InCl3-catalyzed efficient one-pot synthesis of 2-pyrrolo-3′-yloxindoles

An InCl₃-catalyzed one-pot synthesis of 2-pyrrolo-3′-yloxindoles was achieved via three-component reaction of 3-phenacylideneoxindole, β-keto ester, and ammonium acetate at reflux by a sequential Michael addition followed by Paal-Knorr condensation.     

Effect of different dispersing agents in the non-isothermal kinetics and thermomechanical behavior of PET/TiO2 composites

This work is based on the analysis of the influence of dispersing agents on the non-isothermal kinetics, thermomechanical behavior and dispersing action of PET/TiO₂ nanocomposites. The influence of two montanic waxes and an amide wax used as dispersing agents in the nucleating effect of the nanoparticles is studied. The dispersing agents are the following: a) a partly saponified ester of montanic acids (PSEMA), b) an ester of montanic acids with multifunctional alcohols (MAWMA) and c) an amide wax based on N,N′-Bisstearoyl ethylenediamine (AW). The non-isothermal kinetics based on the Avrami method revealed that MAWMA and PSEMA favors the nucleating effect of the nanoparticles when are included in PET. Birefringence microscopy points out the good dispersing capacity of MAWMA and AW and the termomechanical analysis confirmed that the ester of montanic acids with multifunctional alcohols MAWMA shows the best dispersing properties and best promotes the nucleating effect of the TiO₂ nanoparticles when used for PET/TiO₂ nanocomposites production.     

Synthesis of Ethyl Nicotinate-5-Boronic Acid Pinacol Ester and Its Application Toward Suzuki Coupling

A method for the synthesis and isolation of pure ethyl nicotinate-5-boronic acid pinacol ester has been described. This boronate ester was used to prepare C₂-C₅ heteroarylnicotinates in good yields.     

Hydrophobic Vitamin B12. X. Steric Effect in Electrochemical Carbon-Skeleton Rearrangement Catalyzed by Hydrophobic Vitamin B12 in Nonaqueous Media

Abstract

A steric effect in the carbon-skeleton rearrangement catalyzed by heptamethyl cobyrinate perchlorate, [Cob(II)7C₁ester]C10₄, was investigated under electrochemical conditions. The controlled-potential electrolyses of alkyl halides having two carboxylic ester groups of different bulkiness on the same carbon atom, such as 2,2-bis(ethoxycarbonyl)-l-bromopropane, l-bromo-2-tert-butoxycarbonyl-2-ethoxy-carbonylpropane, l-bromo-2-cyclohexyloxycarbonyl-2-ethoxycarbonylpropane, and l-bromo-2-ethoxy-carbonyl-2-phenoxycarbonylpropane, were carried out in N,N-dimethylformamide, as catalyzed by [Cob(II)7C₁ester]CIO₄, to give the corresponding ester-migrated products in the dark at—1.5 V vs SCE in the presence of acetic acid and at—2.0 V vs SCE without acetic acid. As regards a correlation between bulkiness of an ester group and a migration aptitude, a smaller ester group tends to migrate to the adjacent carbon atom more readily than a larger one. The origin of such a steric effect is discussed with attention to the rate-determining step.     

Synthesis of Derivatives of Chlorin P6 Trimethyl Ester

The Vilsmeier reaction of nickel(II) chlorin P₆ trimethyl ester with 3-dimethyl-aminoacrolein yielded nickel(II) chlorin P₆ 20-(2-formylvinyl) trimethyl ester and nickel(II) chlorin P₆ 3-(1-hydroxyethyl)-3-devinyl-20-(2-formylvinyl) trimethyl ester. Also, the outgrowths of nickel(II) chlorin P₆ 20-(2-formyl) trimethyl ester and nickel(II) chlorin P₆ 3-(2-formylvinyl)-3-devinyl-20-(2-formyl) trimethyl ester were obtained by Vilsmeier reaction with dimethylformamide. By treating the derivatives of nickel(II) 20-(2-formyl)-chlorin and nickel(II) 3-(2-formylvinyl)-20-(2-formyl)-chlorin with trifluoracetic acid, the removal of the central nickel(II) ion was accomplished. The derivatives of 20-(2-formyl)-chlorin and 3-(2-formylvinyl)-20-(2-formyl)-chlorin demonstrated considerable bathochromic shift of the major absorption band in the red region of the optical spectrum.     

Comparative study of the synthesis of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> and NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript> in silica through the polymerized complex route of the sol–gel method

In this work the synthesis of CoFe₂O₄-SiO₂ and NiFe₂O₄-SiO₂ nanocomposites was studied via the sol–gel method, using the polymerized complex route. The polymerized precursors obtained by the reaction of citric acid, ethylene glycol, tetraethylorthosilicate, ferric nitrate, and cobalt nitrate or nickel chloride were characterized by nuclear magnetic resonance (NMR) and infrared (IR) spectroscopy. NMR and IR spectra of the precursors, without and with metallic ions, show the formation of polymeric chains with ester and ether groups and complexes of metal-polymeric precursor. The nanocomposites were obtained by the thermal decomposition of the organic fraction and characterized by X-ray diffraction (XRD) and vibrating sample magnetometry (VSM). XRD patterns show the formation of CoFe₂O₄ and NiFe₂O₄ in an amorphous silica matrix above 400 °C in both cases. When the calcination temperature was 800 °C the particle size of the crystalline phases, calculated using the Scherrer equation, reached ∼35 nm for the two oxides. VSM plots show the ferrimagnetic behavior that is expected for this type of magnetic material; the magnetization at 12.5 KOe of the CoFe₂O₄-SiO₂ and NiFe₂O₄-SiO₂ compounds was 29.5 and 17.4 emu/g, respectively, for samples treated at 800 °C.     

Synthesis of 1-fluoroindan-1-carboxylic acid (FICA) and its properties as a chiral derivatizing agent

1-Fluoroindan-1-carboxylic acid (FICA) (1) was designed and synthesized as its methyl ester (FICA Me ester) (4) in order to develop an efficient chiral derivatizing agent (CDA) which excels α-methoxy-α-(trifluoromethyl)phenylacetic acid (MTPA) in capability. FICA Me ester (4) was prepared by fluorination of methyl 1-hydroxyindan-1-carboxylate (3) with (diethylamino)sulfur trifluoride (DAST) and derived to the esters of racemic secondary alcohols by ester exchange reaction. The resulting Δδ_F value was large in the case of 2-butyl ester of FICA (5a), whereas not detectable in the case of the corresponding MTPA ester (6a). The magnitude of the Δδ_H values was similar to that of MTPA esters. The diastereomers of (R)-(−)-8-phenylmenthyl ester of FICA (5i) was separated and their ¹H NMR analyses revealed that the concept of the modified Mosher's method was successfully applied to 5i.     

An expedient synthesis of indolo[1,2-a]quinolines via Mn(OAc)3-mediated oxidative free radical cyclization and NaI/O2-assisted dealkoxycarbonylation/aerobic oxidation cascade

An expedient synthetic procedure of indolo[1,2-a]quinolines was developed using a sequential Cu-mediated N-arylation of indole, Mn(OAc)₃-mediated oxidative free radical cyclization, and NaI/O₂-assisted concomitant dealkoxycarbonylation/aerobic oxidation. The last step was replaced by a palladium-catalyzed decarboxylation/elimination protocol for the allyl ester derivatives.     

Thermal decomposition of Me3SnO2PCl2, Me2Sn(O2PCl2)2 and Ph3SnO2PCl2

TG and DTA studies on Me₃SnO₂PCl₂, Me₂Sn(O₂PCl₂)₂ and Ph₃SnO₂PCl₂ were carried out under dynamic argon atmosphere. The results show that the decomposition proceeds in different stages leading to the formation of Sn₃(PO₄)₂ as a stable product. This compound was characterized by IR spectroscopy. Decomposition schemes involving reductive elimination reactions were proposed.     

The role of precursors in the structure of SiO2-Al2O3 sols and gels by the sol-gel process

Binary sols and gels of SiO₂-Al₂O₃ were prepared using tetraethyl orthosilicate and each of four aluminum compounds; aluminum di (sec-butoxide) ethylacetoacetic ester chelate (AC), aluminum nitrate nonahydrate (AN), aluminum formoacetate (AF), and boehmite sol (BS) made from aluminum i-propoxide. The structure and the evolution of the Si-O-Al bonds in SiO₂-Al₂O₃ sols and gels were investigated by ²⁷Al nuclear magnetic resonance (NMR), Infrared absorption spectra, DTA, and X-ray diffraction. The formation of Si-O-Al bonds differs depending on the aluminum compounds used as raw materials. The ratio of Al(IV) to {Al(IV) + Al(VI)} is related to the microstructural homogeneity of the gels. When AC is used as a raw material, the Si-O-Al bonds are formed in the sol state and resultant gel shows good microstructural homogeneity. In case of AN, the Si-O-Al bonds are not formed either in the sol or the wet gel state. The bonds are formed by drying the gel before heat-treatment temperature reaches 300 400°C, resulting in good microstructural homogeneous gel. When AF is used, the Si-O-Al bonds are formed in the sol state but the ratio of Al(IV) to {Al(IV) + Al(VI)} is lower than when using AC. Microstructural homogeneity of the gel is ranked between AC or AN and BS. Using BS, the Si-O-Al bonds are not formed in the sol solution, and the change in the coordination number of the gel is similar to that of boehmite gel. The Microstructural homogeneity of the gel is the worst among the BS gels, which were prepared by using the four aluminum raw materials.     

The catalytic role of oxide in the thermooxidative degradation of poly(methyl methacrylate)-TiO2 nanocomposites

The influence of TiO₂ nanoparticles on the thermal degradation of poly(methyl methacrylate) (PMMA) was investigated by TGA. The studied materials were characterized by Py-GC-MS, TEM, SEM, TGA, DSC and TGA-MS. The PMMA-TiO₂ nanocomposites were prepared by melt blending with different (5, 10, 15 and 20 wt% TiO₂) loadings. According to TGA results and to the activation energy (determined by the model-free isoconversional method of Vyazovkin), the incorporation of 5 wt% of TiO₂ nanoparticles into PMMA stabilizes it by more than 40 °C. However, for higher loading contents, a catalytic effect on the thermal decomposition was observed which increased with the oxide content. The results obtained by Py-GC-MS showed clearly that TiO₂ increases the formation of methanol, methacrylic acid and propanoic acid methyl ester during the degradation of PMMA. This catalytic effect could be explained through the interaction of the methoxy group of the methacrylate function with the hydroxyl groups present at the surface of the oxide particles.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

Synthesis and thermal investigation of Na2Cd(SO4)2·2H2O

The synthesis and thermal decomposition of Na₂(SO₄)₂·2H₂O in both air and nitrogen are described. The synthesis was performed by two different procedures, but in both cases the same product was obtained, corresponding to the general formula given above. The crystals obtained were investigated by methods of X-ray powder diffraction, and chemical and thermal analysis. The differences in thermal decomposition in air and nitrogen are discussed.     

Synthesis and optical behaviour of monodispersed oligo(fluorenylidene)s

The synthesis of the first series of monodispersed oligo(fluorenylidene)s is reported. The synthetic sequence envisages as key steps the obtainment (a) of a bis-pinacolboronate fluorenylidene dimer by a Ni(cod)₂ promoted homocoupling of the suitable 7-bromo-fluorenylidene boronic ester and (b) of the bis-pinacolboronate fluorenylidene trimer and tetramer by a Ni(cod)₂ promoted coupling of a 7-bromo-fluorenylidene boronic ester with 0.5 equiv of the corresponding 2,7-dibromofluorenylidene derivative. The optical properties of the obtained oligomers were studied. In the case of OF3 the optical behaviour was compared to that of a suitably synthesized fluorenone-containing model compound.     

Experimental determination and calculation of the critical curves for the binary systems of CO2 containing ketone, alkane, ester and alcohol, respectively

A set of variable-volume autoclave with a quartz window was used for the experimental determination of the high-pressure phase equilibria and critical curves. The critical temperatures, pressures, densities and mole volumes in the region near the critical point of CO₂ were examined for eleven binary systems of supercritical CO₂ (SC CO₂) with different kinds of substances (ketone, alkane, ester and alcohol), respectively. The critical curves of the above binary systems were also calculated using an equation of state. The equation consists of a hard body repulsion term and an additive perturbation term, which takes care of the attractive molecular interaction. The calculated data were compared with the experimental data, and yielded good agreements. At the same time, the values of the adjustable parameters, λ, k_σ and k_? were obtained. The critical curves of the above eleven binary systems at higher temperatures and pressures all belong to type I.     

Synthesis of Novel New 2-(2-(4-((3,4-Dihydro-4-oxo-3-aryl quinazolin-2-yl)methyl)piperazin-1-yl)acetoyloxy)-2-phenyl Acetic Acid Esters

Stereoselective diazotization of (S)-2-amino-2-phenyl acetic acid (L-phenyl glycine) (4) with NaNO₂ in 6% H₂SO₄ in a mixture of acetone and water gave optically pure (S)-2-hydroxy-2-phenyl acetic acid (L-mandelic acid) (5). Esterification, gave (S)-2-hydroxy-2-phenyl acetic acid esters (6). The latter was treated with chloroacetyl chloride in the presence of triethylamine (TEA) in dichloromethane (DCM) to yield (S)-2-chloroacetyloxy phenyl acetic acid ester (2). In another sequence, the reaction of 2-(chloromethyl)-3-arylquinazolin-4(3H)-one (9) treated with N-Boc piperazine, followed by deprotection of the Boc group, to obtain 3-aryl-2-((piperazin-1-yl)methyl) quinazolin-4(3H)-one (3). Reaction of 2 with 3 in the presence of K₂CO₃ and KI gave the title compound, 2-(2-(4-((3,4-dihydro-4-oxo-3-arylquinazolin-2-yl)methyl)piperazin-1-yl) acetoyloxy)-2-phenyl acetic acid esters (1). The structures of all the new compounds obtained in the present work are supported by spectral and analytical data.     

CRTA Study of the Reduction of UO2F2 into UO2 by Dry H2

The reduction of UO₂F₂ by dry H₂ was studied by Controlled Rate EGA, with a special set-up operating under a gas flow under atmospheric pressure. At the constant transformation rate selected, this reduction apparently takes place in one main step, around 450°C (for a total duration of 100 h), followed by a small exothermic step. The final product is a stoichiometric, well crystallized UO₂. XRD analysis shows the occurrence of two successive intermediates of which one has a structure close to that of UO₂, but with interstitial fluorine atoms. This revised version was published online in August 2006 with corrections to the Cover Date.     

A catalyst-free protocol for direct oxidative esterification of alcohols and aldehydes

A fast, simple, and efficient protocol for the direct conversion of alcohols and aldehydes to methyl ester has been developed using TsNBr₂ without any catalyst. The one pot reaction proceeds in the presence of a base at room temperature in methanol, to produce the corresponding methyl ester in high yield within a short time.     

Rh(I)-catalyzed allenic Pauson-Khand reaction: first construction of the bicyclo[6.3.0]undecadienone ring system

The Rh(I)-catalyzed Pauson-Khand reaction of allenynes afforded the bicyclo[6.3.0]undecadienones as well as their benzo and furo derivatives. In addition, a novel [RhCl(CO)₂]₂-catalyzed [2,3]-sigmatropic rearrangement of the sulfinic ester species of propargyl alcohols was developed.     

超临界流体干燥法制备纳米TiO2-SnO2-SiO2复合光催化剂及其光催化性能研究

半导体多相光催化法作为一种污染治理新技术越来越受到人们的重视,在所使用的半导体光催化剂中,TiO2以无毒,催化活性高,价廉,无污染等特点,成为最具有前途的绿色环保型催化剂之一[1],但其自身具有局限性,如禁带宽度大,需在近紫外光下才能激发产生电子空穴对,对太阳光的利用率仅