Application of Ultrasonic Attenuation Measurements in the Studies on Macromolecular Conformational Behaviors

——Phase Behavior of the Aqueous Solution of Poly(vinyl methyl ether) Sensitive to Temperature and the Modification of the Behavior by Using Poly(acrylic acid) The phase behavior of the aqueous solution of poly(vinyl methyl ether) (PVME) sensitive to temperature and the modification of the behavior by using poly(acrylic acid) (PAA) have been studied by ultrasonic attenuation measurements and fluorescence probe techniques. It has been observed that PVME solution is transparent at room temperature and becomes turbid upon heating. The solution turns clear again as soon as the temperature is decreased to room temperature. The heating and cooling process can be repeated for many times. The phase behavior of the solution sensitive to temperature is attributed to the conformational changes of the polymer. PVME may adopt an open coil conformation at room temperature. With this conformation, the polymer is well miscible with the solvent, water, and thereby the system is a real solution. The polymer may adopt a compact coil conformation when the temperature is higher than a specific value, which is called the LCST (the lower critical solution temperature) of PVME. In this case, the polymer tangles to each other and forms various aggregates, which can scatter incident light and ultrasonic waves greatly, resulting in the phase separation. Introduction of PAA decreases the temperature sensitivity of the phase behavior of the polymer. The nature of the inhibition is attributed to the complexation of PAA with PVME and the strong hydrophilicity of PAA. Results from fluorescence probe studies are in accordance with those from ultrasonic attenuation measurements, indicating again that the ultrasonic attenuation method can be successfully used for the qualitative studies of polymer conformations and complexation between polymers.     

Insulin release behavior of poly(N-isopropylacrylamide-co-N-vinyl-2-pyrrolidone) hydrogel based on modified melamine crosslinkers

Novel hydrogels based on poly(N-isopropylacrylamide-co-N-vinyl-2-pyrrolidone) (PNIPAAm/PNVP), were synthesized by solution radical polymerization using water as solvent and different weight percentage of crosslinkers ranging from 0.5 to 4%. The monomer mol ratios of NIPAAm/VP (0.9/0.1, 0.5/0.5, and 0.1/0.9) were used in all cases. N,N′-methylenebisacrylamide (MBA) and the new synthesized N,N,N-triacrylamido melamine (MAAm) were used as crosslinkers. The swelling parameters such as the swelling ratio Q, equilibrium water content (EWC), volume fraction of polymer φ_p and volume fraction at crosslinking φ_r were calculated from swelling measurements at different temperatures. The lower critical solution temperatures (LCST) of the prepared hydrogels were measured using DSC technique. The data of LCST indicated that the NIPAAm/VP crosslinked with MAAm or MBA showed reversible swelling and shrinking with temperature changes. The temperature dependence of swelling ratio and response kinetics upon heating or cooling was also investigated to understand the smart properties, i.e., temperature sensitive properties of these smart hydrogels. The in vitro release experiments were carried out at 22 and 37°C, respectively, to investigate the effect of temperature-sensitive property of these PNIPAAm/PNVP hydrogels crosslinked with MAAm and MBA crosslinkers on insulin release profiles.     

Thermoreversible gelation on cooling and on heating of an aqueous gelatin–poly(N-isopropylacrylamide) conjugate

A polymer conjugate composed of 43 wt% gelatin and 57 wt% poly(N-isopropylacrylamide) (PNIPAAm) was prepared. The dynamic viscoelastic properties of an aqueous solution of the conjugate at the concentration of 5 wt% were examined. The solution was viscous fluid at 30°C and turned into an elastic homogeneous hydrogel upon heating above 34°C or upon cooling below 10°C. The resultant hydrogels turned back into a solution at the opposite temperature cycles of the gelation. It is considered that the driving force of the gelation is the intermolecular hydrophobic interaction of PNIPAAm blocks or the intermolecular helix association of gelatin blocks, respectively, on heating or on cooling. © 1998 John Wiley & Sons, Ltd.     

Thermo-reversible swelling of thin hydrogel films immobilized by low-pressure plasma

Thin films of graft copolymers consisting of poly(N-isopropylacrylamide) (PNiPAAm) or poly(N,N-diethylacrylamide) (PDEAAm) as polymer backbone and poly(ethyleneglycol) as side chains were cross-linked on fluoropolymer substrates by low-pressure plasma treatment. All immobilized polymers exhibit a lower critical solution temperature between 34 and 40 degrees C. The swelling and collapsing of the hydrogels was examined with temperature-dependent spectroscopic ellipsometry. Two time ranges of swelling were observed: a fast 'dynamic' and a slow 'equilibrium' swelling. The dynamic swelling occurs within minutes or less, whereas the equilibrium swelling needs several days to complete. The surface-bound hydrogels show a shift in the transition temperature toward lower temperatures compared with the behavior in solution. Full reversibility of the dynamic swelling/collapsing was found, but the temperature scan exhibits a hysteresis between heating and cooling cycles. The PNiPAAm-containing hydrogels show a sharper transition compared to the PDEAAm-containing hydrogels, which is almost linear over a wide temperature range.     

Effects of synthesis-solvent on swelling and elastic properties of poly(N-isopropylacrylamide) hydrogels

Thermosensitive N-isopropylacrylamide (NIPA) hydrogels were synthesized by a free radical copolymerization with N,N′-methylenebisacrylamide (MBAA) in four solvents: water, ethanol, acetone and N,N-dimethylformamide. The swelling and elastic properties of the hydrogels were affected by the synthesis-solvents; the hydrogels (e.g. NIPA/MBAA = 1000/50 mol/m³-pre-gel solution) synthesized in water have smaller swelling volume and larger shear modulus at 10 °C than those synthesized in amphiphilic solvents. The network structure of hydrogels was estimated in terms of the conversion and two sorts of effective crosslinking density based on the Flory theory and the concentration of crosslinker. The hydrogels synthesized in water can have the microscopic inhomogeneous network arising from the entanglement of polymer chains, while the hydrogels synthesized in amphiphilic solvents can have the homogeneous network arising from the polymer concentration lower than the pre-gel solution and can be similar in network structure to the lightly crosslinked hydrogel synthesized in water.     

P(NIPAM-co-NVP)共聚物分子链水溶液中的可逆聚集研究

用溶液聚合方法合成了线型聚(N-异丙基丙烯酰胺-co-N-乙烯基吡咯烷酮)共聚物,通过弹性光散射(elastic light scattering,ELS)、荧光光谱与动态光散射研究了共聚物水溶液分子链可逆聚集的温度和时间依赖性.研究表明,升温时,ELS强度增加,分子链聚集;降温时,ELS强度降低,聚集的分子链解离.荧...     

Side‐chain conformational changes during the thermoshrinking process: γ‐Ray polymerization and spectroscopic study of uncrosslinked poly(methacryloyl‐Ala‐OMe)

Poly(methacryloyl‐L ‐alanine‐methyl ester) (1) has an optically active side chain and consists of thermoshrinking hydrogels upon crosslinking. We synthesized an uncrosslinked polymer of 1 by the γ‐ray polymerization method. For the prepared polymer, variable‐temperature circular dichroism (CD) and ¹H NMR spectra were studied, and we found conformational changes in the optically active side chains during the thermally induced phase transition. Intense CD spectra reveal ordered conformation in the side chain of 1 below the phase transition temperature (∼28 °C). A well‐resolved ¹H NMR spectrum of 1 at 0 °C shows that the conformational angles in the polymer side chain are fixed at low‐energy minima. With increasing temperature, the frozen side chain starts rotating vigorously and takes an unordered orientation. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2671–2677, 2000     

采用流变学方法研究聚酰胺酸6FDA-TFDB溶液的降解行为

合成了一种聚酰胺酸6FDA-TFDB溶液,利用流变仪研究其在不同影响因素(如:温度、升温速率、溶剂含水量等)下的流变行为,发现聚酰胺酸溶液的降解在高温区和低温区存在不同的行为.通过Andrade公式获得不同条件下聚酰胺酸溶液的黏流活化能,并比较其差异,同时对溶剂水含量在不同温度区域下对聚酰胺酸降解速率的影响也进行了深入的分析,从而建立一种半定量比较不同条件下聚酰胺酸溶液降解速率的方法.     

Reaction of syndiotactic poly(methacrylic acid hydrazide) with functional carboxylic acids

As a highly reactive tactic vinyl polymer, syndiotactic poly(methacrylic acid hydrazide) (s-PMH) was prepared from syndiotactic poly(methyl methacrylate) (s-PMMA) by hydrazinolysis. The s-PMH served as the starting polymer to prepare other tactic vinyl homopolymers having optically active functional carboxylic acids or N-protected amino acids as side chains. The condensation of the acids was carried out in water by water-soluble carbodiimides. Conversion was followed by pH and the resulting homopolymers characterized by ¹H- and ^13C-NMR spectroscopy. The NMR-spectra were assigned by comparison with low molecular weight model compounds, derived from pivalic acid hydrazide. In a third on-polymer reaction, the OH-groups present in the side chains of some of the polymers were employed for adding an optically active isocyanate to yield branched side chains.     

Unusual phase behavior in mixtures of poly(ethylene oxide) and ethyl alcohol

Poly(ethylene oxide) (PEO), soluble in both aqueous and organic solvents, is one of the most intriguing polymers. PEO solution properties have been extensively studied for decades; however, many of the studies have focused on specific properties, such as clustering, of PEO in aqueous solutions, and the behavior of PEO in organic solvents has not been adequately explored. The results presented here demonstrate that PEO crystallizes into a lamellar structure in ethyl alcohol after the mixture is quenched to room temperature from a temperature above the crystal melting point. Above the melting temperature, PEO completely dissolves in ethyl alcohol, and the mixture exhibits regular polymer solution thermodynamic behavior with an upper critical solution temperature (UCST) phase diagram. Remarkably, the UCST phase boundary is significantly below the melting temperature, and this indicates that the system undergoes a crystallization process before the phase separation can occur upon cooling and, therefore, possesses an unusual phase transition. The phase transition from the crystalline state to the miscible solution state is reversible upon heating or cooling and can be induced by the addition of a small amount of water. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 557–564, 2006     

Application of Ultrasonic Attenuation Measurements in the Studies on Macromolecular Conformational Behaviors——Phase Behavior of the Aqueous Solution of Poly(vinyl methyl ether) Sensitive to Temperature and the Modification of the Behavior by Using Pol

Introduction Studies on the conformational and aggregation be-haviors of macromolecules in aqueous solution and at solid/liquid interfaces have been highlighted in colloid and interface science since the early 1990s.1-3 It was mentioned in the first part of this series of studies that development of new methods, which are characterized by being in time and non-destructive and can be used for monitoring the conformational and aggregation be-havior of macromolecules, is of critical importance fo…     

Influence of the bulkiness of the substituent on the aggregation and magnetic properties of poly(3‐alkylthiophene)s

A series of poly(3‐alkylthiophene)s (P3ATs) ( P1–P5 ) has been synthesized via a Ni(dppp)‐mediated polymerization, varying the bulkiness of the alkyl side chains in order to investigate the influence of the bulkiness of the alkyl substituent on the aggregation and magnetic properties of P3ATs. UV–Vis spectroscopy, performed in solution as well as in film, shows that the stacking of the polymers becomes more complicated as the bulkiness of the side chains increases. Both the π‐interactions and the planarization of the polymer chains are diminished. While aggregation is absent in poor solvent for the polymer with the most bulky side chains, aggregation was present in film, albeit slowed down. This behavior was also confirmed by X‐ray diffraction (XRD) and differential scanning calorimetry (DSC) experiments. Electron spin resonance (ESR) measurements, performed at 300 K on powders, confirmed the trend of decreasing supramolecular order with increasing bulkiness of the side‐chain. Magnetization measurements, performed at 5 and 300 K, are in line with our hypothesis on the influence of π‐interactions and the fraction of planar polymer chains on the coercivity and saturation magnetization, respectively. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 76–86     

Rheological behavior and reversible swelling of pH sensitive poly(acrylamide-<Emphasis Type="Italic">co</Emphasis>-itaconic acid) hydrogels

The study involved preparation of poly(acrylamide-co-itaconic acid) hydrogels by radical cross-linking copolymerization. The copolymer hydrogels were characterized through infrared spectroscopy, thermal analysis, swelling measurements and in oscillatory and steady shear rheology. Results showed that more stable copolymers were formed due to the strong interaction in the hydrogels. These hydrogels have shown substantial percent swelling in water and shrinking in saline solution and acidic buffers. The rheological properties were described by the Herschel-Bulkley and power-law models to explore their non-Newtonian behavior. The results showed that higher itaconic acid content raised the polymer viscosity; the degree of shear-thinning and polymer elasticity (G′) were also increased. The transition from the viscous (G′ < G″) to the predominant viscoelastic behavior (G′ > G″) occurs at a crossover frequency ranged from 17.8 rad/s for polyacrylamide to 15.7, 12.8 and 12.5 rad/s for copolymers.     

Solubility and Solution Structure of Cellulose Derivatives

Strongly interacting solvents are needed to dissolve cellulose; therefore, in the past the interpretation of the uncommon solution behavior of cellulose and its derivatives was based mainly on energetic (enthalpic) considerations, for example, hydrogen bonding. These attempts have not been very successful. The present paper demonstrates that entropic effects influence the solution behavior much stronger than hitherto supposed. In the well-known Flory–Huggins theory the driving force for dissolution of flexible chains is the configurational entropy of mixing. This large entropy is strongly reduced by the chain stiffness of the cellulose backbone and by the strictly regular primary structure of this polysaccharide. It strongly reduces the driving force for dissolution. The entropy of mixing becomes largely increased again by the attachment of long side chains and causes solubility with surprising efficiency (hairy rod principle). This effect is demonstrated with several examples. Among others, the surprising insolubility of short, regular-selectively substituted cellulose chains is explained, although long chains of the same substitution pattern are soluble. The striking behavior of cellulose ethers in water is based on the hydrophobic effect, which causes an increased order of the polymer surrounding water molecules. The induced order results in a very pronounced decrease of entropy of mixing that overcompensates the positive configurational entropy of mixing. Common rules of basic thermodynamics now predict phase separation on heating, contrary to the Flory–Huggins theory, which can only predict phase separation on cooling.     

疏水改性智能水凝胶P(NIPA-co-DiAB)的合成及其温敏行为

以N-异丙基丙烯酰胺(NIPA)和N,N-双烯丙基苄胺(DiAB)为共聚单体、N,N-亚甲基双丙烯酰胺(BIS)为交联剂、十二烷基硫酸钠(SDS)为表面活性剂、过硫酸铵(APS)-四甲基乙二胺(TMEDA)为氧化还原引发体系,采用自由胶束交联共聚法合成了疏水基团为芳香基的疏水改性温敏性智能水凝胶P(NIPA-co-DiAB)。研究了DiAB摩尔分数(x(DiAB))对水凝胶溶胀性能的影响。 在初始溶胀阶段,随着x(DiAB)由0增大至3%,P(NIPA-co-DiAB)水凝胶的溶胀行为由Fickian扩散转变为non-Fickian扩散。x(DiAB)分别为0、1%、2%和3%时,P(NIPA-co-DiAB)水凝胶的平衡溶胀率SR0在蒸馏水中分别为63.6、93.5、141.6和167.4,在0.01 mol/L SDS溶液中分别为63.1、71.0、59.0和77.5,在CTAB溶液中分别为37.6、42.2、44.1和60.0,在Triton X-100溶液中分别为30.9、49.4、68.5和88.3。 结果表明,P(NIPA-co-DiAB)水凝胶的(SR0)大于PNIPA水凝胶,且在蒸馏中比在0.01 mol/L表面活性剂溶液中要大。 加入0.01 mol/L Triton X-100、CTAB或SDS后,PNIPA水凝胶的体积相变温度或较低临界溶解温度(LCST)由32.5 ℃分别增加至35.4、45.6和80 ℃。P(NIPA-co-DiAB)水凝胶的LCST由32.0～32.5 ℃分别增加至34.7～35.6 ℃、45.8~46.2 ℃和80 ℃。 加入表面活性剂能增加P(NIPA-co-DiAB)水凝胶的体积相变温度,高的体积相变温度与DiAB含量无关。     

光化学合成快速响应聚(N,N-二甲基丙烯酰胺-co-N-异丙基丙烯酰胺)水凝胶

通过光化学合成方法分别在高温(50℃)和室温(28℃)下实现了N,N-二甲基丙烯酰胺(DMAA)和N-异丙基丙烯酰胺(NIPAm)的交联共聚,制备了两种不同结构的P(DMAA-co-NIPAm)共聚物水凝胶.对两种温度下制备的P(DMAA-co-NIPAm)共聚物水凝胶的网络结构、溶胀与消溶胀速率和温度敏感性等方面进行了比较研究.结果发现,50℃下制备的P(DMAA-co-NIPAm)共聚物凝胶具有较为疏松的网络结构和相对较快的溶胀速率及温度响应特性.光化学合成方法较传统的热聚合制备方法具有简便、快捷的特点,合成过程仅需2 min.     

Specific thermoresponsive behaviours exhibited by optically active and inactive phenylalanine modified hyperbranched polyethylenimines in water

Optically active and inactive hyperbranched polymers with specific thermoresponsive behaviours in water were reported.Through two steps hyperbranched polyethylenimine (HPEI) polymers terminated with different amount of D-phenylalanine (D-Phe),L-phenylalanine (L-Phe) or DL-phenylalanine (DL-Phe) were prepared and characterized.The analyses on the solution properties by turbidimetry,dynamic light scattering,fluorescence probe and 1H-NMR demonstrated that all the polymers exhibited specific thermoresponsive behaviours in water,including:(1) In the dilute polymer concentration region,increasing the polymer concentration led to the increase of phase transition temperature;(2) The optically inactive thermoresponsive hyperbranched polymers showed a higher cloud-point temperature (Tcp) than their corresponding optically active ones in a relatively higher polymer concentration;(3) At the same polymer concentration the hydrophobic groups of the optically inactive HPEI-DL-Phe formed more perfect hydrophobic domain than those of the optically active HPEI-L-Phe and HPEI-D-Phe.     

腐植酸钠/聚丙烯酰胺/粘土杂化水凝胶的研究

以过硫酸钾为引发剂、N,N′-亚甲基双丙烯酰胺为交联剂、丙烯酰胺单体和腐植酸钠、Laponite RD粘土为原料,用溶液聚合交联法合成了腐植酸钠/聚丙烯酰胺/粘土(SH-PAM-Clay)系列水凝胶.用场发射扫描电镜对其表面形貌进行了研究,并对水凝胶的吸水性和流变性能进行了测试和研究.结果表明这系列水凝胶都具有致密的网络结构和优良的吸水性能.     

Effects of crosslinker density on the polymer network structure in poly‐N,N‐dimethylacrylamide hydrogels

To investigate the effects of crosslinker density on the properties of hydrogels, compression tests, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and Raman measurements were performed on poly‐N,N‐dimethylacrylamide hydrogels. The results of the compression tests showed that the Young's modulus increases as the crosslinker density increases. To understand the mechanism of the change in the mechanical properties, the structures of the polymer networks and water and the molecular vibrations were analyzed using SEM, DSC, and Raman methods. From the SEM images, it was found that the porosity estimated from the mesh size and cell density increases with increasing crosslinker density. In addition, the DSC and Raman results show that the thickness of the bound water increases as the porosity increases, although the density of the polymer chains in the porous wall remains nearly constant. The increase in the number density of polymer chains can be one of the mechanisms contributing to the increase in the mechanical strength of the hydrogels at lower crosslinker density below 5 mol %, as proposed by previous studies. At higher crosslinker density, however, the number density of polymer chains does not increase with increasing crosslinker density. The present results suggest that the bound water plays an important role in strengthening the hydrogel. The water structure may be one of the dominant factors governing the chemical and physical properties of hydrogels. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1017–1027     

States of water in poly(vinyl alcohol) hydrogels

Poly(vinyl alcohol) (PVA) hydrogels with various water contents were prepared from 10 wt% aqueous solutions of mixtures of PVA and anionic poly(styrene sulfonic acid) sodium salt (NaPSS) by casting, dehydrating, and then extracting NaPSS. The existence of three types of ice were suggested by differential scanning calorimetry (DSC) measurements for every frozen hydrogel. In the frozen hydrogels the states of water, except unfrozen water, were ice of free water and disordered ice crystals. The mobility and activation energy for motion of water molecules in unfrozen hydrogels were investigated by using pulsed nuclear magnetic resonance (PNMR) measurements. It was concluded that there are two states of water in the unfrozen hydrogel, i.e. unfrozen water and disordered water which is mainly formed in narrow apertures in the hydrogel. The discrepancy between the DSC and PNMR measurements was explained by a structural transformation during cooling.