A compact miniaturized continuous flow system for the determination of urea content in milk

A multicommutation-based flow system with photometric detection was developed, employing an analytical microsystem constructed with low temperature co-fired ceramics (LTCC) technology, a solid-phase reactor containing particles of Canavalia ensiformis DC (urease source) immobilized with glutaraldehyde, and a mini-photometer coupled directly to the microsystem which monolithically integrates a continuous flow cell. The determination of urea in milk was based on the hydrolysis of urea in the solid-phase reactor and the ammonium ions produced were monitored using the Berthelot reaction. The analytical curve was linear in the urea concentration range from 1.0 × 10⁻⁴ to 5.0 × 10⁻³ mol L⁻¹ with a limit of detection of 8.0 × 10⁻⁶ mol L⁻¹. The relative standard deviation (RSD) for a 2.0 × 10⁻³ mol L⁻¹ urea solution was lower than 0.4% (n = 10) and the sample throughput was 13 h⁻¹. To check the reproducibility of the flow system, calibration curves were obtained with freshly prepared solutions on different days and the RSD obtained was 4.7% (n = 6). Accuracy was assessed by comparing the results of the proposed method with those from the official procedure and the data are in close agreement, at a 95% confidence level.     

Electrochemical kinetic study about cobalt electrodeposition onto GCE and HOPG substrates from sulfate sodium solutions

In the present work, we analyze the electrodeposition of cobalt by electrochemical techniques onto GCE (system I) and HOPG (system II) electrodes from sulfate solutions. Cyclic voltammetry and current transient measurements were used to obtain the nucleation and growth mechanism. The results clearly showed that electrodeposition of cobalt is a diffusion-controlled process with a typical 3D nucleation mechanism in both substrates. The average ΔG calculated for the stable nucleus formation was 1.97 × 10⁻²⁰ J nuclei⁻¹ and 3.58 × 10⁻²⁰ J nuclei⁻¹ for system I and system II, respectively. The scanning electron microscope (SEM) images indicated similar nucleation and growth processes on GCE and HOPG substrates at same overpotential with a homogeneous disperse cobalt clusters. X-ray energy-dispersive spectroscopy (EDS) was performed in order to ensure that the clusters formed are cobalt. The nuclei’s size obtained was dependent of the overpotential applied; at lower overpotentials, the growth rate of the cobalt clusters diminishes when their number increases due to the strongly reduced concentration of cobalt ions because of their consumption by a larger number of growing particles. A theoretical quantum study employing PM6 method suggests that Na⁺ adsorbed deactivate the local surface occasionating the formation of disperse cobalt clusters on carbon electrodes.     

Photoinduced electron transfer between triplet erythrosin dianion and highly charged ionic quenchers

Abstract  

The lifetime of the lowest triplet state of the dianion erythrosin B depends on its concentration because of self-quenching. The self-quenching rate constants vary with the solution viscosity at room temperature. Dextrose was used to change the viscosity of aqueous solutions in the range 1 ≤ η ≤ 5.31 cP. Photoinduced electron transfer reactions between the triplet state of the erythrosin dianion and the highly charged ionic quenchers K₄[Fe(CN)₆] and K₄[Mo(CN)₈] were investigated in aqueous borate buffer solutions at pH 9.2 using flash photolysis. Electron transfer rates vary from 3.0 × 10⁸ to 1.4 × 10⁸ M⁻¹ s⁻¹ depending on viscosity.     

A laser photolysis study of the quenching kinetics of triplet-state all-<Emphasis Type="Italic">trans</Emphasis>-retinal by oxygen in aqueous albumin and liposome solutions

The kinetics of quenching of the all-trans-retinal triplet state by air oxygen in aqueous solutions of bovine serum albumin and in a cardiolipin liposome suspension was investigated by nanosecond laser photolysis. It was established that the quenching reaction rate constant in the albumin solution (1.8 × 10⁸ l mol⁻¹ s⁻¹) was an order of magnitude less than in liposomes (3.1 × 10⁹ l mol⁻¹ s⁻¹). These constants were 5.0 × 10⁹ and 1.1 × 10⁹ l mol⁻¹ s⁻¹ in methanol and aqueous solutions containing 10 vol % methanol, respectively. The effect of hindered oxygen access to the Lall-trans-retinal attached to albumin is discussed in terms of its influence on the photooxidation processes in the retina.     

Temperature effect on the volume properties of a bisurea aqueous solutions

The densities of aqueous solutions of bisurea (2,4,6,8-tetraazabicyclo[3.3.0]octane-3,7-dione) were measured using a vibrating-tube densimeter at 288.15, 298.15, 308.15, and 318.15 K in the concentration range up to ∼3·10⁻³ moles of solute (1000 g of H₂O)⁻¹ with the error at most ±5· 10⁻⁶ g cm⁻³ (reproducibility up to 2·10⁻⁶ g cm⁻³). The limiting partial molar volume and expansibility of bisurea in water were calculated. The bicyclic molecules under study form in aqueous solution H-bonded hydrate complexes with rather high structure-packing density. These complexes are more subjected to the destroying effect of temperature than the corresponding urea complexes. The hydration of bisurea weakens with the temperature increase. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 1929–1932, October, 2007.     

Catalytic effect of cuprous ions on the thermal decomposition of 3,3,6,6-tetramethyl-1,2,4,5-tetraoxane in methanol solution

Thermal decomposition of 3,3,6,6-tetramethyl-1,2,4,5-tetraoxane was examined in methanol solution (1.69×10⁻² M) containing cuprous ions (5.05×10⁻⁷ M) in the temperature range from 130 to 166°C using UV spectroscopy as analytical method. The ion-catalyzed reaction follows first-order kinetics with respect to the peroxide and added cuprous ions. The temperature effect on the rate of thermal decomposition of the title compound was described by the corresponding Arrhenius equations, and its stability in solution was estimated on a quantitative level. The activation parameters of the initial step of decomposition of 3,3,6,6-tetramethyl-1,2,4,5-tetraoxane were determined (ΔH ^≠ = 14.7±0.8 kcal mol⁻¹; ΔS ^≠ = −38.9±1.4 cal mol⁻¹ K⁻¹; ΔG ^≠ = 31.0±0.8 kcal mol⁻¹). Electron-transfer mechanism was proposed for the reaction under study. The text was submitted by the authors in English.     

Thermodynamic properties of some polymeric forms of fullerite C<Subscript>60</Subscript> at temperatures ranging from 0 to 320 K

The temperature dependences of the heat capacityC ⁰ _p of fullerites C₆₀ were studied at temperatures ranging from 5 to 320 K in an adiabatic vacuum calorimeter with an accuracy of 0.4–0.2%. The fullerite C₆₀ samples were prepared by treating the starting fullerite C₆₀ under 8 GPa at 920 and 1270 K and “quenched” by a sharp decrease in pressure to −10⁵ Pa and in temperature to ∼300 K. Fullerite C₆₀(8 GPa, 920 K), a crystalline polymer with layered structure formed by polymerized fullerene C₆₀ molecules, was obtained at 920 K and 8 GPa. Fullerite C₆₀(8 GPa, 1270 K), a three-dimensional polymer with a graphite-like structure formed by fragments of decomposed C₆₀ molecules and containing many C(sp³)−C(sp³) bonds, was obtained at 1270 K and 8 GPa. Both polymers are metastable polymeric phases. The anomalous character of the temperature dependence of the heat capacity was revealed in the 49–66 K range for the polymer formed at 1270 K. The thermodynamic functions of the substances under study were calculated for the 0–320 K region along with entropies of their formation from graphite. The entropies of transformation of the starting fullerite C₆₀ into metastable phases and that of intertransformation of phases were estimated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2, pp. 277–281, February, 2000.     

Lactonization and Protonation of Gluconic Acid: A Thermodynamic and Kinetic Study by Potentiometry,NMR and ESI-MS

In acidic aqueous solutions, the protonation of gluconate is coupled with the lactonization of gluconic acid. With a decrease of pC _H, two lactones (δ- and γ-) are sequentially formed. The δ-lactone forms more readily than the γ-lactone. In 0.1 mol⋅L⁻¹ gluconate solutions, if pC _H>2.5 then only the δ-lactone is generated. When the pC _H is decreased below 2.0, formation of the γ-lactone is observed although the δ-lactone still predominates. In solutions with I=0.1 mol⋅L⁻¹ NaClO₄ and room temperature, the deprotonation constant of the carboxylic group was determined to be log ₁₀ K _a=3.30±0.02 using the NMR technique, and the δ-lactonization constant obtained by batch potentiometric titrations was log ₁₀ K _L=−(0.54±0.04). Using ESI-MS, the rate constants for the δ-lactonization and the reverse hydrolysis reaction at pC _H≈5.0 were estimated to be k ₁=3.2×10⁻⁵ s⁻¹ and k ₋₁=1.1×10⁻⁴ s⁻¹, respectively.     

Crystallization behavior of single or pauci chain aggregates of isotactic polystyrene

Single and pauci chain aggregates of isotactic polystyrene (i-PS) were prepared by the freeze-drying process from dilute solutions with the concentration from 1×10⁻³ to 2×10⁻⁵ g/mL. It was found by DSC measurements that the melting point of samples gradually shifted to lower temperatures with the decrease of the solution concentration used for sample preparation. As a result, the lamella thickness of bulk samples and the samples prepared by the freeze-drying process from a solution of 2×10⁻⁵ g/mL was 19.3 and 12.6 nm, respectively. At 468.3 K the half crystallization time (t _1/2) of samples freeze-dried from a solution of 1×10⁻⁴ g/mL was about 36 s, which was merely one tenth of that of the bulk sample. In addition, the growth rate of spherulite (dr/dt) of samples prepared from a solution of 2×10⁻⁵ g/mL was faster than that of the bulk sample annealed at 478.3 K. All these results should be attributed to the fewer entanglements in samples prepared by freeze-drying process from dilute solutions, and presented clear evidence for the influence of chain entanglements on the crystallization behavior of polymers. __________ Translated from Chemical Journal of Chinese Universities, 2005, 26(10) (in Chinese)     

Study and Application of Electrochemical Behavior of Calcium-ARS on a Mercury Film Electrode

A sensitive complex absorptive wave of Ca-ARS was obtained by using differential pulse voltammetry when a mercury film glass carbon electrode was immersed in 0.1 mol L⁻¹ KOH and 4.5×10⁻⁴ mol L⁻¹ ARS solution. The peak potential obtained was −1.17 V (vs Ag-AgCl). The peak current was proportional to the concentration of calcium in the range of 5.0×10⁻⁸−4.2×10⁻⁵ mol L⁻¹. The detection limit was 2.0×10⁻⁸ mol L⁻¹. This method was applied successfully to determining traces of calcium in blood serum. The electrochemical behavior of the system was also studied by cyclic voltammetry, and the experiment results showed that the electrode process was an irreversible absorptive with two electrons participating. Translated from Journal of Beijing Normal University (Natural Science Edition), 2005, 41(2) (in Chinese)     

Perchlorate selective membrane electrodes based on a platinum complex

Three platinum(II) complexes were synthesized and studied to characterize their ability as an anion carrier in a PVC membrane electrode. The polymeric membrane electrodes (PME) and also coated glassy carbon electrodes (CGCE) prepared with one of these complexes showed excellent response characteristics to perchlorate ions. The electrodes exhibited Nernstian responses to ClO₄ ⁻ ions over a wide concentration range from 1.5 × 10⁻⁶ to 2.7 × 10⁻¹ M for PME and 5.0 × 10⁻⁷ to 1.9 × 10⁻¹ M for CGCE with low detection limits (9.0 × 10⁻⁷ M for PME and 4.0 × 10⁻⁷ M for CGCE). The electrodes possess fast response time, satisfactory reproducibility, appropriate lifetime and, most importantly, good selectivity toward ClO₄ ⁻ relative to a variety of other common anions. The potentiometric response of the electrodes is independent of the pH of the test solution in the pH range 2.0–9.0. The proposed sensors were used in potentiometric determination of perchlorate ions in mineral water and urine samples. Correspondence: Ahmad Soleymanpour, Department of Chemistry, Damghan Basic Science University, Damghan, Iran.     

Solidification of molten zinc chloride

Solidification of molten zinc chloride was studied both experimentally and theoretically. By isothermal thermal analysis the time needed for the melt to crystallize at a given temperature ranging between 453 and 553 K was determined and the data obtained were compared with those of a calculated TTT curve. The extremum coordinates (temperature T _N, time t _N) of the curve, critical cooling rate v _CR, interfacial energy σ, and an additional parameter of kinetics barrier for nucleation ɛ were determined as T _N=508 K, t _N=7.29 s, v _CR=11.38 K s⁻¹, σ=0.11956 J m⁻² and ɛ=0.5712. By non-isothermal method the critical cooling rate of glass formation was determined as 1.25 K s⁻¹.     

Photochemical synthesis of cadmium sulfide nanoparticles

The formation of cadmium sulfide nanoparticles upon UV irradiation of aqueous solutions of cadmium thiosulfates was established on the basis of spectroscopic and macroscopic data. The yield and size of the cadmium sulfide nanoparticles depend on the ratio of cadmium to thiosulfate ions in solution, the concentration of the solution, and the irradiation duration. The cadmium sulfide nanoparticles with a diameter of 4 nm were obtained by the photolysis of solutions with a concentration of 10⁻³ mol L⁻¹ at the ratio S₂O₃ ²⁻: Cd²⁺ = 2: 1.     

Kinetic characterization of the reduction of silica supported cobalt catalysts

Abstact  The reduction process of silica supported cobalt catalyst was studied by thermal analysis technique. The reduction of the catalyst proceeds in two steps:

Speciation analysis of inorganic antimony in soil using HPLC-ID-ICP-MS

Speciation analysis of Sb(III) and Sb(V) in a soil sample was performed through extraction and on-line isotope dilution concentration determination after a chromatographic separation. The total Sb concentration found in a through traffic contaminated soil sample was (4.17 μg g⁻¹, 0.3 μg g⁻¹ SD, n=6). It was determined using ICP-MS after soil digestion using the sodium peroxide sintering method. The optimized extraction procedure for speciation analysis was carried out using 100 mmol L⁻¹ citric acid at pH 2.08 by applying an ultrasonic bath for 45 min at room temperature. The effects of citric acid concentration (0–500 mmol L⁻¹), pH (1–6), and temperature (30–60°C) on inorganic antimony species distribution in the examined sample were studied and optimized. The separation of Sb(III) and Sb(V) was achieved using an anion exchange column (PRP-X100) and 10 mmol L⁻¹ EDTA and 1 mmol L⁻¹ phthalic acid at pH 4.5 as a mobile phase. The eluent from the HPLC was mixed with an enriched (94.2%) ¹²³Sb spike solution that was pumped by a peristaltic pump with a constant flow rate (0.5 mL min⁻¹) in a three-way valve. The blend passed directly to the Conikal nebulizer of the ICP-MS. By using the above extraction procedure and methodology, 43.2% Sb(V) (2.9% RSD, n=3) and 6.0% Sb(III) (1.3% RSD, n=3) of total Sb found in the sample could be detected. The detection limits achieved by the proposed method were 20 ng L⁻¹ and 65 ng L⁻¹ for Sb(V) and Sb(III), respectively. The precision, evaluated by using RSD with 100 ng L⁻¹ calibration solutions, was 2.7% and 3.2% (n=6) for Sb(V) and Sb(III), respectively, in aqueous solutions.     

Structural and electric properties of the Ce0.8(Sm1 ? xCax)0.2O2 ? δ system (x = 0.0–1.0)

CeO₂-based solid solutions with a fluorite structure are promising materials as electrolytes of medium-temperature electrochemical devices. This work presents the results of systematic studies of structural and electric properties and oxygen nonstoichiometry of the Ce_0.8(Sm_{1 − x} Ca _x )_0.2O_{2 − δ} system in a wide range of concentrations of 0 < x < 1 performed in order to establish the causes affecting the system conductivity and its behavior in a reducing medium. It is found that a single-phase solid solution of the fluorite type is formed in the whole concentration range. Parameters of its lattice cells decrease linearly at an increase in the concentration of Ca²⁺. Conductivity in air grows when calcium is added due to a decrease in the grain boundary resistance. The maximum conductivity in air was obtained for the composition of Ce_0.8(Sm_0.8Ca_0.2)_0.2O_{2 − δ} and is 13.71 × 10⁻³ S/cm at 873 K. Studies of the dependence of conductivity of the partial pressure of oxygen showed that electron conductivity is observed at a higher oxygen partial pressure at an increase in the temperature and calcium concentration. The critical partial pressure of oxygen ( p_O2 ^* )\left( {p_{O_2 }^* } \right) for the compositions of Ce_0.8(Sm_{1 − x} Ca _x )_0.2O_{2 − δ} with x = 0; 0.2, and 0.5 is 1.83 × 10⁻¹⁶, 1.73 × 10⁻¹³, and 3.63 × 10⁻¹³ atm at 1173 K, respectively, and 2.76 × 10⁻²¹, 5.05 × 10⁻¹⁸, and 1.31 × 10⁻¹⁸ atm at 1023 K.     

Voltammetric determination of <Emphasis Type="Italic">D</Emphasis>-penicillamine based on its homogeneous electrocatalytic oxidation with potassium iodide at the surface of glassy carbon electrode

The electrooxidation of D-penicillamine (D-PA) has been studied in the presence of potassium iodide in various buffered aqueous solutions (4.00 ≤ pH ≤ 9.00) at the surface of glassy carbon electrode using cyclic voltammetry, differential pulse voltammetry and chronoamperometry. It has been found that under optimum pH (pH 5.00) in cyclic voltammetry, the electrooxidation of D-PA in the presence of potassium iodide as a homogeneous mediator occurred at a potential about 220 mV less positive than that in absence of potassium iodide at the surface of glassy carbon electrode. The homogeneous electrocatalytic oxidation current wave of D-penicillamine was linearly dependent on the D-PA concentration and a linear calibration curve was obtained in the ranges 3.0 × 10⁻⁵−1.5 × 10⁻³ M and 9.0 × 10⁻⁶−1.2 × 10⁻⁴ M of D-PA with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods, respectively. The detection limits (2σ) were determined as 3.0 × 10⁻⁵ and 3.5 × 10⁻⁶ M with CV and DPV, respectively. This method was also used for voltammetric determination of D-PA in pharmaceutical preparation by standard addition method.     

A Fiber Optode for p-Nitrophenol Based on Covalently Bound 9-Allylaminoacridine

 Using 9-allylaminoacridine synthesized in this laboratory as the fluorescent agent an fiber optode for p-nitrophenol (p-Np) has been prepared. 9-Allylaminoacridine has a polymerizable olefin unit and can be copolymerized with hydrophilic monomer 2-hydroxypropyl methacrylate (HPMA) under UV irradiation. On silanized activated glass surface a 9-allylaminoacridine containing HPMA membrane has been covalently bound forming a stable optode membrane free of leaching problem. The analytical performance characteristics including reversibility, reproducibility, short-term stability and interference have been evaluated. The optode has relatively long lifetime with the spectral response characteristics not changing after one month use. The plot of log(I ₀/I − 1) versus logarithm of the p-NP solution concentration can piecewise be fitted with the straight line of the form of Stern-Volmer equation, with a detection limit of 9.0 × 10⁻⁸ mol L⁻¹. The relative standard deviation obtained from eight separate determinations for two p-NP concentrations, 1.0 × 10⁻⁵ and 4.0 × 10⁻⁴ mol L⁻¹, are 2.36% and 1.34%, respectively. p-Np can be determined in water samples with satisfactory recoveries. Received April 13, 2000. Revision September 28, 2000.     

Determination of arsenic in diesel, gasoline and naphtha by graphite furnace atomic absorption spectrometry using microemulsion medium for sample stabilization

A procedure for the determination of As in diesel, gasoline and naphtha at μg L⁻¹ levels by GFAAS is proposed. Sample stabilization was achieved by the formation of three component solutions prepared by mixing appropriate volumes of the samples propan-1-ol and nitric acid aqueous solution. This mixture resulted in a one-phase medium, which was indefinitely stable. No changes in the analyte signals were observed over several days in spiked samples, proving long-term stabilization ability. The use of conventional (Pd) and permanent (Ir) modification was investigated and the former was preferred. Central composite design multivariate optimization defined the optimum microemulsion composition as well as the temperature program. In this way, calibration using aqueous analytical solutions was possible, since the same sensitivity was observed in the investigated microemulsion media and in 0.2% v/v HNO₃. Coefficients of correlation larger than 0.999 and an As characteristic mass of 22 pg were observed. Recoveries (n=4) obtained from spiked samples were 98±4, 99±3 and 103±5%, and the limits of detection in the original samples were 1.8, 1.2 and 1.5 μg L⁻¹ for diesel, gasoline and naphtha, respectively. Validation was performed by the analysis of a set of commercial samples by independent comparative procedures. No significant difference (Student’s t-test, p<0.05) was observed between comparative and proposed procedure results. The total determination cycle lasted 4 min for diesel and 3 min for gasoline and naphtha, equivalent to a sample throughput of 7 h⁻¹ for diesel and 10 h⁻¹ for gasoline and naphtha.     

Kinetic studies on acid-catalysed aquation of some [Cr(ox)<Subscript>2</Subscript>(amino acid)]<Superscript>2−</Superscript> complexes

Three chromium(III) complexes of general formula [Cr(ox)₂(Aa)]²⁻ (Aa is an α-amino acid, namely alanine, valine or cysteine) were obtained and characterized in solution. In acidic solutions, [Cr(ox)₂(Aa)]²⁻ undergo acid-catalysed aquation to cis-[Cr(ox)₂(H₂O)₂]⁻ and the appropriate amino acid. The process goes through a metastable intermediate with monodentate amino acid coordinated via the carboxylate oxygen atom. The kinetics of the chelate ring opening were studied under isolation conditions. The determined pseudo-first-order rate constants were linearly dependent on [H⁺]. A mechanism is proposed, in which the reactive form of substrate is in the form of the conjugate acid.