The Factors Affecting the Electrochemiluminescence of Tris(2,2′‐bipyridyl)Ruthenium(II)/Tertiary Amines

Factors affecting tris(2,2′‐bipyridyl) ruthenium(II) (Ru(bpy)₃²⁺)/tertiary amine electrochemiluminescence (ECL) were investigated in the present work with several tertiary amines as coreactants. Some new phenomena different to those of traditional Ru(bpy)₃²⁺/tripropylamine were observed, such as the different responses of different coreactants to the hydrophobic nature of the working electrode and the ECL emission of triethanolamine at 0.85 V. The pK_a value (acid dissociation constant) for the deprotonation of tertiary amine group in the coreactant molecules and solubility of coreactants affect the ECL profiles vs. electrolyte pH. Moreover, the solubility of coreactants is also related to the ECL response to the addition of surfactants and electrode hydrophobic nature. Investigation of the effects of molecular structures indicated that molecules restricting the formation of the trigonal planar structure of the active radical in the electrooxidation procedure resulted in low ECL emission. The behaviors of hydroxyl and carboxylic group as substituents of α‐carbon are also totally different to the traditional opinions about the ECL from Ru(bpy)₃²⁺/tertiary amines.     

Electrogenerated Chemiluminescence Sensor Based on Tris(2,2′‐bipyridine)ruthenium(II)‐Immobilized Natural Clay and Ionic Liquid

A novel electrogenerated chemiluminescence (ECL) sensor based on natural clay and ionic liquid was fabricated. Tris(2,2′‐bipyridine)ruthenium(II) (Ru(bpy)₃²⁺) was immobilized on natural clay surface through simple adsorption. An ECL sensor was prepared by mixing Ru(bpy)₃²⁺‐incorporated clay, graphite powder and an ionic liquid (1‐butyl‐3‐methylimidazolium hexafluorophosphate) as the binder. The electrochemical behavior and ECL of the immobilized Ru(bpy)₃²⁺ was investigated. It was observed that the ECL of immobilized Ru(bpy)₃²⁺ was activated by the ionic liquid. The proposed ECL sensor showed high sensitivity to tri‐n‐propylamine (TPrA) and the detection limit was found to be 20 pM. In addition, the ECL sensor displayed good stability for TPrA detection and long‐term storage stability.     

Study on Electrochemiluminesce of Ru(bpy3)2+ Immobilized in a Titania Sol‐Gel Membrane

The immobilization of tris(2,2′‐bipyridyl)ruthenium(II), Ru(bpy)₃²⁺, at a glassy carbon electrode was achieved by entrapping the Ru(bpy)₃²⁺ in a vapor deposited titania sol‐gel membrane. The electrogenerated chemiluminescence (ECL) of the immobilized Ru(bpy)₃²⁺ was studied. The Ru(bpy)₃²⁺ modified electrode showed a fast ECL response to both oxalate and proline. The ECL intensity was linearly related to concentrations of oxalate and proline over the ranges from 20 to 700 μmol L^?1 and 20 to 600 μmol L^?1, respectively. The detection limits for oxalate and proline at 3σ were 5.0 μmol L^?1 and 4.0 μmol L^?1, respectively. This electrode possessed good precision and stability for oxalate and proline determinations. The electrogenerated chemiluminescence mechanism of proline system was discussed. This work provided a new way for the immobilization of Ru(bpy)₃²⁺ and the application of titania sol‐gel membrane in electrogenerated chemiluminescence.     

Determination of Total Calcium in Plasma by Flow Injection Analysis with Tris(2,2′‐bipyridyl)ruthenium(II) Electrochemiluminescent Detection

We described here a new method for the determination of total calcium in plasma. The method is based on the precipitation of calcium with excess oxalate and the measurement of residual oxalate by flow injection analysis with Ru(bpy)₃²⁺ electrochemiluminescent detection. It has the advantages of extremely stable reagent, user‐friendly instrument, high selectivity, good analytical recovery, wide dynamic range, and nice correlation with atomic absorption spectroscopy. The calibration plot for calcium is linear over a concentration range from 0.5 mmol L^?1 to 4.8 mmol L^?1, which is wider than those obtained by most other methods. The analytical recoveries for plasma calcium are 98.4–101.2% with coefficients of variation (CVs) of 1.96–2.52%. The within‐day CVs range from 0.76% to 0.95%, and between‐day CVs were from 1.12% to 1.46%. The time for each injection is one minute. Because the proposed method can be readily carried out on increasingly popular instruments for Ru(bpy)₃²⁺ ECL immunoassays and DNA probe assays, Ru(bpy)₃²⁺ ECL method is suitable for routine clinical analysis of calcium.     

Electrochemiluminescence of SDBS‐Ru(bpy)32+‐CPM System and Its Application

When the concentration of dodecyl benzene sulfonic acid sodium salt (SDBS) is 0.7 mmol·L^?1, the electrochemical and electrochemiluminescence (ECL) intensity of Ru(bpy)₃²⁺‐chlorpheniramine maleate (CPM) system at the Au electrode were studied. The results showed that compared with the absence of SDBS, enhancement of the ECL intensity was 14‐fold at Au electrode. Base on this, an ECL method was established for efficient and simple determination of CPM at Au electrode. Under the optimum experimental condition, the enhanced ECL intensities had good linear relationship with the concentration of CPM in the range of 1.0×10^?4–1.0×10^?7 mol·L^?1, and a linear regression equation was obtained as follows: I (counts)=48.805×10⁶c+394.03 (r=0.9975), the detection limit for CPM was 1.4×10^?8 mol·L^?1. The RSD for 5 times determinations of 1.0×10^?5 mol·L^?1 CPM was 3.2%. The results of recovery test were between 96.3%–102.5%, and the RSD of recovery test (n=5) was 2.7%. In addition, eleven kinds of tertiary amines‐Ru(bpy)₃²⁺ systems were investigated in the absence and presence of SDBS. The results showed that the enhancement of SDBS on ECL intensity of tertiary amines‐Ru(bpy)₃²⁺ systems was universal.     

基于Ru(bpy)32+-SiO2纳米颗粒的核酸适配体传感器对凝血酶的电致化学发光检测

本文应用核酸适配体构建了一种新型的电致化学发光检测蛋白体系。两个核酸适配体结合凝血酶的两个不同位点,利用这两核酸适配体与凝血酶的高亲和力构建三明治传感体系检测凝血酶。一个核酸适配体固定在金电极上用来捕获凝血酶,另一个标记有包裹电致化学发光活性物Ru(bpy)₃²⁺的二氧化硅纳米颗粒,用来检测电致化学发光信号。此核酸适配体传感器对凝血酶具有特异识别性,电致化学发光信号与凝血酶的浓度直接相关,非特异性识别的牛血红蛋白、牛血清白蛋白不干扰测定。由于在检测的核酸适配体上标记的纳米颗粒包裹有多个发光活性物,因此大大提高了发光效率和灵敏度,此法对凝血酶的线性响应范围为2.0 fmol•L^-1～2.0 pmol•L^-1,检测限可达1.0 fmol•L^-1。     

Effects of Divalent Metal Ions on Electrochemiluminescence Sensor with Ru(bpy)32+ Immobilized in Eastman‐AQ Membrane

Different effects of divalent metal ions on electrochemiluminescence (ECL) sensor with Ru(bpy)₃²⁺ immobilized in Eastman‐AQ membrane were investigated. Mg²⁺, Ca²⁺ and Fe²⁺ can elevate the ECL of Ru(bpy)₃²⁺/proline; while metal ions that underwent redox reactions on the electrode such as Mn²⁺ and Co²⁺ presented intensive quenching effects on Ru(bpy)₃²⁺ ECL. Also, the quenching effect of Mn²⁺ on the ECL sensor with Ru(bpy)₃²⁺ immobilized in Eastman‐AQ membrane enhanced to about 30‐folds compared with the case that Ru(bpy)₃²⁺ was dissolved in phosphate buffer, and the enhanced quenching effects of Mn²⁺ were studied.     

A Solid‐State Electrochemiluminescence Immunosensor Based on MWCNTs‐Nafion and Ru(bpy)32+/Nano‐Pt Nanocomposites for Detection of α‐Fetoprotein

A approach was successfully employed for constructing a solid‐state electrochemiluminescence (ECL) immunosensor by layer‐by‐layer self‐assembly of multiwall carbon nanotubes (MWCNTs)‐Nafion composite film, Ru(bpy)₃²⁺/nano‐Pt aggregates (Ru‐PtNPs) and Pt nanoparticles (PtNPs). The influence of Pt nanoparticles on the ECL intensity was quantitatively evaluated by calculating the electroactive surface area of different electrodes with or without PtNPs to immobilize Ru(bpy)₃²⁺. The principle of ECL detection for target α‐fetoprotein antigen (AFP) was based on the increment of resistance after immunoreaction, which led to a decrease in ECL intensity. The linear response range was 0.01–10 ng mL^?1 with the detection limit of 3.3 pg mL^?1. The immunosensor exhibited advantages of simple preparation and operation, high sensitivity and good selectivity.     

Electrochemiluminescence sensor using tris(2,2′-bipyridyl)ruthenium(II) immobilized in Eastman-AQ55D–silica composite thin-films

An electrochemiluminescence (ECL) sensor with good long-term stability and fast response time has been developed. The sensor was based on the immobilization of tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) into the Eastman-AQ55D–silica composite thin films on a glassy carbon electrode. The ECL and electrochemistry of Ru(bpy)₃²⁺ immobilized in the composite thin films have been investigated, and the modified electrode was used for the ECL detection of oxalate, tripropylamine (TPA) and chlorpromazine (CPZ) in a flow injection analysis system and showed high sensitivity. Because of the strong electrostatic interaction and low hydrophobicity of Eastman-AQ55D, the sensor showed no loss of response over 2 months of dry storage. In use, the electrode showed only a 5% decrease in response over 100 potential cycles. The detection limit was 1 μmol l⁻¹ for oxalate and 0.1 μmol l⁻¹ for both TPA and CPZ (S/N=3), respectively. The linear range extended from 50 μmol l⁻¹ to 5 mmol l⁻¹ for oxalate, from 20 μmol l⁻¹ to 1 mmol l⁻¹ for TPA, and from 1 μmol l⁻¹ to 200 μmol l⁻¹ for CPZ.     

Electrogenerated Chemiluminescence Ethanol Biosensor Based on Carbon Nanotube‐Titania‐Nafion Composite Film

Mesoporous titania‐Nafion composite doped with carbon nanotube (CNT) has been used for the immobilization of tris(2,2′‐bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) and alcohol dehydrogenase on an electrode surface to yield a highly sensitive and stable electrogenerated chemiluminescence (ECL) ethanol biosensor. The presence of CNT in the composite film increases not only the sensitivity of the ECL biosensor but also the long‐term stability of the biosensor. The present biosensor responds linearly to ethanol in the wide concentration ranges from 1.0×10^?5 M to 1.0×10^?1 M with a detection limit of 5.0×10^?6 M (S/N=3). The present ECL ethanol biosensor exhibited higher ECL response compared to that obtained with the ECL biosensor based on the corresponding composite without CNT. The present CNT‐based ECL biosensor showed good long‐term stability with 75% of its initial activity retained after 2 weeks of storage in 50 mM phosphate buffer at pH 7.0.     

Electrochemiluminescent behavior of allopurinol in the presence of Ru(bpy)(3)(2+)

The electrochemiluminescent (ECL) response of allopurinol was studied in aqueous media over a wide pH range (pH 2–13) using flow injection (FI) analysis. It was revealed that allopurinol itself had no ECL activity, but could greatly enhance the ECL of Ru(bpy)₃²⁺ in alkaline media giving rise to a sensitive FI-ECL response. The effects of experimental conditions including the mode of applied voltage signal, the potential of working electrode, pH value, the flow rate of carrier solution, and the concentration of Ru(bpy)₃²⁺ and allopurinol on the ECL intensity were investigated in detail. The most sensitive FI-ECL response of allopurinol was found at pH 12.0, where the FIA-ECL intensity showed a linear relationship with concentration of allopurinol in the range 1 × 10⁻⁸ mol L⁻¹ to 5 × 10⁻⁷ mol L⁻¹, and the detection limit was 5 × 10⁻⁹ mol L⁻¹.     

Electrochemiluminescent behavior of melatonin and its important derivatives in the presence of Ru(bpy)(3)(2+)

Melatonin and some of its important derivatives were found to be able to enhance the ECL of Ru(bpy)₃²⁺ in an alkaline Britton–Robinson buffer solution. The optimum conditions for the enhanced ECL, such as the selection of applied potential mode, type of buffer solution, pH effect and effect of Ru(bpy)₃²⁺ concentration have been investigated in detail in this paper. Under the optimum conditions, the enhanced ECL is linear with the concentration of melatonin and its derivatives over the wide range, and the detection limit for these compounds was found to be in the range of 5.0 × 10⁻⁸ to 1.0 × 10⁻¹⁰ mol L⁻¹. The proposed procedure was applied for the determination of drug in tablets with recoveries of 85–93%. A possible mechanism for the enhanced ECL of Ru(bpy)₃²⁺ by melatonin and its derivatives was proposed, and the relationship between molecular structure of melatonin and its derivatives and the enhanced ECL behavior was also discussed.     

A Novel Electrogenerated Chemiluminescence (ECL) Sensor Based on Ru(bpy)32+‐Doped Titania Nanoparticles Dispersed in Nafion on Glassy Carbon Electrode

A novel electrogenerated chemiluminescence (ECL) sensor based on Ru(bpy)₃²⁺‐doped titania (RuDT) nanoparticles dispersed in a perfluorosulfonated ionomer (Nafion) on a glassy carbon electrode (GCE) was developed in this paper. The electroactive component‐Ru(bpy)₃²⁺ was entrapped within the titania nanoparticles by the inverse microemulsion polymerization process that produced spherical sensors in the size region of 38±3 nm. The RuDT nanoparticles were characterized by electrochemical, transmission electron and scanning microscopy technology. The Ru(bpy)₃²⁺ encapsulation interior of the titania nanoparticles maintains its ECL efficiency and also reduces Ru(bpy)₃²⁺ leaching from the titania matrix when immersed in water due to the electrostatic interaction. This is the first attempt to prepare the RuDT nanoparticles and extend the application of electroactive component‐doped nanoparticles into the field of ECL. Since a large amount of Ru(bpy)₃²⁺ was immobilized three‐dimensionally on the electrode, the Ru(bpy)₃²⁺ ECL signal could be enhanced greatly, which finally resulted in the increased sensitivity. The ECL analytical performance of this ECL sensor for tripropylamine (TPA) was investigated in detail. This sensor shows a detection limit of 1 nmol/L for TPA. Furthermore, the present ECL sensor displays outstanding long‐term stability.     

Tris (2,2′-bipyridyl)ruthenium (III) as a chemiluminescent reagent for detection in capillary electrophresis

A post- column chemiluminescent technique for thedetection of compounds that are poor chromoshores using electorogenerated chemiluminescence following separation by capillartgy electrophoresis is described. The luminrescent signal is generated followintg the reaction of anlyres (e.g. amines) with Ru(bpy)₃³⁺, which isx electrochemically generated post-columan from Ru(bpy)₃²⁺. Tripropylamine and proline are used as two model compounds to demostrate the feasibility of the method. Detection limits for the prototype system were in the micromolar rage, suggesting that this technnique offers an alternative to indirect detection of compounds that are poor chromophores with an added selectivity advangage. The system includes the use of a conductive joint to isolate the separation field from the potential necessary to drive the elctrogenerated chemiluminescent reactiion. Addition of the chemiluminescent reagent Ru(bpy)₃²⁺ post-column did not decrease the efficiency of the separation. The design and favrication of the novel cell is discussed.     

Electrogenerated Chemiluminescence of Tris(2,2′‐bipyridyl)ruthenium(II) Immobilized in Humic Acid‐Silica‐Poly(vinyl alcohol) Composite Films

In this paper, we report the first attempt to use humic acid (HA) as modifiers to prepare the organic‐inorganic hybrid modified glassy carbon electrodes based on HA‐silica‐PVA (poly(vinyl alcohol)) sol‐gel composite. Electroactive species of tris(2,2′‐bipyridyl)ruthenium(II) (Ru(bpy) ) can easily incorporate into the HA‐silica‐PVA films to form Ru(bpy) modified electrodes. The amount of Ru(bpy) incorporated in the composite films strongly depends on the amount of HA in the hybrid sol. Electrochemical and electrogenerated chemiluminescence (ECL) of Ru(bpy) immobilized in HA‐silica composite films coated on a glassy carbon electrode have been studied with tripropylamine (TPA) as the coreactant. The analytical performance of this modified electrode was evaluated in a flow injection analysis (FIA) system with a homemade flow cell. The as‐prepared electrode showed good stability and high sensitivity. The detection limits (S/N=3) were 0.050 μmol L^?1 for TPA and 0.20 μmol L^?1 for oxalate, and the linear ranges were from 0.10 μmol L^?1 to 1.0 mmol L^?1 for TPA and from 1.0 μmol L^?1 to 1.0 mmol L^?1 for oxalate, respectively. The resulting electrodes were stable over two months.     

有机改性溶胶-凝胶固定联吡啶钌修饰电极的电化学行为

采用有机改性溶胶一凝胶制备技术,以四甲氧基硅烷(TMOW)和二甲基二甲氧基硅烷(OiMe-DiMOS)为共先驱体包埋聚苯乙烯磺酸钠(PSS),通过离子交换成功地将联吡啶钌固定在玻碳电极表面。电化学研究结果表明,被固定的联吡啶钌保持了良好的电化学活性,同时该方法制备的修饰电极对甲基安非他明有灵敏的电化学响应。     

Determination of Cu2+ in Drinking Water Based on Electrochemiluminescence of Ru(phen)32+ and Cyclam

A convenient and simple electrochemiluminescence (ECL) method was employed to detect trace amounts of Cu²⁺ in drinking water. This method is based on the inhibitory effect of Cu²⁺ on the ECL of Ru(phen)₃²⁺ and 1,4,8,11‐tetraazacyclotetradecane (cyclam) system. ECL intensity of Ru(phen)₃²⁺ was considerably enhanced by the addition of cyclam because of the ECL reaction between them. The ECL intensity of Ru(phen)₃²⁺/cyclam system rapidy decreased with the addition Cu²⁺ because of the formation of chelate complex [Cu(cyclam)]²⁺. Good linear response (R ²=0.9948) was obtained at Cu²⁺ concentration of 1.0×10⁻⁹−1.0×10⁻⁵ mol ⋅ L⁻¹ at glassy carbon electrode in 0.1 mol ⋅ L⁻¹ phosphate buffer (pH 9.0). Observed detection limit of 4.8×10⁻¹⁰ mol ⋅ L⁻¹ satisfied the maximum contaminant level goal (MCLG) for Cu²⁺ set by the US Environmental Protection Agency (US EPA). Applicability of the proposed method was verified by the good reproducibility and stability of the method when applied to determine Cu²⁺ in tap water and simulated wastewater. Thus, a novel ECL detection method was developed for Cu²⁺ detection.     

Synthesis and Characterization of Heteroleptic Ru(II) Complexes Based on 4,4′‐Bis((E)‐styryl)‐2,2′‐bipyridine as Ancillary Ligand and Application for Dye‐Sensitized Solar Cells

Heteroleptic Ru(II) complexes were designed based on 4,4′‐bis((E)‐styryl)‐2,2′‐bipyridine (bsbpy) as an ancillary ligand for dye‐sensitized solar cells (DSSCs), and those Ru(II) sensitizers, [Ru(L)(bsbpy)(NCS)₂][TBA] (TBA; tetrabutylammonium), were synthesized according to a typical one‐pot reaction of [RuCl₂(p‐cymene)]₂ with the corresponding anchoring ligands (where L = 4,4′‐dicarboxy‐2,2′‐bipyridine (dcbpy), 4,4′‐bis((E)‐carboxyvinyl)‐2,2′‐bipyridine (dcvbpy), 4,7‐dicarboxy‐1,10‐phenanthroline (dcphen), or 4,7‐bis((E)‐carboxyvinyl)‐1,10‐phenanthroline (dcvphen)). The new Ru(II) dyes, [Ru(L)(bsbpy)(NCS)₂][TBA] that incorporated vinyl spacer(s) into ancillary and/or anchoring ligand displayed red‐shifted bands over the overall UV/VIS region relative to the absorption spectra of N719 . A combination of bsbpy ancillary and dcphen anchoring ligand showed the best result for the overall power conversion efficiency (η); i.e., a DSSC fabricated with [Ru(dcphen)(bsbpy)(NCS)₂][TBA] exhibited a power conversion efficiency (η) of 2.98% (compare to N719 , 4.82%).