核壳型含氟丙烯酸酯共聚物的合成及性能

采用饥饿态半连续种子乳液聚合方法, 在十二烷基硫酸钠(SDS)/辛基苯基聚氧乙烯醚(TX-10)复合乳化剂的作用下, 分别选用甲基丙烯酸三氟乙酯(TFEM)、甲基丙烯酸六氟正丁酯(HFBM)和甲基丙烯酸十二氟庚酯(DFHM)为含氟单体, 合成以丙烯酸正丁酯(BA)、甲基丙烯酸甲酯(MMA)和含氟单体为原料的核壳型结构含氟丙烯酸酯共聚物乳液. FTIR, 1H NMR, TEM和DSC分析结果显示, 获得了BA/MMA/含氟单体的共聚物乳液, 且乳液具有明显的核壳结构. DSC, TGA和SEM-EDX的分析显示, 核壳型结构的共聚物具有优异的热力学稳定性能和成膜性能; 长侧链或短侧链含氟单体对共聚物的热稳定性影响不明显, 但侧链较长的含氟单体所获得的聚合物在成膜过程中更易向表面迁移, 更能体现含氟聚合物的优点.     

含氟丙烯酸酯-苯乙烯共聚物的制备及其表面性能的研究

研究了聚合工艺、含氟丙烯酸酯类单体种类和用量、苯乙烯和自由基引发剂用量及硅烷偶联剂、催化剂等因素对含氟丙烯酸酯-乙烯共聚物表面性能的影响。结果表明：聚合工艺、含氟丙烯酸酯类单体种类和用量对共聚物表面的憎水性能有显著的影响;采用延时滴加含氟丙烯酸酯类单体可提高共聚物膜表面的憎水性;随含氟丙烯酸酯类单体侧链含氟烷基的链长和氟原子数及含氟单体用量的增加,共聚物水接触角增大,吸水率下降;共聚物薄膜的硬度则与含氟丙烯酸酯类单体中α-取代基、侧链含氟烷基的链长和用量、苯乙烯用量、引发剂浓度等相关;硅烷偶联剂和催化交联剂的加入可提高共聚物薄膜的强度。     

优化含氟丙烯酸酯共聚物乳胶膜表面性能的方法研究

含氟丙烯酸酯乳液由于氟的引入具有优异的表面性能,在涂料、胶粘剂、纺织助剂等领域得到广泛应用.然而含氟单体成本较高,而且产物中乳化剂的存在影响了含氟丙烯酸酯乳液涂膜的抗污、疏水疏油等特性.如何采取有效措施提高含氟丙烯酸酯共聚物乳胶膜的表面性能,是其走向产业化急需解决的问题.针对这方面问题,本文主要从含氟单体的利用率、设计乳胶粒结构、共聚物链结构以及乳胶膜的后处理等方面对近年来的研究成果进行了综述.     

低表面能侧基含氟聚合物*

含氟聚合物材料具有优异的热稳定性、极低的表面能、强化学稳定性和生物相容性等,在功能涂料、织物整理、微电子、汽车以及航空航天等领域具有很好的应用前景。本文综述了侧基含氟聚合物的主链、全氟烷基链、主链与全氟烷基链段间连接基团的结构对聚合物表面性能的影响,并总结了环境友好型低表面能侧基含氟聚合物的研究进展。     

亲水单体对聚氨酯-含氟丙烯酸酯复合乳液颗粒和表面性能的影响

为了提高聚氨酯-丙烯酸酯聚合物的耐水性和耐溶剂性, 将N-甲基二乙醇胺(MDEA)扩链的交联聚氨酯丙酮溶液作为反应介质, 以苯乙烯、丙烯酸丁酯、含氟丙烯酸酯(FA)为单体, 过氧化苯甲酰为引发剂, 通过溶液聚合相转化法制得新型阳离子聚氨酯-含氟丙烯酸酯复合乳液. 研究了MDEA对聚合物水分散液的乳胶粒径、Zeta电位以及乳胶膜表面性能的影响, 并用FTIR, TEM对聚合物的结构和乳胶粒形态进行了表征. 结果表明, MDEA的添加利于降低乳胶粒径, 但对乳胶膜的疏水性能有不利影响, 当MDEA的质量分数为13.15%时, FPUA乳胶粒的形态呈球形, 粒径约为253 nm, 乳胶膜的表面自由能低于25.1 mJ/m², 接触角衰减速率约为0.38 (º)/min. 另外, 乳胶膜的高温处理能够使表面自由能降低11.5%以上.     

接枝改性PVDF基含氟聚合物

聚偏氟乙烯(PVDF基)含氟聚合物由于其独特的性能受到了广泛的关注.将功能化链段引入PVDF基含氟聚合物可以进一步提升其性能并拓展其应用领域.相较于物理共混法和直接共聚改性法,通过接枝改性法将功能化单体引入含氟聚合物的侧链具有更显著的优势,可便捷、高效地得到组成精确,结构可控的接枝共聚物.本文综述了通过活性自由基聚合(...     

阳离子无皂含氟丙烯酸酯的合成与表面性能

在合成甲基丙烯酸全氟辛酰氧基乙酯(FA)基础上,用半连续法制备了无皂阳离子含氟丙烯酸酯乳液。当乳液的粒径在100~200 nm、ζ电位大于40 mV时,乳液较稳定。阳离子亲水单体甲基丙烯酰氧乙基三甲基氯化铵(DMC)在含氟丙烯酸酯中质量分数为0.10~0.18、固含量小于20%时乳液的稳定性好,且随DMC含量的增加稳定性提高;含氟丙烯酸酯乳胶膜的附着力与耐磨性好,乳胶膜的透湿率随DMC的增加而增加。随热处理温度的提高,膜表面自由能下降;经160℃热处理后膜发生了交联,表面自由能为18 mN/m,与聚四氟乙烯(PTFE)的表面能相近,DMC含量对膜表面自由能影响不大。XPS分析也表明膜表面氟含量随热处理温度的提高而增加。     

自交联型含氟丙烯酸酯共聚物的合成与表征

含氟丙烯酸酯;自交联;无皂乳液;接触角滞后     

含氟丙烯酸酯聚合物乳胶膜表面性质

采用XPS和界面张力仪分别测定了含氟丙烯酸酯聚合物乳胶膜表面的组成及水在其表面的动态接触角, 并用状态逼近方程模型计算了含氟聚合物乳胶膜的表面张力, 考察了温度对乳胶膜润湿性的影响. 结果表明, 含氟聚合物乳胶膜表层较深处的F 1s信号强度比近表面要弱, 乳胶膜表面张力随表面氟原子浓度增加在一定程度上呈现线性下降；含氟侧链(Rf)较长(碳原子数n＞6)的含氟聚合物, 其表面张力随Rf单元含量增加而下降的趋势显著高于Rf较短(n≤6)的含氟聚合物, 而水在含氟聚合物乳胶膜表面上的后退接触角θr随n增大出现急剧上升, n≥10 时, θr值几乎恒定不再随n增大而改变. 此外, 参与共聚的非氟丙烯酸酯酯基碳链较短时, 水在共聚物乳胶膜表面的θr随氟单元含量增加而增加的趋势更显著；温度超过40 ℃后, 水对聚合物乳胶膜的润湿性随温度上升略有改善.     

含氟丙烯酸酯共聚物表面性能的稳定化研究

为提高传统含氟丙烯酸酯乳胶膜表面性能的稳定性,以γ-(甲基丙烯酰氧基)丙基三甲氧基硅烷(MPS)作为可交联单体,采用细乳液聚合法合成了MPS改性的含氟丙烯酸酯共聚物,利用DLS、TEM、IR对聚合物进行表征,研究了MPS对合成乳液的稳定性、涂膜性能和膜表面接触角稳定性的影响。结果表明,细乳液聚合法适合用于对水敏感单体的聚合,合成的纯丙烯酸酯乳胶为球形结构,平均粒径为92 nm,而氟丙乳胶和含3%MPS的含硅氟丙乳胶形成了典型的核壳结构,平均粒径分别增大至107 nm和103 nm,含硅氟丙聚合物中存在Si-O-Si的交联结构。涂膜性能测试表明,MPS的引入增加了共聚物膜的硬度、耐溶剂性和耐水性。接触角测试表明,随MPS用量的增加,乳胶膜对水的初始接触角和动态接触角随时间的降低值均呈先增大后减小的趋势,共聚体系中加入适量MPS,通过含氟链段与MPS链段的协同作用,可显著提高涂膜表面性能的稳定性。     

Synthesis and characterization of emulsifier-free trilayer core–shell polysilsesquioxane/polyacrylate/poly(fluorinated acrylate) hybrid latex particles

The trilayer core–shell polysilsesquioxane/polyacrylate/poly(fluorinated acrylate) (PSQ/PA/PFA) hybrid latex particles are successfully prepared, using functional PSQ latex particles with reactive methacryloxypropyl groups synthesized by the hydrolysis and polycondensation of (3-methacryloxypropyl)trimethoxysilane in the presence of a reactive emulsifier as seeds. Transmission electron microscopy (TEM), scanning electron microscopy (SEM) and dynamic light scattering (DLS) confirm that the resultant hybrid latex particles have evident trilayer core–shell structure and a narrow size distribution. The Fourier transform infrared (FTIR) spectra show that fluorinated acrylate monomers are effectively involved in the emulsion copolymerization and formed the fluorine-containing hybrid latex particles. XPS analysis of the obtained hybrid latex film reveals that the intensity of fluorine signal in the film–air interface is higher than that in the film–glass interface. In addition, compared with pure polyacrylate latex film, the obtained fluorine-containing hybrid film shows higher hydrophobicity and thermal stability, and lower surface free energy.     

Synthesis,UV-curing behavior and surface properties of fluorine-containing vinyl ether polymers

Five fluorine-containing vinyl ether monomers were prepared by the reaction between 2-vinyloxy ethanol, a fluorinated alcohol and hexafluorobenzene in the presence of sodium hydride in dimethylformamide. Two representative properties of these monomers, UV-curing behavior initiated by a cationic photo-initiator PAG 201 and surface free energy of coating films, were investigated. Photo-polymerization proceeded both rapidly and completely with a high double-bond conversion （〉 90%） and a fast curing rate （maximum curing time 〈 21 s） for three monomers. The surface energies of the monomers and the resulting polymer films were then investigated. The minimum surface free energy of the UV-cured homopolymer films reaches 7.1 mJ/m2. X-ray photoelectron spectroscopy data show that the low surthce tension is influenced by fluorine content in the soft segments and fluorinated chains＇ migration to the surface. The five monomers exhibit low viscosity, low surface energy, good thermal stability and good photo-polymerization properties, which make them great candidates for UV coating and photoresist applications.     

反应性复合乳液的合成、表征及其交联反应

利用种子半连续乳液聚合方法合成了核层或壳层带有环氧基以及壳层带有羧基的3种不同核/壳结构的乳胶粒子,通过物理共混带环氧基和羧基的乳胶粒子,得到了两种反应性复合乳液.利用透射电镜和激光动态光散射对乳胶粒子进行了表征,其粒径分布较窄,粒径分布的多分散系数为0.062,平均粒径约76 nm,乳胶粒子具有明显的核/壳结构.通过胶膜的凝胶率和膨胀率的测定和红外光谱分析对反应性复合乳液中乳胶粒子的扩散及交联反应进行了研究,并探讨了不同核壳结构复合乳液对涂膜机械性能的影响.研究表明,当反应性复合乳液中的环氧基和羧基分别分布在乳胶粒子的核层和壳层时,有利于聚合物分子链的充分扩散和化学交联反应的进行,从而提高涂膜的物理化学性能,当甲基丙烯酸缩水甘油酯(GMA)含量为10 wt%时,涂膜的拉伸强度达20.3 MPa.     

Na2S2O4 initiated free radical additions of polyfluoroalkyl halides to 4-pentenamides

The free radical additions of fluorine-containing halides to 4-pentenamides initiated by Na₂S₂O₄ were investigated. Both polyfluoroalkyl iodide and ethyl iododifluoroacetate, gave rise to fluorine-containing γ-butyrolactones as the main products while bromides such as ethyl bromodifluoroacetate gave the addition-reduction product. After steric and stereo effects on reaction yields were studied using various substrates, it was concluded that the reactions of 4-pentenamides and polyfluoroalkyl iodides provide one alternative approach to prepare γ-butyrolactones with fluorinated side chains.     

Surface Properties of Fluorinated Acrylate Polymer Latex Films

The surface chemical compositions of fluorinated latex films and the dynamic contact angles of water were determined using X-ray photoelectron spectroscopy (XPS) and a Kruss interface tension measurement, respectively. The surface tensions of the films were calculated by the equation of state approach using the dynamic contact angles, and the effect of temperature on the wetting behavior of these films was investigated. It was shown that the F 1s signal intensity from the outermost surface of these fluorinated latex films was stronger than that from the interior surface of the film and that the surface tension showed a linear decrease with the increase of density of fluorine atoms on the latex film surface to a certain extent. The surface tension rapidly decreased with the increase of fluorinated lateral chains (Rf) content in the copolymer with longer Rf (carbon atom number n>6). The water receding contact angles (θr) on the latex films sharply decreased with the increase of n value, then leveled off nearly at n=10, and remained almost unchanged when n>10. In addition, θr increased more remarkably with the increase of F content in the poly (protonated acrylate- co-fluorinated acrylate) with short hydrocarbon side chains. The water wetting ability of the fluorinate latex films became slightly better only when temperature was more than 40°C.     

Effect of cationic monomer on properties of fluorinated acrylate latex

Cationic fluorinated acrylate latex was prepared via semi-continuous emulsion copolymerization of cationic monomer and other monomers.The resultant latex and its film were characterized with dynamic light scattering detector and contact anglc meter. Influences of amount of DMDAAC on the propcrtics of resultant latex and its film were investigated in detail.Results show that the particle size of the latex has the minimum value and the zeta potential of the latex is increased when the amount of DMDAAC is increased.In addition,the particle size of the latex is unimodal distribution when the amount of DMDAAC is not more than 2.5%. However,the particle size of the latex is bimodal distribution when the amount of DMDAAC is more than 2.5%.The contact angle is varied slightly with the increase of amount of DMDAAC when it is not more than 2.5%.Nevertheless,the contact angle is decreased with the increase of the amount of DMDAAC when it is more than 2.5%.     

Comparison of surface properties of random, block, and graft copolymers having perfluoroalkyl and silicone-containing side chains

Fluorosilicone copolymers of random, block, and graft with both perfluoroalkyl and silicone-containing side chains were synthesized, and their surface properties and surface modification effects on PVC film were compared. It can be confirmed that the fluorosilicone copolymers of random, block, and graft exhibit very low surface free energies of 9-13 dyn/cm, depending on the perfluoroalkyl group content and their molecular structure. The inherent surface free energies of the fluorosilicone copolymers are significantly influenced by their molecular structure and perfluoroalkyl group content. It can also be found that the fluorosilicone copolymers are very effective for lowering surface free energy. The surface free energy of a copolymer/PVC blend strongly varies with perfluoroalkyl group content as well as molecular structure. The molecular structure of a fluorosilicone copolymer is as important as the perfluoroalkyl group content for their inherent surface free energies and surface modification of other polymers.     

水分散体系中甲基丙烯酸甲酯和丙烯酸八氟戊酯嵌段共聚物的合成与表征

在聚合物链上引入氟元素可以赋予聚合物很多优异的性能 ,如良好的热稳定性、化学稳定性、生物相容性和憎水憎油性等 .含氟单体与一般单体共聚是合成含氟共聚物的重要途径 .通过原子转移自由基聚合 (ATRP)不仅可以实现多种单体的控制 (共 )聚合 ,而且可以合成出具有预定分子量、窄分子量分布以及结构明晰聚合物[1] ,我们曾报道了溶液体系中用ATRP方法合成含氟嵌段共聚物[2～ 4] .众所周知 ,大多数含氟聚合物都是通过乳液或悬浮聚合反应合成的 .然而 ,普通的乳液或悬浮聚合难以合成结构和组成可控的聚合物 ,如嵌段共聚物 ,所以近年来 ,水…     

Surface self-segregation, wettability, and adsorption behavior of core-shell and pentablock fluorosilicone acrylate copolymers

The surfaces of films cast from core-shell fluorosilicone acrylate copolymer (BA/MMA/DFHM and BA/MMA/DFHM/MPTMS/D(4)) latexes and linear pentablock fluorosilicone acrylate copolymer (PDMS-b-(PMMA-b-PDFHM)(2)) solutions are intensively investigated and compared by XPS, DCA, AFM, and QCM-D measurements. It is found that the molecular structures and in-solution aggregate structures of these well-defined copolymers have a dramatic influence on the surface structure formation, surface wetting, and adsorption behavior. The PDMS-b-(PMMA-b-PDFHM)(2) film cast from chloroform solution with high concentration of low-density unimers is able to perform as strong surface self-segregation of fluorine-containing groups as core-shell copolymer latex films. The BA/MMA/DFHM/MPTMS/D(4) in the core-shell latex particles exhibits the less pronounced surface self-segregation of silicon-containing groups than PDMS-b-(PMMA-b-PDFHM)(2) due to the occurrence of cross-linking reactions between polysiloxane chains. Indeed, such reactions induce the formation of silica network within the film material, which immobilizes tightly the fluorinated groups on the film surface and thus endows the film with higher surface structural stability for water compared to PDMS-b-(PMMA-b-PDFHM)(2) film with similar surface fluorine concentration and even higher silicon concentration. Still, the PDMS-b-(PMMA-b-PDFHM)(2) film definitely demonstrates higher advancing and receding contact angles for water than BA/MMA/DFHM/MPTMS/D(4) latex film in the case of synergism between surface enrichment of fluorine and silicon.