Studies on short isora fibre-reinforced polyester composites

This paper reports the use of a natural fibre, isora, as reinforcement in unsaturated polyester resin. Isora is a bast fibre separated from the bark of Helicteres isora plant by retting process. Properties like tensile strength, flexural strength etc. have been studied as a function of fibre length and fibre loading using treated and untreated fibre. The mechanical properties were found to be optimum at a fibre length of 30 mm and a fibre loading of 30% by volume. The effects of alkali treatment on the fibre properties were investigated by SEM, IR and TGA. The mechanical performance of the treated isora fibre-reinforced polyester composites has also been investigated. SEM studies were carried out to investigate the fibre surface morphology, fibre pull-out and fibre–polyester interface bonding. SEM gave evidence for the changes that had occurred on the fibre surface during chemical treatment. The properties were found to be superior for the composite reinforced with treated fibre compared to the untreated fibre.     

An application of Kozeny–Carman flow resistivity model to predict the acoustical properties of polyester fibre

Modelling of the acoustical properties of polyester fibre materials is usually based on variations of the Bies and Hansen empirical model [1], which allows the calculation of the air flow resistivity of a porous material. The flow resistivity is the key non-acoustical parameter which determines the ability of this kind of materials to absorb sound. The main scope of this work is to illustrate that an alternative theoretical model based on the Kozeny–Carman equation can be used to predict more accurately the flow resistivity from the fibre diameter and bulk material density data. In this paper the flow resistivity is retrieved from the acoustic absorption coefficient data for polyester fibre samples of different densities and fibre diameters. These data agree closely with the flow resistivity predicted with the proposed Kozeny–Carman model.     

Weibull analysis of microbond shear strength at sisal fibre–polyester resin interfaces

An analysis has been made of the tensile strength of sisal fibres and the interfacial adhesion between fibres and polyester resin droplets. Density and microscopy methods were used to determine the cross-sectional area of the sisal fibres. The average tensile strength of treated sisal fibres decreased by a modest amount following treatment with 0.06 M NaOH. However, this treatment resulted in a substantial increase in the interfacial shear strength at the sisal fibre to polyester resin interface. Weibull analysis has been used successfully to analyse variability in tensile strengths and interfacial shear strength using probability of failure plots. Scanning electron microscopy has revealed the shape of resin droplets on the surface of treated and untreated sisal fibres and contact angles are much lower for droplets on treated fibres. Damage to the surface of fibres has been examined following shear testing. Weibull analysis is an effective tool for characterising highly variable fibre properties and evaluating the level of adhesion between polymer resin and the fibre surface.     

Mechanical properties of ZnO nanowires

Semiconductor nanowires are unique as functional building blocks in nanoscale electrical and electromechanical devices. Here, we report on the mechanical properties of ZnO nanowires that range in diameter from 18 to 304 nm. We demonstrate that in contrast to recent reports, Young's modulus is essentially independent of diameter and close to the bulk value, whereas the ultimate strength increases for small diameter wires, and exhibits values up to 40 times that of bulk. The mechanical behavior of ZnO nanowires is well described by a mechanical model of bending and tensile stretching.     

Effect of sonochemical scouring on the surface morphologies,mechanical properties,and dyeing abilities of wool fibres

Ultrasonics has the potential to reduce the cost and environmental impact of textile processing. This work investigates the effects of ultrasonic irradiation during wool scouring on fibre surface morphologies, fibre mechanical properties, and fibre dyeing abilities. A range of ultrasonic frequencies were used in the scouring bath to examine the forms of fibre cuticle damage. It is observed that wool fibres underwent ultrasonic irradiation at a low frequency have severe modifications of the fibre surface structure. Despite some visible disruptions to the fibre scale structure however, ultrasonic irradiation has shown a negligible impact on the fibre mechanical properties, especially bending abrasion resistance which depends largely on the fibre surface conditions, and is responsible for the handle and pilling propensity of the resultant fabrics. Dyeing abilities were investigated on wool samples using commercially available acid dye and reactive dye. It is found that ultrasonically scoured wool has a quicker dye uptake in the early stage of low temperature dyeing for both acid dye and reactive dye, than the conventionally scoured wool.     

Study of the effect of varying core diameter,shell thickness and strain velocity on the tensile properties of single crystals of Cu–Ag core–shell nanowire using molecular dynamics simulations

Core–shell type nanostructures show exceptional properties due to their unique structure having a central solid core of one type and an outer thin shell of another type which draw immense attention among researchers. In this study, molecular dynamics simulations are carried out on single crystals of copper–silver core–shell nanowires having wire diameter ranging from 9 to 30 nm with varying core diameter, shell thickness, and strain velocity. The tensile properties like yield strength, ultimate tensile strength, and Young’s modulus are studied and correlated by varying one parameter at a time and keeping the other two parameters constant. The results obtained for a fixed wire size and different strain velocities were extrapolated to calculate the tensile properties like yield strength and Young’s modulus at standard strain rate of 1 mm/min. The results show ultra-high tensile properties of copper–silver core–shell nanowires, several times than that of bulk copper and silver. These copper–silver core–shell nanowires can be used as a reinforcing agent in bulk metal matrix for developing ultra-high strength nanocomposites.     

Variable photonic crystal fiber optical attenuator combining air hole reduction induced radiation and bending loss

Recently, an optical attenuator has been important in fiber optic communication systems, because a transmission power in fiber has become higher due to a channel increment in wavelength division multiplexing transmission. A photonic crystal fiber (PCF) optical attenuator is fabricated by air hole diameter reduction in a part of PCF in which radiations are caused in the air hole diameter reduced part of PCF. A PCF optical attenuator has a high power resistance feature due to its radiation-induced operation of optical attenuation. In this paper, we proposed a variable PCF optical attenuator in which a bend was applied to the air hole diameter reduced part in PCF optical attenuator that was fabricated by CO₂ laser irradiation. In PCF optical attenuator fabrication, the attenuation was adjusted by the reduced air hole diameter with laser irradiation time control. It was demonstrated that 10.6–13.5 dB of variable attenuation was obtained at 1550 nm-wavelength with 0°–90° bending angle applied to the air hole diameter reduced part in PCF optical attenuator.     

Studies on interfacial adhesion in unidirectional isora fibre reinforced polyester composites

Unidirectional isora fibre reinforced polyester composites were prepared by compression moulding. Isora is a natural bast fibre separated from the Helicteres isora plant by a retting process. The effect of alkali treatment on the thermal properties of the fibre was studied using TGA, DTA and DSC in oxygen and nitrogen atmosphere. Mechanical properties like tensile strength, Young's modulus, flexural strength, flexural modulus and impact strength of the composites containing untreated and alkali-treated fibres have been studied as a function of fibre loading. The optimum loading for tensile properties of the composite containing untreated fibre was found to be 45% by volume and on alkalization of the fibre, the optimum loading increased to 66%. For flexural properties the loading was optimized at about 56% and 66%, for the composites containing untreated and alkali treated fibres, respectively. From DMA studies it was observed that the alkali-treated fibre composites have higher E′ and E″ values compared to untreated fibre composites. From swelling studies in styrene it was observed that the mole percent uptake of the solvent by the treated fibre composites is less than by the untreated fibre composites. From these results it can be concluded that in composites containing alkalized fibres there is enhanced interfacial adhesion between the fibre and the matrix leading to better properties, compared to untreated fibre composites.     

Comparison of microstructure and mechanical properties of ultra-narrow gap laser and gas-metal-arc welded S960 high strength steel

The microstructural characteristics and mechanical properties, including micro-hardness, tensile properties, three-point bending properties and Charpy impact toughness at different test temperatures of 8 mm thick S960 high strength steel plates were investigated following their joining by multi-pass ultra-narrow gap laser welding (NGLW) and gas metal arc welding (GMAW) techniques. It was found that the microstructure in the fusion zone (FZ) for the ultra-NGLW joint was predominantly martensite mixed with some tempered martensite, while the FZ for the GMAW joint was mainly consisted of ferrite with some martensite. The strength of the ultra-NGLW specimens was comparable to that of the base material (BM), with all welded specimens failed in the BM in the tensile tests. The tensile strength of the GMAW specimens was reduced approximately by 100 MPa when compared with the base material by a broad and soft heat affected zone (HAZ) with failure located in the soft HAZ. Both the ultra-NGLW and GMAW specimens performed well in three-point bending tests. The GMAW joints exhibited better impact toughness than the ultra-NGLW joints.     

Influence of laser irradiation on the optical and structural properties of poly(ethylene terephthalate) fibres

Laser irradiation has been previously investigated for achieving uniform heating of polyethylene terephthalate (PET) fibres in the hot-drawing stage of the production process, so as to obtain better fibre mechanical properties. The optical properties and dye uptake of PET fibres also depend on the polymer chain orientation and crystallinity within the fibre structure. This paper reports an investigation of a concept whereby laser irradiation and interferometry could be used to modify and trace a small change in the optical properties of a PET monofilament fibre, but the corresponding change in the dye uptake would not be detected visually. A copper vapour laser (550-580 nm wavelengths) was used to expose consecutive 4 mm lengths along a running length of monofilament to 39.8 W cm⁻², at a pulse rate of 9.89 kHz in order to modify, in a controlled way, the polymer crystallinity and orientation. A 3D finite element simulation, based on uncoupled heat-transfer analysis, indicated that rapid heating and cooling could be obtained with the laser to give the small changes required. Irradiated and untreated samples were analysed by interferometry and a 0.16% change was detected in the birefringence profiles, corresponding to a small reduction in the degree of orientation and crystallinity of the irradiated samples. Density measurements and wide-angle X-ray scattering (WAXS) analysis confirmed the change in crystallinity. Tests conducted for dye adsorption and tensile strength showed a small increase in the former and only a very small decrease in the latter. It was concluded that these changes in property provide the opportunity for a laser-irradiated PET monofilament fibre to be used as a subtle tracer element in brand labels for textile garments as an anti-counterfeit measure.     

Measurement of mechanical deformation of dielectric fibres by a light scattering method

This paper describes an experimental method to detect quantitative changes of both refractive index and diameter of unclad dielectric fibres, such as fused silica fibre and nylon 6 fibre, due to tensile stress. The technique employed here is based on the variation in the position of a fringe in back-scattered light, which is generated when a laser beam is incident at a right angle to the axis of the fibre. This procedure makes it possible to measure refractive index, diameter and ellipticity to within an accuracy of 0.048%, 2.6% and 0.05%, respectively.     

Laser induced decohesion of coatings: probing by laser ultrasonics

The aim of the present study is to investigate a conventional laser-ultrasonics technique for the determination of intrinsic properties of oxide coatings and their adhesion strength on a metallic substrate. The good agreement between experiments and computations in an epicenter configuration allows determining the longitudinal wave velocity as well as the Young's modulus of the oxide coatings versus the porosity. For a critical value of the laser energy, a breakdown at the coating-substrate interface is generated by the laser irradiation. The critical tensile stress field developed at the coating/substrate interface, which leads to the interfacial fracture, can be easily calculated. The value of the practical adhesion which is defined is found to be in accordance with those obtained by classic contact techniques (tensile adhesion test, indentation, bending test). Finally, this work demonstrates that this quantitative, contactless test fits well to simultaneously characterise the oxide coatings and evaluate the coating-substrate adhesion.     

Welding of polymers using a 2 μm thulium fiber laser

Absorber-free transmission and butt-welding of different polymers were performed using thulium fiber laser radiation at the wavelength 2 μm. The relations between the laser process conditions and the dimensions and quality of the seam were investigated by means of optical and phase-contrast microscopy. Mechanical properties of the weld joints were studied in tensile strength tests. Laser-welded polyethylene samples revealed a tensile strength of greater than 80% of the bulk material strength. Transmission welding of different polymer combinations featured the formation of different joint classes depending on the spectral properties. The experiments demonstrate new application areas of mid-IR fiber laser sources for materials processing.     

Microstructural analysis of neutron-irradiation induced changes in polyester fibre studied using EPMA

Electron microscopy is an important characterization technique for the study of textile fibre as it gives more information on fabric wear, nature of fibre fracture, chemical degradation, abrasion, fatigue and many others. Electron Probe Micro Analyzer (EPMA) micrographs of virgin and some neutron-irradiated samples (graphite coated) are discussed. The filament diameter, D, of virgin PET fibre obtained from EPMA study was 12.5 μn. The surface topography of single filament distinctly reveals the core and sheath parts of the filament. The core diameter of the virgin fibre was estimated to be 1.43 μm. The fibre irradiated at fluence 1 × 10¹² n/cm² shows radiation induced sphere like polymer balls or spherulites of diameter 2.27 μm in the expanded core region. Due to irradiation, the sheath area crosslinks with expanded core region, which may be responsible for increase of strength and hardness of the polymer materials. Moreover, the micrograph at 3000 X magnifications clearly shows that there is no preferred orientation of the polymer in any direction confirming the isotropic nature of the sample.      

Experimental determination of the micro- and macrostructural parameters influencing the acoustical performance of fibrous media

Measurements of the two characteristic lengths of 6 glass wool samples (with flow resistivities between 11,900 and 69,900 Pa s m⁻²) and 6 polyester fibre samples (with flow resistivities between 4100 and 51,000 Pa s m⁻²) have been made. These data have been used to determine the cross-sectional shape factors which are related to the characteristic lengths introduced by Allard. By using the formulas due to Bies and Allard, it has been found that the two characteristic lengths of the glass wool samples can be independently predicted from the glass fibre diameter. In respect to polyester fibre samples, a new relation between the flow resistivity, the fibre diameter and the bulk density has been proposed and examined. The accuracy of the predictions of the non-acoustical parameters has been confirmed by the measurements and predictions of the absorption coefficient using the Delany and Bazley and Allard models.     

UV grafting of extended chain polyethylene fibres

A bench-scale continuous fibre treatment line has been built to modify polyethylene fibre surfaces using UV radiation-induced grafting. It is shown that grafting does indeed take place and that the grafts adhere well to the resin. Single-fibre pullout behaviour, interlaminar shear strength, and flexural behaviour were observed to improve considerably. The loss of tensile properties due to treatment was investigated and found to be small in the range of useful treatments. The interlaminar shear strength of the UV-treated fibre is as high as 38 MPa (5.5 ksi) as compared with the untreated fibre value of 10 MPa (1.5 ksi). The most important process parameters are identified and trends established.     

强激光辐照下纳米晶体铜薄膜层裂破坏的实验研究

采用强激光辐照加载技术和激光速度干涉(VISAR)测试技术，对纳米晶体铜薄膜的层裂特性进行实验测量和分析.基于VISAR实测的自由面速度波形，计算得到纳米晶体铜薄膜在超高拉伸应变率下的层裂强度高达3 GPa，明显高于多晶铜的层裂强度, 其原因归咎于纳米晶体材料中存在大量晶界阻碍了位错运动.     

强激光辐照下纳米晶体铜薄膜层裂破坏的实验研究

采用强激光辐照加载技术和激光速度干涉(VISAR)测试技术,对纳米晶体铜薄膜的层裂特性进行实验测量和分析.基于VISAR实测的自由面速度波形,计算得到纳米晶体铜薄膜在超高拉伸应变率下的层裂强度高达3 GPa,明显高于多晶铜的层裂强度, 其原因归咎于纳米晶体材料中存在大量晶界阻碍了位错运动. 关键词： 纳米晶体铜薄膜 层裂 激光辐照     

Laser irradiation effects on the surface,structural and mechanical properties of Al–Cu alloy 2024

Laser irradiation effects on surface, structural and mechanical properties of Al–Cu–Mg alloy (Al–Cu alloy 2024) have been investigated. The specimens were irradiated for various fluences ranging from 3.8 to 5.5 J/cm² using an Excimer (KrF) laser (248 nm, 18 ns, 30 Hz) under vacuum environment. The surface and structural modifications of the irradiated targets have been investigated by scanning electron microscope (SEM) and X-ray diffractometer (XRD), respectively. SEM analysis reveals the formation of micro-sized craters along the growth of periodic surface structures (ripples) at their peripheries. The size of the craters initially increases and then decreases by increasing the laser fluence. XRD analysis shows an anomalous trend in the peak intensity and crystallite size of the specimen irradiated for various fluences. A universal tensile testing machine and Vickers microhardness tester were employed in order to investigate the mechanical properties of the irradiated targets. The changes in yield strength, ultimate tensile strength and microhardness were found to be anomalous with increasing laser fluences. The changes in the surface and structural properties of Al–Cu alloy 2024 after laser irradiation have been associated with the changes in mechanical properties.     

Microstructuring of diamond bulk by IR femtosecond laser pulses

We report the fabrication of graphitic microstructures in the bulk of chemical vapor deposited (CVD) diamond using 120-fs laser pulses at 800-nm wavelength. The nature of the laser-modified region and generation of mechanical stresses in the surrounding diamond is studied with Raman spectroscopy. A spontaneous growth of the laser-modified region from the focal plane towards the laser has been visualized in the process of multipulse irradiation with different pulse energies. The formation of discrete or continuous graphitized structures is revealed depending on the varied local laser intensity. The physical processes governing the appearance of separate graphitic globules and continuous extension of the graphitized region are discussed. Controlling the laser irradiation conditions permits us to fabricate graphitic wires with typical length of 150 μm and diameter of 1.5 μm. The longer, 300-ps pulses, as applied to laser microstructuring of the CVD diamond bulk, are found to be inappropriate due to the stronger influence of structural defects on the damage threshold, the noticeable fluctuation of the structure diameter over the length and the pronounced cracking of the surrounding diamond. PACS 42.62.-b; 61.80.Ba