On-line preconcentration and determination of Zn in natural water samples employing a styrene-divinylbenzene functionalized resin and flame atomic absorption spectrometry.

In this work, flame atomic absorption spectrometry (FAAS) was used as a detector for the determination of zinc in natural water samples with a flow-injection system coupled to solid-phase extraction (SPE). In order to promote the on-line preconcentration of zinc from samples a minicolumn packed with 35 mg of a styrene-divinylbenzene resin functionalized with (S)-2-[hydroxy-bis(4-vinylphenyl)methyl]pyrrolidine-1-carboxylic acid ethyl esther was utilized. The system operation was based on Zn(II) ion retention at pH 9.5 +/- 0.5 in such a minicolumn with analyte elution, at the back flush mode, with 1 mol L(-1) HCl directly to the FAAS nebulizer. The influence of the chemical (sample pH, buffer concentration, HCl eluent concentration and effect of the ionic strength) and flow (sample and eluent flow rates and preconcentration time) parameters that could affect the performance of the system were investigated as well as the possible interferents. At the optimum conditions, for 2 min of preconcentration time (9.9 ml of sample volume), the developed methodology presented a detection limit of 1.1 microg L(-1), a RSD of 3.5% at 10 microg L(-1) and an analytical throughput of 24 h(-1). Whereas, for 4 min of the preconcentration time (19.8 ml of sample volume) a detection limit of 0.98 microg L(-1), a RSD of 6.5% at 5 microg L(-1) and a sampling frequency of 13 h(-1) are reported.     

Flow injection/atomic absorption spectrometric determination of zineb in commercial formulations of pesticide based on slurry sampling.

This paper reports on a new strategy for the slurry sampling determination of dithiocarbamate pesticide zineb [[ethylenebis(dithiocarbamato)]zinc] employing a FIA system with a flame atomic absorption spectrometry detector. In the flow system, an on-line alkaline hydrolysis of the pesticide is performed, allowing the release of Zn(II) ions to the solution, which are easily detected by a flame AAS technique. Several parameters that could affect the performance of the analytical methodology were studied, such as the concentration of NH3(aq) used in the hydrolysis step, the effect of the presence of Triton X-100 on the sensitivity and precision, and the FIA parameters (carrier flow rate and mixing coil volume). Under optimized conditions, aqueous slurries containing 2.5 to 25 microg ml(-1) zineb provided good linear calibration fits. From the obtained data, a detection limit (3sigma) of 1.0 microg ml(-1) zineb was found and a repeatability of 2.7% was obtained from 12 measurements of a slurry containing 2.5 microg m(-1) zineb. On the other hand, a precision (reproducibility) of 7.8% was achieved from three determinations of a sample containing 128 mg g(-1) of the pesticide. Also, the developed system provides a sampling frequency of 72 h(-1).     

Improvements in cobalt determination by thermospray flame furnace atomic absorption spectrometry using an on-line derivatization strategy

An on-line derivatization strategy was developed for improving cobalt sensitivity using thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) as the analytical technique. This strategy involves the generation of a volatile cobalt compound, providing better sample vaporization efficiency. The effect of sodium diethyldithiocarbamate (DDTC) as complexing agent on the integrated absorbance signal was evaluated. Parameters including the pH of complex formation, complex concentration and volume, sample volume, flame gas composition and tube atomization configuration were optimized. A wide linear range (from 23 microg L(-1) to 3 mg L(-1); r(2)=0.9786) was obtained, with the best one (r(2)=0.9992) attained from 23 to 400 microg L(-1) with a sample throughput of 30 h(-1). The improvement in the detection power was 17-fold when compared to FAAS, which provides 7 microg L(-1) as the limit of detection when considered TS-FF-AAS technique. A relative standard deviation (n=10) of 4% for a cobalt solution containing 50 microg L(-1) was attained, and the accuracy of the procedure was evaluated through certified reference materials (IAEA-SL-1, lake sediment; and ISS-MURST-A1, Antarctic marine sediment). Good agreement between the results at the 95% confidence level was observed.     

Minicolumn field sampling--preconcentration of trace zinc from seawater and its laboratory detection by flow injection flame atomic absorption spectrometry.

A simple field sampling-preconcentration method for zinc determination in seawater is described. Seawater was collected in situ by pumping it through a minicolumn packed with a chelating resin (Chelite P) connected to a field flow preconcentration system (FFPS). These packed minicolumns retain the dissolved zinc, and once are loaded with the analyte, they are returned to the laboratory where they are sequentially inserted into a flow injection system for on-line zinc elution with diluted hydrochloric acid and flame atomic absorption spectrometric detection. A factorial design has been used to optimize the FFPS and the flow injection elution process. The proposed method has a linear calibration range from 0.07 to at least 9.4 microg L(-1) of zinc, with a detection limit of 0.02 microg L(-1) and a throughput of 26 samples h(-1). Validation was carried out against certified reference water samples. This procedure has been successfully applied to the determination of Zn in seawater samples from Galicia (Spain).     

Resonance light scattering method for the determination of anionic surfactant with acridine orange

The resonance Rayleigh scattering (RRS), second-order scattering (SOS) and frequency-double scattering (FDS) spectra of sodium dodecylbenzene sulfonate (SDBS) (anionic surfactant (AS)) with acridine orange (AO) system were studied. Experimental results showed that when lambda(em) = lambda(ex) = 537 nm, the RRS peak of AO was greatly enhanced with the increase of SDBS concentration at a pH range of 1.8-4.0. The linear range of the calibration curve for SDBS was 0.028-8.71 mg L(-1) with a detection limit of 8.36 microg L(-1) when the AO concentration was 2.5 x 10(-5)mol L(-1). The method has been applied to the determination of trace amount of AS in environmental water samples with satisfactory results. In addition, when lambda(em) = 321 nm and lambda(ex) = 642 nm, the intensity of FDS was proportional to the SDBS concentration ranging from 0.014 to 8.71 mg L(-1) and the correlation coefficient was 0.993 with a detection limit of 4.31 microg L(-1); when lambda(em) = 642 nm and lambda(ex) = 321 nm, the intensity of SOS was proportional to the SDBS concentration ranging from 0.050 to 8.71 mg L(-1), and the correlation coefficient was 0.993 with a detection limit of 14.9 microg L(-1).     

Determination of cadmium by flow injection-chemical vapor generation-atomic absorption spectrometry

A method was developed for the generation of a "cold vapor" of cadmium by means of flow injection-chemical vapor generation from aqueous samples, the determination being conducted with an atomic absorption spectrometer (Pyrex glass T-cell). Several gas-liquid separator designs, atomizer designs, and the effect of several reagents previously reported as sensitivity enhancers (including cobalt, nickel, thiourea and didodecyl-dimethylammonium bromide) were investigated. The limit of detection, calculated as the concentration giving a signal equal to three times the standard deviation of the blank, was 16 ng L(-1), and the relative standard deviation was 1.4% for a concentration of 2 microg L(-1) and 3.8% for 0.1 microg L(-1). The addition of nickel and thiourea to the samples provided improved tolerance to the interference of coexisting ions. Two NIST certified reference materials, Montana Soil and Apple Leaves (respectively containing 41.7+/-0.25 mg kg(-1) Cd and 0.013+/-0.002 mg kg(-1) Cd) were accurately analyzed. The interference of lead was overcome by coprecipitation with barium sulfate, and the experimental values obtained were 41+/-1 mg kg(-1) Cd and 0.013+/-0.002 mg kg(-1) Cd, respectively.     

Electrothermal atomic absorption spectrometric determination of cobalt in biological samples and natural waters using a flow injection system with on-line preconcentration by ion-pair adsorption in a knotted reactor

An on-line flow injection preconcentration-ETAAS method is developed for trace determination of cobalt in biological materials and natural samples by ion-pair sorption on the inner walls of a PTFE knotted reactor. The ion-pair is formed between the negatively charged cobalt-nitroso-R-salt complex and the tetrabutylammonium counter-ion. An enhancement factor of 15, a sampling frequency of 17 and a concentration efficiency of 4 are obtained for a preconcentration time of 60 s and a sample loading flow rate of 5 mL min(-1). The detection limit (3sigma) is 5 ng L(-1). The relative standard deviation at the 0.2 microg L(-1) level is 2.3%. The analytical results obtained for standard reference materials are in good agreement with the certified or indicated values and satisfactory recoveries of spiked cobalt in tap water are obtained.     

Simultaneous on-line pre-concentration and determination of trace metals in environmental samples by flow injection combined with inductively coupled plasma mass spectrometry using silica gel modified with niobium(V) oxide

This work presents the development of an on-line pre-concentration system for simultaneous determination of Cd, Cu, Ni, V, Zn, Co and Pb in aqueous environmental samples and detection by inductively coupled plasma mass spectrometry. The system is based on cationic retention of the analytes onto a mini-column filled with silica gel modified with niobium(V) oxide. The effects of chemicals and flow variables have been investigated. The optimized operating conditions, selected as a compromise between sensitivity and analytical frequency were: sample pH 7.0, sample flow rate of 6.0mL min(-1), eluent flow rate of 2.0mL min(-1), and eluent (HNO(3)) concentration of 2.5mol L(-1). The relative standard deviation (n=7), enrichment factor and linear working range were 0.8-4.5%, 23.3-37.2 and 0.05-25.0microg L(-1), respectively. Limits of detection were between 0.01 and 0.03microg L(-1). The accuracy of the proposed method was checked with certified materials (NASS-4, NASS-5, CASS-4 and SRM 1643e). Values obtained were in accordance with those reported for the certified materials. Recovery was found to be in the range of 90-110% for a suit of water samples with variable matrices (seawater, tap water and ground water) collected in Florianopolis, Brazil.     

Solid-phase extraction and spectrophotometric determination of mercury with 6-mercaptopurine in environmental samples

A highly selective, sensitive and rapid method for the determination of trace amounts of inorganic mercury based on the reaction of Hg (II) with 6-mercaptopurine and the solid phase extraction of the complex on C18 membrane disks was developed. The 6-mercaptopurine selectively reacts with Hg (II) to form a complex in the pH range of 5-8. This complex was preconcentrated by solid phase extraction with C18 disks. An enrichment factor of 100 was achieved. The molar absorptivity of the complex is 0.26 x 10(-6) L. mol(-1) cm(-1) measured at 315 nm. The Beer's law is obeyed in the concentration range of 0.002-0.048 microg mL(-1). The relative standard deviation for eleven-replicated measurement of 0.04 microg mL(-1) is 1.5 %. The detection limit is 0.001 microg mL(-1) in the water samples. The advantage of the method is that the determination of Hg (II) is free from interference of almost all the cations and anions found in environment and wastewater samples. The determination of Hg (II) in water samples of different origins and marine sediment were carried out by the present method and cold vapor atomic absorption spectrometry (CVAAS). Also the method's accuracy was investigated by using SRM 2709. The obtained results by the present procedure were in good agreement with those of the CVAAS and certified value, so that the applicability of the proposed method was confirmed for the real samples.     

Detection of dopamine in the pharmacy with a carbon nanotube paste electrode using voltammetry

A simply prepared DNA immobilized on a carbon nanotube paste electrode (CNTPE) was utilized to monitor dopamine ion concentration using the cyclic voltammetry (CV) and square-wave (SW) stripping voltammetry methods. The optimum analytical conditions were sought. The result obtained was a very low detection limit compared to other common voltammetry methods. The optimal parameters were found to be as follows: 3.5 pH, 0.48 V SW amplitude, 71 Hz frequency, 5 s accumulation time, 0.01 V increment potential, and -1.3 V (anodic-*-) and 1.2 V (cathodic-o-) accumulation potentials. Given these conditions, the linear working range was observed to be within 0.01-0.11 microg L(-1) (SW anodic and CV). The analytical detection limit was determined to be SW anodic and CV: 4.0 microg L(-1) (2.1 x 10(-11) mol L(-1)) dopamin, and the relative standard deviation at the dopamine concentration of SW anodic 0.05 microg L(-1) was 0.02% (n=15) at the optimum conditions.     

Univariate and simplex optimization for the flow-injection spectrophotometric determination of copper using nitroso-R salt as a complexing agent.

A simple colorimetric flow-injection system for the determination of Cu(II) based on a complexation reaction with nitroso-R salt is described. The chemical and FIA variables were established using the univariate and simplex methods. A small volume of Cu(II) was mixed with merged streams of nitroso-R salt and acetate buffer solutions. The absorbance of the complex was continuously monitored at 492 nm. The calibration curve over the concentration range 1.0-7.0 microg ml(-1) was obtained. The relative standard deviation for determining 4.0 microg ml(-1) Cu(II) was 0.47% (n = 11). The detection limit (3sigma) was 0.68 microg ml(-1) and the sample throughput was 150 h(-1). The validity of the method has been satisfactorily examined for the determination of Cu(II) in wastewater and copper ore samples. The accuracy was found to be high, because the student t-values were calculated to be less than the theoretical values when the results were compared with those obtained by FAAS.     

Determination of the herbicide benfuresate by its photo-induced chemiluminescence using flow multicommutation methodology

The present paper deals with an analytical strategy based on coupling photo-induced chemiluminescence in a multicommutation continuous-flow methodology for the determination of the herbicide benfuresate. The solenoid valve inserted as small segments of the analyte solution was sequentially alternated with segments of the NaOH solution for adjusting the medium for the photodegradation. Both flow rates (sample and medium) were adjusted to required time for photodegradation, 90 s; and then, the resulting solution was also sequentially inserted as segments alternated with segments of the oxidizing solution system, hexacyanoferrate (III) in alkaline medium. The calibration range from 1 microg L(-1) to 95 mg L(-1), resulted in a linear behaviour over the range 1 microg L(-1) to 4 mg L(-1) and fitting the linear equation: I=4555.7x+284.2, correlation coefficient 0.9999. The limit of detection was 0.1 microg L(-1) (n=5, criteria 3 sigma) and the sample throughput was 22 h(-1). The consumption of solutions was very small; per peak were 0.66 mL, 0.16 mL and 0. 32 mL sample, medium and oxidant, respectively. Inter- and intra-day reproducibility resulted in a R.S.D. of 3.9% and 3.4%, respectively. After testing the influence of a large series of potential interferents the method is applied to water samples obtained from different places, human urine and to one formulation.     

Hydride generation for the direct determination of trace and ultra-trace level of arsenic and antimony in waters using derivative atomic absorption spectrometry

A new method is developed for the direct determination of trace and ultra-trace level of arsenic and antimony in waters by hydride generation derivative atomic absorption spectrometry (DHGAAS). The signal model and fundamentals of DHGAAS are described. The effects of atomization temperature, argon flow rate, acidity and concentration of KBH(4)and KI were investigated and analytical conditions were optimized. The sensitivities for arsenic and antimony were increased 36.4 and 27.6 times better than those of conventional hydride generation atomic absorption spectrometry (HGAAS). For a 2 mV min(-1) sensitivity range setting, the characteristic concentration was 0.003 microg L(-1) for arsenic and 0.004 microg L(-1)for antimony, and the detection limits (3sigma) were 0.015 micro g L(-1) for arsenic and 0.020 microg L(-1) for antimony. The proposed method was applied to the determination of arsenic and antimony in several water samples with satisfactory results.     

Determination of acetaldehyde in fuel ethanol by high-performance liquid chromatography with electrochemical detection.

The cyclic voltammetric behavior of acetaldehyde and the derivatized product with 2,4-dinitrophenylhydrazine (DNPHi) has been studied at a glassy carbon electrode. This study was used to optimize the best experimental conditions for its determination by high-performance liquid chromatographic (HPLC) separation coupled with electrochemical detection. The acetaldehyde-2,4-dinitrophenylhydrazone (ADNPH) was eluted and separated by a reversed-phase column, C18, under isocratic conditions with the mobile phase containing a binary mixture of methanol/LiCl(aq) at a concentration of 1.0 x 10(-3) M (80:20 v/v) and a flow rate of 1.0 mL min(-1). The optimum condition for the electrochemical detection of ADNPH was +1.0 V vs. Ag/AgCl as a reference electrode. The proposed method was simple, rapid (analysis time 7 min) and sensitive (detection limit 3.80 microg L(-1)) at a signal-to-noise ratio of 3:1. It was also highly selective and reproducible [standard deviation 8.2% +/- 0.36 (n = 5)]. The analytical curve of ADNPH was linear over the range of 3-300 mg L(-1) per injection (20 microL), and the analytical recovery was > 99%.     

On-line complexation of zinc with 5-Br-PADAP and preconcentration using a knotted reactor for inductively coupled plasma atomic emission spectrometric determination in river water samples

An on-line zinc preconcentration and determination system implemented with inductively coupled plasma atomic emission spectrometry (ICP-AES) associated with flow injection (FI) was studied. The zinc was retained as zinc-2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Zn-(5-Br-PADAP)) complex at pH 9.2. The zinc complex was removed from the knotted reactor (KR) with 30% v/v nitric acid. An enrichment factor of 42 was obtained for the KR system with respect to ICP-AES using pneumatic nebulization. The detection limit for the preconcentration of 10 mL of aqueous solution was 0.09 microg/L. The precision for 10 replicate determinations at the 5 microg/L Zn level was 2.3% relative standard deviation (RSD), calculated with the peak heights obtained. The calibration graph using the preconcentration system for zinc was linear with a correlation coefficient of 0.9997 at levels near the detection limits up to at least 100 microg/L. The method was succesfully applied to the determination of zinc in river water samples.     

Atomic absorption spectrometry for the automatic indirect determination of ascorbic acid based on-the reduction of manganese dioxide.

A new and simple flow injection method followed by atomic absorption spectrometry has been developed for the indirect determination of ascorbic acid. The proposed method is based on oxidation of ascorbic acid to dehydroascorbic acid using a solid-phase manganese dioxide (30% m/m suspended on silica gel beads) reactor. The flow of the sample through the column reduces the MnO2 to Mn(II) in an acidic carrier stream of 6.3 mM HNO3 (pH 2.2) with flow rate of 4.0 ml/min at room temperature; Mn(II) is measured by atomic absorption spectrometry. The absorbance of Mn(II) is proportional to the concentration of ascorbic acid in the sample. The calibration curve was linear up to 30 mg/L, with a detection limit of 0.2 mg/L for a 220 microL injected sample volume. The developed procedure was found to be suitable for the determination of AsA in pharmaceuticals and foods with a relative standard deviation better than 1.09% and a sampling rate of about 95 h(-1). The results exhibit no interference from the presence of large amounts of organic compounds. The reliability of the method was established by parallel determination against the 2,6-dichlorophenol-indophenol methods.     

A fluorescent probe for zinc ions based on N-methyltetraphenylporphine with high selectivity

N-methyl-alpha,beta,gamma,delta-tetraphenylporphine (NMTPPH) has been used to detect trace amount of zinc ions in ethanol-water solution by fluorescence spectroscopy. The fluorescent probe undergoes a fluorescent emission intensity enhancement upon binding to zinc ions in EtOH/H(2)O (1:1, v/v) solution. The fluorescence enhancement of NMTPPH is attributed to the 1:1 complex formation between NMTPPH and Zn(II) which has been utilized as the basis for the selective detection of Zn(II). The linear response range covers a concentration range of Zn(II) from 5.0x10(-7) to 1.0x10(-5)mol/L and the detection limit is 1.5x10(-7)mol/L. The fluorescent probe exhibits high selectivity over other common metal ions except for Cu(II).     

Large-volume sample stacking for analysis of ethylenediaminetetraacetic acid by capillary electrophoresis

A simple, quick, and sensitive capillary electrophoretic technique-large volume stacking using the electroosmotic flow (EOF) pump (LVSEP) - has been developed for determining ethylenediaminetetraacetic acid (EDTA) in drinking water for the first time. It is based on a precapillary complexation of EDTA with Fe(III) ions, followed by large-volume sample stacking and direct UV detection at 258 nm. The curve of peak response versus concentration was linear from 5.0 to 600.0 microg/L, and 0.7 to 30.0 mg/L. The regression coefficients were 0.9988 and 0.9990, respectively. The detection limit of the current technique for EDTA analysis was 0.2 microg/L with an additional 10-fold preconcentration procedure, based on the signal-to-noise ratio of 3. As opposed to the classical capillary zone electrophoresis (CE) method, the detection limit was improved about 1000-fold by using this LVSEP method. To the best of our knowledge, it represents the highest sensitivity for EDTA analysis via CE. Several drinking water samples were tested by this novel method with satisfactory results.     

Colorimetric determination of copper in aqueous samples using a flow injection system with a pre-concentration poly(ethylenimine) column

A colorimetric flow injection-system for the determination of Cu(II) in waters based on complexation reaction with 4-(2-pyridylazo)-resorcinol, usually termed PAR, is described. Performing measurements in 0.25 mol l(-1) HNO(3) medium allowed improved selectivity of the analytical method. The lack of sensitivity deriving from the low complex absorption under acidic conditions was balanced by the insertion of an immobilised poly(ethylenimine) (PEI) column where Cu(II) pre-concentration in neutral media occurs. Using sample volumes ranging from 2 to 4 ml, sampling rates of 24 and 12 samples h(-1) within a detection limit of 25 and 13 mug l(-1), respectively, were accomplished. Accuracy of the developed methodology was assessed by comparison with atomic absorption spectrometry being the relationship [FIA] mg l(-1)=1.00 (+/-0.03)x[AAS] mg l(-1)+0.00 (+/-0.02) obtained after analysing 15 samples. Precision was also evaluated using two samples of 0.05 and 0.5 mg l(-1) copper, and a relative standard deviation (R.S.D.) better than 3% was attained for both.     

Flow injection photoinduced chemiluminescence determination of imazalil in water samples

In this work, a fast, simple and economic method is proposed for the determination of imazalil in water samples by flow injection photoinduced chemiluminescence. In this method, imazalil degrades in basic media through the use of a photoreactor, and the resulting photofragments react with ferricyanide and generate the direct chemiluminescence signal. To the authors' knowledge, this is the first time that a chemiluminescence method has been proposed for the determination of this fungicide. All physical and chemical parameters in the flow injection chemiluminescence system were optimized in the experimental setting. In the absence of preconcentration, the linear dynamic range for imazalil was 0.75-5 mg L(-1) and the detection limit was 0.171 mg L(-1). The application of solid-phase extraction with C18 cartridges allowed the elimination of interference ions, the reduction of the linear dynamic range to 15-100 μg L(-1), and a detection limit of 3.4 μg L(-1). This detection limit is below the maximum concentration level established by the Regulations of the Hydraulic Public Domain for pesticide dumping. The sample throughput after solid-phase extraction of the analyte was 12 samples h(-1). The intraday and interday coefficients of variation were below 9.9% in all cases. This method was applied to the analysis of environmental water samples, and recoveries of between 95.7 and 110% were obtained.