SIAmate-a compact and modular sequential injection analysis controller

A number of sequential injection analysis (SIA) measurement methods have been developed during the last years. Almost all have been used in laboratory conditions with good results, but very few have been implemented as on-line methods, applied to non-stop measurements, producing immediate results for process control. The transfer of an SIA system from laboratory to an industrial facility [J. Ruzicka, Anal. Chim. Acta 261 (1992) 3] requires a whole new range of details to be taken into account. Some SIA platform related topics will be discussed. There are numerous ways of building an SIA system that meets the needs of the industry. One alternative, SIAmate, is presented.     

顺序注射化学发光联用技术测定空气中的SO2

基于在酸性溶液中SO32-被Ce4 氧化成SO42-产生很强的化学发光的原理,将顺序注射(SI)进样和化学发光(CL)检测方法联用,以0.012%三乙醇胺作吸收液,成功地测定了空气中的SO2。其浓度与发光信号强度在6.40×10-9～1.28×10-5mol/L范围内呈线性关系。方法的检出限(3σ)为4.80×10-9mol/L,对3.20×10-7mol/L的SO32-溶液9次测定的相对标准偏差为2.9%,方法回收率为98.45～103.6%。分析频率为90样/h。     

Chemiluminescence determination of antibacterial drug trimethoprim by automated sequential injection technique with permanganate and hexametaphosphate as reagents

Antibacterial drug trimethoprim [2,4-diamino-5-(3,4,5-trimethoxybenzyl)-pyrimidine] (I) was determined in pharmaceutical formulations by using a lab-made PC-controlled SIA analyser linked to conventional HPLC fluorimetric detector equipped with a chemiluminescence module. The chemical principle is the oxidation of I by KMnO(4) in acid medium; the reaction is accompanied by the emission of chemiluminescence, which is enhanced in the presence of hexametaphosphate (HMP). The optimum sequence and the flow parameters and concentrations and volumes of reagents aspirated optimised by a computer-aided simplex method were, 100 mul of 5 mM HMP, 40 mul of a test solution of I, 2 mul of 0.5 M H(2)SO(4) and 20 mul of 1 mM KMnO(4); the luminescing zone was pushed into the detector at a flow rate of 49 mul s(-1). The calibration graph relating the intensity of luminescence to concentration of I was parabolic (r=0.9994) in the range 0.5-100 mug ml(-1) of I with rectilinear part (r=0.9999) in the range 20-100 mug ml(-1) of I; the limit of detection was 0.1 mug ml(-1) of I. The method was used for the assay of Triprim(R) tablets (with nominal content 100 or 200 mg of I) for the active substance as well as for content uniformity tests; the R.S.D. values did not exceed 1% (n=5). The SIA results did not show statistical difference from those obtained by pharmacopoeial acidimetric titration in non-aqueous medium; the excipients such as microcrystalline cellulose, maze starch, povidone, talc, magnesium stearate and gelatin did not interfere.     

顺序注射化学发光联用技术测定食品中的碘

基于酸性溶液中HCHO存在下,KMnO4可氧化I-产生很强的化学发光的原理,建立了一个简单快速测定微量碘的顺序注射化学发光分析方法。I-在3.0×10-8~8.0×10-6mol/L范围内与发光强度呈良好线性关系。对2.0×10-6mol/L I-11次重复测定的相对标准偏差(RSD)为2.6%,方法的检出限(3σ)1.3×10-8mol/L,测定了4种食品中的碘量,回收率为92.8%~107.7%。分析频率为70 h。     

On-line separation, simultaneous dilution and spectrophotometric determination of zinc in fertilisers with a sequential injection system and xylenol orange as complexing agent

A dialyser unit, equipped with a passive neutral membrane, was incorporated into the conduits of a sequential injection (SI) system for the on-line removal of suspended solids and simultaneous dilution of the analyte before reaction and detection of the analyte. The system was applied to the determination of zinc(II) in fertilisers. The fully automated system is able to analyse zinc at a sampling frequency of ten samples per hour at a %R.S.D. of better than 0.55. The calibration graph was linear between 10 and 50 mg l⁻¹. The detection limit was found to be 4.75 mg l⁻¹. The results obtained with the proposed SI analyser compared favourably with the standard manual flame atomic absorption spectrometric method.     

Exploiting sequential injection analysis with lab-at-valve (LAV) approach for on-line liquid-liquid micro-extraction spectrophotometry

Sequential injection analysis (SIA) with lab-at-valve (LAV) approach for on-line liquid-liquid micro-extraction has been exploited. Sample, reagent and organic solvent were sequentially aspirated into a coil attached to a central port of a conventional multiposition selection valve, where the extraction process was performed. The aqueous and organic phases were separated in a conical separating chamber LAV unit attached at one port of the valve. The organic phase containing extracted product was then monitored spectrophotometrically. The system offers a novel alternative on-line automated extraction in a micro-scale and has been successfully demonstrated for the assays of diphenhydramine hydrochloride (DPHH) in pharmaceutical preparations and anionic surfactant in water samples.     

At-line determination of formaldehyde in bioprocesses by sequential injection analysis

A sequential injection analysis (SIA) method for the at-line determination of formaldehyde in a cultivation process of Pichia pastoris is presented. A genetically modified yeast strain was used for cultivation processes wherein methanol feed induced the production of the recombinant protein 1-3del I-TAC. Recurring measurements of culture medium, its blank and including standard addition were performed with Nash reagent using an automated syringe device and photometric detection. The apparatus was coupled via a laboratory-made flow-through adapter to a continuous filtered and cell-medium flow from the bioreactor. At-line monitoring of formaldehyde was performed at two cultivations, each of 250 h during fed-batch phases with glycerol and methanol as carbon sources. High reliability, robustness and reproducibility of the method, the software and the instrumentation as well as the high selectivity of the reaction were demonstrated.     

Quasi-simultaneous determination of antioxidative activities against superoxide anion and nitric oxide by a combination of sequential injection analysis and flow injection analysis with chemiluminescence detection

A method that combines sequential injection analysis (SIA), flow injection analysis and chemiluminescence (CL) detection was developed for the quasi-simultaneous determination of antioxidative activities against superoxide anion and nitric oxide (NO). The antioxidative activity was expressed as the decrease in luminol CL intensity caused by the quenching of or NO by an antioxidant. The SIA system consisted of two syringe pumps, two selection valves, two holding coils, an HPLC pump to deliver luminol solution, and a CL detector. Operation of the syringe pumps and multiport valves was controlled automatically using a personal computer with appropriate software. A hypoxanthine (HX)-xanthine oxidase (XOD) system was used for the generation of , and (±)-(E)-4-methyl-2-[(E)-hydroxyimino]-5-nitro-6-methoxy-3-hexenamide (NOR1) was employed as NO donor agent. The repeatability of the method was evaluated with 35.2 μg ml⁻¹ L-ascorbic acid, and the relative standard deviations (RSD) of the antioxidative activities were less than 3.8%. The quasi-simultaneous determination of the antioxidative activities in one sample was completed within 2.0 min. The antioxidative activities of some antioxidants and commercially available supplements containing certain antioxidants were successfully determined using this system. The proposed system is rapid and reproducible, and thus may be useful for the screening of functional foods, supplements and pharmaceutical formulations that exhibit antioxidative activity. Figure The system that utilizes a combination of SIA and FIA with CL for the quasi-simultaneous determination of antioxidative activity against a NO and b . SP1, 2: syringe pump, HC1, 2: holding coil, MV1, 2: multi-port valve, P: pump, D: chemiluminescence detector, I: integrator, M1, 2: mixing tee, NOR1: (±)-(E)-4-methyl-2-[(E)- hydroxyimino]-5-nitro-6-methoxy-3-hexenamide, HX: hypoxanthine, XOD: xanthine oxidase.     

Enzymatic chemiluminescent assay of glucose by sequential-injection analysis with soluble enzyme and on-line sample dilution

This work reports a sequential-injection analysis (SIA) method for the enzymatic assay of glucose with soluble glucose oxidase (GOD) and on-line sample dilution with chemiluminescence (CL) detection. A zone of sample was aspirated in the holding coil of the SIA manifold and, if necessary, was diluted on-line by means of an auxiliary dilution conduit. Then, a zone of GOD was aspirated adjacent to the sample zone and a stopped-flow period was applied to allow the enzymatic reaction to proceed with production of hydrogen peroxide. Then, zones of a catalyst (Co(II) solution) and alkaline luminol were aspirated into the holding coil. Finally, the flow was reversed and the stacked zones were sent to a flow-cell located in front of a photomultiplier tube (PMT) that monitored the CL intensity. The linear dynamic range was 1 × 10⁻⁵-1 × 10⁻³ mol L⁻¹ glucose, the coefficient of variation at 8 × 10⁻⁵ mol L⁻¹ of glucose was s_r = 3.1% (n = 8), the limit of detection at the 3σ level was c_L = 1 × 10⁻⁶ mol L⁻¹ and the sampling frequency was 28 h⁻¹. With on-line dilution by a factor of 1/200, the linear range could be extended up to 0.2 mol L⁻¹ glucose. The advantages of the proposed method are the simple manifold and instrumentation used, the scope for automated on-line dilution, the low consumption of sample and reagents and the elimination of enzyme immobilisation procedures. The method was applied to the analysis of commercial drinks and honey with percent relative errors in glucose determination in the range 100 ± 6.1%.     

On-line simultaneous monitoring of glucose and acetate with FIA during high cell density fermentation of recombinant E. coli

A two-channel flow injection analysis (FIA) system was developed for the simultaneous on-line monitoring of acetate and glucose during high cell density fed-batch fermentations of recombinant Escherichia coli. Acetate measurement was performed with a modified and optimised version of an existing method, based on acetate diffusion through a gas-diffusion chamber into a stream containing an acid-base indicator. The subsequent decrease in the absorbance was detected with an incorporated photometer. After method optimisation, it was possible to achieve linearity until 10 g/kg with no dilution step and with a detection level of 0.05 g/kg. Although some interferences were found, the performance of the method proved to be sufficiently reliable for on-line control purposes Commercially packed glucose oxidase (GOD) was used for the amperometric measurement of glucose. The method was linear up to 5 g/kg and it was possible to detect concentrations lower than 0.06 g/kg. For these measurements, no significant interferences were detected when the results were compared with other reference methods. The application of a simultaneous parallel configuration of the methods to a high cell density fed-batch E. coli fermentation was tested and reliable results were obtained within a 3 min delay. This information was made available to a supervisory computer running a developed LabVIEW™ programme via an Ethernet network, allowing the immediate implementation of control actions, improving the process performance.     

Pre-evaluation of metal ions as a catalyst on chemiluminometric sequential injection analysis with luminol-H2O2 system

Catalytic effect of metal ions on luminol chemiluminescence (CL) was investigated by sequential injection analysis (SIA). The SIA system was set up with two solenoid micropumps, an eight-port selection valve, and a photosensor module with a fountain-type chemiluminescence cell. The SIA system was controlled and the CL signals were collected by a LabVIEW program. Aqueous solutions of luminol, H₂O₂, and a sample solution containing metal ion were sequentially aspirated to the holding coil, and the zones were immediately propelled to the detection cell. After optimizing the parameters using 1 × 10⁻⁵ M Fe³⁺ solution, catalytic effect of some metal species was compared. Among 16 metal species examined, relatively strong CL responses were obtained with Fe³⁺, Fe²⁺, VO²⁺, VO₃⁻, MnO₄⁻, Co²⁺, and Cu²⁺. The limits of detection by the present SIA system were comparable to FIA systems. Permanganate ion showed the highest CL sensitivity among the metal species examined; the calibration graph for MnO₄⁻ was linear at the concentration level of 10⁻⁸ M and the limit of detection for MnO₄⁻ was 4.0 × 10⁻¹⁰ M (S/N = 3).     

Spectrofluorimetric determination of aluminum in drinking waters by sequential injection analysis

A selective procedure for the determination of Al³⁺ in drinking and natural waters is proposed. The analytical procedure is based both on the complex formation between Al³⁺ and 8-hydroxyquinoline-5-sulfonic acid (HQS) and on a fluorimetric detection of the complex. The reaction was carried out in presence of thioglycolic acid as a masking agent. This procedure has been adapted to a sequential injection analysis (SIA) system. Operative conditions both for batch and SIA procedures were investigated including reagent concentration, volumes, pH and wavelengths used for the fluorimetric detection. Batch procedure allows determination of Al³⁺ at ppb level (LOQ: 2.8 μg l⁻¹) within a working range of 2.2-300 μg l⁻¹. The SIA procedure was successfully employed for the determination of Al³⁺ in several commercial drinking and tap waters.     

Determination of aluminum by electrothermal atomic absorption spectroscopy in lubricating oils emulsified in a sequential injection analysis system

The sequential injection (SIA) technique was applied for the on-line preparation of an “oil in water” microemulsion and for the determination of aluminum in new and used lubricating oils by electrothermal atomic absorption spectrometry (ET AAS) with Zeeman-effect background correction. Respectively, 1.0, 0.5 and 1.0 ml of surfactants mixture, sample and co-surfactant (sec-butanol) solutions were sequentially aspirated to a holding coil. The sonication and repetitive change of the flowing direction improved the stability of the different emulsion types (oil in water, water in oil and microemulsion). The emulsified zone was pumped to fill the sampling arm of the spectrometer with a sub-sample of 200 μl. Then, 10 μl of this sample solution were introduced by means of air displacement in the graphite tube atomizer. This sequence was timed to synchronize with the previous introduction of 15 μg of Mg(NO₃)₂ (in a 10 μl) by the spectrometer autosampler. The entire SIA system was controlled by a computer, independent of the spectrometer. The furnace program was carried out by employing a heating cycle in four steps: drying (two steps at 110 and 130 °C), pyrolisis (at 1500 °C), atomization (at 2400 °C) and cleaning (at 2400 °C). The calibration graph was linear from 7.7 to 120 μg Al l⁻¹. The characteristic mass (mo) was 33.2 pg/0.0044 s and the detection limit was 2.3 μg Al l⁻¹. The relative standard (RSD) of the method, evaluated by replicate analyses of different lubricating oil samples varied in all cases between 1.5 and 1.7%, and the recovery values found in the analysis of spiked samples ranged from 97.2 to 100.4%. The agreement between the observed and reference values obtained from two NIST Standard Certified Materials was good. The method was simple and satisfactory for determining aluminum in new and used lubricating oils.     

顺序注射催化动力学光度法测定织物和室内空气中痕量甲醛

在磷酸介质中 ,甲醛可以催化溴酸钾氧化　花青的反应使其退色 ,据此建立了顺序注射催化动力学光度法测定织物和室内空气中痕量甲醛的新方法。方法的线性范围 0 .5～ 7.0 μg mL ,检出限 0 .1 μg mL。用于树脂整理特殊织物和室内空气中痕量甲醛的测定 ,回收率在 97.0 %～ 1 0 5 .0 %之间。     

Determination of carbonate and hydrogencarbonate by titration using sequential injection analysis

A fully automated spectrophotometric sequential injection titration system has been developed for the determination of carbonate and hydrogencarbonate in water samples. The sample is titrated against hydrochloric acid using phenolphthalein and methyl orange as indicators; the absorbance is measured at 430 nm. A logarithmic relationship is obtained between the peak width and the absorbance. The logarithmic range for carbonate is 0.0008-0.01 M, and for hydrogencarbonate is 0.001-0.01 M. Reproducibility is good (<2% for carbonate and <1.5% for hydrogencarbonate) and the results obtained agree well with those obtained using a potentiometric titration. The sample throughput is 12 samples h⁻¹.     

Composite poly(dimethylsiloxane)/glass microfluidic system with an immobilized enzymatic particle-bed reactor and sequential sample injection for chemiluminescence determinations

A three-layer poly(dimethylsiloxane) (PDMS)/glass microfluidic system for performing on-chip solid-phase enzymatic reaction and chemiluminescence (CL) reaction was used for the determination of glucose as a model analyte. A novel method for the immobilization of controlled-pore-glass based reactive particles on PDMS microreactor beds was developed, producing an on-chip solid-phase reactor that featured large reactive surface and low flow impedance. Efficient mixing of reagent/sample/carrier streams was achieved by incorporating chaotic mixer structures in the microfluidic channels. A conventional sequential injection (SI) system was adapted for direct coupling with the microfluidic system, and combined with hydrostatic delivery of reagents to achieve efficient and reproducible sample introduction at 10 μl levels. A detection limit of 10 μM glucose (3σ), and a precision of 3.1% RSD (n=7, 0.2 mM glucose) were obtained using the SI-microfluidic-CL system integrated with a glucose oxidase (GOD) reactor. Carryover was <5% at a throughput of 20 samples/h.     

Chemiluminescence sequential injection immunoassay for vitellogenin using magnetic microbeads

A rapid and sensitive immunoassay for the determination of carp vitellogenin (Vg) is described. The method involves a sequential injection analysis (SIA) system equipped with a chemiluminescence detector and a samarium-cobalt magnet. An anti-Vg monoclonal antibody, immobilized on magnetic beads, was used as a solid support for the immunoassay. The introduction, trapping and release of the magnetic beads in the flow cell were controlled by a samarium-cobalt magnet and the flow of the carrier solution. The immunoassay was based on a sandwich immunoreaction of anti-Vg monoclonal antibody (primary antibody) on the magnetic beads, Vg, and the anti-Vg antibody labeled with horseradish peroxidase (HRP) (secondary antibody), and was based on a subsequent chemiluminescence reaction of HRP with hydrogen peroxide and p-iodophenol, in a luminol solution. The magnetic beads to which the primary antibody was immobilized were prepared by coupling the primary antibody with the magnetic beads after an agarose-layer on the surface of the magnetic beads was epoxidized. The primary antibody-immobilized magnetic beads were introduced, and trapped in the flow cell equipped with the samarium-cobalt magnet, a Vg sample solution, an HRP-labeled secondary antibody solution and the luminol solution were sequentially introduced into the flow cell based on an SIA programmed sequence. Chemiluminescence emission was monitored by means of a photomultiplier located at the upper side of the flow cell. The optimal incubation times both for the first and second immunoreactions were determined to be 20 min. A concave calibration curve was obtained between Vg concentration and chemiluminescence intensity when various concentrations of standard Vg samples (2–100 ng mL⁻¹) were applied to the SIA system under optimal conditions. In spite of a narrow working range, the lower detection limit of the immunoassay was about 2 ng mL⁻¹.     

A thionine-based reversible redox sensor in a sequential injection system

According to the current demands of Green Analytical Chemistry and regarding the need for lower reagent consumption with improved analytical performance, an automatic methodology with a flow-through optosensor incorporating solid-phase spectrophotometric detection was developed. The sensor used in this work was based on the redox state of thionine whose oxidized form is blue and reduced form is colorless with monitoring carried out at 621 nm. This redox indicator was immobilized on gel beads and subsequently packed into a flow-through cell. It was then assembled into a sequential injection system and was shown to be an excellent alternative to monitor enzymatic redox reactions automatically as the redox catalysis is performed by glucose dehydrogenase. This enzyme is a representative dehydrogenase enzyme and uses NAD⁺ as cofactor, promoting the oxidation of glucose to glucono-lactone and reduction of NAD⁺ to NADH. The produced NADH promotes color depletion on the surface of the sensor. The calibration graph for glucose was linear between 5.74 × 10⁻⁴ and 2.00 × 10⁻³ mol L⁻¹ and detection limit was 1.72 × 10⁻⁴ mol L⁻¹. Glucose concentration in different samples including sera, salines, perfusion solutions, powder for preparing oral solutions and solutions for hemodialysis was determined. The method proved to be reproducible with a RSD < 5% for glucose determinations.     

A review on sequential injection methods for water analysis

The development of fast, automatic and less expensive methods of analysis has always been the main aim of flow methodologies. The search for new procedures that still maintain the reliability and accuracy of the reference procedures is an ever growing challenge. New requirements are continually added to analytical methodologies, such as lower consumption of samples and reagents, miniaturisation and portability of the equipment, computer interfaces for full decision systems and so on. Therefore, the development of flow methodologies meeting the extra requirements of water analysis is a challenging work.Sequential injection analysis (SIA) presents a set of characteristics that make it highly suitable for water analysis. With sequential injection analysis, most routine determinations in waters can be performed more quickly with much lower reagent consumption when compared to reference procedures. Additionally, SIA can be a valuable tool for analyte speciation and multiparametric analysis. This paper critically reviews the overall work in this area.     

High-sensitivity methods for sequential injection determination of the main constituents of alloys

A sequential injection system with spectrophotometric detection was proposed for the determination of copper, zinc and lead in brass. In view of the high analyte concentrations and the sensitivity of the involved catalytic methods, optimization of the flow system was carried out aiming mild reaction conditions. Copper and lead determinations were based on the catalytic effects of Cu²⁺ and Pb²⁺ on the oxidation rates of resorcinol and pyrogallol red by H₂O₂, respectively, and zinc determination involved precipitate formation after oxidation of 1-nafthylethylenediamine by K₃Fe(CN)₆. The analytical procedures were designed with some common parameters such as pH=9.0 (borate system), λ=530 nm, and H₂O₂ as oxidizing agent; system geometry was maintained.The proposed system is rugged, and base line drift is not observed during 4 h operation periods. Twenty samples are run per hour (60 determinations) and reagent consumption is minimal, thus avoiding drawbacks related to waste management. Precise results (R.S.D.<1.0%; n=7) are obtained and a detection limit of 1% (w/w) was estimated for the three analytes. Results were in agreement with flame atomic absorption spectrometry.