Fast and effective sample preparation for determination of organochlorine compounds in fatty tissue of marine mammals using microwave extraction

Summary A rapid and effective method is described for the extraction of organochlorine compounds (PCB 153, PCB 138, PCB 180, p,p-DDE, -HCH, -HCH, -HCH and HCB) from seal blubber and pork fat withn-hexane using a microwave technique. Heating of the non-polarn-hexane was achieved using a microwave transformer. The lipid content of the samples obtained by this extraction was identical to that by Soxhlet extraction. After separation of sample matrix and organochlorines on a silica gel column the organochlorine compounds were determined by GC-ECD. The efficiency of the method was tested with 500 mg spiked fat, extracted using various numbers of extraction cycles. Recoveries of organochlorine compounds in grey seal blubber and spiked pork fat generally exceeded 90 %.     

Voltammetric determination of copper and lead in gasoline using sample preparation as microemulsions.

A voltammetric method for the determination of Cu(II) and Pb(II) in gasoline using sample preparation as three-component solutions (gasoline:propan-1-ol:water, 25:60:15 v/v/v) is proposed. HNO(3) was employed as a supporting electrolyte and to allow the use of aqueous inorganic standards for calibration, even if the analyte species originally in gasoline is present as a metallo-organic form. A square-wave anodic sequential determination was used by measuring the stripping current of Cu(II) (at +104 mV) using a glassy carbon electrode (GCE) and, in a second run, measuring the Pb(II) stripping current (at -470 mV) using a bismuth-film deposited on the surface of the GCE. The method allowed the quantification of 1.7 x 10(-9) mol L(-1) of Cu and 1.4 x 10(-10) mol L(-1) of Pb employing a 1500-s accumulation time. Recovery tests using analyte spiked three-component solutions prepared with commercial gasoline samples enabled recoveries of Cu and Pb from 97 +/- 8 to 102 +/- 5%.     

Simplified sample preparation for fluoride determination in biological material

A simple and rapid preparation method for the determination of fluoride in biological materials (blood and food) of various origins, is described. A homogenized sample was placed in a plastic diffusion cell and calcium phosphate added, it was then dried at 55 degrees C and treated with 70% HClO4 and 40% AgClO4. After digestion for 24 h at 55 degrees C, the fluorides released were fixed on the upper part of a diffusion cell containing a thin layer of NaOH. The analyses of the diffused fluoride were carried out with an ion-selective electrode. The proposed microdiffusion method, without mineralization, enables quantitative separation of the fluoride from the biological samples.     

Quantitative determination of nonylphenol polyethoxylate surfactants in marine sediment using normal-phase liquid chromatography-electrospray mass spectrometry.

A new comprehensive analytical method based on normal-phase liquid chromatography-electrospray ionization mass spectrometry (LC-ESI-MS) has been developed for the quantitative determination of individual nonylphenol ethoxylate (NPEO) surfactants in complex environmental matrices. Clean-up of sample extracts was performed on cyanopropyl silica solid-phase extraction cartridges. Complete NPEO oligomer separation was achieved by using normal-phase LC. Because the non-polar solvents used in normal-phase LC are incompatible with ESI, unique LC-ESI-MS interface conditions were adopted that provided a functional interface and also enhanced the detection response of NPEOs. These provided enhanced ESI signal intensity and stability and facilitated the detection of NPEOs as sodium adducts at parts-per-billion concentration levels. The overall analytical method was validated for accuracy and precision by analyzing sediment samples spiked with known amounts of NPEOs. The method is superior to those currently used for NPEO analysis (LC-UV, LC-fluorescence, LC-thermospray-MS, LC-field desorption-MS, LC-particle beam-MS and GC-MS) in terms of detection limits, specificity and speed of analysis. The validated method was successfully applied to determine levels of NPEOs in sediments from the Strait of Georgia, British Columbia. This work also demonstrates that by proper selection of normal-phase LC-ESI-MS interface conditions this technique is capable of solving separation problems which are not amenable with reversed-phase LC-ESI-MS.     

Iodine determination in biological materials Options for sample preparation and final determination

This paper describes the development of various new acid sample decomposition methods, as well as an extraction (leaching) method and compares them with the “Sch?niger Combustion” technique. The methods have been developed as sample preparation techniques for iodine determination in biological materials, especially in solid samples. ICP-MS (inductively coupled plasma mass spectrometry) and a catalytic technique are employed and discussed for the final determination of iodine concentrations. Accuracy and reliability of the different analytical methods are shown in the examples of different CRMs (certified reference materials) available for iodine. The results of an interlaboratory comparison are specifically presented for the extraction (leaching) method. Received: 11 May 1998 / Revised: 14 June 1998 / Accepted: 16 June 1998     

自动消解仪—ICP法测定水系沉积物中6种重金属元素

建立了自动消解仪-电感耦合等离子体发射光谱法(ICP-OES)同时测定水系沉积物中Cu、Zn、Ni、Cr、Pb、Co六种元素含量的方法。该方法的相关系数好、检出限低。方法经国家标准物质(GBW07361)验证,准确度和精密度均能达到环境监测分析的要求,为水系沉积物中重金属元素含量的测定提供了简单可靠的分析方法。     

Rapid sample preparation for the gas-chromatographic determination of methohexital in serum using reversed phase cartridges

Conclusion The proposed sample preparation for the gaschromatographic determination of methohexital in serum by using SEP-PAK C₁₈ cartridges is superior to the usual extraction by organic solvents because of its good reliability and practicability. Its main advantages are: 1) constantly high recovery; 2) complete removal of endogenous substances that might interfere with the determination resulting in a rather specific method; 3) ease of handling.

---

Schnelle Probenvorbereitung für die gas-chromatographische Bestimmung von Methohexital im Serum unter Verwendung von Reversed-Phase-Kartuschen

     

Automated sample preparation using supported liquid membranes for liquid chromatographic determination of sulfonylurea herbicides

Summary Sample preparation for determination of sulfonylurea herbicides in aqueous samples is investigated. The technique studied utilizes extraction and back extraction in an automated flow system and is coupled on-line to a liquid chromatographic system. The extraction unit consists of an immobilized liquid membrane, separating two aqueous phases. From the acidified donor phase the analytes are extracted into the organic solvent of the membrane. After traversing the membrane they are back extracted into an alkaline/neutral aqueous acceptor phase. They are trapped in the acceptor by dissociation, making them insoluble in the membrane.Studies of the sample preparation system concern factors like channel length of separators, distribution coefficients of analytes and use of a precolumn instead of loop for chromatographic injections. Effects of the internal diameter of the analytical column as well as the detection of the sulfonylurcas are investigated.     

Use of solid-phase extraction in various of its modalities for sample preparation in the determination of estrogens and progestogens in sediment and water.

The environmental analysis of estrogens and progestogens at physiologically active concentrations (low ng/l range) requires the use of very sensitive and selective methods, which, in most cases, make necessary an extraction/purification step. In this study, various procedures for the determination of several estrogens (estriol, estradiol, ethynyl estradiol, estrone, and diethylstilbestrol) and progestogens (progesterone, norethindrone, and levonorgestrel) in environmental matrices, including water and river sediment, are described. In all procedures, final analysis of the target compounds is performed by reversed-phase liquid chromatography-diode array detection-mass spectrometry, whereas sample preparation always includes a solid-phase extraction (SPE) step. For this SPE step. various types of sorbents, protocols, and devices have been used, and their respective advantages and disadvantages are discussed. For the off-line SPE of estrogens and progestogens from water samples, a syringe type cartridge LiChrolut RP-18 (500 mg) was selected out of two other sorbents--LiChrolut EN (200 mg) and Isolut ENV (500 mg)--for use with the automated sample preparation instrument ASPEC XL. For the on-line SPE and analysis of water samples the 10 mm x 2 mm I.D. HySphere-Resin-GP cartridge, was preferred to the C18 Baker, the PLRP-S, and the Oasis HLB. for use with the Prospekt system. A completely manual protocol based on the use of Sep-Pak C18 Plus cartridges was developed for purification of sediment extracts. All procedures were shown to be linear over a wide range of concentration, exhibited satisfactory repeatability and accuracy, and reached limits of detection usually in the low ng/l and ng/g range. Comparatively, the on-line method was shown to be advantageous in terms of automation and general method performance.     

Simplified sample preparation for GC speciation analysis of organotin in marine biomaterials

Two simple sample preparation methods for the speciation analysis of triphenyltin and butyltin compounds in marine biotissues, using tetramethylammonium hydroxide (TMAH) solubilization and enzymic hydrolysis, have been developed and compared with conventional acid digestion. Derivatization was carried out in situ using sodium tetraethylborate (NaBEt₄) without prior separation of the analytes from the tissue matrix. Separation and detection was performed using capillary gas chromatography (GC) coupled to microwave-induced plasma atomic emission spectrometry (MIP AE) allowing detection limits of 2 ng g^?1 (as tin) to be reached. The accuracy of the presented methods was demonstrated by the analysis of a fish reference material (NIES No. 11). the necessity for sample clean-up is discussed and examples of the analysis of mussel tissue are shown.     

Comparison of sample digestion procedures for the determination of arsenic in certified marine samples using the FI-HG-AAS-technique

 High-pressure digestion and a closed-vessel microwave heated system, both employing a mixture of nitric acid and hydrogen peroxide as digesting agent, were tested for decomposing the certified samples of BCR 278 mussel tissue (Mytilus edulis) and of BCR 422 cod muscle to determine arsenic by use of FI-HG-AAS. While the microwave system is insufficient to mineralize arsenic in marine samples (arsenic recoveries of 13±10% in BCR 278, 2±1% in BCR 422; n=4), high-pressure ashing at 300 °C results in recovery percentages of 56±15% (n=4) in mussel tissue (BCR 278) and of 25±10% (n=4) in cod muscle (BCR 422). A dry ashing procedure is given as a reference digestion, yielding complete recoveries of arsenic for both materials. The nitrite interference arising during measurement can be entirely overcome by using an amino sulfuric acid concentration of about 350 mmol/L in the solutions for measurement. Received: 30 April 1996/Revised: 12 July 1996/Accepted: 16 July 1996     

High performance liquid chromatographic determination of Picumast and two active metabolites in plasma using on-line sample preparation.

A method for determining Picumast, an antiallergic drug, in plasma by HPLC and column switching has been developed. The system consisted of two precolumns, an analytical column, three pumps, an autosampler and a fluorescence detector. The precolumns (17 x 4.6 mm i.d.) were packed with LiChroprep RPR (a moderately polar reversed phase) and the analytical column with Nucleosil ODS (RP 18, 5 microns). The columns were connected according to the alternating precolumn technique. The mobile phase consisted of 30% CH3CN/70% 0.05 M KH2PO4, pH 2.5, with a flow gradient. Detection wavelengths were 333 nm for excitation and 383 nm for emission. The retention times of Picumast, M1 and M2 were 12, 3.6 and 4.0 min, respectively. Total run time was 15 min. The limit of detection was 3 ng/mL for M1 and 1 ng/mL for M2 and Picumast using an injection volume of 150 microL. The recoveries vary between 89% and 97% with standard deviations between 2.4 and 3.3%.     

A method for trace element determination of marine periphyton communities on discs of float glass (without sample preparation) using total-reflection X-ray fluorescence spectrometry

A quick method for trace element determination of marine periphyton communities on soda float glass discs is presented. After addition of an internal standard, the community is measured by total-reflection X-ray fluorescence (TXRF) spectrometry. No sample preparation is required except a gentle wash with distilled water. The soda glass disc on which the periphyton community grows is used directly as the sample reflector in TXRF. The method was evaluated by the analysis of a certified reference material of plankton (CRM 414) and by comparison to a wet digestion method. Recovery rates for 13 and 130 μg-samples of CRM 414 are reasonable: between 0.6 and 1.4 for the elements K, Ca, Mn, Fe, Ni, Cu, Zn, As, Rb and Sr. Relative standard deviations for 130 μg-samples are 10% or less for most of these elements. In the comparison to wet digestion, natural periphyton samples were used and the two methods showed a good agreement.The different steps used in the quantification, such as accounting for the contribution from the glass to the TXRF spectrum, and the calculation of the sample mass from the spectrum, are described. It is shown that complicating factors, such as the required water wash and the influence of an inhomogeneous spatial distribution of the periphyton on the glass disc, do not adversely affect the quantification.     

Green analytical chemistry in sample preparation for determination of trace organic pollutants

The principles of green chemistry are applied to not only chemical engineering and synthesis, but also increasingly analytical chemistry. We describe environment-friendly analytical techniques applied to isolate and to enrich trace organic pollutants from solid and aqueous samples. Amounts of organic solvents used in analytical laboratories are reduced by applying solventless extraction, extraction using other types of solvent, assisted solvent extraction and miniaturized analytical systems.     

Miniaturized ternary deep eutectic solvent-based matrix solid-phase dispersion: A green sample preparation method for the determination of chlorophenols in river sediment

New ternary deep eutectic solvents were prepared and applied as efficient green dispersing solvents in miniaturized matrix solid-phase dispersion to extract chlorophenols from river sediments for the first time. High-performance liquid chromatography coupled with a photodiode array detector was used to analyze the target analytes. The significant factors affecting the extraction were optimized as follows: dispersant (100 mg), sample (100 mg), ternary eutectic solvents (150 μl), grinding for 1 min, 450 μl of acetonitrile as the elution solvent, and vortex mixing for 20 s. Under the optimal conditions, the method exhibited excellent linearity (correlation coefficient > 0.9980), low limits of detection between 1.039–2.478 μg/g, and extraction recoveries between 93.9% and 99.2%. Furthermore, the method demonstrated excellent precision in the intra- and inter-day analysis with a relative standard deviation below 6%. When compared to conventional extraction techniques, the miniaturized matrix solid-phase dispersion considerably reduced samples and solvent usag, offering important environmental benefits. The green profile of the method was assessed using the complementary green analytical procedure index tool confirming its eco-friendship. The technique was finally employed to evaluate sediment samples from three distinct locations along the Zuibaiji River, indicating its applicability for monitoring environmental samples.     

Certification for trace elements and methyl mercury mass fractions in IAEA-456 marine sediment sample

Accreditation and Quality Assurance - Marine sediment certified reference material (CRM), IAEA-456 was recently produced by the Environment Laboratories of the International Atomic Energy Agency...     

Sediment sample preparation for the determination of Pu and Am isotopes

Summary Sediment samples from the Romanian sector of the Danube River and the Black Sea coast were analyzed for Pu and Am. Three different ways of bringing the samples into solution were tested: acid attack, microwave digestion and alkaline fusion. A conventional anion-exchange resin was used to separate plutonium from other radionuclides and several variants were tried to improve the separation of americium. The preparation of thin sources for alpha-spectrometry was tested through electrodeposition and coprecipitation with Nd(III). Discussion and recommendations for the dissolution step, the americium separation and preparation of alpha sources are made.     

Evaluation of sample preparation methods for elastomer digestion for further halogens determination

In this work, three sample preparation methods were evaluated for further halogen determination in elastomers containing high concentrations of carbon black. Samples of nitrile-butadiene rubber, styrene-butadiene rubber, and ethylene-propylene-diene monomer elastomers were decomposed using oxygen flask combustion and microwave-induced combustion (MIC) for further Br and Cl determination by ion chromatography (IC), inductively coupled plasma optical emission spectrometry (ICP OES), and inductively coupled plasma mass spectrometry (ICP-MS). Extraction assisted by microwave radiation in closed vessels was also evaluated using water or alkaline solution. Digestion by MIC was carried out using 50 mmol l⁻¹ (NH₄)₂CO₃ as the absorbing solution. The effect of the reflux step was also evaluated. Accuracy was evaluated using certified reference materials with polymeric matrix composition and by comparison of results using neutron activation analysis. Agreement for Br and Cl was better than 95% by MIC using 5 min of reflux, and no statistical difference was found using IC, ICP OES, and ICP-MS for determination of both analytes. For MIC, the relative standard deviation (RSD) was lower than 5%. Using extraction in closed vessels, a high amount of residues was observed, and recoveries were lower than 45% for both analytes. For oxygen flask combustion, the agreement was similar using MIC but RSD was higher (20%). The residual carbon content, an important parameter used to evaluate the digestion efficiency, was always below 1% for MIC. Using MIC, it was possible to digest elastomers with high efficiency, resulting in a single solution suitable for halogen determination by different techniques.     

HPLC column-switching technique for sample preparation and fluorescence determination of propranolol in urine using fused-core columns in both dimensions

A new and fast high-performance liquid chromatography (HPLC) column-switching method using fused-core columns in both dimensions for sample preconcentration and determination of propranolol in human urine has been developed. On-line sample pretreatment and propranolol preconcentration were performed on an Ascentis Express RP-C-18 guard column (5?×?4.6 mm), particle size, 2.7 μm, with mobile phase acetonitrile/water (5:95, v/v) at a flow rate of 2.0 mL min^?1 and at a temperature of 50 °C. Valve switch from pretreatment column to analytical column was set at 4.0 min in a back-flush mode. Separation of propranolol from other endogenous urine compounds was achieved on the fused-core column Ascentis Express RP-Amide (100?×?4.6 mm), particle size, 2.7 μm, with mobile phase acetonitrile/water solution of 0.5 % triethylamine, pH adjusted to 4.5 by means of glacial acetic acid (25:75, v/v), at a flow rate of 1.0 mL min^?1 and at a temperature of 50 °C. Fluorescence excitation/emission detection wavelengths were set at 229/338 nm. A volume of 1,500 μL of filtered urine sample solution was injected directly into the column-switching HPLC system. The total analysis time including on-line sample pretreatment was less than 8 min. The experimentally determined limit of detection of the method was found to be 0.015 ng mL^?1.