催化剂比例对单壁碳纳米管制备的影响

采用电弧放电法以Y/Ni为催化剂制备了单壁碳纳米管 ,研究了不同催化剂比例对制备产物的影响。获得了不同激发波长下 (476 5～ 1 0 6 4nm)单壁碳纳米管的拉曼光谱 ,采用图表法对径向呼吸模的谱峰进行了认定。结果表明 :样品中碳管的直径分布在 1 2～ 1 6nm之间 ,直径在 1 43nm附近的碳管居多。催化剂的比例只是影响碳管的产额 ,对其直径分布的影响很小     

以Y/Ni为催化剂制备的单壁碳纳米管的拉曼光谱研究

采用电弧放电法以Y/Ni为催化制备了单壁碳纳米管（SWNTs），对样品进行了扫描电镜、透射电镜和拉曼光谱的研究。所制备的样品中单壁碳纳米管的含量较高。对单壁碳纳米管的共振拉曼散射增强效应进行了观察，随激光波长的不同，单壁碳纳米管的拉曼光谱也随之变化，尤其是低频区径向呼吸模的变化比较明显。利用布里渊区折叠法计算了单壁碳纳米管的电子态密度曲线，根据SWNTs电子态密度尖峰之间的能量差、管子的直径和呼吸模频率建立了一个图表，并对SWNTs的呼吸模进行了归属。分析结果表明：样品中单壁碳纳米管的直径分布在0.79-1.76nm范围，金属管和半导体管均存在，并且直径在1.45nm附近的碳管居多。     

对PECVD制备碳纳米管的研究和探讨

高纯度和高产率的制备碳纳米管是碳纳米管研究的一个重点。目前制备碳纳米管的方法有电弧法、激光蒸发法、化学气相沉积法(又称CVD法)和模板法等。本文主要介绍采用PECVD化学气相沉积法制备碳纳米管,并对该种方法制备碳纳米管进行了系统的研究和探讨。     

酞菁裂解法多壁碳纳米管的制备、表征和应用

为了探究高温处理酞菁钴对O2 的催化还原作用 ,以酞菁钴作为催化剂的前体 ,通过化学气相沉积的方法 ,在 85 0℃下 ,氩气与氢气混合气流中 ,制备了双层定向碳纳米管 ,纳米管的直径分布在 6 0～ 12 0nm ,长度约为4 0 μm ,在纳米碳管中包裹有直径为 10nm的钴颗粒 .所得产品用透射电子显微镜和扫描电子显微镜进行了观察 ,并用拉曼谱和X射线衍射对样品进行了表征 .通过循环伏安法测量得到纳米碳管对金属颗粒在酸性溶液中的腐蚀具有一定抵抗作用 .认为少量的N对于竹节状碳纳米管的形成和金属对酸的抵抗作用是十分必要的 ,每节中碳壁的弯曲弧度则与N在碳纳米管中含量和N与金属的相互作用有关 .另外 ,碳纳米管较大的电化学活性区域在电化学方面具有潜在的应用价值 .     

非晶碳化硅材料与光学微腔的制备与发光

利用等离子体化学气相沉积技术在100℃的衬底温度下,制备了具有不同组分比的系列非晶碳化硅薄膜。结合傅里叶变换红外光谱与喇曼光谱对所制备的薄膜微结构进行了表征与分析,同时,对具有不同组分比的非晶碳化硅薄膜室温光致发光性质进行了系统的研究。结果表明在Ar⁺离子激光和Xe灯紫外光的激发下,不同组分的样品显示出不同的光致发光特性,并对样品的发光特性与其微结构的联系进行了讨论。在此基础上,用碳化硅薄膜设计和制备了全固体光学微腔,研究了微腔对碳化硅发光行为的调制作用。     

微喇曼和红外光谱法研究化学气相沉积金刚石多晶膜结晶质量特性

研究了化学气相沉积多晶膜的宏观性能（颜色和透光性）与微观性能（结晶质量、相纯度和氢杂质含量）之间的关系,喇曼谱与金刚石膜中氢杂质含量（红外光谱测得）的关联性.给出了根据颜色和透明度来区分样本膜质量的实验依据,颜色较深的膜的结晶质量差、相纯度低、氢杂质含量高,1 332 cm－1金刚石特征喇曼峰强度低,半峰宽大.由于多晶膜生长不均匀性、多晶以及粗糙度的影响,生长面的微喇曼光谱随采样点变化会产生较大的偏差,而光滑生长界面的喇曼光谱随采样点的变化偏差较小,因此生长界面的喇曼光谱更能反映化学气相沉积法制备金刚石膜的整体质量.     

用微米级LaNi5为催化剂生长的碳管的ESR谱研究

用微米级LaNi₅合金粉末为催化剂, 以乙炔为原料, 采用化学气相沉积(CVD)法合成了多壁碳纳米管. 在100~290 K温度下测量了41 μm≤d≤150 μm粒径催化剂制备的不同直径分布的碳纳米管的电子自旋共振（ESR）谱,研究了测量温度、微米级催化剂粒径及制备过程的氢气氛对生成的碳纳米管的ESR谱线型、g因子、线宽的影响. 发现碳纳米管的g因子随其直径的增大而增大,分别为2.040 0（催化剂粒径41 μm≤d≤50 μm, 碳纳米管的直径分布为10 nm到20 nm）和2.089 8（催化剂粒径100 μm≤d≤150 μm,碳纳米管的直径分布为70 nm到120 nm）. 发现小管径纳米管的ESR谱图有一个峰, 而大管径纳米管的ESR谱图有两个峰A和B, 且随测量温度的升高, 峰B强度增大.     

高质量单壁纳米碳管的CVD法合成及催化剂酸碱性对碳管生长的影响

采用燃烧法制备了Fe/Mo/MgO催化剂,用化学气相沉积法在1000℃下催化裂解甲烷制得了单壁纳米碳管.实验结果表明,550℃下焙烧的催化剂效果最好,适宜的酸碱性应该是催化剂具有较高活性的原因.用扫描电镜、透射电镜、高分辨透射电镜、热重分析和拉曼光谱等方法对制备的纳米碳管粗产品进行了表征.结果表明,该产物确为高质量单壁纳米碳管,其形态基本都以束状存在,且单壁纳米碳管直径分布较窄(0.85～1.22nm);对反应气氛的考察表明,CH4/N2=50/300为最佳,该气氛下所制得粗产物中单壁碳管的含量接近40%,经稀盐酸室温处理后,碳管含量可达到75%以上.     

纳米碳管的制备及其场发射性能研究

将Ni(NO3)2-Mg(NO3)2体系作为催化剂前驱体,在不同气源比例下用CVD催化裂解法制备纳米碳管,用SEM、TEM和喇曼光谱对其进行了表征和分析,制备出完整性好的纳米碳管.再用两种工艺和配方制备其场发射阴极,对阴极样品进行了场发射性能测试.结果表明,经过氢处理在Si基上制备的CNT阴极发光效果好,且具有良好的场发射性能.     

非晶微晶过渡区域硅薄膜的微区喇曼散射研究

通过改变氢气对硅烷气体的稀释程度,并保持其他的沉积参量不变,用等离子体增强化学气相沉积(PECVD)方法成功地制备出处于非晶微晶相变过渡区域的硅薄膜样品.测量了样品的室温光电导和暗电导,样品的光电性能优越,在50mW·cm-2的白光照射下,光电导和暗电导的比值达到106.在室温下用微区喇曼谱研究了薄膜的微结构特性,用高斯函数对喇曼谱进行了拟合分析.结果表明,在我们的样品制备条件下,当H2和SiH4的流量比R较小时,样品表现出典型的非晶硅薄膜的结构特性;随流量比R的增大,薄膜表现出两相结构,其中的微晶成分随 关键词： 非晶硅 薄膜 喇曼散射 微结构     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.