Microfiltration of protein-cell mixtures with crossflushing or backflushing

Crossflow microfiltration experiments were performed with and without crossflushing or backflushing using yeast suspensions, bovine serum albumin (BSA) solutions, and mixtures of yeast and BSA. Scanning electron microscope (SEM) photographs of the membrane surface were taken before and after crossflushing and backflushing. Backflushing is highly effective, while crossflushing is partially effective, in removing the external cake formed during filtration of yeast suspensions. Crossflushing is completely ineffective and backflushing is only partially effective for removal of internal foulants during filtration of BSA solutions. During backflushing or crossflushing of yeast–BSA mixtures, complete or partial removal of the yeast cake reduces the hydraulic resistance to permeate flow. However, this removal also exposes the primary membrane to internal fouling by BSA, against which neither crossflushing nor backflushing is very effective.     

Oxygen permeation study in a tubular Ba0.5Sr0.5Co0.8Fe0.2O3-δ oxygen permeable membrane

Dense tubular Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCFO) membranes were successfully prepared by the plastic extrusion method. The oxygen permeation flux was determined at different oxygen partial pressures in the shell side and different temperatures between 700 and 900 °C. The oxygen vacancy diffusion coefficients (D_v) at different temperatures were calculated from the dependence of oxygen permeation flux on the oxygen partial pressure term based on the surface current exchange model. No unsteady-state of oxygen permeation flux was observed at the initial stage in our experiments. The reason is the equilibrium time is too short (less than 10 min) to observe the unsteady-state in time. The increase of the helium flow rate can increase the oxygen permeation flux, which is due to the decrease of the oxygen partial pressure in the tube side with increasing of the helium flow rate. The oxygen permeation flux can also be affected by the air flow rate in the shell side when the air flow rate is lower than 150 ml/min. But the oxygen permeation flux is insensitive to the air flow rate when the air flow is higher than 150 ml/min. The membrane tube was operated steadily for 150 h with oxygen permeation flux of 1.12 ml/(cm² min) at 875 °C. X-ray diffraction (XRD) and energy dispersive spectroscopy (EDS) analysis showed that both the surface exposed to air and the surface exposed to helium of the BSCFO membrane tube after permeation for 150 h are similar to the fresh membrane tube in composition and structure. These results indicated that the membrane tube exhibits high structure stability.     

Fabrication and Performance of a Low Operating Pressure Nanofiltration Poly（vinyl chloride） Hollow Fiber Membrane

A low operating pressure nanofiltration membrane is prepared by interfacial polymerization between m-phenylenediamine(MPDA) and trimesoyl chloride(TMC) using PVC hollow fiber membrane as supporting.A series of PVC nanofiltration membranes with different molecular weight cutoff(MWCO) can be obtained by controlling preparation conditions.Chemical and morphological characterization of the membrane surface was carried out by FTIR-ATR and SEM.MWCO was characterized by filtration experiments.The preparation conditions were investigated in detail.At the optimized conditions(40 min air-dried time,aqueous phase containing 0.5% MPDA,0.05% SDS and 0.6% acid absorbent,oil phase containing 0.3% TMC,and 1 min reaction time),under 0.3 MPa,water flux of the gained nanofiltration membrane reaches 17.8 L/m2·h,and the rejection rates of methyl orange and MgSO4 are more than 90% and 60%,respectively.     

Performance of a mixed-conducting ceramic membrane reactor with high oxygen permeability for methane conversion

A mixed-conducting perovskite-type Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCFO) ceramic membrane reactor with high oxygen permeability was applied for the activation of methane. The membrane reactor has intrinsic catalytic activities for methane conversion to ethane and ethylene. C₂ selectivity up to 40–70% was achieved, albeit that conversion rate were low, typically 0.5–3.5% at 800–900°C with a 50% helium diluted methane inlet stream at a flow rate of 34 ml/min. Large amount of unreacted molecular oxygen was detected in the eluted gas and the oxygen permeation flux improved only slightly compared with that under non-reactive air/He experiments. The partial oxidation of methane to syngas in a BSCFO membrane reactor was also performed by packing LiLaNiO/γ-Al₂O₃ with 10% Ni loading as the catalyst. At the initial stage, oxygen permeation flux, methane conversion and CO selectivity were closely related with the state of the catalyst. Less than 21 h was needed for the oxygen permeation flux to reach its steady state. 98.5% CH₄ conversion, 93.0% CO selectivity and 10.45 ml/cm² min oxygen permeation flux were achieved under steady state at 850°C. Methane conversion and oxygen permeation flux increased with increasing temperature. No fracture of the membrane reactor was observed during syngas production. However, H₂-TPR investigation demonstrated that the BSCFO was unstable under reducing atmosphere, yet the material was found to have excellent phase reversibility. A membrane reactor made from BSCFO was successfully operated for the POM reaction at 875°C for more than 500 h without failure, with a stable oxygen permeation flux of about 11.5 ml/cm² min.     

Syngas Production Using an Oxygen-Permeating Membrane Reactor with Cofeed of Methane and Carbon Dioxide

MethaneutilizationhasbeendrawingconsiderableattentionrecentlyduetothelargeamountofnatUralgasavailabletobeupgradedandtheworldwidedemandforlow-costtransportationfuelsl'2.Amongthemanyconversionroutes,partialoxidationofmethane(POM)tosyngasprovedanewwayforthepotentialalternativetotoday'sindustrialsteamreformingprocesses.HoweveT,althoughveryactivecatalystsforthePOMtosyngashavebeenreported,large-scaleplantshavenotyetbeenconstructed.AIargeadiabatictemperatUreriseatthefrontoftheco-bedeasilycausesre…     

膜吸收-再生循环技术捕集CO_2操作性能及其参数优化研究

采用N-甲基二乙醇胺(MDEA)+哌嗪(PZ)复合溶液作为捕集CO2吸收剂,研究了膜吸收-再生循环装置的操作性能,考察了气液流量、吸收剂浓度和再生电压等因素对捕集率和传质通量的影响,采用正交实验方法,优化操作条件,确定最佳操作方案。结果表明,气体流量对捕集率的影响明显大于液体流量的影响;气体流量增大对传质通量影响不明显;吸收剂浓度的增大使传质通量迅速增大,但大于一定值时通量不再增大;正交实验得出最佳操作条件为液体流量110 mL/min、气体流量0.65 L/min、吸收剂总浓度2.5 mol/L和再生电压210 V,捕集率大于95%,传质通量维持在5.86×10-4mol/(m2.s)。     

Comparison between filtrations at fixed transmembrane pressure and fixed permeate flux: application to a membrane bioreactor used for wastewater treatment

Membrane bioreactors for wastewater treatment must operate for long periods without chemical cleaning. This paper investigates the critical flux concept introduced by Field et al. as a means for achieving this goal. Experiments were conducted on a membrane bioreactor containing 600 l of activated sludge, equipped with a 0.25 m² ceramic membrane and located in Compiegne wastewater treatment plant. Hydraulic retention time was set at 24 h and sludge retention time at 60 days, so that suspended solids concentration stabilises at 10 g/l. We conducted two series of tests: at fixed transmembrane pressure (TMP) and at fixed permeate flux, set by a volumetric pump on the permeate. In both cases, velocity was varied from 1 to 5 m/s. In fixed flux tests, the flux was increased by 10 l/h m² increments and the TMP was observed to rise moderately first and then stabilise in about 15 min until a critical value of the flux is reached. Above this critical flux, the TMP rises rapidly and does not stabilise, as in dead-end filtration. The critical flux was found to increase approximately linearly with velocity, reaching about 115 l/h m² at 4 m/s. These data were reproducible at various dates between 30 and 120 days of continuous operation of the bioreactor and permit to know at which flux a membrane bioreactor must be operated. Comparison of constant pressure and constant flux tests under same conditions showed that the critical flux is almost identical to the limiting or pressure independent flux obtained in constant pressure. More generally, constant flux procedure below the critical flux avoids overfouling of the membrane in the initial stage and is more advantageous for membrane bioreactor operation.     

Direct visual observation of yeast deposition and removal during microfiltration

Periodic reverse flow through membranes is an effective technique to remove foulants from microfiltration (MF) membrane surfaces. This work explored direct visual observation (DVO) of yeast deposition and subsequent removal via backwashing and single backpulses using microvideo photography with cellulose-acetate (CA) and Anopore anodised-alumina (AN) MF membranes. Foulant deposited less uniformly on the surfaces of the CA membranes than on the AN membrane surfaces during forward filtration. Foulant cake layers of approximately 30 μm thickness formed on both membranes after forward filtration for 1–2 h, leading to fouled-membrane fluxes of only 15–25% of the clean-membrane fluxes.Foulant was removed by reverse flow from the CA membrane surfaces in clumps. The time constant for foulant removal was determined from photomicrographs to be approximately 0.2 s, and 95% of the membrane surface was cleaned within 1 s of backpulsing, resulting in 95% recovery of the initial flux. The foulant cake was also removed from the AN membranes in clumps, though much of the membrane remained covered in a monolayer of yeast. The flux through the membrane covered with a full monolayer was determined during forward filtration to be about 70% of the clean membrane flux.A model for flux recovery is proposed which takes into account the fraction of the membrane surface which is completely cleaned as well as the fraction which remains covered in a foulant monolayer. The predicted and experimentally-determined recovered fluxes as a function of backpulse duration are in very good agreement.     

混合导体透氧膜反应器中甲烷部分氧化反应的催化行为(英文)

应用组成为Ba0.5Sr0.5Co0.8Fe0.2O3-(的钙钛矿型混合导体陶瓷膜制成膜反应器。该膜在进行氧分离的同时具有活化甲烷氧化偶联的催化功能。随着温度升高和膜的富氧端氧分压的增大,透氧量有所增加。在空气、氦气的氧分压梯度下,850(C,膜厚度为1.5 mm时,JO2可达到1.2 mL/(cm3(min)。同时在800(C~900(C温度范围内,该膜对于甲烷转化为乙烷和乙烯一般只具有0.5%~3.5%的低转化率,而选择性可达40%~70%。在反应尾气中发现了大量的未反应的分子氧,说明过量的氧与甲烷未经催化反应的气相反应导致了C2的选择性相对较低。OCM膜反应模式情况下的透氧量与空气、氦气梯度情况下的透氧量相比只有微小增加,这与POM膜反应模式情况下透氧量大量增加显著不同。     

Mass transfer in osmotic membrane distillation

Osmotic membrane distillation is a novel athermal membrane process that facilitates the maximum concentration of liquid foods under mild operating conditions. In the present study, the effect of various process parameters such as type, concentration and flow rate of the osmotic agent; type (polypropylene membranes) and pore size (0.05 and 0.2 μm) of the membrane; temperature with respect to transmembrane flux was studied. Experiments were performed with real systems (pineapple/sweet lime juice) in a flat membrane module. Osmotic agents namely sodium chloride and calcium chloride at varying concentrations are employed. For both the osmotic agents, higher transmembrane flux was observed at maximum osmotic agent concentration. In comparison with sodium chloride, higher transmembrane flux was observed in case of calcium chloride. A mass transfer-in-series resistance model has been employed, considering the resistance offered by the membrane as well the boundary layers (feed and brine sides) in case of real systems for the first time. The model could predict the variation of transmembrane flux with respect to different process parameters.     

Factors affecting membrane fouling reduction by surface modification and backpulsing

Several factors affecting microfiltration membrane fouling and cleaning, including backpulsing, crossflushing, backwashing, particle size, membrane surface chemistry, and ionic strength, were investigated with suspensions of latex beads. Approximately two-fold permeate volume enhancements over 1 h of filtration were obtained by using water or gas backpulsing, and 50% enhancement was obtained with crossflushing, for filtration of 1.0 μm diameter carboxylate modified latex (CML) particles using unmodified polypropylene (PP) membranes of 0.3 μm nominal pore diameter. When 0.2 μm diameter CML particles or mixtures of 1.0 and 0.2 μm CML particles were used, however, the average flux decreased 60% compared with using 1.0 μm CML particles for experiments with or without backpulsing.PP membranes were rendered hydrophilic with neutral or positively on negatively charged surfaces by grafting monomers of poly(ethylene glycol 200) monomethacrylate (PEG200MA), dimethyl aminoethyl methacrylate (DMAEMA), or acrylic acid (AA), respectively, to the base PP membranes. Filtration experiments show that fouling is not strongly dependent on membrane surface chemistry for filtration of 1.0 μm CML particles without backpulsing. With backpulsing, however, a 10% increase and a 20% decrease of permeate volumes collected in 1 h were observed when the CML particles and the membranes had like charges and opposite charges, respectively, compared to the permeate collected with the unmodified membrane. Using the PP membranes modified with AA, permeate volumes with backpulsing decreased 30 and 40% when NaCl concentrations of 0.01 and 0.1 M, respectively, were added to the feed. However, the permeate volumes did not vary significantly with changing ionic strength for filtration without backpulsing.     

高频红外吸收法测定钽粉、铌粉和碳化钽中的碳

用HCS-140型高频红外碳硫分析仪测定钽粉、铌粉、碳化钽中的碳,进行了助熔剂、称样量、氧气流量试验,在不需测硫的情况下,采用铜和钨作助熔剂、称样量为0．5g、氧气流量为2L／min时,测定结果满足分析要求。     

Concentration and temperature polarization effects during osmotic membrane distillation

Pineapple juice is one of the popular fruit juice due to its pleasant aroma and flavor. Concentration of clarified pineapple juice was carried out by osmotic membrane distillation in a plate and frame membrane module. Concentration and temperature polarization effects are found to have significant role on flux reduction during osmotic membrane distillation process. The contribution of these polarization effects on reduction of the driving force (in turn the flux) at various process conditions such as osmotic agent concentration (2–10 mol/kg (1 molality = 1 mol/kg)), flow rate (25–100 ml/min) of feed and osmotic agent are studied. Concentration polarization has more significant effect on flux reduction when compared to temperature polarization. The experimental fluxes were in good agreement with theoretical fluxes when calculated by considering both concentration and temperature polarization effects. The pineapple juice was concentrated up to a total soluble solids content of 62°Brix at ambient temperature.     

Visualization and characterization of SPG membrane emulsification

Shirasu-porous-glass (SPG) membrane emulsification is highly attractive for various fields of foods, cosmetics, and pharmaceuticals because this technique produces monodispersed emulsions. However, there are few reports on the observation of membrane emulsification at the membrane surface. In the present work, we aimed to visualize the membrane emulsification using a microscope high-speed camera system. The direct observation made it possible to measure the mean rate of droplet formation and the percentage of active pores. The mean rate of droplet formation ranged 0.3–12 s⁻¹ and the percentage of active pores ranged 0.3–0.5% under the dispersed-phase flux of 0.58×10⁻⁶–5.8×10⁻⁶ m³/(m² s). We also observed that the droplets were formed without continuous-phase flow and the droplets were also formed by shear force at the continuous-phase flow under different experimental conditions. The balance among the dispersed-phase flux and the continuous-phase flow velocity influenced droplet formation.     

Determination of UV-filters in sunscreens by HPLC

Simultaneous determination of six internationally authorised organic UV-filters in sunscreen formulations was performed by HPLC with UV spectrophotometric detection. The filters determined were: sulisobenzone, oxybenzone, octyl dimethyl PABA, octyl methoxycinnamate, octyl salicylate and homosalate. A C18 stationary phase and a mobile phase of ethanol water acetic acid (70:29.5:0.5) were used with a flow rate of 0.5 mL/min. UV measurements were carried out at 313 nm. The time required for the analysis was 25 min and the limits of detection were between 0.2 and 2 mg/L, except for sulisobenzone, which gave a limit of detection of 20 mg/L. The procedure proposed provides an accurate, fast and green analytical method, that does not involve toxic organic solvents.     

Novel Ba_(0.5)Sr_(0.5)Fe_(0.8)Zn_(0.2)O_(3-δ) membranes for POM

A novel cobalt-free perovskite based on Ba_(0.5)Sr_(0.5)Fe_(0.8)Zn_(0.2)O_(3-δ)(BSFZ)were prepared by EDTA-citric acid method.The lattice constants of the BSFZ perovskite were characterized by in situ high-temperature X-ray diffraction(HTXRD).The thermal expansion coefficient of BSFZ is 10.5×10~(-6)K~(-1),which is lower than that of cobalt-based perovskite materials.The BSFZ membrane was also used to construct reactors for the partial oxidation of methane(POM)to syngas.Results show that the BSFZ membrane...     

Effect of backwash on the performance of submerged membrane filtration

Particles with a mean diameter of 5 μm were filtered by a ceramic tubular membrane to study the effects of backwash on the performance of submerged membrane filtration. A periodic backwash can completely remove the formed cake, diminishing a part of membrane internal fouling, and, therefore, recover the filtration flux. In a membrane-blocking/cake formation comparable filtration system, the filtration resistance due to membrane-internal fouling is over twice as high as that due to cake formation. The irreversible filtration resistance increases progressively during operation, and it can be regressed to a power-type empirical relationship. Filtration period data were analyzed using blocking models. Membrane blocking occurs in the early filtration periods and is followed by cake filtration. The filtration flux can be simulated by employing blocking models and empirical equations for filtration resistance. The backwash effectiveness was examined by comparing filtrate productivity and washing efficiency. The calculated results of productivity under various backwash durations agree well with experimental data. An increase in backwash flux or duration leads to higher productivity, when the duration is shorter than 2 min; however, the productivity may be decreased with an increase of backwash duration due to the back pumping of more filtrate. A longer filtration time in each cycle results in higher backwash efficiency since a formed cake may efficiently prevent further membrane pore clogging and is more easily removed by a backwash. The optimal backwash conditions can be determined appropriately by the proposed method, with respect to both backwash efficiency and filtrate productivity.     

Parameters influencing transport across conducting electroactive polymer membranes

The parameters which influence electrochemically facilitated transport of electroinactive ions across conducting electroactive polymer membranes have been investigated. The design of membranes and the materials used as well as transport cells and systems have been addressed to improve selectivity and flux. Polypyrrole-para-toluenesulfonate (PPy-pTS) was compared with the copolymer of pyrrole with 3-carboxy-4-methylpyrrole (PPy/PCMP-pTS) and their different chemistries resulted in different membrane selectivities for ions. Platinum mesh was found to be the most suitable auxiliary electrode material and its placement in the cell chamber(s) facilitated ion incorporation/expulsion at the membrane working electrode. This enhanced the flux of ion transport. The flux can also further enhanced by narrowing the distance between the membrane working electrode and the platinum mesh auxiliary electrode(s), and/or by stirring to improve the hydrodynamics. An alternative cell design, namely a dual membrane flow through cell, also proved to be more efficient for ion transport. Good connection geometry to the membrane as well as the application of a square wave pulsed potential waveform to the membrane was found to be essential for achieving high and sustainable flux in ion transport.     

Flux enhancement in crossflow filtration using an unsteady jet

This paper deals with the influence of a new type of unsteadiness in the flow on the permeate flux in crossflow filtration. A pneumatically controlled valve generates intermittent jets from the main flow leading to the formation of large vortices moving downstream along the tubular membrane. The experimental study was carried out by filtering a bentonite suspension through an ultrafiltration mineral membrane. Flux time measurements were taken under steady and unsteady operating conditions. The unsteadiness leads to a permeate flux more than two times higher than in the usual filtration processes.     

Reversibility of fouling formed in activated sludge filtration

This paper investigates the reversibility of membrane fouling by activated sludge in a membrane bioreactor equipped with a 0.1 μm pore ceramic membrane. The membrane was submitted to a series of tests in which the permeate flux, the transmembrane pressure (TMP) or the circulation velocity were successively varied in cycles by step increments or decreases. When the permeate flux is set below the critical flux, the TMP remains stable and fouling is reversible. On the contrary, when the critical flux is exceeded, the TMP increases and does not stabilize, as in dead-end filtration. The fouling formed is partly irreversible when the flux is lowered again. When the TMP is first increased up to 400 kPa and then decreased back at constant velocity, no hysteresis is found on the flux–TMP graph, showing that fouling is reversible in this case. Velocity cycles were performed by first lowering the velocity from 5 to 1 m/s and raising it again to 5 m/s. In this case again, the fouling induced by reducing the velocity was found to be reversible. However, when the same pressure and velocity cycle tests were performed with activated sludge collected in the aeration tank of a classical wastewater treatment plant, fouling was found to be partly irreversible, showing that the cake formed in the absence of shearing is much more cohesive. In the final part of the paper, we tested a hydrodynamic method of fouling control consisting in alternating short periods of filtration (1–4 s) and short periods of washing (1 or 2 s) at low TMP and high velocity. This method yielded to a 20% permeate flux increase with a 10% reduction in hydraulic energy consumption for classical plant activated sludge.