ZnMgO/ZnO异质结构中二维电子气的研究

论文根据ZnMgO/ZnO异质结构二维电子气的能带结构及相关理论模型, 采用一维Poisson-Schrodinger方程的自洽求解, 模拟计算了ZnMgO/ZnO异质结构中二维电子气的分布及其对ZnMgO势垒层厚度及Mg组分的依赖关系. 研究发现该异质结构中ZnMgO势垒层厚度存在一最小临界值: 当垒层厚度小于该临界值时, 二维电子气消失, 当垒层厚度大于该临界值时, 其二维电子气密度随着该垒层厚度的增加而增大; 同时研究发现ZnMgO势垒层中Mg组分的增加将显著增强其二维电子气的行为, 导致二维电子气密度的明显增大; 论文对模拟计算获得的结果与相关文献报道的实验结果进行了比较, 并从极化效应和能带结构的角度进行了分析和讨论, 给出了合理的解释. 关键词： 氧化锌 二维电子气 异质结构 理论计算     

Synthesis and optical properties of flower-like ZnO nanorods by thermal evaporation method

Flower-like ZnO nanorods have been synthesized by heating a mixture of ZnO/graphite powders using the thermal evaporation and vapor transport on Si (1 0 0) substrates without any catalyst. The structures, morphologies and optical properties of the products were characterized in detail by using X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), photoluminescence (PL) and Raman spectroscopy. The synthesized products consisted of large quantities of flower-like ZnO nanostructures in the form of uniform nanorods. The flower-like ZnO nanorods had high purity and well crystallized wurtzite structure, whose high crystalline quality was proved by Raman spectroscopy. The as-synthesized flower-like ZnO nanorods showed a strong ultraviolet emission at 386 nm and a weak and broad yellow-green emission in visible spectrum in its room temperature photoluminescence (PL) spectrum. In addition, the growth mechanism of the flower-like ZnO nanorods was discussed based on the reaction conditions.     

ZnMgO生长中压强和衬底对薄膜性质的影响

利用金属有机源化学气相沉积(MOCVD)生长方法,在2.5 kPa和5 kPa生长压强下,分别以sapphire (Al2O3)和ZnO为衬底生长ZnMgO薄膜.研究分析了样品的晶体结构、表面形貌、光电学性质.结果表明,衬底和生长压强对ZnMgO薄膜的生长有重要影响.5 kPa高压生长和以ZnO为衬底均有利于ZnMgO...     

Effect of the reaction conditions on the formation of the ZnO nanostructures

ZnO nanorods were synthesized through a simple chemical method by reacting Zn(C₂H₃O₂)₂·2H₂O and NaOH at low temperature and the effects of changing the order of addition of reactants on the morphological evolution of ZnO nanorods were investigated. The samples were characterized by using XRD, SEM, EDX, TEM, BET and Raman techniques. Optical properties of the ZnO nanostructures were too investigated by UV–Vis spectroscopy at room temperature.The hexagonal wurtzite phase of ZnO was confirmed by X-ray diffraction (XRD) for all the samples. SEM and TEM analysis indicated that different morphologies were obtained by changing the order of addition of reactants.     

Effects of electrolyte on ZnO nanostructures synthesized by galvanostatic electrochemical deposition and their UV sensing properties

In this study, ZnO nanorods (NRs) and nanocombs (NCs) are synthesized by simple galvanostatic electrochemical deposition technique, without prepared any ZnO seed-layer or catalyst. The effect of the different morphologies on the UV sensing characteristics has been studied under ambient conditions. The photoluminescence (PL) spectra and time-dependent photoresponse of the ZnO nanostructures exhibited good optical properties. At room temperature, NCs showed superior response with 9% change of its resistance, few seconds response time and fully recovery. Inversely, in high temperature ZnO NRs indicated better response than NCs with the variation of 25% of its resistance. The dependence photoresponse on temperature demonstrated clearly how surface-defects affect on UV response of ZnO nanostructures. Our approach is to provide a simple and cost-effective way to fabricate UV detectors.     

Low temperature synthesis of hexagonal ZnO nanorods and their hydrogen sensing properties

The growth of hexagonal ZnO nanorods was demonstrated by low temperature chemical synthesis approach. X-ray diffraction (XRD) analysis revealed a wurtzite hexagonal structure of the ZnO nanorods. The optical properties were measured by UV-vis spectrophotometer at room temperature. X-ray photoelectron spectroscopy (XPS) confirmed high purity of the ZnO nanorods. The hydrogen sensor made of the ZnO nanorods showed reversible response. The hydrogen gas tests were carried out in presence of ambient air and the influence of operation temperature on the hydrogen gas sensing property of ZnO nanorods was also investigated.     

Synthesis and photoluminescence properties of ZnO nanorods and nanotubes

Different morphologies of zinc oxide (ZnO) nanorods and nanotubes, which were grown under the same conditions but different dissolving processes, are prepared in our experiment through hydrothermal method. After the growth process, cooling down the reactor naturally or dissolving at a constant temperature of 40 °C, preferential dissolution will occur at different places on the tip of ZnO nanorods. During the dissolution process, different dissolution rates on the entire surface of nanorod will lead to different nanostructures. ZnO nanorods and nanotubes on Cu substrates display the same PL property with strong green emission but weak UV emission, while ZnO nanorods on Si substrates exhibits a relatively strong UV emission.     

ZnMgO/n-ZnO/ZnMgO/p-GaN异质结LED的紫外电致发光

利用等离子体辅助分子束外延( P-MBE)技术制备了ZnMgO/n-ZnO/ZnMgO/p-GaN异质结LED.Ni/Au电极与p-GaN、In电极与ZnMgO之间都形成了良好的欧姆接触.在ZnMgO/n-ZnO/ZnMgO/p-GaN异质结器件中观察到了明显的整流特性.异质结的电致发光强度随着注入电流的增大而逐渐增强...     

Morphological transition of ZnO nanostructures influenced by magnesium doping

Wurtzite zinc oxide (ZnO) nanochains have been synthesized through high-pressure pulsed laser deposition. The chain-like ZnO nanostructures were obtained from magnesium (Mg) doped ZnO targets, whereas vertically aligned nanorods were obtained from primitive ZnO targets. The Mg doping has influenced the morphological transition of ZnO nanostructures from nanorods to nanochains. The field emission scanning electron microscope images revealed the growth of beaded ZnO nanochains. The ZnO nanochains of different diameters 40 and 120 nm were obtained. The corresponding micro-Raman spectra showed strong E_2H mode of ZnO, which confirmed the good crystallinity of the nanochains. In addition to near band edge emission at 3.28 eV, ZnO nanochains show broad deep level emission at 2.42 eV than that of ZnO nanorods.     

Aqueous chemical growth of free standing vertical ZnO nanoprisms,nanorods and nanodiskettes with improved texture co-efficient and tunable size uniformity

Tuning the morphology, size and aspect ratio of free standing ZnO nanostructured arrays by a simple hydrothermal method is reported. Pre-coated ZnO seed layers of two different thicknesses (≈350 nm or 550 nm) were used as substrates to grow ZnO nanostructures for the study. Various parameters such as chemical ambience, pH of the solution, strength of the Zn²⁺ atoms and thickness of seed bed are varied to analyze their effects on the resultant ZnO nanostructures. Vertically oriented hexagonal nanorods, multi-angular nanorods, hexagonal diskette and popcorn-like nanostructures are obtained by altering the experimental parameters. All the produced nanostructures were analysed by X-ray powder diffraction analysis and found to be grown in the (002) orientation of wurtzite ZnO. The texture co-efficient of ZnO layer was improved by combining a thick seed layer with higher cationic strength. Surface morphological studies reveal various nanostructures such as nanorods, diskettes and popcorn-like structures based on various preparation conditions. The optical property of the closest packed nanorods array was recorded by UV-VIS spectrometry, and the band gap value simulated from the results reflect the near characteristic band gap of ZnO. The surface roughness profile taken from the Atomic Force Microscopy reveals a roughness of less than 320 nm.     

水浴法制备ZnO纳米棒及其场发射性能

用硝酸锌(Zn(NO3)2·6H2O)与六亚甲基四胺(C6H12N4)以等浓度配制成反应溶液,通过水浴法制备出了形貌可控的棒状ZnO纳米结构,讨论了不同反应浓度及衬底对ZnO表面形貌的影响.样品的XRD和扫描电子显微镜分析结果表明,所得产物均为六方纤锌矿结构,在有晶种层的衬底上制备出的ZnO纳米棒沿(001)方向并垂直于衬底表面生长.随着反应浓度的增加,ZnO纳米棒的直径增大,长径比减小.样品的场发射性能测试表明,反应溶液浓度为0.005 mol/L,以铜膜为晶种层的硅衬底上制备出的场发射阴极具有较好的场发射性能.     

Effect of substrates and anions of zinc salts on the morphology of ZnO nanostructures

The ZnO nanostructures were hydrothermally synthesized on glass and Al substrates, respectively, using zinc chloride, zinc nitrate, and zinc acetate as precursor. The as-prepared products were characterized by scanning electron microscopy (SEM) and X-ray powder diffraction (XRD). Different ZnO nanostructures were obtained, such as nanorods, nanosheets, flower-like nanostructures and so on. The effects of the substrates and anions of zinc salts on the morphologies of the resulting products have been investigated.     

聚乙烯亚胺对氧化锌纳米阵列形貌的影响

采用化学沉淀法,以硝酸锌和六次亚甲基四胺的水溶液为生长溶液,在涂覆氧化锌晶种层的玻璃衬底上制备了定向生长的氧化锌纳米棒阵列,并研究了添加剂聚乙烯亚胺的浓度对氧化锌纳米棒形貌和结构的影响。X射线衍射和场发射扫描电镜的结果表明,合成的氧化锌纳米棒阵列较为均匀致密,具有六方纤锌矿结构,且有沿(002)晶面择优生长的特性;随着聚乙烯亚胺浓度的增加,氧化锌纳米棒的直径减小,直径分布趋于均匀,且氧化锌纳米棒的形貌也从锥状转变为柱状结构;另外,聚乙烯亚胺的加入对氧化锌的生长速度具有抑制作用,当聚乙烯亚胺的浓度增加至0.012 mol·L-1时,无氧化锌阵列生长。对氧化锌纳米棒阵列进行了拉曼光谱表征,结果表明,随着溶液中聚乙烯亚胺浓度的增加,氧化锌纳米棒的氧空位缺陷减少。最后,对聚乙烯亚胺浓度对氧化锌纳米阵列影响的机理进行了探讨。     

Controlling the orientation of ZnO nanorod arrays using TiO<Subscript>2</Subscript> thin film templates dip-coated by sol–gel

The oriented ZnO nanorod arrays have been synthesized on a silicon wafer that coated with TiO₂ films by aqueous chemical method. The morphologies, phase structure and the photoluminescence (PL) properties of the as-obtained product were investigated by field-emission scanning electron microscopy (FE-SEM), X-ray diffractometer (XRD), transmission electron microscope (TEM) and PL spectrum. The nanorods were about 100 nm in diameter and more than 1 μm in length, which possessed wurtzite structure with a c axis growth direction. The room-temperature PL measurement of the nanorod arrays showed strong ultraviolet emission. The effect of the crystal structure and the thickness of TiO₂ films on the morphologies of ZnO nanostructures were investigated. It was found that the rutile TiO₂ films were appropriate to the oriented growth of ZnO nanorod arrays in comparison with anatase TiO₂ films. Moreover, flakelike ZnO nanostructures were obtained with increasing the thickness of anatase TiO₂ films.     

Effect of substrate temperature on the growth and luminescence properties of ZnO nanostructures

ZnO nanowires, nanorods and nanoribbons have been prepared by heating a mixture of ZnO/graphite powders using the thermal evaporation and vapor transport on Si(1 0 0) substrates without any catalyst. The nanostructures are grown as a function of substrate temperature ranging from 900 to 1300 K. These nanostructures are of the size 100–300 nm in diameter or width and several tens of micrometers in length. We studied the influence of the substrate temperature on the luminescent properties of these nanostructures. We observed a strong relationship between the substrate temperature and the green emission band in ZnO, i.e., the photoluminescence study revealed that the green emission peak of the ZnO nanostructures is suppressed relative to the band edge emission when the substrate temperature is decreased from 1300 to 900 K.     

Growth and optical study of ZnO nanorods

ZnO nanorods were grown by a simple near room temperature, chemical solution method on ZnO-seeded silicon substrates. Study of the ZnO nanorods over different growth times by electron microscopy methods revealed that the resulting ZnO nanorods were single crystalline with a highly preferential growth perpendicular to the substrate and a very good c-axis alignment. The size of the nanorods increased with increasing growth time. The growth mechanism is briefly discussed. Post-annealing in oxygen slightly improved the surface roughness of the ZnO nanorods. Photoluminescence experiments at 1.6 K revealed a major emission peak of the nanorods at around 3.36 eV which is attributed to the band edge transition of ZnO, while defect-related emission is relatively weak.     

Fabrication of ZnO nanostructures of various dimensions using patterned substrates

ZnO nanostructures were grown on silicon, porous silicon, ZnO/Si and AlN/Si substrates by low-temperature aqueous synthesis method. The shape of nanostructures greatly depends on the underlying surface. Scattered ZnO nanorods were observed on silicon substrate, whereas aligned ZnO nanowires were obtained by introducing sputtered ZnO film as a seed layer. Furthermore, both the combination of nanorods and the bunch of nanowires were found on porous silicon substrates, whereas platelet-like morphology was observed on AlN/Si substrates. XRD patterns suggest the crystalline nature of aqueous-grown ZnO nanostructures and high-resolution transmission electron microscopy images confirm the single-crystalline growth of the ZnO nanorods along [0 0 1] direction. Room-temperature photoluminescence characterization clearly shows a band-edge luminescence along with a visible luminescence in the yellow spectral range.     

Growth and properties of ZnO nanorod and nanonails by thermal evaporation

ZnO nanorods and nanonails have been synthesized on silicon wafers by a three-step catalyst-free thermal evaporation method in oxygen atmosphere. All the samples were hexagonal phase ZnO with highly c-axis preferential orientation. Different morphologies of ZnO nanostructures, i.e. ZnO nanorods and two kinds of nanonails, were observed at various temperature regions. Photoluminescence, transmission electron microscopy, and energy-dispersive X-ray spectroscope were employed to elucidate the reason for the formation of such different rod-like structures. The analysis results demonstrated that the caps of nanonails possess a large number of oxygen vacancies, which may play a key role in determining the formation of nanonails and the high intensity of green emission.     

Highly efficient and low turn-on voltage quantum-dot light-emitting diodes using a ZnMgO/ZnO double electron transport layer

A ZnMgO and ZnO double-layered structure was prepared to create a stepwise interfacial electronic structure to improve the electron-injection and electron-transport behaviors in quantum-dot light-emitting diodes (QLEDs). The current density of the electron-only device (EOD) with ZnMgO/ZnO was higher than that of the EOD with only ZnMgO. The detailed QLED interfacial electronic structure was measured using X-ray and ultraviolet photoelectron spectroscopy. A stepwise interfacial electronic structure for electron injection and electron transport was observed connecting the aluminum cathode to the ZnMgO conduction band minimum (CBM) via the ZnO CBM. The QLEDs with the ZnMgO/ZnO double electron transport layer showed an improved performance, with a maximum luminance and current efficiency of 90,892 cd m⁻² and 19.2 cd A⁻¹, respectively. Moreover, the turn-on voltage of the device was significantly reduced to 2.6 V due to the stepwise interfacial electronic structure between the aluminum cathode and ZnMgO CBM. This research provides a useful method for developing highly efficient and low turn-on voltage QLEDs using a ZnMgO/ZnO double ETL for next-generation display.     

Investigation of the luminescence properties of ZnO tetrapods and clusters grown on Si substrates

ZnO nanostructures are formed on Si substrates using Zn powder without catalyst. The substrate temperature was controlled from 450 to 600 °C, and the variation of structural and optical properties was investigated. From all samples both ZnO tetrapods and clusters were observed. Among them, no significant dispersion was observed from the ZnO tetrapods. However, ZnO clusters show considerable change in density and size. From the energy dispersive X-ray spectroscopy (EDX) results, atomic composition difference was observed. The clusters have considerable O-deficiencies, while tetrapods have almost stoichiometric composition. From all samples, strong luminescence, UV emission at 3.21 eV and green emission at 2.5 eV, were observed at room temperature. Cathodoluminescence measurements showed that the UV emission is closely related with tetrapods and the green emission is dominated from the clusters.