Sinusoidal Steady State Analysis on 4H--SiC Buried Channel MOSFETs

With the combined use of the drift-diffusion （DD） model, experiment measured parameters and small-signal sinusoidM steady-state analysis, we extract the Y-parameters for 4H-SiC buried-channel metal oxide semicon- ductor field effect transistors （BCMOSFETs）. Output short-circuit current gain G and Mason＇s invariant U are cMculated for extrapolating unity current gain frequency in the common-source configuration fT and the maximum frequency of oscillation fmax, respectively. Here fT = 800 MHz and fmax= 5 GHz are extracted for the 4H-SiC BCMOSFETs, while the field effect mobility reaches its peak value 87cm2/Vs when VGs = 4.5 V. Simulation results clearly show that the characteristic frequency of 4H-SiC BCMOSFETs and field effect mobility are superior, due to the novel structure, compared with conventional MOSFETs.     

Ultraviolet Phototransistors on AlGaN/GaN Heterostructures

We report on the fabrication and characterization of phototransistors based on AIGaN/GaN heterostructure grown over 6H-SiC substrates. The device has two functions： as a high electron mobility transistor （HEMT） and an ultraviolet photodetector at the same time. As an HEMT, its maximum transconductance is 170mS/ram, while the minimum cutoff frequency fT and the maximum oscillation frequency fm are 19 and 35 GHz, respectively. As a photodetector, the device is visible blind, with an ultraviolet/green contrast of three orders of magnitude, and a responsivity as high as 1700 A/W at the wavelength of 362nm.     

Indentation Load Effect on Young＇s Modulus and Hardness of Porous Sialon Ceramic by Depth Sensing Indentation Tests

Depth sensing indentation （DSI） tests at the range of 200-1800mN are performed on porous sialon ceramic to determine the indentation load on Young＇s modulus and hardness values. The Young modulus and hardness （Dynamic and Martens） values are deduced by analysing the unloading segments of the DSI test load-displacement curves using the Oliver-Pharr method. It is found that Young＇s modulus ET, the dynamic hardness HD and the Martens hardness HM exhibit significant indentation load dependences. The values of Young＇s modulus and hardness decrease with the increasing indentation load, as a result of indentation load effect. The experimental hf /hm ratios lower than the critical value 0.7, with hm being the maximum penetration depth during loading and hf the final unloading depth, indicate that our sample shows the work hardening behaviour.     

Overshooting and Prescission Neutron Multiplicity in Nuclear Fission

The transient behavior in approaching to quasi-stationary state for fissioning systems is studied by diffusion model.It is shown that there are two regions:Kramers region for Tf and overshooting region for T>E_f according to the transient behavior of probability current.A particular attention is paid to the overshooting region because it tends to decrease the enhancement effect of neutron multiplicity and even leads to its disappearance.However it has been proved that the enhancement of neutron multiplicity results from the transient behavior in fission process.     

Efficient White Light Emission Using a Single Copolymer with Red and Green Chromophores on a Conjugated Polyfluorene Backbone Hybridized with InGaN-Based Light-Emitting Diodes

We report an efficient white-light emission based on a single copolymer/InGaN hybrid light-emitting diode. The single copolymer consists of a conjugated polyfluorene backbone by incorporating 2,1,3-benzothiadiazole （BT） and 4,7-bis（2-thienyl）-2,1,3-benzothiadiazole （DBT） as green and red light-emitting units, respectively. For the single copolymer/InGaN hybrid device, the Commission Internationale de 1＇Eclairage （CIE） coordinates, color temperature Tc and color rendering index Ra at 20mA are （0.323,0.329）, 5960K and 86, respectively. In comparison with the performance of red eopolymer PFO-DBT15 （DOF：DBT=85：15 with DOF being 9＇9- dioctylfluorene） and green copolymer PFO-BT35 （DOF：BT=-65：35） blend/InGaN hybrid white devices, it is concluded that the chemically doped copolymer hybridized device shows a higher emission intensity and spectral stability at a high driving current than the polymer blend.     

A Power Interruption Technique for Investigation of Temperature Difference in Stabilized Low Direct-Current Arc Burning in Pure Argon on Atmospheric Pressure

Plasma of argon stabilized arc column, in a current range 3-11 A, is investigated using emission spectrometric diagnostic techniques. Temperatures are evaluated using several methods： argon line to adjacent recombinational continuum intensity ratio, absolute emissivity of argon line, measurement of electron number density, and power interruption. Electron number density is evaluated from absolute emissivity of recombinational continuum. The difference between electron Te and heavy particle Th temperature ranged from 4500 K for 3 A to 2300 K for 11A arc current. By comparing the present with the previously obtained results, using the same arc device but with the introduction of water aerosol, it is concluded that water aerosol reduces the difference Te - Th and brings plasma closer to the partial thermodynamic equilibrium state.     

Dielectronic Recombination of Sn^10＋ Ions and Related Satellite Spectra

Based on the multi-configuration Dirac-Fock method, theoretical calculations are carried out for the dielectronic recombination （DR） rate coefficients and the collision excitation rate coefficients of Sn^10＋ ions. It is found that the total DR rate coefficient has its maximum value between 10eV and 100eV and is greater than either the radiative recombination or three-body recombination rate coefficients （the number of free electrons per unit is 10^21 cm^3） for the ease of Te 〉 1 eV. Therefore, DR can strongly influence the ionization balance of laser produced multi-charged tin ions. The related dieleetronie satellite cannot be ignored at low temperature Te 〈 5 eV.     

Enhanced Magnetoresistance of （La0.67Ca0.33MnO3） Composites Coated by Zn0.95Co0.05O

La0.7Ca0.3MnO3：xZn0.95Co0.05O （x=0.0,0.05, 0.1, 0.15mol） composites are prepared by a sol-gel process. X- ray diffraction and energy diffraction spectroscopy reveal that there is no evidence of a reaction between the La0.7 Ca0.3 MnO3 （LCMO） and Zn0.95Co0.05 O （ZCO）. Magnetization M, Curie temperature Tc and metal-insulator transition temperatures Tp are observed to decrease with increasing ZCO content. Compared with x = 0.0, a great enhancement in the magnetoresistance （MR） is observed at around Tc for x = 0.05, 0.10, 0.15. Based on the tunneling MR and percolation models, this great change of MR is well explained.     

Diagnostics of laser-ablated carbon plumes by photoionization using a tunable laser

Tunable laser pulses at wavelengths from 250 to 880 nm were fired at plumes produced by laser ablation of a carbon target in He atmosphere. We observed an electrical current due to photoionization, which roughly reflected the behavior of carbon clusters in the plume. The photoionization current had dynamic temporal variations, comprising a rapid increase at the beginning (T_D<0.2 ms, where T_D is the time after a YAG laser pulse for laser ablation irradiates the target), a gradual increase for 0.2D<3 ms, and a slow decrease for T_D>7 ms. The increasing phase of the photoionization current was synchronized with the decreasing phase of C₂ radical density. For He gas pressures lower than 0.8 Torr no photoionization current was detected. The growth rate of the photoionization current was higher for a higher He gas pressure.     

Polarized Micro-Raman Study of the Temperature-Induced Phase Transition In 0.67 Pb（Mg1/3Nb2/3）O3-0.33PbTiO3

Polarized Raman spectra of ferroelectric relaxor 0.67Pb（Mg1/3Nb2/3）O3-0.33PbTiO3 （0.67PMN-0.33PT） single crystal are systematically investigated in a wide temperature range from -196 to 600℃ by micro-Raman scattering technique. The results clearly reveal that there are two structural phase transitions in such composite ferroelectric relaxor： the rhombohedral-tetragonal （R- T） phase transition and the tetragonal-cubic （T- C） phase transition. The former occurs at about TR-T =34℃, corresponding to the vanishing of the soft A1 mode at 106cm^-1 recorded in the parallel polarization. The latter appears at about TT-C = 144℃, which can be verified with the vanishing of mode at 780cm^-1 measured in the crossed polarization.     

Gauss-Bonnet and Lovelock Gravities and the Generalized Second Law of Thermodynamics

It has been shown [Chin. Phys. Lett.25 （2008） 4199] that the generalized second law of thermodynamics holds in Einstein gravity. Here we extend this procedure for Gauss-Bonnet and Lovelock gravities. It is shown that by employing the general expression for temperature Th =｜κ｜/2π= 1/2πτA （1-τA/2HτA） associated with the apparent horizon of a Friedman Robertson-Walker （FRW） universe and assuming Tm = bTh, we are able to construct conditions for which the generalized second law holds in Gauss Bonnet and Lovelock gravities, where Tm and Th are the temperatures of the source and the horizon respectively.     

Contribution from the Earth's Bow Shock to Region 1 Current under Low Alfvén Mach Numbers

Using global MHD simulations of the solar wind-magnetosphere-ionosphere system, we investigate the dependence of the contribution from the Earth's bow shock (I_1bs) to ionospheric region 1 field aligned current (FAC) (I₁). It is found that I_1bs increases with increasing southward interplanetary magnetic field (IMF) strength B_s, if the Alfvén Mach number M_A of the solar wind exceeds 2, a similar result as obtained by previous authors. However, if M_A becomes close to or falls below 2, I_1bs will decrease with B_s in both magnitude and percentage (i.e., I_1bs}/I₁) because of the resultant reduction of the bow shock strength. Both the surface current density J_bs at the nose of the bow shock and the total bow shock current I_bs share nearly the same relationship with M_A, and vary non-monotonically with M_A or B_s. The maximum point is found to be located at M_A = 2.7. Three conclusions are then made as follows: (1) The surface current density at the nose, which is much easier to be evaluated, may be used to largely describe the behaviour of the bow shock instead of the total bow shock current. (2) The peak of the total bow shock current is reached at about M_A = 2.7 when only B_s is adjusted. (3) The non-monotonic variation of the bow shock current with M_A causes a similar variation of its contribution to region 1 FAC. The turning point for such contribution is found to be nearly M_A= 2. The implication of these conclusions to the saturation of the ionospheric transpolar potential is briefly discussed     

Improvement of Field Emission Characteristics of Copper Nitride Films with Increasing Copper Content

A copper nitride （Cu3N） thin film is deposited on a Si substrate by the reactive magnetron sputtering method. The XPS measurements of the composite film indicate that the Cu content in the film is increased to 80.82 at. % and the value of the Cu/N ratio to 4.2：1 by introducing 4% 112 into the reactive gas. X-ray diffraction measurements show that the film is composed of Cu3N crystallites with an anti-ReO3 structure. The effects of the increase of copper content on the field emission characteristics of the Cu3N thin film are investigated. Significant improvement in emission current density and emission repeatability could be attributed to the geometric field enhancement, caused by numerous surface nanotips, and the decrease of resistivity of the film.     

Enhanced Efficiency of Polymer： Fullerene Bulk Heterojunction Solar Cells with the Insertion of Thin TiO2 Layer near the LiF/A1 Electrode

The insertion layer of TiO2 between polymer-fullerene blend and LiF/AI electrode is used to enhance the shortcircuit current Isc and fill factor （FF）. The solar cell based on the blend of poly[2-methoxy-5-（2＇-ethylhexyloxy）- 1,4-phenylenevinylene] （MEH-PPV） and C60 with the modifying layer of TiO2 （about 20nm） shows the open- circuit Voc of about 0.62 V, short circuit current Isc of about 2.35 mA/cm^2, filling factor FF of about 0.284, and the power conversion efficiency （PCE） of about 2.4% under monochromatic light （50Onto） photoexcitation of about 17mW/cm^2. Compared to ceils without the TiO2 layer, the power conversion efficiency increases by about 17.5%. Similar effect is also obtained in cells with the undoped MEH-PPV structure of ITO/PEDOT：PASS/MEH- PPV/（TiO2）LiF/AI. The improved solar cell performance can be attributed to enhanced carrier extraction efficiency at the active layer/electrode interfaces when TiO2 is inserted.     

非晶La80Al20晶化相的超导电性

 本文把非晶La₈₀Al₂₀在真空中、不同温度及其时间条件下进行退火，以及在6 GPa不同温度退火40 min，并对退火样品的相结构及超导性进行了研究。发现真空中，250 ℃退火的样品晶化成了T>4.2 K、不超导的单相四方La₄Al；300 ℃及450 ℃退火的样品晶化成La₃Al、α-La、β-La及一些未知杂相，这些多相混合物的T_C<6.0 K。在6 GPa 300 ℃及以下温度退火的样品，晶化成单相六角La₄Al，其晶格常数与六角La₃Al的完全相同，这些样品的T_C>5.1 K；6 GPa、350 ℃及以上温度退火的样品，晶化成La₃Al相及新未知相H，新相H的T_C约为6.3 K。     

Improved Performance of Organic Thin Film Transistor with an Inorganic Oxide/Polymer Double-Layer Insulator

We employ the Ta2Os/PVP （poly-4-vinylphenol） double-layer gate insulator to improve the performance of pentacene thin-film transistors. It is found that the double-layer insulator has low leakage current, smooth surface and considerably high capacitance. Compared to Ta205 insulator layers, the device with the Ta2Os/PVP doublelayer insulator exhibits an enhancement of the field-effect mobility from 0.21 to 0.54 cm2/Vs, and the decreasing threshold voltage from 4.38 V to -2.5 V. The results suggest that the Ta2Os/PVP double-layer insulator is a potential gate insulator for fabricating OTFTs with good electrical performance.     

高压熔化曲线的实验标定

 利用Al、Cu、Pb的冲击熔化实验结果,并考虑到材料的Grüneisen系数γ(ρ)从固态值向液态值过渡,通过Lindemann熔化定律标定了熔化曲线T_m(ρ)。由于Lindemann定律与Grüneisen系数γ(ρ)密切相关,因此用冲击熔化实验标定T_m(ρ),也间接标定了γ(ρ)。     

Reactive Ion Etching as Cleaning Method Post Chemical Mechanical Polishing for Phase Change Memory Device

In order to improve nano-scale phase change memory performance, a super-clean interface should be obtained after chemical mechanical polishing （CMP） of Ge2Sb2Te5 phase change films. We use reactive ion etching （RIE） as the cleaning method. The cleaning effect is analysed by scanning electron microscopy and an energy dispersive spectrometer. The results show that particle residue on the surface has been removed. Meanwhile, Ge2Sb2Te5 material stoichiometric content ratios are unchanged. After the top electrode is deposited, currentvoltage characteristics test demonstrates that the set threshold voltage is reduced from 13 V to 2.7V and the threshold current from 0.1 mA to 0.025 mA. Furthermore, we analyse the RIE cleaning principle and compare it with the ultrasonic method.     

New realization of Chua's circuit and verification of chaos by harmonic balance analysis

Chua's circuit, which consists of two capacitors, one inductor, two resistors, one linear voltage-controlled voltage source (VCVS) and voltage-controlled current source (VCCS) type non-linear element has been realized by operational amplifiers. Various dynamical phenomena such as periodic orbit with periods T, 2T, and 4T, single scroll and double scroll similar to the Lorenz attractor have been observed experimentally by changing only the resistance value of the linear resistor R₆. The experimental observations have been confirmed by computer simulations and also using harmonic balance analysis.     

Chiral Lagrangian Treatment of 0^＋＋ Mesons and 0^＋＋ Glueballs

Within the framework of a nonlinear chiral Lagrangian the mass spectra and the decay properties of 0^＋＋ states below 2 GeV are studied. Assuming that f0（980）, a0（980）, K0（1430）, and f0（1500） comprise an SU（3） nonet, we make a detailed prediction about the static properties of the 0^＋＋ mesons. The substructure analysis of these states in terms of two- and four-quark components as well as a glueball component is carried out. We also consider the interaction Lagrangian and provide a preliminary study of the strong and radiative decays of the 0＋＋ mesons. The scalar glueball masses and partial widths are also presented. In view of the fact that few data of 0＋＋ mesons are clearly given in the present PDG （Particle Data Group） list and that the four-quark content of mesons is a hot issue both experimentally and theoretically, the predicted results of the paper may be helpful for upcoming experimental and theoretical studies of these mesons.