多孔硅的光致发光机制

人们已经提出了许多解释多孔硅发光的理论模型,每个模型都可以针对某些实验现象做出合理的解释,而对其他的实验结果就可能无法解释甚至相悖,因此多孔硅的发光机制至今仍是需要进一步研究和解决的问题。通过改变阳极氧化的条件,制得了一系列样品,其光致发光谱主要有四个峰。随着制备条件的改变,各个峰位的变化不大,但峰值强度比的变化比较大。随着自然氧化时间的延长,各个峰位的变化很小,有红移也有蓝移,有的则基本不变;而峰值强度的减弱幅度较大,但对应于各个峰位幅度的减弱是均衡的。分析实验现象产生的原因,认为多孔硅的发光是多种发光机制共同作用的结果;多孔硅纳米量子线的一定尺寸分布,不仅使光致发光谱存在一定的带宽,而且也是产生多峰现象的原因之一;多孔硅的结构特征对其发光特性起着决定性的作用。     

多孔硅微秒光致发光衰减

在微秒范围内测量了多孔硅的光致发光衰减,研究了衰减参数与发光波长、样品制备条件的关系,发现衰减参数与发射波长有关,但不依赖于样品制备条件。用发光三层模型解释了实验结果。     

提高多孔硅传感特性的一种新方法(英文)

研究了多孔硅(PS)吸附有机溶剂分子后对多孔硅荧光谱的淬灭效应。结果表明:淬灭多孔硅发光的有机溶剂分子是极性分子,有机溶剂分子的极性不同对多孔硅发光的淬灭程度也不同,且有些有机溶剂分子吸附氧化多孔硅比吸附多孔硅引起的发光淬灭具有更好的可逆性和选择性;用含有胺基的正丁胺(CH3CH2CH2CH2-NH2)作碳源,用射频辉光放电等离子系统在多孔硅表面沉积c n膜对多孔硅进行钝化处理后发现:其电致发光强度明显增强,发光峰位兰移,且在大气中存放60天后,其电致发光谱强度基本不衰减,峰位不再移动。经钝化处理的器件较未经处理的器件具有小的串联电阻Rs和低的驱动电压。这为提高多孔硅的传感特性提供了一种新方法。     

多孔硅的制备条件对其光致发光特性的影响

不同的实验条件下制备的多孔硅的光致发光(PL)特性是不同的,这是许多研究产生分歧的主要原因。对比分析了阳极氧化电流密度、阳极氧化时间、溶液浓度以及自然氧化时间对多孔硅光致发光光谱的影响。认为在一定的范围内,多孔硅的发光峰位会随电流密度的增大而蓝移,要获得较强的发光,需要选择合适的电流密度;随着腐蚀时间的延长,多孔硅的发光峰位也发生蓝移。当HF酸的浓度较小时,峰位随浓度的增大表现为向低能移动;而当HF酸的浓度较大时,峰位随浓度的增大则表现为移向高能。多孔硅在空气中自然氧化,其发光峰位发生蓝移,而发射强度随放置时间的延长而降低。并用量子限制模型和发光中心模型对实验结果进行解释。     

铜掺杂多孔硅的光致荧光猝灭

采用浸泡镀敷的方法在多孔硅表面形成了一铜镀层,通过对掺铜前后多孔硅的光致发光(PL)谱和傅里叶变换红外(FTIR)吸收光谱的研究,讨论了铜在多孔硅表面的吸附对其光致发光的影响。实验表明,掺铜对多孔硅的光致发光具有明显的猝灭效应,并使多孔硅的发光峰位蓝移。由于多孔硅表面铜的吸附使硅-氢键明显减少,而铜原子和硅的悬挂键成键会形成新的非辐射复合中心,从而使多孔硅的光致发光强度衰减。且浸泡溶液的浓度越高,这种猝灭效应越明显。而多孔硅发光峰位的蓝移,则是由于在发生金属淀积的同时伴随着多孔硅表面Si的氧化过程(纳米Si氧化为SiO2)的缘故。     

多孔硅光致发光的温度效应研究

通过对多孔硅光致发光峰随测量温度变化的研究，发现随测量温度的下降，光致发光峰位有两种截然不同的移动方向：发光峰中心波长较长的样品，主峰向低能方向移动(即红移)；而发光峰位波长较短的样品则向高能方向移动(即蓝移).根据多孔硅光致发光峰的温度效应，定性地给出了发光效率随波长变化的模拟曲线，并由此能较好地解释多孔硅光致发光峰位随温度变化而移动的实验现象. 关键词：     

掺钛化学腐蚀法制备发光稳定的多孔硅

本文采用掺钛化学腐蚀法制备出了发光稳定性和均匀性都较好的多孔硅 (PS)。存放和退火试验表明 ,光致发光 (PL)谱峰位不蓝移 ,强度不衰减。多孔硅发光稳定性的提高归因于制备过程中样品表面原位氧和钛的钝化。钛的浓度和腐蚀时间对PL强度有明显影响 ,最佳钛浓度约为 0 0 8mol·L- 1 ,最佳腐蚀时间约为 2 0min。掺钛化学腐蚀法制备的PS的光激发过程符合量子限域机制 ,而其PL过程却与量子限域模型不符 ,这表明其光发射过程不是带 带直接跃迁产生的 ,即存在一个表面态     

多孔硅的表面碳膜钝化

报道对多孔硅（ＰＳ）进行碳膜（ＣＦ）钝化处理的结果。红外吸收光谱表明,经钝化处理样品的表面由Ｓｉ－Ｃ、Ｓｉ－Ｎ和Ｓｉ－Ｏ键所覆盖;荧光我谱表明,经钝化处理的样品较未处理的样品发光强度提高４￣４．５倍,且发光峰位明显蓝移;存放实验显示,经钝化处理的样品发光强度稳定、发光峰位不变。这些结果表明正丁胺可以在多孔硅表面形成优良的钝化碳膜,是一种十分有效的多孔硅后处理途径。     

铁钝化多孔硅中的输运性质

采用水热法制备了发光强度强且不衰减、峰位不蓝移的铁钝化多孔硅。标准四引线法测得的电阻一温度结果表明杂质能级是输运的主宰者;电流一电压结果说明当有电流流过样品时会有明显的热效应．考虑到金属电极和铁钝化多孔硅之间形成的肖特基势垒会对样品的输运性质产生影响,采用其平面的两引线法测量了铁钝化多孔硅样品在不同温度下的电流一电压特性,发现隧道模型可以很好地拟和这些结果这些研究结果指出作为未来的多孔硅光电集成器件;通过多孔硅的电流必须限定在一定的范围１引言 １９９０年英国的Ｌ．Ｔ,Ｃａｎｈａｍ首次成功获得在室…     

CdS纳米颗粒填充的自支撑多孔硅光致发光特性

为了研究CdS纳米颗粒填充的自支撑多孔硅的光致发光特性,选用电阻率为0.01~0.02Ω·cm的P型硅片,先采用二步阳极氧化法制备自支撑多孔硅,再利用电泳法将CdS纳米颗粒填充入该自支撑多孔硅中.采用扫描电子显微镜、X射线能谱分析、X射线衍射分析、光致发光谱分析对所制备样品的形貌、相结构、组份及发光性能进行研究.实验结果表明:自支撑多孔硅内部成功填充了CdS纳米颗粒,该CdS纳米颗粒衍射峰为(210);CdS纳米颗粒填充的自支撑多孔硅光致发光峰峰位发生红移,且从570nm转移到740nm;电泳时间直接影响CdS纳米颗粒的填充量,导致相关的发光峰强度及发光峰位明显不同.     

The Influence of Immersion of Porous Silicon in Aqueous Solutions of Fe(NO<Subscript>3</Subscript>)<Subscript>3</Subscript> on Photoluminescence during Long Storage

The interaction of porous silicon (PS) with aqueous solutions of Fe(NO₃)₃ with different molar (M) concentrations causes introduction of iron ions into silicon pores (PS–Fe), formation of adsorbed iron coatings with different thicknesses, and an increase in the stability of PS layers, which is important for development of device structures based of PS. To treat PS layers with solutions by the immersion method, it is necessary to determine how this affects the spectral composition and intensity of photoluminescence (PL), as well as the kinetics of PL changes during long storage under atmospheric conditions. Upon treatment of freshly prepared PS by immersion into in a Fe(NO₃)₃ aqueous solution, it was found that, after short-term storage (up to 5 days) of the PS samples, the PL intensity increases by 7.5 and 3–3.6 times at low (0.2 M) and high (0.7–0.8 M) concentrations of Fe(NO₃)₃, respectively, compared to the PL intensity of an untreated PS layer. After long-term storage (4 months), the PL intensity of PS–Fe samples with concentrations of 0.1–0.2 and 0.7–0.8 M was observed to considerably increase (by 8–18 times) with unchanged position of the PL peak with respect to untreated PS. However, at the Fe(NO₃)₃ concentration of 0.3 М, the PL intensity decreases and the PL peak shifts to the blue, which is explained by incomplete coverage of the PS surface by an adsorbed iron layer. The kinetics of PL spectra during long-term storage is analyzed, and a model is proposed to explain the PL intensity and spectral composition.     

Er3+、In3+等金属离子对多孔硅光致发光性质的影响

用阳极腐蚀的方法制备了多孔硅样品,用电化学方法在多孔硅中注入Ｅｒ＾３＋、Ｉｎ＾３＋等金属离子,并对注入离子后多孔硅的光致荧光光谱进行了研究,结果表明：注入Ｅｒ＾３＋及Ｉｎ＾３＋后的多孔硅在５８８ｎｍ处的妇光峰强度大大增加,同时发光峰稍有展宽。随着离子注入时间的增长,强度继续增加,但当离子溶液浓度一定时,这种增强对时间具有饱和性。     

Photoluminescence enhancement and stabilisation of porous silicon passivated by iron

Iron is incorporated in porous silicon (PS) by impregnation method using Fe(NO₃)₃ aqueous solution. The presence of iron in PS matrix is shown from energy-dispersive X-ray (EDX) analysis and Fourier transform infrared (FTIR) measurements. The optical properties of PS and PS-doped iron are studied by photoluminescence (PL). The iron deposited in PS quenched the silicon dangling bonds then increased the PL intensity. The PL peak intensity of impregnated PS is seven times stronger than that in normal PS. Upon exposing iron-PS sample to ambient air, there is no significant change in peak position but the PL intensity increases during the first 3 weeks and then stabilises. The stability is attributed to passivation of the Si nanocrystallites by iron.     

制备多孔硅的一种新方法

自从Canham观察到多孔硅(PS)的可见光致发光后,由于其可望成为可与Ⅲ—Ⅴ族半导体材料相媲美的新型光电子材料而引起了科学界极大的兴趣.目前,制备多孔硅一般都采用电化学腐蚀方法.     

多孔硅的一种新的后处理方法──微波等离子体辅助钝化处理

报道了对多孔硅进行后处理的一种新方法，即真空中微波等离子体辅助的钝化处理．傅里叶变换红外吸收谱表明，经处理的样品表面主要是被SiS_x和SiO_y所覆盖．与未经处理的样品相比，其发光强度增加约3.5倍，PL峰位蓝移了40nm，而且在空气条件下存放60d后发光强度没有变化．表明这种方法是增加多孔硅发光强度和提高稳定性的有效方法之一．     

激光促进多孔硅内表面氧化与光致发光的退化

本文对刚制备的以及分别经以下三种情况:1.样品在1大气压的氧气中经激光(Ar~+激光器的48.80nm线,功率密度为1.77W/cm~2)连续照射1小时;2.样品在1大气压的氧气中在没有激光照射的情况下保持1小时;3.样品在1.3×10~2Pa真空度下用激光连续照射1小时处理后的多孔硅在室温下进行了光致发光谱和傅里叶变换红外吸收测量,研究了处理前后光谱的变化。实验发现经第一种情况处理后光致发光峰位蓝移了约0.1eV,发光强度衰减了二十几倍,相应的其红外光谱中与氧有关的吸收峰强度大幅度增长,而经第二,三两种情况处理后它们的光致发光及红外吸收谱则无大的变化。研究表明在氧气中激光辐照能大大加速多孔硅内表面的氧化。我们认为很可能是多孔硅内表面的氧化作用使光致发光峰位蓝移,由氧化作用产生的非辐射复合中心导致光致发光效率的下降。     

Effect of annealing on structural, optical and electrical properties of ZnS/porous silicon composites

ZnS films were prepared by pulsed laser deposition (PLD) on porous silicon (PS) substrates. This paper investigates the effect of annealing temperature on the structural, morphological, optical and electrical properties of ZnS/PS composites by x-ray diffraction (XRD), scanning electron microscope (SEM), photoluminescence (PL) and I--V characteristics. It is found that the ZnS films deposited on PS substrates were grown in preferred orientation along β-ZnS (111) direction, and the intensity of diffraction peak increases with increasing annealing temperature, which is attributed to the grain growth and the enhancement of crystallinity of ZnS films. The smooth and uniform surface of the as-prepared ZnS/PS composite becomes rougher through annealing treatment, which is related to grain growth at the higher annealing temperature. With the increase of annealing temperature, the intensity of self-activated luminescence of ZnS increases, while the luminescence intensity of PS decreases, and a new green emission located around 550~nm appeared in the PL spectra of ZnS/PS composites which is ascribed to the defect-center luminescence of ZnS. The I--V characteristics of ZnS/PS heterojunctions exhibited rectifying behavior, and the forward current increases with increasing annealing temperature.     

多孔硅镍钝化处理的光致发光谱研究

报道了对多孔硅在NiCl2中电解钝化处理的一种新方法,观测了经不同时间处理后多孔硅的光致发光谱,其光谱表明,恰当的处理条件,可使峰值强度增大约2．5倍,峰值波长蓝移33nm,分析了现象发生的原因是由于多孔硅表面的SiHx中的H被Ni替换成SiNix的结果。     

Emission mechanisms in stabilized iron-passivated porous silicon: Temperature and laser power dependences

Photoluminescence (PL) measurements of porous silicon (PS) and iron-porous silicon nanocomposites (PS/Fe) with stable optical properties versus temperature and laser power density have been investigated. The presence of iron in PS matrix is confirmed by Raman spectroscopy. The PL intensity of PS and PS/Fe increases at low temperature, the evolution of integrated PL intensity follows the modified Arrhenius model. The incorporation of iron in PS matrix reduces the activation energy traducing the existence of shallow levels related to iron atoms. Also, the temperature dependence of the porous silicon PL peak position follows a linear evolution at high temperature and a quadratic one at low temperature. Such evolution is due to the thermal carriers' redistribution and an energy transfer. Similarly, we have compared the laser power dependence of the PL in PS and PS/Fe layers. The results prove that the recombination process in PS is realised through the lower energy traps localised in the electronic gap. However, the observed emission in PS/Fe is essentially due to direct transitions. So, we can conclude that the presence of iron in PS matrix induces a strong modification of the PL mechanisms.