A linear analysis of the effect of Faradaic currents on traveling-wave electroosmosis

Net fluid flow of electrolytic solutions induced by a traveling-wave potential applied to an array of co-planar interdigitated microelectrodes has been reported. At low applied voltages the flow is driven in the direction of the traveling-wave potential, as expected by linear and weakly nonlinear theoretical studies. The flow is driven at the surfaces of the electrodes by electrical forces acting in the diffuse electrical double layer. The pumping mechanism has been analyzed theoretically under the assumption of perfectly polarizable electrodes. Here we extend these studies to include the effect of Faradaic currents on the electroosmotic slip velocity generated at the electrode/electrolyte interface. We integrate the electrokinetic equations under the thin-double-layer and low-potential approximations. Finally, we analyze the pumping of electrolyte induced by a traveling-wave signal applied to a microelectrode array using this linear model.     

Diffusioosmosis of electrolyte solutions in a fine capillary slit

The steady diffusioosmotic flows of an electrolyte solution along a charged plane wall and in a capillary channel between two identical parallel charged plates generated by an imposed tangential concentration gradient are theoretically investigated. The plane walls may have either a constant surface potential or a constant surface charge density. The electrical double layers adjacent to the charged walls may have an arbitrary thickness and their electrostatic potential distributions are determined by the Poisson-Boltzmann equation. Solving a modified Navier-Stokes equation with the constraint of no net electric current arising from the cocurrent diffusion, electric migration, and diffusioosmotic convection of the electrolyte ions, the macroscopic electric field and the fluid velocity along the tangential direction induced by the imposed electrolyte concentration gradient are obtained semianalytically as a function of the lateral position in a self-consistent way. The direction of the diffusioosmotic flow relative to the concentration gradient is determined by the combination of the zeta potential (or surface charge density) of the wall, the properties of the electrolyte solution, and other relevant factors. For a given concentration gradient of an electrolyte along a plane wall, the magnitude of fluid velocity at a position in general increases with an increase in its electrokinetic distance from the wall, but there are exceptions. The effect of the lateral distribution of the induced tangential electric field and the relaxation effect in the double layer on the diffusioosmotic flow are found to be very significant.     

Microfluidic flow transducer based on the measurement of electrical admittance

A new flow transducer for measuring the flow rate of a conducting fluid in a microchannel is reported. In this paper, the measure of flow of such fluid under laminar flow conditions based on the change of electrical admittance is established with the aid of a pair of electrodes parallel to the line of flow in a glass-PDMS microfluidic device. This flow sensor is simple in design and can be integrated to most of the microfluidic platforms. The effect of flow rate of the electrolyte, the frequency of the applied ac voltage, the voltage applied across the detector electrodes, and the conductivity of the electrolyte are varied to optimize for high sensitivity. The optimized values are then used to demonstrate the measurements of very low flow rates (<1 nL s(-1)). This flow sensor can be extended towards the measurement of chemical and biochemical buffers and reagents.     

Electrokinetic flow in a capillary with a charge-regulating surface polymer layer

An analytical study of the steady electrokinetic flow in a long uniform capillary tube or slit is presented. The inside wall of the capillary is covered by a layer of adsorbed or covalently bound charge-regulating polymer in equilibrium with the ambient electrolyte solution. In this solvent-permeable and ion-penetrable surface polyelectrolyte layer, ionogenic functional groups and frictional segments are assumed to distribute at uniform densities. The electrical potential and space charge density distributions in the cross section of the capillary are obtained by solving the linearized Poisson-Boltzmann equation. The fluid velocity profile due to the application of an electric field and a pressure gradient through the capillary is obtained from the analytical solution of a modified Navier-Stokes/Brinkman equation. Explicit formulas for the electroosmotic velocity, the average fluid velocity and electric current density on the cross section, and the streaming potential in the capillary are also derived. The results demonstrate that the direction of the electroosmotic flow and the magnitudes of the fluid velocity and electric current density are dominated by the fixed charge density inside the surface polymer layer, which is determined by the regulation characteristics such as the dissociation equilibrium constants of the ionogenic functional groups in the surface layer and the concentration of the potential-determining ions in the bulk solution.     

Polymer electrolyte-gated organic field-effect transistors: low-voltage, high-current switches for organic electronics and testbeds for probing electrical transport at high charge carrier density

We report the fabrication and extensive characterization of solid polymer electrolyte-gated organic field-effect transistors (PEG-FETs) in which a polyethylene oxide (PEO) film containing a dissolved Li salt is used to modulate the hole conductivity of a polymer semiconductor. The large capacitance (approximately 10 microF/cm2) of the solution-processed polymer electrolyte gate dielectric facilitates polymer semiconductor conductivities on the order of 103 S/cm at low gate voltages (<3 V). In PEG-FETs based on regioregular poly(3-hexylthiophene), gate-induced hole densities were 2 x 10(14) charges/cm2 with mobilities >3 cm2/V.s. PEG-FETs fabricated with gate electrodes either aligned or intentionally nonaligned to the channel exhibited dramatically different electrical behavior when tested in vacuum or in air. Large differences in ionic diffusivity can explain the dominance of either electrostatic charging (in vacuum) or bulk electrochemical doping (in air) as the device operational mechanism. The use of a larger anion in the polymer electrolyte, bis(trifluoromethanesulfonyl)imide (TFSI-), yielded transistors that showed clear current saturation and square law behavior in the output characteristics, which also points to electrostatic (field-effect) charging. In addition, negative transconductances were observed using the PEO/LiTFSI electrolyte for all three polymer semiconductors at gate voltages larger than -3 V. Bias stress measurements performed with PEO/LiTFSI-gated bottom contact PEG-FETs showed that polymer semiconductors can sustain high ON currents for greater than 10 min without large losses in conductance. Collectively, the results indicate that PEG-FETs may serve as useful devices for high-current/low-voltage applications and as testbeds for probing electrical transport in polymer semiconductors at high charge density.     

Analytical study of Joule heating effects on electrokinetic transportation in capillary electrophoresis

Electric fields are often used to transport fluids (by electroosmosis) and separate charged samples (by electrophoresis) in microfluidic devices. However, there exists inevitable Joule heating when electric currents are passing through electrolyte solutions. Joule heating not only increases the fluid temperature, but also produces temperature gradients in cross-stream and axial directions. These temperature effects make fluid properties non-uniform, and hence alter the applied electric potential field and the flow field. The mass species transport is also influenced. In this paper we develop an analytical model to study Joule heating effects on the transport of heat, electricity, momentum and mass species in capillary-based electrophoresis. Close-form formulae are derived for the temperature, applied electrical potential, velocity, and pressure fields at steady state, and the transient concentration field as well. Also available are the compact formulae for the electric current and the volume flow rate through the capillary. It is shown that, due to the thermal end effect, sharp temperature drops appear close to capillary ends, where sharp rises of electric field are required to meet the current continuity. In order to satisfy the mass continuity, pressure gradients have to be induced along the capillary. The resultant curved fluid velocity profile and the increase of molecular diffusion both contribute to the dispersion of samples. However, Joule heating effects enhance the sample transport velocity, reducing the analysis time in capillary electrophoretic separations.     

Recent applications of AC electrokinetics in biomolecular analysis on microfluidic devices

AC electrokinetics is a generic term that refers to an induced motion of particles and fluids under nonuniform AC electric fields. The AC electric fields are formed by application of AC voltages to microelectrodes, which can be easily integrated into microfluidic devices by standard microfabrication techniques. Moreover, the magnitude of the motion is large enough to control the mass transfer on the devices. These advantages are attractive for biomolecular analysis on the microfluidic devices, in which the characteristics of small space and microfluidics have been mainly employed. In this review, I describe recent applications of AC electrokinetics in biomolecular analysis on microfluidic devices. The applications include fluid pumping and mixing by AC electrokinetic flow, and manipulation of biomolecules such as DNA and proteins by various AC electrokinetic techniques. Future prospects for highly functional biomolecular analysis on microfluidic devices with the aid of AC electrokinetics are also discussed.     

Frequency dependence of gold nanoparticle superassembly by dielectrophoresis

Dielectrophoresis is an effective method for capturing nanoparticles and assembling them into nanostructures. The frequency of the dielectrophoretic alternating current (ac) electric field greatly influences the morphology of resultant nanoparticle assemblies. In this study, frequency regimes associated with specific gold nanoparticle assembly morphologies were identified. Gold nanoparticles suspended in water were captured by microelectrodes at different electric field frequencies onto thin silicon nitride membranes. The resultant assemblies were examined by transmission electron microscopy. For this system, the major frequency-dependent influence on morphology appears to arise not from the Clausius-Mossotti factor of the dielectrophoretic force itself, but instead from ac electroosmotic fluid flow and the influence of the electrical double layer at the electrode-solution interface. Frequency regimes of technological interest include those forming one-dimensional nanoparticle chains, microwires, combinations of microwires and nanoparticle chains suitable for nanogap electrode formation, and dense three-dimensional assemblies with very high surface area.     

Fluid streaming above interdigitated electrodes in dielectrophoresis experiments

For the investigation of alternating current electrokinetic effects, a system is presented that allows for the simultaneous observation of fluid flow above and around microelectrodes in all three directions in space. Beside the usual microscopical view from top, lateral observation through the same objective is made possible by two small mirrors that are placed next to the electrodes. Fluid flow and movement of fluorescent nanoparticles above interdigitated electrodes are monitored by fluorescence microscopy and digital imaging and are further analysed by image processing. Field frequencies are varied from 10 Hz to 1 GHz at up to 10V(rms) . Electrical conductivity of the fluid is monitored in situ in the actual measuring chamber.     

A new method of evaluating the average electro-osmotic velocity in microchannels

A new and simple method to evaluate the average electro-osmotic flow velocity in microchannels is presented in this paper. In this method, the average electro-osmotic flow velocity is determined by using the slope of the measured current-time relationship during the electro-osmotic flow of one solution replacing another similar solution. The two solutions have the same electrolyte and a small difference in ionic concentration. Careful experiments were conducted to measure the electrical current change with time during such a displacing process under a constant applied electrical field. KCl and LaCl3 electrolyte solutions and 10-cm-long polyamide-coated silica capillary tubes of 100 and 200 microm in internal diameter were used in this study. The average velocities were determined by using the slope method. A numerical model was also developed to predict the average velocity of such an electro-osmotic flow. An excellent agreement in the average velocities between the slope method and the model predictions was found.     

Voltammetry Under Microfluidic Control,a Flow Cell Aproach

A generic approach to the design, construction and experimental characterization of novel microelectrochemical reactors (MECR) is presented. Structurally well‐defined rectangular microchannels incorporating electrochemical sensors were fabricated using a propriety photosensitive glass and photolithographic techniques. Microelectrode sensors were produced via evaporation to yield, gold, silver or platinum bands of approximate lengths 10–50 μm. The approach outlined permits cells of dimensions in the range: height 50–100 μm, width 100–500 μm and length 1–3 cm to be accurately constructed, in single or array configurations and were characterized via a voltammetric study utilizing electrolyte solutions containing N,N,N′N′‐Tetramethyl‐1,4‐phenylenediamine. In all cases, the test cells were constructed so that the three dimensional hydrodynamic boundary layer within the cells would significantly influence the reagent transport and therefore the observed current density at the microelectrodes. The current/flow rate relationship observed was analogous to the response of the observed within the macroscopic channel flow cells, where typically the cell design is restricted to configurations where a two dimensional transport analysis can be performed.     

Impedance measurements on a DNA junction

1 microm double-stranded DNA molecules are immobilized between pairs of gold and pairs of platinum microelectrodes with gaps of 0.4 and 1 microm, respectively, and their electrical characteristics are determined under the application of constant and sinusoidal bias voltages. Due to their extremely high impedance for constant voltage bias, the samples of DNA are excellent insulators; however, their impedances show strong frequency dependence in the range of 10 Hz-7.5 MHz. Favorable response in the gold electrodes is attributed to the higher ability of DNA molecules to bridge the narrower gold electrode gaps in contrast to that in the wider platinum junctions.     

Electrolytic Double-Layer Supercapacitors Based on Sodium-Ion Systems,with Activated-Carbon Electrodes

1 M solutions of NaClO₄ mixed with ethylene carbonate, dimethyl carbonate, and fluoroethylene carbonate were studied as electrolytes for a double-layer supercapacitor with electrodes made of Norit DLC Supra 30 activated carbon. It was shown that the specific capacity of activated carbon depends on the electrolyte composition, range of cycling voltages, and current density. The maximum specific capacitance of 40 F g^–1 was obtained in 1 M NaClO₄ mixed with ethylene carbonate: dimethyl carbonate: fluoroethylene carbonate (4: 5: 1) at a current density of 36 mA g^–1 in the range 10–2300 mV. The minimum specific capacitance was obtained under the same cycling conditions in the electrolyte with 1 M NaClO₄ + ethylene carbonate: dimethyl carbonate (1: 1). The variation of the specific capacitance with the electrolyte composition and range of cycling voltages is accounted for by the existence of a pseudocapacitance caused by the occurrence of side processes on the surface of activated carbon. The impedance spectroscopy was used to find that the introduction of fluoroethylene carbonate into the electrolyte positively affects the charge-transfer resistance and favors an increase in the specific capacitance of activated carbon.     

Computational electrochemo-fluid dynamics modeling in a uranium electrowinning cell

A computational electrochemo-fluid dynamics model has been developed to describe the electrowinning behavior in an electrolyte stream through a planar electrode cell system. Electrode reaction of the uranium electrowinning process from a molten-salt electrolyte stream was modeled to illustrate the details of the flow-assisted mass transport of ions to the cathode. This modeling approach makes it possible to represent variations of the convective diffusion limited current density by taking into account the concentration profile at the electrode surface as a function of the flow characteristics and applied current density in a commercially available computational fluid dynamics platform. It was possible to predict the conventional current–voltage relation in addition to details of electrolyte fluid dynamics and electrochemical variables, such as the flow field, species concentrations, potential, and current distributions throughout the galvanostatic electrolysis cell.     

Effect of ion pairing on steady-state voltammetric limiting currents at microelectrodes Part I. Theoretical principles

Voltammetric studies in solutions of high resistivity are facilitated by the use of microelectrodes under steady-state conditions. Such solutions are encountered with solvents of low permittivity because of the very sparing solubility of electrolytes. Moreover, in such media the supporting electrolyte, as well as the electroactive ionic species, is usually extensively ion paired. Here we predict the limiting current that will flow in these circumstances, when a monovalent ion undergoes a one-electron transfer at a hemispherical microelectrode to form a neutral product. The ion pairing equilibria are assumed to be fast but all diffusion coefficients are treated as distinct. An analytical solution is elusive in the general case, but a simple numerical procedure allows the limiting current to be predicted for any combination of the system parameters. Several special cases are also discussed, some of which yield explicit formulae for the limiting current. In a companion paper, experimental data are compared with the theoretical predictions.     

AgI-Ag2O-V2O5 glasses as ion-to-electron transducers for the construction of all-solid-state microelectrodes

A method for the fabrication of ion-selective all-solid-state microelectrodes is presented. The ion-to-electron transduction process takes place into the transducer material. In this approach, AgI-Ag₂O-V₂O₅ glasses, which exhibit ionic and electrical conductivity are applied as ion-to-electron transducers of polymeric membrane microelectrodes. All-solid-state electrodes based on potassium-sensitive poly(vinyl chloride) membranes, deposited directly on the surface of glass composites, exhibited theoretical responses. Their selectivity and durability were comparable to planar microelectrodes containing an internal electrolyte immobilized in the intermediate hydrogel layer. The only disadvantage of the proposed structures was their limited reproducibility. Moreover, it was found that the unmodified AgI-Ag₂O-V₂O₅ glasses can be applied as ion-sensitive membrane of solid-state microelectrodes for the determination of Ag⁺ and I⁻ ions.     

液态Wood合金在NaOH电解质溶液中的电毛细变形现象

本文研究了液态Wood合金在氢氧化钠电解质溶液中,通过施加外电场,进而诱发液态金属电毛细变形的现象. 当石墨电极伸入金属液滴内部时,通电后在金属表面发生的电极反应,促使金属表面形成氧化膜或去除氧化膜. 由于氧化膜与液态金属的表面张力存在巨大差异,通电后电极极性的变化可实现金属液滴形状的快速可逆变形.在液态金属与电解质溶液之间形成的双电子层中,当两侧聚集同极性电荷时将降低界面张力.为维持通电后体系自由能最小,将迫使液体金属增大与溶液之间的界面面积,在宏观上表现为液体金属的变形,由于液态金属与氢氧化钠反应后自身携带负电荷,在电场力的作用下可有效地驱动液态金属在电解质溶液中的运动.     

Polyimide-based microfluidic devices

This paper describes the development of polyimide-based microfluidic devices. A layer transfer and lamination technique is used to fabricate flexible microfluidic channels in various shapes and with a wide range of dimensions. High bond strengths can be achieved by cure cycle adaptation and surface treatment of the polyimide layers prior to bonding. The polyimide microchannels can be combined with metallization layers to fabricate electrodes inside and outside channels. The resulting devices can be used for flexible fluidic and electrical connectors, implantable fluid delivery devices, microelectrodes with embedded fluidic channels, chip-based flow cytometry and for a great variety of other applications in medical, chemical or biological research.     

Membrane potential in charged porous membranes

For charged porous membranes, the separation efficiency to charged particles and ions is affected by the electrical properties of the membrane surface. Such properties are most commonly quantified in terms of zeta-potential. In this paper, it is shown that the zeta-potential can be calculated numerically from the membrane potential. The membrane potential expression for charged capillary membranes in contact with electrolyte solutions at different concentrations is established by applying the theory of non-equilibrium thermodynamic to the membrane process and considering the space-charge model. This model uses the Nernst–Planck and Navier–Stokes equations for transport through pores, and the non-linear Poisson–Boltzmann equation, which is numerically solved, for the electrostatic condition of the fluid inside pores. The integral expressions of the phenomenological coefficients coupling the differential flow (solute relative to solvent) and the electrical current with the osmotic pressure and the electrical potential gradients are established and calculated numerically. The mobilities of anions and cations are individually specified. The variations of the membrane potential (or the apparent transport number of ions in the membrane pores) are studied as a function of different parameters: zeta-potential, pore radius, mean concentration in the membrane, ratio of external concentrations and type of ions.