茶多酚中咖啡因的近红外光谱分析

采用近红外光谱分析技术对茶多酚中咖啡因进行了光谱及定量分析,原始光谱表明咖啡因在近红外波段有着很强且较为明显的吸收峰。通过对样品的漫反射原始吸光度光谱进行导数、散射校正及相关分析更清晰地给出了咖啡因在近红外光谱波段的光谱特性,为建立快速稳健的定标模型创造了条件。该技术能够解析出咖啡因中各主要基团在近红外波段的吸收特性,结合定标过程定量快速检测咖啡因在茶多酚中的含量,定标分析结果显示在很大的浓度范围内有很好的线性相关性,定标标准差SEC为0．49％,相关系数（r）为0．993,证实了近红外光谱分析技术作为一种新的快速分析茶多酚中咖啡因含量手段的可行性及优越性。     

重铬酸钾分光光度法测定沙棘茶中茶多酚的含量

重铬酸钾分光光度法测定了沙棘茶中的茶多酚总量。在硫酸强酸性介质中重铬酸钾氧化茶多酚,其吸光度随茶多酚浓度的增加而减小,且减小值与茶多酚的浓度呈线性关系。以儿茶素为对照品,校准曲线的回归方程为y=-0.034x+0.4746(r2=0.9986);对稳定性、精密度、回收率进行了试验。该方法简便、快速、准确,可用于沙棘茶中茶多酚总量的测定。     

波长色散X射线荧光光谱法测定黄金饰品含金量

本文提出应用波长色散Ｘ射线荧光光谱仪测定黄金饰品含金量的方法，本法对原有样品盒进行了改造，增设特制窗口和采取样品固定等措施，以系列参考标样建立校准曲线，用经验系数法校正基体效应。比例模拟法校正含量。９个参考标样和１６个金标牌的测定结果表明，在含金量为３７．５０％－９９．９９％的范围内，方法的准确度好：含金量在９９．９９％－９８．９８％范围时，误差为０．０３％－０．１２％，在９８．９８％－３７．５０％范围时，误差为０．０１％－０．５２％，选用含金量不同的５个参考标样为代表，以０．７和１．４的模拟比例，经不同时间多次测定进行统计，相对标准偏差为０．０５％－０．５０％，说明方法的精密度好，本法操作方便，时样品无破坏     

火焰原子吸收光谱法测定铜镍矿浮选产品中铜、镍、镁

研究了用火焰原子吸收光谱法在同一溶液体系中直接快速测定金川铜镍矿浮选产品中铜、镍、镁含量新的新方法。考察了产品中高含量的SiO2对测定镁的干扰情况，并提出了排除这项干扰简便方法，根据各元素的标准溶液系列的测定数据，推算出了铜、镍、镁3元素的线性回归方程及线性相关系数，特征浓度铜为0．40mg.L^-1/1%，镍为0．48mg.L^-1／1％，Mg为0．018mg.L^-1／1％；线性浓度范围铜，镍均为0－10mg.L^-1，镁为0．2－1．2mg.L^-1。相对标准偏差铜为2．5％(n=6)，镍为2．3％（n＝6），镁为2．8％（n=6），加标回收率铜为96．5％－102．5％，镍为98．8％－103．5％，镁为98．2％－102．5％，这种方法操作简便，快速，实用，具有较好的精密度和准确度，实际产品分析结果与外检单位及金川公司测定的结果吻合。     

ICP-AES法测定水中微量磷

用ICP－AES法测定水中磷，并确定了最佳测定条件，检出限为0．02μg.mL^-1，回收率为96．5％－102．1％，RSD为1．65％－2．83％。该法准确、快速、简便，应用于水中磷的测定，结果令人满意。     

石墨炉原子吸收光谱法测定抗菌纤维中的银

石墨炉原子吸收光谱法测定抗菌纤维中的银，回收率为90．9％-95．9％，相对标准偏差为2．4％-3．3％。方法简便、快速、准确，具有较好的精确度和准确度。     

火焰原子吸收法同时测定地质样品中金和银

二氯化锡还原，二氯化汞共沉淀，火焰原子吸收法同时测定地质样品中金和银。对于原矿和尾矿样品，金含量为５．１５μｇ／ｇ，４．４５μｇ／ｇ和０．５４μｇ／ｇ时，相对标准偏差分别为６．２％，３．４％和４．１％。银含量为９．７８μｇ／ｇ和１．２２μｇ／ｇ时，相对标准偏差分别为４．４％，３．５％和１２．５％。金的分析结果与参考值基本一致。金和银的回收率分别为８８－１０２％和８５－１００％。方法具有干扰小，分离     

聚酰胺树脂对茶多酚和咖啡因吸附选择性研究

本文用紫外可见分光光度法研究了聚酰胺树脂对茶多酚和咖啡因的吸附性能 ,分光光度法和HPLC研究表明 ,聚酰胺树脂对茶多酚的吸附能力远大于对咖啡因的吸附能力 ,氢键起了非常重要的作用。在2 0g聚酰胺树脂对 1 0 0mL 0 71g·L- 1 咖啡因水溶液的静态吸附实验中 ,其吸附量为 2 65mg·g- 1 ,吸附率为7 5 % ;8 0g聚酰胺树脂对 70 0mL 1 98g·L- 1 茶多酚水溶液的静态吸附实验 ,吸附量高达 1 4 8 1 3mg·g- 1 ,吸附率为 85 5 % ;以 85 %的乙醇为洗脱剂 ,咖啡因和茶多酚的解吸率分别为 74%和 90 % ;同时聚酰胺树脂对咖啡因和茶多酚的静态吸附在 80min内达到快速吸附平衡 ,并且吸附动力学曲线接近线性。利用树脂成功地将茶多酚和咖啡因混合溶液进行了吸附分离 ,得到的产品茶多酚含量高于 96 % ,其中EGCG含量高于80 % ,而咖啡因含量则小于 2 82 %。实验结果表明 ,聚酰胺树脂适合吸附分离咖啡因和茶多酚。     

石墨炉原子吸收法测定化妆品中的铅和砷

本文研究了石墨炉原子吸收法测定化妆品中铅、砷的方法。用湿式消解法消化样品，易掌握。方法简便，灵敏度高。用本方法测定铅的检出限为０．０１０ｎｇ，砷的检出限为０．０１３ｎｇ，相对标准偏差为０．８％－５．２％，方法的回收率为９６．１％－１０５．８％。     

ICP—AES法测定钒酸钇钕晶体中Nd,V和Y

本文用硫酸溶解样品，无需加内标元素，可以同时测定钒酸钇钕酸晶体中Ｎｄ，Ｖ和Ｙ含量，并取得满意结果，主含量Ｖ，Ｙ回收率为９９．５％－１００．６％，Ｎｄ回收率为９８．７％－１０２．４％相对标准偏差均小于１％。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.