid (n-hexyl-3-methylimidazolium hexafluoro phosphate) was fabricated and used for the electrochemical study of mangiferin for the first time. This modified electrode offers a considerable improvement in voltammetric sensitivity toward mangiferin, compared to the bare electrode. Square wave voltammetry (SWV) exhibits a linear dynamic range from 5.0?×?10^?8 to 2.0?×?10^?4 M and a detection limit of 20.0 nM for mangiferin. Finally, the proposed method was successfully applied to the determination of mangiferin in real samples such as serum and urine.     

A selective sensor for nanolevel detection of lead (II) in hazardous wastes using ionic-liquid/Schiff base/MWCNTs/nanosilica as a highly sensitive composite

An effective potentiometric sensor had been fabricated for the rapid determination of Pb²⁺ based on carbon paste electrode consisting of room temperature ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF₆), multiwalled carbon nanotubes (MWCNTs), nanosilica, synthesized Schiff base, as an ionophore, and graphite powder. The constructed nanocomposite electrode showed better sensitivity, selectivity, response time, response stability, and lifetime in comparison with typical Pb²⁺ carbon paste electrode for the successfully determination of Pb²⁺ ions in water and in waste water samples. The best response for nanocomposite electrode was obtained with electrode composition of 18% ionophore, 20% BMIM-PF₆, 49% graphite powder, 10% MWCNT, and 3% nanosilica. The new electrode exhibited a Nernstian response (29.76?±?0.10 mV decade^?1) toward Pb²⁺ ions in the range of 5?×?10^?9?C1.0?×?10^?1 mol L^?1 with a detection limit of 2.51?×?10^?9 mol L^?1. The potentiometric response of prepared sensor is independent of the pH of test solution in the pH range of 4.5?C8.0. It has quick response with response time of about 6 s. The proposed electrode show fairly good selectivity over some alkali, alkaline earth, transition, and heavy metal ions.     

Enhanced electrocatalytic oxidation of hydroxylamine on Pt/polypyrrole composite modified glassy carbon electrode

A sensitive hydroxylamine sensor is developed by electrodeposition of Pt nanoparticles on pre-synthesized polypyrrole nanoparticles modified glassy carbon electrode. The modified electrode presents distinctly electrocatalytic activity toward hydroxylamine oxidation. The kinetic parameters such as the overall numbers of electrons involved in hydroxylamine oxidation, the electron transfer coefficient, standard heterogeneous rate constant, and diffusion coefficient are evaluated. The current response increases linearly with increasing hydroxylamine concentrations and exhibits two wide linear ranges of 5.0?×?10^?7–1.1?×?10^?3 and 1.1?×?10^?3–18.8?×?10^?3 M with a detection limit of 0.08 μM (s/n?=?3). The proposed electrode presents excellent operational and storage ability for determining hydroxylamine. Moreover, the sensor shows good sensitivity, selectivity, and reproducibility properties.     

Gelatin-HCl biomembranes with ionic-conducting properties

Gelatin-HCl protonic gel polymer electrolytes were obtained by crosslinking with formaldehyde in the presence of hydrochloric acid and glycerol as plasticizer and characterized in present study. The ionic conductivity measurements revealed the best value of 5.35?×?10^?5 S cm^?1 at room temperature. Factorial design analysis showed that influence of glycerol is more pronounced than influence of acid on ionic conductivity values. Moreover, the 90 % transparent membranes evidenced a linear increase of ionic conductivity values of 5.35?×?10^?5 S cm^?1 at 26.5 °C to 5.77?×?10^?4 S cm^?1 at 82.8 °C following Arrhenius type mechanism of charge mobility.     

Enhancement in electrochemical properties of ionic liquid-based nanocomposite polymer electrolytes by 100 MeV Si9+ swift heavy ion irradiation

Swift heavy ion (SHI) irradiation has been used as a tool to enhance the electrochemical properties of ionic liquid-based nanocomposite polymer electrolytes dispersed with dedoped polyaniline (PAni) nanorods; 100 MeV Si⁹⁺ ions with four different fluences of 5?×?10¹⁰, 1?×?10¹¹, 5?×?10¹¹, and 1?×?10¹² ions cm^?2 have been used as SHI. XRD results depict that with increasing ion fluence, crystallinity decreases due to chain scission up to fluence of 5?×?10¹¹ ions cm^?2, and at higher fluence, crystallinity increases due to cross-linking of polymer chains. Ionic conductivity, electrochemical stability, and dielectric properties are enhanced with increasing ion fluence attaining maximum value at the fluence of 5?×?10¹¹ ions cm^?2 and subsequently decrease. Optimum ionic conductivity of 1.5?×?10^?2 S cm^?1 and electrochemical stability up to 6.3 V have been obtained at the fluence of 5?×?10¹¹ ions cm^?2. Ac conductivity studies show that ion conduction takes place through hopping of ions from one coordination site to the other. On SHI irradiation, amorphicity of the polymer matrix increases resulting in increased segmental motion which facilitates ion hopping leading to an increase in ionic conductivity. Thermogravimetric analysis (TGA) measurements show that SHI-irradiated nanocomposite polymer electrolytes are thermally stable up to 240–260 °C.     

Voltammetric determination of hydroxylamine in water samples using a 1-benzyl-4-ferrocenyl-1H-[1,2,3]-triazole/carbon nanotube-modified glassy carbon electrode

A modified glassy carbon electrode has been constructed using a 1-benzyl-4-ferrocenyl-1H-[1,2,3]-triazole along with multiwalled carbon nanotubes. The electrochemical behaviour of modified electrode has been investigated by cyclic voltammetry. Electrocatalytic activity of the modified electrode was investigated for the oxidation of hydroxylamine in 0.1 M phosphate-buffered solution of pH 8. The modified electrode showed electrocatalytic response to the oxidation of hydroxylamine at the potential of 330 mV. The linear range and detection limit for the detection of hydroxylamine in the optimum condition were found to be 4.0?×?10^?7 to 6.75?×?10^?4 M and 28.0?±?1.0 nM, respectively. Finally, the method was employed for the determination of hydroxylamine in water samples.     

Electrochemical and catalytic investigations of epinephrine,acetaminophen and folic acid at the surface of titanium dioxide nanoparticle-modified carbon paste electrode

In the present paper, the use of a carbon paste electrode modified with 1-(4-(1, 3-dithiolan-2-yl)-6, 7-dihydroxy-2-methyl-6, 7-dihydrobenzofuran-3-yl)ethanone (DDE) and TiO₂ nanoparticles prepared by a simple and rapid method was described. The modified electrode showed excellent properties for electrocatalytic oxidization of epinephrine (EP), acetaminophen (AC) and folic acid (FA). The apparent charge transfer rate constant, k _s?=?1.14 s^?1, and transfer coefficient, α?=?0.54, for electron transfer between the modifier and carbon paste electrode were calculated. It has been found that under optimum condition (pH?=?7.0) in cyclic voltammetry, the oxidation of EP occurs at a potential about 280 mV less positive than that of an unmodified carbon paste electrode. The values of transfer coefficients (α?=?0.46), catalytic rate constant (k?=?1.2?×?10⁴ M^?1 s^?1) and diffusion coefficient (D?=?2.70?×?10^?5 cm² s^?1) were calculated for EP. Differential pulse voltammetry (DPV) exhibited two linear dynamic ranges of 0.5 to 50.0 μM and 50.0 to 1,000 μM for EP. This modified electrode is quite effective not only for the detection of EP, AC and FA but also for the simultaneous determination of these species in a mixture. The limit of detection for EP, AC and FA is 0.10, 1.80 and 2.36 μM, respectively.     

Influences of interfacial adhesion on gas barrier property of functionalized graphene oxide/ultra-high-molecular-weight polyethylene composites with segregated structure

The segregated graphene oxide(GO)/ultra-high-molecular-weight polyethylene (UHMWPE) composite films with various interfacial adhesion property were prepared by mechanical blending method from UHMWPE, GO, dodecyl amine (DA) functionalized graphene oxide(DA–GO) or uniform DA–GO/high density polyethylene (DA–GO/HDPE) powder. The results of XRD and XPS indicated that DA chain was successfully grafted onto GO sheets via a chemical method, which enhanced the interfacial adhesion between UHMWPE particles and GO sheets. The characterizations of POM and SEM proved that good segregated structure was only obtained in DA–GO/UHMWPE or DA–GO/HDPE/UHMWPE composite. Strong interfacial adhesion between fillers and matrix exhibits positive effect on gas barrier property. Compared to the GO/UHMWPE composite film, dramatic decrease in O₂ permeability coefficient by 42.2 and 48.1%, from 15.4 × 10^?14 to 8.9 × 10^?14 and 8.0 × 10^?14 cm³ cm cm^?2 s^?1 Pa^?1, is achieved upon the addition of only 0.5 wt% fillers, respectively. The DSC results demonstrated that the enhanced gas barrier performance was ascribed to the strong interfacial adhesion between DA–GO/HDPE and UHWMPE matrix, rather than the crystallinity of UHWMPE matrix. Additionally, the decrease in UHMWPE particle size might be conducive to improving the gas barrier property of composite films due to the formation of more isolation layers perpendicular to the film plane.     

50 MeV Li3+ ion irradiation effect on structural, electrical, and dielectric properties of PVA-based nanocomposite polymer electrolytes

Nanocomposite polymer electrolyte thin films of polyvinyl alcohol (PVA)-orthophosphoric acid (H₃PO₄)-Al₂O₃ have been prepared by solution cast technique. Films are irradiated with 50 MeV Li³⁺ ions having four different fluences viz. 5?×?10¹⁰, 1?×?10¹¹, 5?×?10¹¹, and 1?×?10¹² ions/cm². The effect of irradiation on polymeric samples has been studied and characterized. X-ray diffraction spectra reveal that percent degree of crystallinity of samples decrease with ion fluences. Glass transition and melting temperatures have been also decreased as observed in differential scanning calorimetry. A possible complexation/interaction has been shown by Fourier transform infrared spectroscopy. Temperature-dependent ionic conductivity shows an Arrhenius behavior before and after glass transition temperature. It is observed that ionic conductivity increases with ion fluences and after a critical fluence, it starts to decrease. Maximum ionic conductivity of ～2.3?×?10^?5 S/cm owing to minimum activation energy of ～0.012 eV has been observed for irradiated electrolyte sample at fluence of 5?×?10¹¹ ions/cm². The dielectric constant and dielectric loss also increase with ion fluences while they decrease with frequency. Transference number of ions shows that the samples are of purely ionic in nature before and after ion irradiation.     

Evaluation of carbon-supported copper phthalocyanine (CuPc/C) as a cathode catalyst for fuel cells using Nafion as an electrolyte

Carbon-supported copper phthalocyanine (CuPc/C) nanoclusters, as a novel suitable cathode catalyst in polymer electrolyte membrane fuel cells, have been synthesized via a combined solvent impregnation and milling procedure along with high-temperature treatment. For optimizing the electrocatalytic activity of the catalyst obtained, the electrode with varying Nafion ionomer contents in the catalyst layer was screened by cyclic voltammetry and linear sweep voltammetry employing a rotating disk electrode technique to investigate the effect of Nafion ionomer as for alkaline electrolyte. For comparative purposes, electrode with various contents of available anion-ionomer was also investigated. The results revealed that the content of Nafion ionomer can affect the oxygen reduction reaction activity of the CuPc/C catalyst and an optimal content of Nafion ionomer was around 3.5?×?10¹?μg?cm^?2, which corresponds well with the electrode prepared using available anion-ionomer. The electrode prepared using Nafion ionomer can produce a comparable performance to that of using available anion-ionomer, giving an onset potential at 0.1 V with a half-wave potential of ?0.03 V. Furthermore, Koutechy–Levich analysis showed that the value of electron transfer number is in the range of 3.40 to 3.74 when using electrode with varying Nafion ionomer contents from 2.5?×?10¹ to 1.6?×?10²?μg?cm^?2. The membrane electrode assembly fabricated with the CuPc/C cathode catalyst with a loading of 3.6 mg?cm^?2 and a Nafion membrane immersed in 3 M KOH for 48 h produced a power density of 3.8 mW?cm^?2 at room temperature.     

Voltammetric behaviors of an emerging pollutant benzotriazole on multiwall carbon nanotubes (MWNTs)—Nafion modified electrode in various pH mediums

The electrochemical behaviors of an emerging pollutant, benzotriazole (BTA), at multiwall carbon nanotubes and Nafion modified glassy carbon electrode (MWNTs-Nafion/GCE) were investigated systematically. The electrochemical reduction of BTA was significantly improved by MWNTs-Nafion compared to bare GCE, ascribed to the excellent adsorption capacity and electrocatalytic activity of MWNTs. BTA presented well-defined reduction peaks only at pH <3.0, suggesting the involvement of lots of protons in the reduction process. Peak potential shifted negatively and peak current decreased significantly with pH increase. BTA showed various UV–Vis absorption spectra in acidic and alkaline mediums. Cathodic peak current increased linearly with square root of sweep rate as well as with the concentration of BTA from 3.0?×?10^?6 to 1.6?×?10^?4 mol L^?1. This suggests a diffusion-controlled and irreversible electrode process. Diffusion coefficient of BTA on MWNTs-Nafion/GCE was obtained as 2.67?×?10^?2 cm² s^?1 with four orders of magnitude larger than that on GCE. MWNTs-Nafion/GCE showed a good selectivity between BTA and O₂ but poor selectivity between BTA and tolyltriazole.     

Ultrasonic preparation of tetraoxalyl ethylenediamine melamine resin-coated multiwalled carbon nanotubes for trace Ni(II) sensing

Under an aid of ultrasonic, tetraoxalyl ethylenediamine melamine resin-coated multiwalled carbon nanotubes were prepared for Ni(II) sensing in aqueous solution. The processes involved the fabrication of tetraoxalyl ethylenediamine melamine resin by one pot way, the coating of tetraoxalyl ethylenediamine melamine resin at multiwalled carbon nanotubes (MWCNTs), and the determination of Ni(II). The present materials were carefully examined by Fourier transform infrared spectroscopy, field emission scanning electron microscope, and electrochemistry techniques. A great deal of amorphous microsphere could be observed for tetraoxalyl ethylenediamine melamine resin with an average diameter of 1.2 μm, and MTE could evenly adhere at the surface of MWCNTs by the ultrasonic. Tetraoxalyl ethylenediamine melamine resin-coated multiwalled carbon nanotube-modified paraffin-impregnated graphite electrode was successfully used for the determination of Ni(II) by differential pulse adsorptive anodic stripping voltammetry. The current responses (?0.3 V) were linearly increased depending on the concentration from 1?×?10^?11 to 3?×?10^?10 M (i (μA)?=?11.1?+?7.9 c (1?×?10^?12 M); R?=?0.9901, 3σ?=?7?×?10^?12 M).     

Selective Fluorescence Sensing of Deoxycytidine 5��-Monophosphate (dCMP) Employing a Bis(diphenylphosphate)diimine Ligand

A new bis(diphenylphosphate)diimine ligand (BP1) was prepared and evaluated for its ability for selective detection of deoxycytidine 5??-monophosphate (dCMP). BP1 exhibited off-type fluorescence in the presence of dCMP. The fluorescence of BP1 was significantly quenched upon the addition of 2.5?×?10^?4 M dCMP and the detection limit was 1.25?×?10^?5 M in MeCN-H₂O (1:1, v/v). The binding ratio between BP1 and dCMP was determined to be 1:1 with the binding constant of 3.98?±?0.60?×?10^?3 M^?1.     

Sensitive and selective electrochemical sensor for magnolol based on the enhancement effect of multiwalled carbon nanotubes

Herein, insoluble multiwalled carbon nanotubes (MWNTs) were dispersed into N,N-dimethylformamide (DMF) via ultrasonication, resulting in a stable and homogeneous MWNTs suspension. After evaporation of DMF, the surface of glassy carbon electrode was successfully coated with MWNTs film, as confirmed from scanning electron microscopy measurements. In pH 7 phosphate buffer, an irreversible oxidation peak was observed for magnolol, and the peak currents greatly increased on MWNTs film surface. The influences of pH value, amount of MWNTs and accumulation conditions were studied. Based on the remarkable enhancement effect of MWNTs, a new electrochemical sensor with high sensitivity was developed for magnolol. The linear range was from 5 μg?L^?1 to 1 mg?L^?1, and the detection limit was 2 μg?L^?1 (7.51?×?10^?9?M) after a 3-min accumulation. This novel sensor was successfully used to detect the content of magnolol in Chinese traditional medicines, and the recovery was over the range from 98.1 to 99.1 %.