Binary diffusion coefficients of phenolic compounds in subcritical water using a chromatographic peak broadening technique

Infinite dilution diffusion coefficients of certain phenolic compounds were measured as a function of temperature in water slightly acidified with formic acid using the Taylor dispersion method. The diffusion coefficients calculated using the chromatographic peak broadening technique were found to increase exponentially with an increase in the temperature. The diffusion coefficients of the selected phenolic compounds did not vary as a function of their molecular weights and the diffusion coefficients of the phenolic compounds increased as a function of temperature (from 2.16 × 10⁻¹⁰ m² s⁻¹ at 298 K to 5.79 × 10⁻¹⁰ m² s⁻¹ at 413 K for malvidin-3,5-diglucoside). However, for some phenolic compounds such as gallic acid monohydrate, quercetin-3-β-d-glucoside, protocatechuic acid and (−)-epicatechin, there were difficulties in making measurements above temperatures of 352 K, 372 K, 392 K and 413 K, respectively, due to thermal degradation of the phenolic compounds in water above these temperatures. The experimentally measured diffusion coefficients of the phenolic compounds were correlated as a function of temperature and solvent viscosity and were compared with those predicted using theoretical models. The validity of the Stokes-Einstein diffusion model in predicting the diffusion coefficients of the phenolic compounds in hot pressurized water was also evaluated.     

Absorption and emission behaviour of trans-p-coumaric acid in aqueous solutions and some organic solvents

The absorption and fluorescence behaviour of trans-p-coumaric acid (trans-4-hydroxycinnamic acid) is investigated in buffered aqueous solution over a wide range from pH 1 to pH 12, in un-buffered water, and in some organic solvents. Absorption cross-section spectra, fluorescence quantum distributions, fluorescence quantum yields, and degrees of fluorescence polarisation are measured. p-Coumaric acid exists in different ionic forms in aqueous solution depending on the pH. There is an equilibrium between the neutral form (p-CAH₂) and the single anionic form (p-CAH⁻) at low pH (pK_na ≈ 4.9), and between the single anionic and the double anionic form (p-CA²⁻) at high pH (pK_aa ≈ 9.35). In the organic solvents studied trans-p-coumaric acid is dissolved in its neutral form. The fluorescence quantum yield of trans-p-coumaric acid in aqueous solution is ?_F ≈ 1.4 × 10⁻⁴ for the neutral and the single anionic form, while it is ?_F ≈ 1.3 × 10⁻³ for the double anionic form. For trans-p-coumaric acid in organic solvents fluorescence quantum yields in the range from 4.8 × 10⁻⁵ (acetonitrile) to 1.5 × 10⁻⁴ (glycerol) were measured. The fluorescence spectra are 7700–10,000 cm⁻¹ Stokes shifted in aqueous solution, and 5400–8200 cm⁻¹ Stokes shifted in the studied organic solvents. Decay paths responsible for the low fluorescence quantum yields are discussed (photo-isomerisation and internal conversion for p-CA²⁻, solvent-assisted intra-molecular charge-transfer or ππ^∗ to nπ^∗ transfer and internal conversion for p-CAH₂ and p-CAH⁻). The solvent dependence of the first ππ^∗ electronic transition frequency and of the fluorescence Stokes shift of p-CAH₂ is discussed in terms of polar solute–solvent interaction effects. Thereby the ground-state and excite-state molecular dipole moments are extracted.     

A readily observed base-catalyzed isotopic exchange in a 2,4-dinitroalkyl benzene

The behaviour of solutions of the sodium salt of 4-(2,4-dinitrophenyl)pentanoic acid in D₂O is readily monitored by ¹H NMR spectroscopy. In the presence of excess NaOD, these show exchange of hydrogen at the 3-position of the benzene ring with k_OD = 1.23(0.03) × 10⁻⁴ M⁻¹ s⁻¹ at 25 °C. Rates of exchange using solutions with triethylamine buffers show no dependence on buffer concentration and an estimate of the acid dissociation constant, pK_a ≈ 29.3, of the dinitrobenzene is made. Under the conditions, there is no detectable exchange at the benzylic position.     

Chemiluminescence determination of ultramicro DNA with a flow-injection method

A high sensitive flow-injection chemiluminescence method for determination of calf thymus DNA and herring sperm DNA has been developed. The method is based on the chemiluminescence reaction of Rhodamine B-cerium(IV)-thermally denatured DNAs in sulfuric acid media. The proposed procedure allows quantitation of DNAs in the range 2.6×10⁻⁵ to 0.26 μg ml⁻¹ for calf thymus DNA and 5.0×10⁻⁸ to 5.0×10⁻⁵ μg ml⁻¹ for herring sperm DNA with correlation coefficients 0.9998 and 0.9996 (both n=11), respectively. The detection limits (3σ) are 6.5×10⁻⁶ μg ml⁻¹ for calf thymus DNA and 4.3×10⁻⁸ μg ml⁻¹ for herring sperm DNA. The possible mechanism of chemiluminescence in the system is discussed.     

Determination of indole-3-acetic acid and indole-3-butyric acid in mung bean sprouts using high performance liquid chromatography with immobilized Ru(bpy)3-KMnO4 chemiluminescence detection

A novel method for determination of indole-3-acetic acid (IAA) and indole-3-butyric acid (IBA) in an extract from mung bean sprouts using high performance liquid chromatography (HPLC) with chemiluminescence (CL) detection is described. The method is based on the CL reaction of auxin (indole-3-acetic acid and indole-3-butyric acid) with acidic potassium permanganate (KMnO₄) and tris(2,2′-bipyridyl)ruthenium(II), which was immobilized on the cationic ion-exchange resin. The chromatographic separation was performed on a Nucleosil RP-C18 column (i.d.: 250 mm × 4.6 mm, particle size: 5 μm, pore size: 100) with an isocratic mobile phase consisting of methanol-water-acetic acid (45:55:1, v/v/v). At a flow rate of 1.0 mL min⁻¹, the total run time was 20 min. Under the optimal conditions, the linear ranges were 5.0 × 10⁻⁸ to 5.0 × 10⁻⁶ g mL⁻¹ and 5.0 × 10⁻⁷ to 1.0 × 10⁻⁵ g mL⁻¹ for IAA and IBA, respectively. The detection limits were 2.0 × 10⁻⁸ g mL⁻¹ and 2.0 × 10⁻⁷ g mL⁻¹ for IAA and IBA, respectively. The relative standard deviation (RSD) of intra-day were 3.1% and 2.3% (n = 11) for 2 × 10⁻⁶ g mL⁻¹ IAA and 2 × 10⁻⁶ g mL⁻¹ IBA; The relative standard deviations of inter-day precision were 6.9% and 4.9% for 2 × 10⁻⁶ g mL⁻¹ IAA and 2 × 10⁻⁶ g mL⁻¹ IBA. The proposed method had been successfully applied to the determination of auxin in mung bean sprouts.     

Foreign gas broadening and shift of the strongly “forbidden” lead line at 1278.9 nm

The collisional broadening and shift rate coefficients of the “forbidden“ 6p^{2 3}P₀ → 6p^{2 3}P₁ transition in lead were determined by diode laser absorption measurements performed simultaneously in two resistively heated hot-pipes. One hot-pipe contained Pb vapor and noble gas (Ar or He) at low pressure, while the other was filled with Pb and noble gas at variable pressure. The measurements were performed at temperatures of 1220 K and 1290 K, i.e., lead number densities of 4.8 × 10¹⁵ cm^− 3 and 1.2 × 10¹⁶ cm^− 3. The broadening rates were obtained by fitting the experimental collisionally broadened absorption line shapes to theoretical Voigt profiles. The shift rates were determined by measuring the difference between the peak absorption positions in the spectra measured simultaneously in the heat pipe filled with noble gas at reference pressure and the one with noble gas at variable pressure. The following data for the broadening and shift rate coefficients due to collisions with Ar and He were obtained: γ_B^Ar = (3.4 ± 0.1) × 10^− 10 cm³ s^− 1, γ_B^He = (3.8 ± 0.1) × 10^− 10 cm³ s^− 1, γ_S^Ar = (− 7.3 ± 0.8) × 10^− 11 cm³ s^− 1, γ_S^He = (− 6.5 ± 0.7) × 10^− 11 cm³ s^− 1.     

Use of the molybdenum-thiocyanate-rhodamine 6G ternary complex for spectrophotometric molybdenum determination without extraction

A modified thiocyanate method without extraction by using rhodamine 6G as a secondary ligand was developed. Molybdenum in 1.0×10⁻² M HCl, after the addition of ascorbic acid, was heated for 10 min in a 90 °C water bath for reduction. Suitable amounts of glycerine, Triton X-100, rhodamine 6G solutions and 2+1 (v/v) 9 M H₂SO₄+3 M KHSO₄ were added in this order. This solution was allowed to cool to room temperature and the absorbance at 570 nm was measured against a reagent blank 45 min after the addition of thiocyanate solution and the second aliquot of Triton X-100 solution. The complex was stable for at least 4 h, the order of reagent addition was important, and thiocyanate should be in large excess. Beer’s law was obeyed over the range 0.9×10⁻⁶ to 1.1×10⁻⁵ M Mo with the molar absorptivity being 1.1×10⁵ l mol⁻¹ cm⁻¹. The R.S.D. for the determination of 0.7 mg Mo l⁻¹ was 1.83% (n=8). Possible interferences of various cations and anions on molybdenum determination were studied. The proposed method was applied to the determination of molybdenum in a dental alloy, Wiron 99.     

Preparation of silver hexacyanoferrate nanoparticles and its application for the simultaneous determination of ascorbic acid, dopamine and uric acid

A silver hexacyanoferrate nanoparticles/carbon nanotubes modified glassy carbon electrode was fabricated and then successfully used for the simultaneous determination of ascorbic acid, dopamine and uric acid by cyclic voltammetry. A detailed investigation by transmission electron microscopy (TEM) and electrochemistry was performed in order to elucidate the preparation process and properties of the nanocomposites. The size of silver hexacyanoferrate nanoparticles was examined by TEM around 27 nm. Linear calibration plots were obtained over the range of 4.0 × 10⁻⁶-7.8 × 10⁻⁵, 2.4 × 10⁻⁶-1.3 × 10⁻⁴ and 2.0 × 10⁻⁶-1.5 × 10⁻⁴ mol L⁻¹ with detection limits of 4.2 × 10⁻⁷,1.4 × 10⁻⁷ and 6.0 × 10⁻⁸ mol L⁻¹ for ascorbic acid, dopamine and uric acid, respectively. The practical analytical utilities of the modified electrode were demonstrated by the determination of ascorbic acid, dopamine and uric acid in urine and human blood serum samples.     

Thermophysical properties of SrHfO3 and SrRuO3

Polycrystalline samples of strontium series perovskite type oxides, SrHfO₃ and SrRuO₃ were prepared and the thermophysical properties were measured. The average linear thermal expansion coefficients are 1.13×10⁻⁵ K⁻¹ for SrHfO₃ and 1.03×10⁻⁵ K⁻¹ for SrRuO₃ in the temperature range between 423 and 1073 K. The melting temperatures T_m of SrHfO₃ and SrRuO₃ are 3200 and 2575 K, respectively. The longitudinal and shear sound velocities were measured by an ultrasonic pulse-echo method at room temperature in air, which enables to evaluate the elastic moduli and Debye temperature. The heat capacity was measured by using a differential scanning calorimeter, DSC in high-purity argon atmosphere. The thermal diffusivity was measured by a laser flash method in vacuum. The thermal conductivities of SrHfO₃ and SrRuO₃ at room temperature are 5.20 and 5.97 W m⁻¹ K⁻¹, respectively.     

Self-standing single lithium ion conductor polymer network with pendant trifluoromethanesulfonylimide groups: Li diffusion coefficients from PFGSTE NMR

Solid electrolyte materials have the potential to improve performance and safety characteristics of batteries by replacing conventional solvent-based electrolytes. For this purpose, new candidate single ion conductor self-standing networks were synthesized with trifluoromethane-sulfonylimide (TFSI) lithium salt based monomer using poly(ethyleneglycol) dimethacrylate (PEGDM 750) as crosslinker. The highest ionic conductivity was 3.4 × 10⁻⁷ S cm⁻¹ at 30 °C in the dry state. Thermal and mechanical analyses showed good thermal stability up to 190 °C and rubbery-like properties at ambient temperature. A direct relationship between ionic conductivity and glassy or rubbery state of the membranes was found. Vogel–Tammann–Fulcher behavior was observed in the dry state which is consistent with a lithium conductivity correlated with polymer chain mobility. By swelling the network in propylene carbonate, a self-standing electrolyte gel could be obtained with an ionic conductivity as high as 1 × 10⁻⁴ S cm⁻¹ at 30 °C. The individual diffusion coefficients of mobile species in the material (¹⁹F and ⁷Li) were measured and quantified using pulsed-field gradient nuclear magnetic resonance (PFG-NMR). Diffusion coefficients for the most mobile components of the lithium cations and fluorinated anions at 100 °C in dry membranes have been found to be 3.4 × 10⁻⁸ cm² s⁻¹ and 2.1 × 10⁻⁸ cm² s⁻¹ respectively.     

Flow-injection chemiluminescence determination of aminomethylbenzoic acid and aminophylline based on N-bromosuccinimide-luminol reaction

A novel and sensitive chemiluminescence (CL) method for the determination of aminomethylbenzoic acid and aminophylline coupled with flow-injection analysis (FIA) technique is developed in this paper. It is based on the inhibition effect of the studied drugs on the chemiluminescence emission of N-bromosuccinimide-luminol (NBS-luminol) system. Under the optimum conditions, the decreased CL intensity is linear with the concentration of aminomethylbenzoic acid in the range of 2×10⁻⁸ to 1.0×10⁻⁶ g ml⁻¹ and with the concentration of aminophylline in the range of 1×10⁻⁷ to 7.0×10⁻⁶ g ml⁻¹, respectively. The detection limit is 7.0×10⁻⁹ g ml⁻¹ for aminomethylbenzoic acid (3σ) and 3.4×10⁻⁸ g ml⁻¹ for aminophylline (3σ). The relative standard deviations (R.S.D.) for 11 parallel measurements of 2.0×10⁻⁷ g ml⁻¹ aminomethylbenzoic acid and 1.0×10⁻⁶ g ml⁻¹ aminophylline are 2.6 and 3.0%, respectively. The proposed methods have been applied for the determination of the studied drugs in their pharmaceutical formulations with satisfactory results. The possible use of the proposed system for the determination of aminomethylbenzoic acid in plasma sample was also tested. The possible inhibition mechanism of aminomethylbenzoic acid and aminophylline on luminol-NBS system was discussed briefly.     

ZnS quantum dots derived a reagentless uric acid biosensor

A reagentless amperometric uric acid biosensor based on zinc sulfide (ZnS) quantum dots (QDs) was firstly developed. It could detect uric acid without the presence of an electron mediator. The carboxyl group functionalized ZnS QDs were synthesized, and they were soluble biocompatible and conductive. ZnS QDs conjugates could provide increased enzyme binding sites, which may result in higher enzyme loading. Thus, the proposed uricase/ZnS QDs/l-cys biosensor exhibited higher amperometric response compared to the one without QDs (uricase/l-cys biosensor). In addition, there was little AA interference. It showed a linear dependence on the uric acid concentration ranging from 5.0 × 10⁻⁶ to 2.0 × 10⁻³ mol L⁻¹ with a detection limit of 2.0 × 10⁻⁶ mol L⁻¹ at 3σ.     

Linear polyamines as carriers in thiocyanate-selective membrane electrodes

The polyamines, octyl-[2-(2-octylamino-ethylamino)-ethyl]-amine (L¹) and octyl-{2-[2-(2-octylamino-ethylamino)-ethylamino]-ethyl}-amine (L²), have been used as anion ionophores in PVC-based membrane ion-selective electrodes. Different electrodes were prepared containing L¹, or L², and o-nitrophenyl octyl ether (NPOE) or bis(2-ethylhexyl)sebacate (DOS) as plasticizers. The response of the electrodes was tested in two different buffers, HEPES-KOH (pH 7) and MES-KOH (pH 5.6). Electrodes containing L¹ and L² with NPOE (E1 and E2, respectively) showed a Nernstian response for thiocyanate with a good response time. The detection limit, linear range and slope for electrode E1 were 3.8 × 10⁻⁶ mol dm⁻³, 1 × 10⁻⁵ to 1 × 10⁻¹ mol dm⁻³ and −57.2 mV decade⁻¹ at pH 5.6 and 4.47 × 10⁻⁶ mol dm⁻³, 1.95 × 10⁻⁵ to 1 × 10⁻¹ mol dm⁻³ and −58.1 mV decade⁻¹ at pH 7.0. For electrode E2 the detection limit, linear range and slope found were 2.63 × 10⁻⁶ mol dm⁻³, 7.94 × 10⁻⁶ to 1 × 10⁻¹ mol dm⁻³ and −58.5 mV decade⁻¹ at pH 5.6 and 1.23 × 10⁻⁵ mol dm⁻³, 7.95 × 10⁻⁵ to 1 × 10⁻¹ mol dm⁻³ and −46.0 mV decade⁻¹ at pH 7. In contrast, electrodes containing DOS as plasticizers gave only response at pH 5.6 (detection limit, linear range and slope at pH 5.6 were 3.16 × 10⁻⁵ mol dm⁻³, 1 × 10⁻⁴ to 1 × 10⁻¹ mol dm⁻³ and −52.6 mV decade⁻¹). Selectivity coefficients for different anions with respect to thiocyanate were calculated. The electrode E2 at pH 5.6 was also used for the determination of SCN⁻ by potentiometric titrations with Ag⁺ ions with good results. The electrode E2 was also used to determine concentrations of thiocyanate in biological samples.     

Synchronous fluorescence determination of urinary 1-hydroxypyrene, β-naphthol and 9-hydroxyphenanthrene based on the sensitizing effect of β-cyclodextrin

A novel method for the simultaneous determination of 1-hydroxypyrene (1-OHP), β-naphthol (β-NAP) and 9-hydroxyphenanthrene (9-OHPe) in human urine has been established by using synchronous fluorescence spectrometry. It was based on the fact that synchronous fluorescence spectrometry can resolve the broad-band overlapping of conventional fluorescence spectra, which arise from their similar molecular structures. Only one single scan is needed for quantitative determination of three compounds simultaneously when Δλ = 15 nm is chosen. The signals detected at these three wavelengths, 369.6, 330.0 and 358.0 nm, vary linearly when the concentration of 1-OHP, β-NAP and 9-OHPe is in the range of 2.16 × 10⁻⁸-1.50 × 10⁻⁵ mol L⁻¹, 1.20 × 10⁻⁷-1.10 × 10⁻⁵ mol L⁻¹ and 1.07 × 10⁻⁷-3.50 × 10⁻⁵ mol L⁻¹, respectively. The correlation coefficients for the standard calibration graphs were 0.994, 0.999 and 0.997 (n = 7) for 1-OHP, β-NAP and 9-OHPe, respectively. The limits of detection (LOD) for 1-OHP, β-NAP and 9-OHPe were 6.47 × 10⁻⁹ mol L⁻¹, 3.60 × 10⁻⁸ mol L⁻¹ and 3.02 × 10⁻⁸ mol L⁻¹with relative standard deviations (R.S.D.) of 4.70-6.40%, 2.80-4.20%, 3.10-4.90% (n = 6), respectively. The method described here had been applied to determine traces of 1-OHP, β-NAP and 9-OHPe in human urine, and the obtained results were in good agreement with those obtained by the HPLC method. In addition, the interaction modes between β-cyclodextrin (β-CD) and 1-OHP, β-NAP or 9-OHPe, as well as the mechanism of the fluorescence enhancement were also discussed.     

Flow-injection turbidimetric determination of homatropine methylbromide in pharmaceutical formulations using silicotungstic acid as precipitant reagent

A flow-injection turbidimetric procedure exploiting merging zones is proposed for determining homatropine methylbromide (HMB) in pharmaceutical preparations. The determination is based on the precipitation reaction of homatropine methylbromide with silicotungstic acid in acidic medium to form a precipitate, which was measured at 410 nm. The analytical curve was linear in the HMB concentration range from 8.1 × 10⁻⁵ to 2.2 × 10⁻⁴ mol l⁻¹, with a detection limit of 5.0 × 10⁻⁶ mol l⁻¹. The recoveries ranged from 96 to 103%, the sampling frequency was 70 determinations per hour and relative standard deviations were less than 1.5% (n = 10). The results obtained for commercial formulations using the FIA procedure were in good agreement with those obtained by using a comparative method.     

Sunflower leaves tissue-based bioelectrode with amperometric flow-injection system for glycolic acid determination in urine

A novel plant tissue-based bioelectrode obtained by incorporating sunflower (Helianthus annuus L.) leaves tissue as a source of glycolate oxidase and peroxidase into a ferrocene-mediated carbon paste electrode for the determination of glycolic acid was developed. It was coupled with the flow-injection (FI) system and used as the basis to develop a novel FI amperometric procedure for glycolic acid determination. The flow-injection amperometric measurements were performed by injecting aliquot of glycolic acid solution into the flowing stream of 0.05 mol L⁻¹ of phosphate buffer solution having pH 8.0 with a flow rate of 0.3 mL min⁻¹. The bioelectrode consisted of 20% (w/w) of sunflower leaves tissue and 5% (w/w) of ferrocene at 0.00 V (vs Ag/AgCl). The bioelectrode exhibited a linear response from 1.0 × 10⁻⁶ up to 2.0 × 10⁻³ mol L⁻¹ glycolic acid with a detection limit (S/N = 3) and a quantitation limit (S/N = 10) of 1 × 10⁻⁶ and 3.3 × 10⁻⁶ mol L⁻¹, respectively. The sampling rate of 12 h⁻¹ and a relative standard deviation of 1.67% (n = 15) were achieved. The bioelectrode response decreased to 70% of the original value within 90 continuous injections. The proposed bioelectrode was satisfactorily applied to glycolic acid determination in human urine samples after appropriate sample pretreatment. Results obtained by the FI method were compared favorably with those obtained by HPLC. It offers advantages, which included rapidity, high activity, limited stability, ease of preparation and low cost.     

Ab initio investigation of O3 addition to double bonds of limonene

The reaction of the O₃ addition to double bonds of the limonene in the gas phase has been investigated using ab initio methods. Four different possibilities for the O₃ addition to the double bonds, which correspond to the two C–C double bonds (endocyclic or exocyclic), and two different orientations of each C–C double bonds, have been considered. The corresponding rate constants have been calculated using the transition-state theory (TST) at the CCSD(T)/6-31G(d) + CF//B3LYP/6-311+G(d,p) level of theory. The high-pressure limit of the overall rate constant at 298 K is found to be ∼2.92 × 10⁻¹⁶ cm³ molecule⁻¹ s⁻¹ that is in a good agreement with the experimental data, and the rate constants of the four individual reaction channels turn out to be 2.1 × 10⁻¹⁶ cm³ molecule⁻¹ s⁻¹, 1.2 × 10⁻¹⁷ cm³ molecule⁻¹ s⁻¹, 6.5 × 10⁻¹⁷ cm³ molecule⁻¹ s⁻¹ and 5.1 × 10⁻¹⁸ cm³ molecule⁻¹ s⁻¹ for 1-endo, 2-endo, 1-exo and 2-exo, respectively.     

Moisture barrier,wetting and mechanical properties of shellac/agar or shellac/cassava starch bilayer bio-membrane for food applications

Edible bilayer membrane composed of agar (AG) or cassava starch (CAS) as a cohesive structural layer and ethanol-cast shellac layer as a moisture barrier are investigated for their potential use in food preservation as bio-packaging film, membrane or coating. Bilayer membranes containing non-plasticized shellac exhibit low water vapor permeability (WVP), from 0.89 to 1.03 × 10⁻¹¹ g m⁻¹ s⁻¹ Pa⁻¹. A high value of contact angle (≈92°) and a low liquid water adsorption rate (26 × 10⁻³ μL s⁻¹) indicate that these barrier layers have a quite hydrophobic surface. However, the rigid and brittle characteristics of shellac induce a lack of integrity for this layer. It tends to be cracked and scaled off. The incorporation of PEG 200 (plasticizer) into shellac improves the flexibility that prevents the defects in structure and reinforces the adhesion between the shellac and the cohesive-structural layer. The use of plasticizer weakly affects the WVP of bilayer membranes; however, the surface hydrophobicity as well as the liquid water adsorption rate is comparable to that of non-plasticized shellac layer. Furthermore, PEG increases the stretchability of bilayer membranes. Either being plasticized or not, shellac layer could improve significantly the functional properties of bilayer barriers and give a promising use as biopackaging.     

Kinetic study of proton-bound dimer formation using ion mobility spectrometry

A method to measure the rate constant for the formation of symmetrical proton-bound dimers at ambient pressure was proposed. The sample is continuously delivered to the drift region of an ion mobility spectrometer where it reacts with a swarm of monomer ions injected by the shutter grid. Dimer ions are formed in the drift tube and a tail appears in the ion mobility spectrum. The rate constant is derived from the mobility spectra. The proposed approach was typically examined for methyl isobutyl ketone (MIBK), 2,4-dimethyl pyridine (DMP), and dimethyl methyl phosphonate (DMMP). The rate constants measured in this study were: 0.25 × 10⁻⁹, 0.86 × 10⁻¹⁰, and 0.47 × 10⁻¹⁰ cm³ s⁻¹ for MIBK, DMP and DMMP, respectively. The logarithm of the measured rate constants were found to be almost independent of reciprocal temperature within 303 to 343 K, indicating that no activation energy is involved in the formation of proton-bound dimers.     

Localized surface plasmon resonance sensor for simultaneous kinetic determination of peroxyacetic acid and hydrogen peroxide

A new sensor for simultaneous determination of peroxyacetic acid and hydrogen peroxide using silver nanoparticles (Ag-NPs) as a chromogenic reagent is introduced. The silver nanoparticles have the catalytic ability for the decomposition of peroxyacetic acid and hydrogen peroxide; then the decomposition of them induces the degradation of silver nanoparticles. Hence, a remarkable change in the localized surface plasmon resonance absorbance strength could be observed. Spectra-kinetic approach and artificial neural network was applied for the simultaneous determination of peroxyacetic acid and hydrogen peroxide. Linear calibration graphs were obtained in the concentration range of (8.20 × 10⁻⁵ to 2.00 × 10⁻³ mol L⁻¹) for peroxyacetic acid and (2.00 × 10⁻⁵ to 4.80 × 10⁻³ mol L⁻¹) for hydrogen peroxide. The analytical performance of this sensor has been evaluated for the detection of simultaneous determination of peroxyacetic acid and hydrogen peroxide in real samples.