Chain-folding measurements in annealed poly(ethylene terephthalate)

Chain folding in unoriented poly(ethylene terephthalate) (PET) films has been investigated as a function of annealing time and temperature. To meet this objective dynamic mechanical, infrared, and molecular weight measurements were used, together with selective chemical degradation to remove chain folds and amorphous regions. The β dispersion in the dynamic mechanical spectrum of PET is here tentatively associated with motions of methylene and/or carboxyl groups in irregular chain folds; the β dispersion is not found in quenched amorphous polymer, in polymer where amorphous regions and chain folds have been removed, or in highly annealed PET where the irregular folds have regularized. Upon mild crystallization and annealing (30 min at 110°C) of initially amorphous film a large β dispersion appears and then diminishes upon further annealing at 220°C. As the β dispersion diminishes, the infrared regular fold band increases more than the crystallinity band, indicating regularization of folds. The molecular weight of the degraded residue corresponds approximately to typical fold-period dimensions (～130 Å), and increases on annealing as expected from lamellar thickening. The degradation process has, by fold removal, reduced the chains in the crystals to a very short, uniform length.     

Study of crystallinity and thermomechanical analysis of annealed poly(ethylene terephthalate) films

The objective of this article was the determination of the degree of crystallinity of a series of heat-set poly(ethylene terephthalate) (PET) films and their study by thermomechanical analysis (TMA) in order to elucidate a peculiar behaviour that takes place around the glass transition region. For this purpose, amorphous cast Mylar films from DuPont were annealed at 115 °C for various periods of time. Four methods were used to study the crystallinity of the samples prepared: differential scanning calorimetry (DSC), density measurements (DM), wide-angle X-ray diffraction (WAXD), and Fourier transform infrared spectroscopy (FT-IR). From the results obtained, the following conclusions are drawn: amorphous PET Mylar films can be crystallized in a degree of about up to 30% after thermal treatment for 30 min (cold crystallization) above glass transition temperature. When these semicrystalline samples are subjected to TMA, they show a two step penetration of the probe into them, which decreases with the increase of the degree of crystallinity. The first step of penetration was attributed to the shrinkage of the amorphous or semicrystalline sample, which takes place on the glass transition temperature, while the second step was attributed to the continuous softening of the sample, and the reorganization of the matter which takes place on heating run due to cold crystallization.     

Alternating copolymers of tetramethylene urea with 2,2-dimethyltrimethylene carbonate and ethylene carbonate; preparation of the corresponding polyurethanes

Copolymerization of tetramethylene urea (TeU, 1 ) with the cyclic carbonates 2,2-dimethyltrimethylene carbonate (DTC, 2 ) and ethylene carbonate (EC, 3 ) results in the polyurethanes 4 and 5 with an approximate number-average molecular weight of 20 000 and a polydispersity index of two. Polyurethane 4 is an amorphous material with a glass transition temperature of 26.3°C; polyurethane 5 is a semicrystalline material with a melting temperature of 208°C. Distinct copolymerization mechanisms are proposed for the formation of polyurethane 4 and 5 , respectively.     

The brittle–ductile transition induced by thermal ageing of toluene cast poly(2,6‐dimethyl‐1,4‐phenylene oxide) as observed by interfacial friction

The interfacial shear stress of toluene cast poly(2,6‐dimethyl‐1,4‐phenylene oxide) films has been studied as a function of annealing temperature. The surface topography of these films was studied by scanning probe microscopy following a single sliding pass. Casting from toluene results in a semicrystalline film with a rigid amorphous phase and containing a small amount of residual solvent that exhibits a higher interfacial shear stress than a high temperature annealed solvent‐free amorphous film. Films containing small amounts of toluene exhibit a wear pattern consisting of ripples oriented perpendicular to the sliding direction following a single sliding pass. These results support the notion that the interfacial shear stress is a function of the shear yield stress, and, that during sliding friction tensile stresses must form at the polymer surface. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1637–1643, 2009     

The effect of flexibility on the photodegradation of aromatic diisocyanate-based polyurethanes

The photolytic degradation of 2,4-TDI/aliphatic diol polyurethanes is directly dependent on the flexibility of the polymer backbone. The extent of photodegradation is accelerated above the glass transition temperature, indicating the role of chain flexibility and/or oxygen diffusion in the decomposition process. Photolysis of the model compound ethyl N-phenylcarbamate (EPC) in neutral host polymer matrices indicates that the para photo-Fries to ortho photo-Fries product ratio experiences an accelerated increase with temperature above the glass transition of the polymer matrix.     

Surface interpenetrating networks of polyacrylamide in poly(ethylene terephthalate) as a means of surface modification

Surface interpenetrating network (IPN) polymers are emerging hybrid materials in which the surface of existing polymers can be modified to preserve their chemical structure and bulk properties. A detailed structural characterization of poly(ethylene terephthalate) (PET) thin films on nanoscopically flat silicon wafers has been carried out by Scanning Probe Microscopy (SPM) and X-ray photoelectron spectroscopy (XPS). Examination of the surface of spin-coated annealed PET film by the SPM in tapping mode revealed a two-phase structure. One phase appeared as a dense crystalline fraction of the polymer while the other was identified as amorphous. These findings were supported by Differential Scanning Calorimetry (DSC), which recognized the crystallinity of annealed PET film at 30%. Modification of the PET surface with interpenetrating polyacrylamide (PAM) increased the roughness of the surface with uniform properties. The depth profiling with XPS revealed that PAM interpenetration extended down to 7.2 nm, confirming a three-dimensional character of the polymer modification, with a relative mass concentration of PAM at about 30.7% in the IPN interface.     

Polyurethanes from polyols obtained by ADMET polymerization of a castor oil‐based diene: Characterization and shape memory properties

The acyclic diene metathesis polymerization (ADMET) of 1,3‐di‐10‐undecenoxy‐2‐propanol, a castor oil based diene, is reported. 10‐Undecenol was used as renewable comonomer to end‐cap polymer chains and limit the molecular weight. The poly ols obtained in this way were reacted with 4,4′‐methylenebis(phenylisocyanate) (MDI) to yield a series of amorphous and semicrystalline polyurethane networks. The thermal stability and the thermomechanical and mechanical properties of these thermosets have been studied and showed good shape memory properties for the semicrystalline polymer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Solid-state coextrusion of poly(ethylene terephthalate). II. Drawing of semicrystalline PET

The drawing of semicrystalline (33 and 50%) poly(ethylene terephthalate) (PET) films has been studied by solid-state coextrusion. Because of its brittleness and opacity, isotropic and semicrystalline PET film is of little practical use. Early attempts to cold-draw crystalline films led to fracture in contrast to deformation of amorphous PET. However, we have succeeded in systematically preparing films with extrusion draw ratios ≤4.4 from semicrystalline PET. In many cases, the properties of the drawn extrudates, as a function of extrusion temperature T_ext and extrusion draw ratio EDR, were similar to those prepared from amorphous PET. However, some remarkable differences have also been found. In the case of coextrudates prepared from isotropic 50% crystalline PET, we found that the larger the deformation, the lower the apparent resulting crystallinity. In the extreme, a 34% reduction in crystallinity after deformation was observed. For the coextrudates drawn from initially 33% crystalline PET, slightly different behavior occurred. For T_ext ≤ 90°C, all extrudates showed crystallinities lower than the original isotropic film, with a minimum at EDR = 3; for T_ext ≥ 110°C, crystallinities were slightly greater than in the original film and increased with EDR. Qualitative measurements of heats of fusion were in agreement with density gradient results for PET crystallinity. In contrast is our previous finding that extrudates from initially amorphous PET always increase in crystallinity with EDR, because of stress-induced crystallization. The results now suggest that in the T_ext range investigated, the initial spherulitic structure is at least in part destroyed on drawing. In addition, the percent crystallinity is revealed to be dependent on T_ext, with lower values at lower temperatures. Mechanical tests show that the extrudates are similar or sometimes higher in tensile modulus when compared to amorphous PET drawn under the same conditions.     

Studies on surface structures of poly(ethylene oxide)‐segmented nylon films

The surface structures of three kinds of poly(ethylene oxide)‐segmented nylon (PEO‐Ny) molten films were investigated using a scanning electron microscopy (SEM), an electron spectroscopy for a chemical analysis (ESCA), and a static secondary ion mass spectrometry (SSIMS). The PEO‐Ny's used were high semicrystalline PEO‐segmented poly(iminosebacoyliminohexamethylene) (PEO‐Ny610), low semicrystalline PEO‐segmented poly(iminosebacoylimino‐m‐xylene) (PEO‐NyM10), and amorphous PEO‐segmented poly(iminoisophthaloyliminomethylene‐1,3‐cyclohexylenemethylene) (PEO‐NyBI). SEM observations show that the surfaces of the PEO‐Ny610 and PEO‐NyM10 films are composed of spherulite, and that PEO‐NyBI film has a smooth surface. The results of ESCA and SSIMS exhibit the significant enrichments of PEO segment at the surfaces of all the films regardless of the crystallinity. The reason for the enrichment of PEO segment was discussed in terms of the surface tension of the corresponding homopolymers in the melting state. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1045–1056, 2000     

Photolysis of aromatic diisocyanate-based polyurethanes in solution

Fluorescence analysis has been employed as an analytical technique to elucidate the photolysis mechanism of several aromatic diisocyanate-based polyurethanes in solution. Based on a comparison with model arylmonocarbamates and arylbiscarbamates, the photo-Fries rearrangement and cleavage-type products found for the small-model arylcarbamates were also identified for the photolyzed polyurethanes in solution. Viscosity and absorbance change results for photolysis of both air and nitrogen-saturated polyurethane solutions are consistent with a general two-step mechanism for the photolysis of aromatic diisocyanate-based polyurethanes.     

旋涂水溶液前驱体制备氧化锌薄膜及其性质

通过旋涂法, 采用Zn(OAc)2·2H2O和聚环氧乙烷(PEO)的水溶液为前驱体在不同的热处理温度下制备了ZnO薄膜. PEO的加入增加了溶液的成膜性, 其较低的热分解温度有利于制得纯净的ZnO薄膜. 文中考察了在不同热处理温度下制备的ZnO薄膜的形貌、结晶性、带隙(Eg)以及电导性. 原子力显微镜(AFM)测试表明在热处理温度为400、450和500 ℃制备的ZnO薄膜的粗糙度均方根值分别为3.3、2.7和3.6 nm. 采用透射电子显微镜(TEM)测试发现ZnO薄膜中含有大量纳晶粒子. 通过测试ZnO薄膜的UV-Vis吸收光谱, 根据薄膜位于373 nm处的吸收带边计算得到ZnO的带隙为3.3 eV. 通过对薄膜的电流-电压(I-V)曲线的测试计算得到在热处理温度为400、450和500 ℃制备的ZnO薄膜的电阻率分别为3.3×109、2.7×109和6.6×109 Ω·cm. 450 ℃时制备的ZnO薄膜的电阻率最小, 主要是由于较高的热处理温度有利于提高薄膜的纯度、密度和吸附氧. 而纯度较高、密度较大的薄膜电阻率比较小; 吸附氧含量增加, 晶界势垒增大, 电阻率增大. 因此在纯度和吸附氧的双重作用下450 ℃时制备的ZnO薄膜的电阻率最小, 而500 ℃时制备的ZnO薄膜的电阻率最大.     

Light olefins/paraffins sorption in poly(lactic acid) films

The sorption behavior of small molecules like ethane and ethylene in poly (lactic acid) (PLA) was studied in the temperature interval from 283 to 313 K using a Quartz Crystal Microbalance (QCM). The effect of the polymer structure on the solubility selectivity of PLA films with respect to these two gases was studied using polymer with two different L:D ratios (98:2 and 80:20). Furthermore, the polymer films were submitted to different thermal treatments to address the influence of crystallinity and morphology of the noncrystalline fraction on the sorption behavior. The sorption results obtained indicate that ethylene solubility coefficient in annealed PLA 98:2 is about 26% higher than that of ethane and 41% higher in PLA 98:2 melted. The dual‐mode sorption model describes well the sorption isotherms behavior, which is concave concerning the pressure axis. The fully amorphous PLA presents the better selectivity for the studied gases, since the crystallinity seems to produce a negative effect on the selectivity. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1312–1319, 2008     

Assessment and formation mechanism of laser-induced periodic surface structures on polymer spin-coated films in real and reciprocal space

In this work we evaluate the potential of grazing incidence X-ray scattering techniques in the investigation of laser-induced periodic surface structures (LIPSSs) in a series of strongly absorbing model spin-coated polymer films which are amorphous, such as poly(ethylene terephthalate), poly(trimethylene terephthalate), and poly(carbonate bisphenol A), and in a weaker absorbing polymer, such as semicrystalline poly(vinylidene fluoride), over a narrow range of fluences. Irradiation was performed with pulses of 6 ns at 266 nm, and LIPSSs with period lengths similar to the laser wavelength and parallel to the laser polarization direction are formed by devitrification of the film surface at temperatures above the characteristic glass transition temperature of the polymers. No crystallization of the surface is induced by laser irradiation, and crystallinity of the material prevents LIPSS formation. The structural information obtained by both atomic force microscopy and grazing incidence small-angle X-ray scattering (GISAXS) correlates satisfactorily. Comparison of experimental and simulated GISAXS patterns suggests that LIPSSs can be well described considering a quasi-one-dimensional paracrystalline lattice and that irradiation parameters have an influence on the order of such a lattice.     

Synthesis and ESCA surface studies of octadecyl chain-extended polyurethanes

Poly(ether urethane)s as biomaterials display certain favorable mechanical and biocompatibility properties. Earlier studies suggest that improved blood compatibility might be attained by introducing hydrocarbon groups at the surface. We synthesized and characterized a series of polyurethanes in which a N-2,3-dihydroxypropyl-N′-octadecyl urea chain extender (ODCE) was incorporated into the poly(tetramethylene glycol) (PTMO)/4,4′-methylenebis(phenylene isocyanate) (MDI) system. Molecular weights of the polymers varied between 40,000 and 250,000. An electron spectroscopy for chemical analysis (ESCA) study of the ODCE polyurethane surface revealed a substantially enhanced hydrocarbon concentration compared to a control PTMO/MDI/ethylene diamine (ED) polyurethane surface. Also, bulk composition analyses and ESCA data of the ODCE polymers indicated that the percentage of carbon was higher in the surface region than in the bulk. Thus, the ODCE polymer showed a marked increase in hard-segment concentration in the surface region compared to the bulk region and to the ED polymer.     

Aging and degradation of polyolefins. III. Polyethylene and ethylene–propylene copolymers

Rates of oxygen absorption and formation of oxidation products were determined in γ-initiated oxidations of thin films of high- and low-density polyethylene, atactic and isotactic polypropylene, and of three ethylene–propylene copolymers. Radiation yields G for O₂ absorbed and formation of hydroperoxides depend on dose rates and decrease sharply with increasing ethylene content of the copolymers and moderately with increasing crystallinity of any base polymer. G values for dialkyl peroxide and carbonyl formation, and therefore for chain initiation and termination, do not change much with polymer composition and crystallinity and not at all with dose rates. A few experiments with atactic polypropylene and an amorphous ethylene–propylene copolymer, initiated by di-tert-butylperoxy oxalate, indicate that 37 mole-% of ethylene in the polymer increases the efficiency of initiation and the tendency toward crosslinking.     

Synthesis and characterization of poly(urethane-sulfone)s

Eight poly(urethane-sulfone)s were synthesized from two sulfone-containing diols, 1,3-bis(3-hydroxypropylsulfonyl)propane (Diol-333) and 1,4-bis(3-hydroxypropylsulfonyl)butane (Diol-343), and three diisocyanates, 1,6-hexamethylene diisocyanate (HMDI), 4,4′-diphenylmethane diisocyanate (MDI), and tolylene diisocyanate (TDI, 2,4- 80%; 2,6-20%). As a comparison, eight polyurethanes were also synthesized from two alkanediols, 1,9-nonanediol and 1,10-decanediol, and three diisocyanates. Diol-333 and Diol-343 were prepared by the addition of 1,3-propanedithiol or 1,4-butanedithiol to allyl alcohol and subsequent oxidation of the resulting sulfide-containing diols. The homopoly(urethanesulfone)s from HMDI and MDI are semicrystalline, and are soluble in m-cresol and hot DMF, DMAC, and DMSO. The copoly(urethane-sulfone)s from a 1/1 molar ratio mixture of Diol-333 and Diol-343 with HMDI or MDI have lower crystallinity and better solubility than the corresponding homopoly(urethane-sulfone)s. The poly(urethane-sulfone)s from TDI are amorphous, and are readily soluble in m-cresol, DMF, DMAC, and DMSO at room temperature. Differential scanning calorimetry data showed that poly(urethane-sulfone)s have higher glass transition temperatures and melting points than the corresponding polyurethanes without sulfone groups. The rise in glass transition temperature is 20–25°C while the rise in melting temperature is 46–71°C. © 1994 John Wiley & Sons, Inc.     

Polycaprolactone based biodegradable polyurethanes

Two series of segmented polyurethanes were prepared with systematic variation in soft and hard segment length. The soft segment was constituted by polycaprolactone (PCL) blocks of molecular masses 530 or 2000 and the hard segment (HS) by urethane blocks, in a concentration that varied from 12% to 44% in weight of the whole polyurethane. Morphological analyses indicated that the amount of crystallinity of copolymers was strongly dependent on the PCL molar mass and hard segment content. The copolymers with longer PCL soft segments (Mn=2000) were semicrystalline, but those with shorter PCL segment (Mn=530) were unable to crystallize. The primary factor affectingthe biodegradability of copolymers as evaluated by Sturm tests was the extent of the phase separation, and that the segmental blending of the less biodegradable polyurethane (HS) blocks with PCL in the amorphous phase had a critical unfavorable consequence, which may be attributed to the size of the accessible area by microorganisms.     

Crystal growth rate in ultrathin films of poly(ethylene oxide)

Many dynamical properties of polymers, including segmental relaxation and chain diffusion, exhibit anomalies in thin‐film samples. We extend the studies of thin‐film dynamics to the case of semicrystalline polymers and present a study of the crystal growth rate for thin films of poly(ethylene oxide). We used optical microscopy and quartz crystal microbalance techniques to characterize the kinetics of crystallization for films with thicknesses from 40 to 1000 nm for a range of temperatures near the melting point. A remarkable slowing down of the crystal growth is observed at all temperatures studied for films with a thickness of less than ～100 nm. The results can be used to suggest reductions of the mobility of chains at the crystal/amorphous interface. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2615–2621, 2001     

Model hard segments from diphenyl methane diisocyanate and different chain extenders,and corresponding linear block polyurethanes

Model hard segments from MDI and different chain extenders have been studied by DSC. Among the studied α-ω alkane diol-type chain extenders, all giving crystalline hard segments, butane diol shows the highest melting temperature, while other types such as 1,4-diaminobutane, 1,4-benzene dimethanol, and 4,4′-methylene-bis(2-chloroaniline), so-called MOCA, have no melting endotherm in the range 30–260°C. In addition to DSC, dynamic mechanical properties were measured on linear block polyurethanes having both hard segments and soft ones of hydrogenated 1,2-polybutadiene. The hard segments in the polyurethane chains are of amorphous structure or low crystallinity, and their high-temperature behavior depends only on their strength of interaction in the amorphous state. Accordingly, MOCA shows the highest hard-block softening temperature.     

软段结构对聚氨酯性能影响的研究

用熔融缩聚法俣成了己二酸系和己二酸／芳香二酸混合系两个系列的聚酯；同溶液一步法将部分聚酯与ＭＤＩ反应，形成一系列聚酯型氨酯，以化学分析，ＶＰＯ，ＩＲ，ＤＳＣ，ＷＡＸＤ，力学拉伸等手段对聚酯和聚氨酯进行了表征；讨论了软段聚酯的结构对聚氨酯的结晶性，耐热性，粘结性等性能的影响。