Investigation of the “TECFLAM” Non-premixed Flame Using Large Eddy Simulation and Proper Orthogonal Decomposition

The confined turbulent swirling non-premixed TECFLAM S09c flame has been investigated using Large Eddy Simulation and a pre-calculated mixture-fraction-based flamelet model in a preliminary step to simulate this flame. The simplified formulation, despite the fact that it cannot capture localized extinctions, is found to reproduce the experimentally-observed vortex breakdown and the results agree well with available experimental data for velocity and mixture fraction. The unsteady flow features before the burner exit and inside the combustion chamber are analyzed with spectral analysis, correlations, and Proper Orthogonal Decomposition. The results show the presence of longitudinal vortices whose axes rotate with the swirl and which cause separation inside the inlet pipe. With combustion, some of the structures are damped and the spectral peaks shift to higher frequencies. Finally, simulations with the full 3D Conditional Moment Closure equation, which allows spatial and temporal fluctuations of the conditionally-filtered reacting scalars, reproduce successfully the flame lift-off observed experimentally.     

Numerical Simulation for Evolutionary History of Three-Dimensional Basin

ＮＵＭＥＲＩＣＡＬＳＩＭＵＬＡＴＩＯＮＦＯＲＥＶＯＬＵＴＩＯＮＡＲＹＨＩＳＴＯＲＹＯＦＴＨＲＥＥ－ＤＩＭＥＮＳＩＯＮＡＬＢＡＳＩＮＹｕａｎＹｉ－ｒａｎｇ（袁益让）；ＷａｎｇＷｅｎ－ｑｉａ（王文洽）；ＹａｎｇＤａｎ－ｐｉｎｇ（羊丹平）（Ｄｅｐａｒｔｍｅ...     

Numerical Simulation of Diesel Spray Evaporation in a “Stabilized Cool Flame” Reactor: A Comparative Study

The major objective of this work is to numerically investigate the interacting physical and chemical phenomena that characterize the flow in a stabilized cool flame diesel fuel spray evaporation system. A two-phase RANS computational fluid dynamics code has been developed and used to predict the characteristics of the developing turbulent, multiphase, multi-component, reactive flow-field. The code employs a Eulerian–Lagrangian approach, taking into account the mass, momentum, thermal and turbulent energy exchange between the phases. A variety of physical phenomena, such as turbulent dispersion, droplet evaporation, droplet-wall collision, conjugate heat transfer, drift correction, two-way coupling are taken into account by implementing respective sub-models. Two alternative modelling approaches for the simulation of cool flame reactions have been validated and evaluated by comparing numerical predictions with experimental data from two atmospheric pressure, evaporating Diesel spray, Stabilized Cool Flame reactors. Both models have achieved good quantitative agreement in the majority of the considered test cases. The results have been used to estimate the local physical and chemical characteristic time scales of the occurring phenomena, thus allowing, for the first time, the classification of stabilized cool flames.     

Some bounded results of θ(t)-type singular integral operators

Let B be a Banach space in UMD with an unconditional basis. The boundedness of the θ(t)-type singular integral operators in L _B ^p (R ⁿ), (1≤p<+∞) and H _B ¹ (R ⁿ) spaces are discussed. Foundation item: the Education Commission of Shandong Province (J98P51) Biography: Zhao Kai (1960-)     

Experimental study of vortex–structure interaction noise radiated from rod–airfoil configurations

Vortex–structure interaction noise radiated from an airfoil embedded in the wake of a rod is investigated experimentally in an anechoic wind tunnel by means of a phased microphone array for acoustic tests and particle image velocimetry (PIV) for the flow field measurements. The rod–airfoil configuration is varied by changing the rod diameter (D), adjusting the cross-stream position (Y) of the rod and the streamwise gap (L) between the rod and the airfoil leading edge. Two noise control concepts, including “air blowing” on the upstream rod and a soft-vane leading edge on the airfoil, are applied to control the vortex–structure interaction noise. The motivation behind this study is to investigate the effects of the three parameters on the characteristics of the radiated noise and then explore the influences of the noise control concepts. Both the vortex–structure interaction noise and the rod vortex shedding tonal noise are analysed. The acoustic test results show that both the position and magnitude of the dominant noise source of the rod–airfoil model are highly dependent on the parameters considered. In the case where the vortex–structure interaction noise is dominant, the application of the air blowing and the soft vane can effectively attenuate the interaction noise. Flow field measurements suggest that the intensity of the vortex–structure interaction and the flow impingement on the airfoil leading edge are suppressed by the control methods, giving a reduction in noise.     

Simulation of an optically induced asymmetric deformation of a liquid–liquid interface

Deformations of liquid interfaces by the optical radiation pressure of a focused laser wave were generally expected to display similar behavior, whatever the direction of propagation of the incident beam. Recent experiments showed that the invariance of interface deformations with respect to the direction of propagation of the incident wave is broken at high laser intensities. In the case of a beam propagating from the liquid of smaller refractive index to that of larger one, the interface remains stable, forming a nipple-like shape, while for the opposite direction of propagation, an instability occurs, leading to a long needle-like deformation emitting micro-droplets. While an analytical model successfully predicts the equilibrium shape of weakly deformed interface, very few work has been accomplished in the regime of large interface deformations. In this work, we use the Boundary Integral Element Method (BIEM) to compute the evolution of the shape of a fluid–fluid interface under the effect of a continuous laser wave, and we compare our numerical simulations to experimental data in the regime of large deformations for both upward and downward beam propagation. We confirm the invariance breakdown observed experimentally and find good agreement between predicted and experimental interface hump heights below the instability threshold.     

Large Eddy Simulation of a Methane–Air Diffusion Flame

Large Eddy Simulation has been applied to a piloted methane/air diffusion flame—the Sandia D flame—for which detailed experimental data are available. To evaluate the reacting density, temperature and species mass fractions a conserved scalar laminar flamelet formulation is employed, utilising a single virtually unstrained flamelet. The results of two simulations are discussed, comparing the use of the standard Smagorinsky model and a dynamic variant for closure of the unknown sub-grid stress. The chosen sub-grid scale model is shown to be extremely influential on the final solution. Whilst the use of the standard model results in a relatively poor simulation the dynamic closure offers an excellent velocity field prediction throughout the flame. Although the flame does show some strain rate influence on burning, particularly close to the inlet nozzle, the relatively simple ‘unstrained’ flamelet model applied is shown to provide an accurate representation of temperature and major species distribution.     

A C<Superscript>0</Superscript>-type zig–zag theory and finite element for laminated composite and sandwich plates with general configurations

In order to conveniently develop C⁰ continuous element for the accurate analysis of laminated composite and sandwich plates with general configurations, this paper develops a C⁰-type zig–zag theory in which the interlaminar continuity of transverse shear stresses is a priori satisfied and the number of unknowns is independent of the number of layers. The present theory is applicable not only to the cross-ply but also to the angle-ply laminated composite and sandwich plates. On the premise of retaining the merit of previous zig–zag theories, the derivatives of transverse displacement have been taken out from the displacement fields. Therefore, based on the proposed zig–zag theory, it is very easy to construct the C⁰ continuous element. To assess the performance of the proposed model, the classical quadratic six-node triangular element with seven degrees of freedom at each node is presented for the static analysis of laminated composite and sandwich plates. The typical examples are taken into account to assess the performance of finite element based on the proposed zig–zag theory by comparing the present results with the three-dimensional elasticity solutions. Numerical results show that the present model can produce the more accurate deformations and stresses compared with the previous zig–zag theories.     

Simulation of Initially Slackened and Stiffened Structures by Virtual Distortions∗

ABSTRACT

Variational principles and computational methods for analysis of initially slackened and stiffened structures are discussed. The simulation of clearances or internal dry fraction in structural elements by virtual (eigen) distortions is applied. Considerations presented are used in the problem of nonstandard design of structural settings, with clearances or friction in the structural joints, for load capacity maximization.     

Evolution of ion–ion acoustic instability in multi-ion plasma sheaths

Nonlinear Dynamics - The generation of ion-acoustic solitary waves is investigated in a nonuniform multicomponent collisional plasma sheath containing cold ions and Boltzmann electrons to probe the...     

FE analysis of the in-plane mechanical properties of a novel Voronoi-type lattice with positive and negative Poisson’s ratio configurations

This work presents a novel formulation for a Voronoi-type cellular material with in-plane anisotropic behaviour, showing global positive and negative Poisson’s ratio effects under uniaxial tensile loading. The effects of the cell geometry and relative density over the global stiffness, equivalent in-plane Poisson’s ratios and shear modulus of the Voronoi-type structure are evaluated with a parametric analysis. Empirical formulas are identified to reproduce the mechanical trends of the equivalent homogeneous orthotropic material representing the Voronoi-type structure and its geometry parameters.     

Simulation of Wind Flow Around a Building with a k–ε Model

The three-dimensional numerical simulation of airflow around a building using a k–ε two-equation turbulence model is presented in this paper. Several cases of numerical simulation of airflow around a building are carried out to estimate the influence of mesh spacing on simulated results. The accuracy of simulations is examined by comparing the predicted results with wind-tunnel experiments. It is confirmed that numerical simulations by means of the k–ε model reproduce the velocity fields well when using fine mesh resolution. In the latter part of the paper, the simulation method is applied to predict the flow field around a building with different width-to-height ratios, under light wind conditions. Received 16 June 1999 and accepted 20 July 2000     

An Upscaling–Static-Downscaling Scheme for Simulation of Enhanced Oil Recovery Processes

We investigate whether upscaling errors for EOR simulation can be reduced by an upscaling–static-downscaling method where the scales of simulation for the pressure and saturation/concentration switch between coarse simulation model and fine geological model. We apply a static downscaling that has been previously shown to be reliable for water flooding. We use the same algorithm of static downscaling for EOR processes that have been used for water flooding. Different EOR processes are considered: polymer, surfactant and thermal. This range of flooding processes ensures that we are examining more physically complicated systems than water flooding. For these processes, one major difference from water flooding is existence of a secondary front. The effective capturing of this front is a criterion of accuracy for upscaling because, for this front, the coupling of dispersion with the fractional flow creates excessive smearing. A scheme for numerical dispersion control is implemented to both upscaled and downscaled models to determine and reduce the sensitivity to dispersion errors.     

Active cancellation of artificially introduced Tollmien–Schlichting waves using plasma actuators

In the present work artificially excited Tollmien–Schlichting (TS) waves were cancelled using plasma actuators operated in pulsed mode. In order to achieve this a vibrating surface driven by an electromagnetic turbulator was flush mounted in a flat plate to excite the TS waves. These were amplified by an adverse pressure gradient induced by an insert on the upper wall of the test section. A control plasma actuator positioned downstream of the excitation actuator attenuates the waves by imparting an unsteady force into the boundary layer to counteract the oscillation. As a result the amplitude of the velocity fluctuations at the excitation frequency is reduced significantly depending on the distance from the wall. A parameter study was performed to identify the influence of several operation parameters of the control actuator.     

Large Eddy Simulation of Premixed Turbulent Combustion Using Ξ Flame Surface Wrinkling Model

One commonly-used method for deriving the RANS equations for multicomponent flow is the technique of conditional averaging. In this paper the concept is extended to LES, by introducing the operations of conditional filtering and surface filtering. Properties of the filtered indicator function are investigated mathematically and computationally. These techniques are then used to derive conditionally filtered versions of the Navier–Stokes equations which are appropriate for simulating multicomponent flow in LES. Transport equations for the favre-averaged indicator function and the unresolved interface properties (the wrinkling and the surface area per unit volume) are also derived. Since the paper is directed towards modelling premixed combustion in the flamelet regime, closure of the equations is achieved by introducing physical models based on the picture of the flame as a wrinkled surface separating burnt and unburnt components of the fluid. This leads to a set of models for premixed turbulent combustion of varying complexity. The results of applying one of this set of models to propagation of a spherical flame in isotropic homogeneous turbulence are analysed. This revised version was published online in July 2006 with corrections to the Cover Date.     

Simulation of fine polydisperse particle condensational growth under an octadecane–nitrogen atmosphere

The evolution of particle size distribution (PSD) of fine polydisperse particles at high number concentrations (>10⁵ cm⁻³) was simulated through a combined model employing direct quadrature method of moments (DQMOM) with heat and mass transfer equations. The PSD was assumed to retain log-normal distribution during the heterogeneous condensation process. The model was first verified by exact solution and experimental data prior to investigating the influence of initial conditions on final PSD under an octadecane–nitrogen atmosphere. Low particle number concentrations and high vapor concentrations were beneficial to shift the PSD to larger particles having a narrower distribution. Additionally, vapor depletion has more influence on the final PSD than the heat release parameter for a number concentration of 10⁶ cm⁻³. This study may assist the design process of a gas–solid separating cyclone, to eliminate dust from high-temperature volatiles by pyrolysis of solid fuels.     

Simulation and hybrid fuzzy-PID control for positioning of a hydraulic system

Accuracy and precision of position control of hydraulic systems are key parameters for engineering applications in order to set more economical and quality systems. In this context, this paper presents modeling and position control of a hydraulic actuation system consisting of an asymmetric hydraulic cylinder driven by a four way, three position proportional valve. In this system model, the bulk modulus is considered as a variable. In addition, the Hybrid Fuzzy-PID Controller with Coupled Rules (HFPIDCR) is proposed for position control of the hydraulic system and its performance is tested by simulation studies. The novel aspect of this controller is to combine fuzzy logic and PID controllers in terms of a switching condition. Simulation results of the HFPIDCR based controller are compared with the results of classical PID, Fuzzy Logic Controller (FLC), and Hybrid Fuzzy-PID controller (HFPID). As a result, it is demonstrated that Hybrid Fuzzy PID Controller with Coupled Rules is more effective than other controllers.     

Simulation of planar flexible multibody systems with clearance and lubricated revolute joints

Modeling of clearance joints plays an important role in the analysis and design of multibody mechanical systems. Based on the absolute nodal coordinate formulation (ANCF), a new computational methodology for modeling and analysis of planar flexible multibody systems with clearance and lubricated revolute joints is presented. A planar absolute nodal coordinate formulation based on the locking-free shear deformable beam element is implemented to discretize the flexible bodies. A continuous contact-impact model is used to evaluate the contact force, in which energy dissipation in the form of hysteresis damping is considered. A force transition model from hydrodynamic lubrication forces to dry contact forces is introduced to ensure continuity in the joint reaction force. A comprehensive study with different lubrication force models has also been carried out. The generalized-α method is used to solve the equations of motion and several efficient methods are incorporated in the proposed model. Finally, the methodology is validated by two numerical examples.     

Studies of Mental “Noise”

Successive tests of subjects' performance in reaction time tasks were treated as time series and submitted to spectrum analysis. Rather than revealing the white noise expected by the view that variability is due to random error (equivalent power across frequency), the power spectra revealed colored noise. The slopes of the power spectra did not vary much for tasks differing in memory requirements. Spectrum analysis of time series from the logistic map also showed colored noise in regions on the edge of chaos, showing that the presence of colored noise in cognitive data need not oblige a theoretical account based on a complex, high-dimensional, system.