5,7-二甲氧基香豆素合成方法的改进

以间苯三酚为原料,选甲醇进行甲基化反应制备3,5-二甲氧基苯酚,以丙炔酸乙酯经Pechmann环化反应制备了白柠檬素(5,7-二甲氧基香豆素)。考察了甲基化反应、环化反应的影响因素,结果表明n(间苯三酚)∶n(甲醇)=1∶15,干燥氯化氢为催化剂,75℃反应7h,甲基化收率为82%;n(丙炔酸乙酯)∶n(3,5-二甲氧基苯酚)∶n(无水氯化锌)=1∶3∶1,环化温度为100℃,N2保护下反应2h,环化反应收率为88%,两步反应总收率达73%。目标产物用红外、质谱、核磁分析手段进行了表征和分析。     

1,3,5-三甲氧基苯的绿色合成工艺

以间苯三酚(PG)为原料,碳酸二甲酯(DMC)为甲基化试剂,在K2CO3/(Bu)4NBr催化下合成了1,3,5-三甲氧基苯,其结构经1H NMR,13C NMR和HR-ESI-MS确证。最佳工艺条件为:PG 10 mmol,n(DMC)∶n[(Bu)4NBr]∶n(K2CO3)∶n(PG)=12∶0.15∶1.5∶1,于160℃反应24 h,收率76.0%。     

新型苯乙酰脒类化合物的合成及其感光性能

以氢化铝锂为还原剂,甲基叔丁基醚为溶剂,1,5-二氮杂双环[4.3.0]-5-壬烯(1)于55℃反应9 h制得1,5-二氮杂双环[4.3.0]壬烷(2),收率87.9%,纯度95.0%。2分别与溴代苯乙酮(3a),对甲氧基溴代苯乙酮(3b)和对溴基溴代苯乙酮(3c)进行消除反应合成了3个新型的苯乙酰基潜双环脒类化合物(4a~4c),其结构经1H NMR和LC-MS表征。采用正交实验对合成4a~4c的反应条件进行了优化。在最佳反应条件[以甲苯为溶剂,3a 25.2 mmol,n(3a)∶n(K2CO3)∶n(2)=1.0∶2.0∶1.4,于15℃反应24 h]下,1,5-二氮杂双环[4.3.0]-5-苯乙酰基壬烷(4a)收率89.0%,纯度87.9%。感光性能研究结果表明,1,5-二氮杂双环[4.3.0]-5-(4-甲氧基)苯乙酰基壬烷(4b)经紫外曝光400 mJ·cm-1,其引发性能最强,分解转化近45%;曝光2 000 mJ·cm-1,4b分解转化近90%。     

2,5-二甲氧基-4-[(1E)-2-(1H-苯并咪唑-2-基)乙烯基]苯甲醛的合成

以2-甲基苯并咪唑(1)和2,5-二甲氧基-1,4-对苯二甲醛(3)为原料,经缩合反应合成了新化合物——2,5-二甲氧基-4-[(1E) -2-( 1H-苯并咪唑-2-基)乙烯基]苯甲醛(4),其结构经1H NMR,IR和ESI-MS表征.较佳缩合反应条件为:1 11 mol,n(1)∶n(3)=1.1∶1.0,回流反应6h,收率75.2％.     

2-氨基-4-甲氧基氯代苯甲酸的合成研究

以2-氨基-4-甲氧基苯甲酸甲酯为原料,通过氯代反应,再分别通过酯水解反应得到化合物2-氨基-5-氯-4-甲氧基苯甲酸和2-氨基-3-氯-4-甲氧基苯甲酸。其中间体及产物结构经~1H NMR、~(13)C NMR和ESI-MS确证,并考察了最佳氯代反应条件。结果表明:物料配比为n(2-氨基-4-甲氧基苯甲酸甲酯)∶n(NCS)=1∶1. 2,反应溶剂为N,N-二甲基甲酰胺,反应时间为16 h,两种氯代产物2-氨基-5-氯-4-甲氧基苯甲酸甲酯和2-氨基-3-氯-4-甲氧基苯甲酸甲酯收率分别为47%和39%。     

4-(二苯氨基)苯甲醛的合成工艺改进

以Al Cl3为催化剂,三苯氨(1)和原甲酸三乙酯(2)为原料,合成了4-(二苯氨基)苯甲醛(3),其结构经1H NMR和FT-IR确证。合成3的较佳工艺条件为:1 40 mmol,n(1)∶n(2)∶n(Al Cl3)=1∶5∶8,苯为溶剂,于30℃反应4 h,收率91%。     

N-(2-吡啶甲基)取代的阿伐那非类似物的合成条件优化

以4-(3-氯-4-甲氧基苄基氨基)-2-[(2S)-2-羟甲基-1-吡咯烷基]-5-嘧啶羧酸乙酯为原料,合成了4-(3-氯-4-甲氧基苄基氨基)-2-[(2S)-2-羟甲基-1-吡咯烷基]-N-(2-吡啶甲基)-5-嘧啶甲酰胺,研究了此种阿伐那非类似物的合成条件优化,考察了投料比、反应温度、反应时间等因素对产率的影响.获得较高产率的反应条件为n(C6H8N2)∶n(C18H21ClN4O4)∶n(EDCI)∶n(HOBt)∶n(Et3N)=1.2∶1∶1.2∶1.2∶2,在搅拌下,60℃反应6h,经过后处理,柱层析纯化,得到类白色固体产物,产率为84.3%.所合成的产物经FT-IR、1 H NMR、13 C NMR、ESI-MS得到验证.     

4-(3,4-二甲氧基苯基)-5-硝基哌啶-2-酮的合成

以3-(3,4-二甲氧基苯基)-4-硝基丁酸甲酯(4),氨水和甲醛为原料,异丙醇溶液为溶剂,经曼尼希-酯胺解偶联反应合成了新化合物4-(3,4-二甲氧基苯基)-5-硝基哌啶-2-酮,其结构经1H NMR,13C NMR和EI-MS表征。在最佳反应条件{4 1.0 mmol,n(4)∶n(27%氨水)∶n(37%甲醛)=1.00∶1.30∶1.05,异丙醇[V(异丙醇)∶V(水)=5∶1]7.5 m L,于100℃反应12 h}下,收率74.1%。     

2α-甲基-2β-溴甲基青霉烷酸二苯甲酯的合成

以6,6-二氢青霉烷酸二苯甲酯-1-氧化物(Ⅰ)和2-巯基苯并噻唑为原料,通过热裂解开环反应和溴代环合反应,制备得到了β-内酰胺酶抑制剂他唑巴坦关键中间体2α-甲基-2β-溴甲基青霉烷酸二苯甲酯(Ⅲ)。考察了反应温度、反应时间、物料比、催化剂用量对目标产物的影响。结果表明,在n(Ⅱ)∶n(HBr)∶n(Na NO_2)=1∶3∶6,催化剂质量分数为4%,-5℃反应2. 5h的条件下,收率为85. 4%。产物结构经1HNMR、FTIR、MS等技术手段得到验证。     

对甲氧基肉桂酸甲酯的一锅式绿色合成

以茴香醛(1)和丙二酸二乙酯(2)为原料,L-脯氨酸/磷酸钠为催化剂,甲醇为溶剂,经Knoenenagel缩合反应一锅式合成了对甲氧基肉桂酸甲酯。较适宜的反应条件为:141.5 mmol,n(1)∶n(2)∶n(L-脯氨酸)=1.0∶1.3∶0.3,n(L-脯氨酸)∶n(磷酸钠)=6∶1,甲醇100 mL,回流反应6 h,收率达70.2%。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.