Amide and Acyl‐Hydrazine Functionalized Calix[4]arenes as Carriers for Hydrogen Phosphate Selective Electrodes

Anion‐selective solvent polymeric membrane based on hydrogen bond‐forming, neutral ionophores with amide or acyl‐hydrazine groups are described. The use of the two calix[4]arenes results in anion‐selective electrodes with a selectivity for phosphate. The electrodes of the optimum characteristic have the composition of 1 wt% ionophore, 66 wt% o‐NPOE, 33 wt% poly (vinyl chloride) (PVC) and TDMACl (15 or 30 mol% relative to the ionophore 1 and 2 , respectively). The optimized membrane electrodes show Nernstian responses towards monohydrogen phosphate (?29.1 and ?29.3 mV/decade) based on ionophore 1 and 2 , respectively, in a wide concentration range (1.0×10^?5 to 1.0×10^?2 or 1.0×10^?5 to 1.0×10^?1 M). The selectivity coefficients are determined with the fixed interference method and the activity ratio method. The electrodes display an anti‐Hofmeister series selectivity pattern and highly selective for HPO₄^2? over Cl^?, Br^?, CH₃COO^?, NO₃^? and SO₄^2?. The lifetime of the electrodes is at least 1 month and their response time is found to be 25 s. The proposed sensors could be put to analytical use both by direct potentiometry as well as potentiometric titration.     

Novel Cesium‐Selective Electrodes Based on Lipophilic 1,3‐Bisbridged Cofacial‐calix[6]crowns

Five bisbridged calix[6]crowns have been investigated as Cs⁺ ionophore in PVC membrane electrodes. As ionophores, three 1,3‐bisbridged calix[6]crown‐4‐ethers( I–III ), 1,3‐bisbridged calix[6]crown‐5‐ether( IV ), and 1,3‐bisbridged calix[6]crown‐6‐ether( V ) have been evaluated. The membranes all give good Nernstian response in the concentration range from 1×10^?7 to 1×10^?1 M of cesium ion. The best detection limits (?log aequation/tex2gif-inf-1.gif=7.08–7.36) are obtained for electrode membranes containing 1,3‐bisbridged cofacial‐calix[6]crown‐4‐ethers( I‐III ), and the values are the lowest compared with those reported previously. The highest selectivity coefficients [ 3.74(Cs/K), 2.63(Cs/Rb)] are obtained for the membrane of 1,3‐bisbridged calix[6]crown‐4‐ether( II ), and these values are also the highest compared with previous reports for Cs⁺‐ISEs. The highest selectivity towards cesium ion is attributed to the geometrically cofacial positions of two crown‐ethers in calix[6]crowns in order to provide the complex of cesium ion and eight oxygens of cofacial crowns.     

Mono Halogen Substituted Calix[4]pyrroles: Fine-tuning the Anion Binding Properties of Calix[4]pyrrole

Abstract

Single halogen atom (i. e. I, Br, Cl and F) substituted calix[4]pyrroles, compounds 2, 3, 4 and 5, were synthesized. Studies of these systems reveal that replacement of a single β-pyrrolic hydrogen atom can increase the anion binding ability of calix[4]pyrroles for a variety of anions (e. g. Cl^?, Br^?, H₂PO₄ ^? and HSO^? ₄) relative to normal non-halogen substituted calix[4]pyrrole 1. In the case of chloride anion, the expected relative affinity sequence of 5 > 4 > 3 > 2 was observed. This was not found to be true for Br^?, H²PO^? ₄, and HSO^? ₄. Here, the chlorine substituted calix[4]pyrrole 4 was found to display a slightly higher affinity in the case of each anion than the fluorine-bearing derivative 5. This was rationalized in terms of intermolecular NH … F hydrogen bonding interactions being present in CD₂Cl₂ solutions of 5. Support for this latter conclusion came from concentration and temperature-dependent NMR spectroscopic studies.

A matched set of mono halogen substituted calix[4]pyrroles was used to study in detail, the extent to which halogen substituents may be used to fine-tune the anion binding properties of calix[4]pyrroles.     

A Highly Selective and Sensitive Barium(II)‐Selective PVC Membrane Based on Dimethyl 1‐Acetyl‐8‐oxo‐2,8‐dihydro‐ 1H‐pyra‐zolo[5,1‐a]isoindole‐2,3‐dicarboxylate

A poly(vinyl chloride)‐based membrane of dimethyl 1‐acetyl‐8‐oxo‐2,8‐dihydro‐1H‐pyra‐zolo[5,1‐a]isoindole‐2,3‐dicarboxylate as a neutral carrier with sodium tetraphenylborate (NaTPB) as an anion excluder and 2‐nitrophenyl octyl ether (NPOE) as plasticizer was prepared and investigated as a Ba(II)‐selective electrode. The electrode exhibits a Nernstian slope of 29.7±0.4 mV per decade over a wide concentration range (1.0×10^?6 to 1.0×10^?1 M) with a detection limit of 7.6×10^?7 M between pH 3.0 and 11.0. The response time of the sensor is about 10 s and it can be used over a period of 2 months without any divergence in potential. The proposed membrane sensor revealed good selectivity for Ba(II) over a wide variety of other metal ions. It was successfully used in direct determination of barium ions in industrial wastewater samples.     

Homooxacalix[3]arene Derivatives as Ionophores for Serotonin‐Selective Membrane Electrodes

Homooxacalix[3]arene derivatives are effective ionophores for constructing serotonin‐selective membrane electrodes. An electrode based on one of the derivatives, tris(methoxyphenylpropyloxy)hexahomooxacalix[3]arene‐triethyl ether, with potassium tetrakis(p‐chlorophenyl)borate (20 mol% relative to the ionophore) as an ionic additive and bis(2‐ethylhexyl) sebacate as a solvent mediator in a poly(vinyl chloride) membrane matrix, displayed much better selectivity for serotonin than for various organic ammonium ions and inorganic cations. The electrode exhibited a near‐Nernstian response to serotonin in the concentration range of 2×10^?4 to 1×10^?2 M with a slope of 56.4 mV per concentration decade in physiological saline containing 150 mM NaCl and 10 mM Na₂HPO₄/NaH₂PO₄ (pH 7.4). The limit of the detection was 8×10^?5 M. The selectivity pattern of this electrode was quite different from that of an electrode using calix[6]arene‐hexaacetic acid hexaethyl ester, a well‐known ionophore for primary organic ammonium ions, which did not induce an enhanced response to serotonin. The developed electrode was used for the active loading of serotonin in liposomes induced by transmembrane pH gradients.     

Study by fluorescence of calix[4]arenes bearing heterocycles with anions: highly selective detection of iodide

The present work describes a study of complexation efficiency of calix[4]arenes bearing benzoimidazolyl, benzothiazolyl, and benzoxazolyl heterocycles (5–7) towards several anions. The binding ability of calixarene derivatives 5–7 towards selected anions of different molecular geometries such as: F^?, HSO₄ ^?, I^?, N₃ ^?, NO₃ ^?, NO₂ ^?, SCN^?, ClO₄ ^?, Br^?, CN^?, Cl^?, CH₃COO^? CF₃SO₃ ^? in methanol, has been investigated by fluorescence spectroscopic techniques, all anions were used as tetrabutylammonium salts to avoid possible complexation of cationic species by the derivative calix[4]arenes. Fluorescent chemosensor ability of these three calixarene derivatives was highly selective for iodide in contrast with other anions studied. The best chemosensor found, corresponds to compound 7, with an association constant of 2.01 × 10⁴ mol^?1 L and a detection limits of 0.22 ppm for iodide.     

[Cu(L)](NO3)2 (L=4,7‐Bis(3‐aminopropyl)‐1‐thia‐4,7‐diazacyclononane) as a Suitable Ionophore for Construction of Thiocyanate‐Selective Electrodes and Their Use in Determination of Urinary and Salivary Thiocyanate Concentration

The construction, performance characteristics, and application of polymeric membrane (PME) and coated graphite (CGE) thiocyanate‐selective electrodes are reported. The electrodes were prepared by incorporating the complex [Cu(L)](NO₃)₂ (L=4,7‐bis(3‐aminopropyl)‐1‐thia‐4,7‐diazacyclononane) into a plasiticized poly(vinyl chloride) membrane. The influence of membrane composition, pH of test solution, and foreign ions were investigated. The electrodes reveal Nernstian behavior over a wide SCN^? ion concentration range (1.0×10^?6–1.0×10^?1 M for PME and 5.0×10^?7–1.0×10^?2 M for CGE) and show fast dynamic response times of 15 s and lower. The proposed sensors show high selectivity towards thiocyanate over several common organic and inorganic anions. They were successfully applied to the direct determination of thiocyanate in urine and saliva of smokers and nonsmokers, and as an indicator electrode in titration of Ag⁺ ions with thiocyanate.     

Highly Selective Perchlorate Membrane Electrode Based on Cobalt(III) Schiff Base as a Neutral Carrier

A highly selective poly(vinyl chloride) (PVC) membrane electrode based on Co(III)-Schiff base [Co(5-NO2- Salen)(PBu3)]ClO4•H2O (where 5-NO2-SalenH＝bis(5-nitrosalycilaldehyde)ethylenediamine) as a new carrier for construction of perchlorate-selective electrode by incorporating the membrane ingredients on the surface of a graphite electrodes has been reported. The proposed electrode possesses a very wide Nernestian potential linear range to perchlorate from 1.0×10－6 to 5.0×10－1 mol•L－1 with a slope of (59.4±0.9) mV per decade of perchlorate concentration with a low detection limit of 5.0×10－7 mol•L－1 and good perchlorate selectivity over the wide variety of other anions. The developed electrode has an especially fast response (＜5 s) and a wide pH independent range (3.0—12.0) in comparison with recent reported electrodes and can be used for at least 2 months without any considerable divergence in their potential response. This electrode was used for the determination of perchlorate in river water, drinking water, sludgy water and human urine with satisfactory results without complicated and time consuming pretreatment.     

Highly Selective Thiocyanate Electrode Based on Bis‐bebzion Schiff Base Binuclear Copper(II) Complex as Neutral Carrier

Abstract

A highly selective polyvinyl chloride (PVC) membrane electrode, based on N,N′‐(aminoethyl)ethylenediamide bis(2‐benzoideneimine) binuclear copper(II) complex [Cu(II)‐AEBB] as neutral carrier, was prepared for thiocyanate (SCN^?) determination, which displays an anti‐Hofmeister selectivity sequence for a series of anions in the following order: SCN^?>ClO₄ ^?>Sal^? > I^?>NO₃ ^?>Br^?> Cl^?>NO₂ ^?>SO₃ ^2?>F^?>H₂PO₄ ^?>SO₄ ^2?. The electrode exhibited near‐Nernst response for SCN^? with a slope of –59.0 mV/decade over a wide concentration range (8.5×10^?7～6.8×10^?1 mol/L) with a detection limit of –5.0×10^?7 mol/L in pH 5.0 phosphate buffer solution at 25°C. Alternating current (AC) impedance and equivalent circuits were used to investigate the thiocyanate response mechanism of the membrane doped with [Cu(II)‐AEBB].     

Salicylate-Selective PVC Membrane Electrodes Based on Tribenzyltin(IV) Phenolates as Neutral Carriers

ABSTRACT

A series of tribenzyltin(IV) phenolates were synthesized and used as anion ionophores for PVC membrane electrodes; these novel electrodes exhibit a linear response towards salicylate and an anti-Hofmeister selectivity pattern with high specificity for salicylate over many common anions. The results show that the behavior of the electrodes is considerably influenced by the structures of the carriers and the experimental conditions. Electrodes based on tribenzyltin(IV) p-nitrophenolate possess the best potentiometnc response characteristics and show a linear log[Sal^?] vs. EMF response over the concentration range 0.1–3.98×10^?6 mol.L^?1 in phosphate buffer solutions of pH 5.38 with a detection limit of 2.51×10^?6 mol.L^?1 and a slope of -57.05 mV per decade. The response mechanism was also investigated by use of a.c. impedance and anion transport across liquid membranes. The electrodes were applied to the determination of salicylate in urine samples with satisfactory results.     

A Novel Sulfate Polymeric Membrane Sensor Based on a New Bis‐Pyrylium Derivative

A novel ion‐selective polymeric membrane sensor based on pyrylium‐4,4‐(1,4‐phenylen) bis[2,6‐bis(2‐naphthyl)]‐bis[tetrafluoroborate] (PBGNB) as an excellent sensing material is successfully developed. The electrode possesses the advantages of a very low detection limit (5.0×10^?8 M), a wide working concentration range (1.0×10^?8?1.0×10^?1 M) and specially, a high sulfate selectivity over most common organic and inorganic anions. The sensor displays Nernstian behavior (slope of 29.5±0.5 mV per decade) in a wide pH range (3.0–8.5). It shows a short response time in the whole concentration range (ca. 10 s). The electrode was used as an indicator electrode in the potentiometric titration of sulfate ions with barium ions. The proposed sensor was successfully applied to the direct determination of salbutamol sulfate and paromomycin sulfate.     

A novel colorimetric and fluorometric anion sensor based on BODIPY-calix[4]pyrrole conjugate

A novel fluorescent anion sensor 1 based on boradiazaindacenes (BODIPY) derivative was synthesized and its absorption and fluorescence properties were investigated in various solvents. 1 exhibited a red shift of absorption spectrum and fluorescence quenching in varying degree in the presence of F^?, AcO^?, H₂PO₄ ^? and Cl^? due to multiple hydrogen bonding interactions between these anions and calix[4]pyrrole receptor. As an anion sensor in the visible region, 1 displayed the similar selectivity and sensitivity toward anions compared to the parent calix[4]pyrrole. However, 1 can be used as an effective dual responsive optical sensor for F^? via chromogenical and fluorogenical signals.     

Salicylate Ion‐Selective Electrode Based on a Calix[4]arene as Ionophore

A salicylate‐selective electrode based on calix[4]arene derivative was developed and its response characteristics were investigated. The optimum membrane composition was 1 % ionophore, 30 % PVC, 69 % DOS. The electrode exhibited a Nernstian slope of 58.8±0.5 mV/pSal in the range of 1.0×10^?5–1.0×10^?1 M with a detection limit of 4.3×10^?6 M at pH 4.0, 20±1 °C. The potentiometric response of the electrode in the presence of different anions was investigated by the separate solution method. The lifetime was found at least 4 months, and its response time was 5–10 s. It was successfully used for the potentiometric determination of salicylate in pharmaceutical preparations.     

Iodide‐Selective Electrodes Based on Bis[N(2‐methyl‐phenyl) 4‐Nitro‐thiobenzamidato]mercury(II) and Bis[N‐phenyl 3,5‐Dinitro‐thiobenzamidato]mercury(II) Carriers

Highly selective poly(vinyl chloride) (PVC) membrane electrodes based on recently synthesized mercury complexes including Hg(Nmpntb)₂ and Hg(Npdntb)₂ as new carriers for iodide‐selective electrodes by incorporating the membrane ingredients on the surface of graphite electrodes are reported. The effect of various parameters including the membrane composition, pH and possible interfering anions were investigated on the response properties of the electrodes. Both sensors exhibited Nernstian responses toward iodide over a wide concentration range of 7×10^?7 to 0.1 M and 1×10^?6 to 0.1 M, with slopes of 59.6±0.8 and 58.9±0.9 mV per decade of iodide concentration and detection limit of 3×10^?7 M and 7×10^?7 for Hg(Npdntb)₂ and Hg(Nmpntb)₂, respectively, over a wide pH range of 3–11. The sensors have response times of ≤5 s and can be used for at least 2 months without any considerable divergence in their potential response. The proposed electrodes show good ability to discriminate iodide over several inorganic and organic anions. The electrodes were successfully applied to direct determination of iodide in synthetic mixture, waste water and drinking water and as indicator electrodes in precipitation titrations.     

Silver(I)‐Selective PVC Membrane Potentiometric Sensor Based on a Recently Synthesized Calix[4]arene

A new PVC membrane potentiometric sensor for Ag(I) ion based on a recently synthesized calix[4]arene compound of 5,11,17,23‐tetra‐tert‐butyl‐25,27‐dihydroxy‐calix[4]arene‐thiacrown‐4 is developed. The electrode exhibits a Nernstian response for Ag(I) ions over a wide concentration range (1.0×10^?2?1.0×10^?6 M) with a slope of 53.8±1.6 mV per decade. It has a relatively fast response time (5–10 s) and can be used for at least 2 months without any considerable divergence in potentials. The proposed electrode shows high selectivity towards Ag⁺ ions over Pb²⁺, Cd²⁺, Co²⁺, Zn²⁺, Cu²⁺, Ni²⁺, Sr²⁺, Mg²⁺, Ca²⁺, Li⁺, K⁺, Na⁺, NH₄⁺ ions and can be used in a pH range of 2–6. Only interference of Hg²⁺ is found. It is successfully used as an indicator electrode in potentiometric titration of a mixture of chloride, bromide and iodide ions.     

Synthesis and evaluation of neutral anion receptors based on acylhydrazide-appended calix[4]arenes

A new class of neutral receptors based upon acylhydrazide-appended calix[4]arenes was synthesised and evaluated for recognition of anions. Detailed NMR and single-crystal X-ray analyses of one of the synthesised compounds reveal that anion recognition in such derivatives is achieved through cooperative hydrogen bond interactions. The presence of three centred NH–O and two OH–O hydrogen bonds at the lower rim of the synthesised calixarene architecture apparently helps the molecular scaffold to retain cone conformation to enable deployment of intermolecular hydrogen bonds for selective recognition of HSO₄ ^? ion in preference to F^?, Cl^?, Br^?, I^?, ClO₄ ^?, AcO^? and PF₆ ^? ions.     

Nickel Pyrazolyl Borate Complex: Synthesis,Structure, and Analytical Application as Benzoate Selective Sensor

The complex [Tp^Ph,MeNi(Cl)Pz^Ph,MeH] ( I ) [Tp^Ph,Me=hydrotris(3‐phenyl‐5‐methyl‐pyrazol‐1‐yl)borate; Pz^Ph,MeH=3‐phenyl‐5‐methyl‐pyrazole] has been synthesized and explored as ionophore for the preparation of a poly(vinyl chloride) (PVC) membrane sensor for benzoate anions. The formation constants for the interaction of complex I with different organic/inorganic anions in solution have also been studied by sandwich membrane method. PVC based membranes of I using tridodecylmethylammonium chloride (TDDMACl) as cation discriminator and o‐nitrophenyloctyl ether (o‐NPOE), dibutylphthalate (DBP), benzylacetate (BA) and tributylphosphate (TBP) as plasticizing solvent mediators were prepared and investigated as benzoate selective sensors. The best performance was shown by the membrane with composition (w/w) of I (5): PVC (150): NPOE (345): TDDMACl (0.3). The proposed sensor exhibits significantly enhanced selectivity toward benzoate ions over the concentration range 2.2×10^?6–1.0×10^?1 M with a lower detection limit of 1.4×10^?6 M and a Nernstian slope of 59.2 mVdecade^?1 of activity within a pH range of 4.5–8.5. The sensor has a response time of 12 s and can be used for at least 8 weeks without any considerable divergence in their potential response. The membrane sensor of complex I have been checked for reversible and accurate sensing of benzoate levels present in liquid food products.     

Ion transport studies in nanocomposite polymer electrolyte membrane of PVA–[C<Subscript>4</Subscript>C<Subscript>1</Subscript>Im][HSO<Subscript>4</Subscript>]–SiO<Subscript>2</Subscript>

The paper reports the effect of SiO₂ nano-filler on structural, thermal, and ion transport properties of polymer electrolyte system comprising polyvinyl alcohol (PVA) and 1-butyl-3-methylimidazolium hydrogen sulfate [C₄C₁Im][HSO₄] ionic liquid. The addition of SiO₂ nano-filler results into enhancement in amorphicity and thermal stability and lowering of glass transition temperature of the membranes. A detailed investigation of possible interactions among the constituents PVA, [C₄C₁Im][HSO₄] and SiO₂, and cation–anion and anion–anion pairs of [C₄C₁Im][HSO₄] in the polymer electrolyte and their dissociation due to SiO₂ filler has been carried out in the membranes using Fourier transform infra-red (FTIR) and Raman spectroscopy. The membranes show maximum room temperature ionic conductivity as 9.9?×?10^?3 S cm^?1 for 6 wt.% of the nano-filler which is about four times higher than the membrane without nano-filler and an order higher than pure [C₄C₁Im][HSO₄]. With temperature, the ionic conductivity shows VTF behavior in the temperature range 40–120 °C. On the basis of FTIR and ion transport results, a model for ion transport in the membranes is proposed.

Open image in new window

Graphical abstract Schematic model of ion transport in nanocomposite polymer electrolyte membrane of PVA-[C₄C₁Im][HSO₄]-SiO₂

     

Use of Tin (IV) Porhyrins as Ionophores for the Construction of Phthalate‐Selective Electrodes: Influence of the Structure and Membrane Composition on their Response Properties

Tin(IV) porphyrins derivatives were used as ionophores for phthalate selective electrodes preparation. The influence of ionophore structure and membrane composition (amount of incorporated ionic sites) on the electrode response, selectivity and long‐term stability were studied. Poly(vinyl chloride) polymeric membranes plasticized with o‐NPOE (o‐nitrophenyloctylether) and containing Sn(IV)‐tetraphenylporphyrin (TPP) dichloride (Sn(IV)[TPP]Cl₂) or Sn(IV)‐octaethylporphyrin (OEP) dichloride (Sn(IV)[OEP]Cl₂), and in some cases incorporating lipophilic cationic (tetraocthylammonium bromide ‐ TOABr) and anionic (sodium tetraphenylborate – NaTPB and potassium tetrakis[3,5‐bis(trifluoromethyl)phenyl]borate‐KTFPB) additives, were prepared and their potentiometric characteristics compared. Both ionophores are shown to operate via a neutral mechanism, and the addition of 10 mol % of lipophilic quaternary ammonium salt derivative to the membrane is required to achieve optimal electrode performance. The potentiometric units prepared, with Sn(IV)[TPP]Cl₂ (Type A) or Sn(IV)[OEP]Cl₂ (Type B) without additives, presented a slope of ?52.8 mV dec^?1 and ?58.8 mV dec^?1 and LLLR of 9.9×10^?5 mol L^?1 and 9.9×10^?6 mol L^?1, respectively. The units prepared using the same metalloporphyrins and incorporating 10% mol TOABr presented a slope of ?55.0 mV dec^?1 and ?57.8 mV dec^?1 and LLLR of 5.0×10^?7 mol L^?1 and 3.0×10^?7 mol L^?1. Their analytical usefulness was assessed by potentiometric determinations of phthalate in water and industrial products providing results that presented recoveries of about 100%.     

Determination of Tryptophan using a p-Sulfonated Calix [4,6,8]arene Modified Gold Electrode

The ability of p-sulfonated calix[n]arenes (n = 4, 6, 8) to form complexes with tryptophan was studied. The electrochemical properties of these complexes immobilized on gold surfaces were examined by cyclic voltammetry. Parameters affecting the performance of the modified electrodes including the arene concentration, scan rate, applied potential, and pH were optimized. Under the optimal conditions, the method had a linear response to tryptophan between 1 × 10^?7 M and 1 × 10^?5 M with a detection limit of 3 × 10^?8 M. The interaction of the tryptophan–p-sulfonated calix[4]arene complex was more stable than the tryptophan–p-sulfonated calix[6]arene and p-sulfonated calix[8]arene complexes. Molecular modeling calculations indicated that electrostatic interactions and structural matching effects were predominant stabilizing factors. The modified electrodes demonstrated good reproducibility and high selectivity, illustrating their effectiveness for analytical measurements.