Electrochemical dissolution of Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> in acid solutions

The present study deals with the electrochemical reductive dissolution of Mn₃O₄, which was added to carbon-paste electroactive electrodes (CPEEs) in acid solutions. It was found that in the experimental conditions the thermodynamically stable form of manganese was . Kinetic features of the electrochemical reductive dissolution of Mn₃O₄, which was realized under potential cycling conditions (+1.0 V→−0.7 V→+1.0 V), were determined by the electrode polarization direction. It was shown that the cathodic reduction of Mn₃O₄ was accomplished in three stages. Manganese was dissolved in the supporting solution only at the third stage. The first two stages involved solid-phase reactions. The anodic cycling stage included an active dissolution of Mn₃O₄ and the lower manganese oxide (MnO) accumulated on the electrode surface during the cathodic reduction.     

2-pyrrolidone - capped Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> nanocrystals

Water-soluble Mn₃O₄ nanocrystals have been prepared through thermal decomposition in a high temperature boiling solvent, 2-pyrrolidone. The final product was characterized with XRD, SEM, TEM, FTIR and Zeta Potential measurements. Average crystallite size was calculated as ∼15 nm using XRD peak broadening. TEM analysis revealed spherical nanoparticles with an average diameter of 14±0.4 nm. FTIR analysis indicated that 2-pyrrolidone coordinates with the Mn₃O₄ nanocrystals only via O from the carbonyl group, thus confining their growth and protecting their surfaces from interaction with neighboring particles.      

Rational design of double-confined Mn<Subscript>2</Subscript>O<Subscript>3</Subscript>/S@Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocube cathodes for lithium-sulfur batteries

Due to the high specific capacities and environmental benignity, lithium-sulfur (Li-S) batteries have shown fascinating potential to replace the currently dominant Li-ion batteries to power portable electronics and electric vehicles. However, the shuttling effect caused by the dissolution of polysulfides seriously degrades their electrochemical performance. In this paper, Mn₂O₃ microcubes are fabricated to serve as the sulfur host, on top of which Al₂O₃ layers of 2 nm in thickness are deposited via atomic layer deposition (ALD) to form Mn₂O₃/S (MOS) @Al₂O₃ composite electrodes. The MOS@Al₂O₃ electrode delivers an excellent initial capacity of 1012.1 mAh g^?1 and a capacity retention of 78.6% after 200 cycles at 0.5 C, and its coulombic efficiency reaches nearly 99%, giving rise to much better performance than the neat MOS electrode. These findings demonstrate the double confinement effect of the composite electrode in that both the porous Mn₂O₃ structure and the atomic Al₂O₃ layer serve as the spacious host and the protection layer of sulfur active materials, respectively, for significantly improved electrochemical performance of the Li-S battery.     

Magnetic nanoparticles (Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> &amp; Co<Subscript>3</Subscript>O<Subscript>4</Subscript>) and their applications in urea biosensing

Nanobiotechnology has opened a new and exciting opportunities for exploring urea biosensor based on magnetic nanoparticles (NPs) mainly Fe₃O₄ and Co₃O₄. These NPs have been extensively exploited to develop biosensors with stability, selectivity, reproducibility and fast response time. This review gives an overview of the development of urea biosensor based on Fe₃O₄ and Co₃O₄ for in vitro diagnostic applications along with significant improvements over the last few decades. Additionally, effort has been made to elaborate properties of magnetic nanoparticles (MNPs) in biosensing aspects. It also gives details of recent developments in hybrid nanobiocomposite based urea biosensor.     

Preparation and characterization of high specific surface area Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> from electrolytic manganese residue

Mn₃O₄ powders have been produced from Electrolytic Manganese Residue (EMR). After leaching of EMR in sulfuric acid, MnSO₄ solution containing various ions was obtained. Purifying the solution obtained and then adding aqueous alkali to the purified MnSO₄ solution, Mn(OH)₂ was prepared. Two methods were employed to produce Mn₃O₄. One way was oxidation of Mn(OH)₂ in aqueous phase under atmosphere pressure to obtain Mn₃O₄. The other way was roasting Mn(OH)₂ precursors in the range of 500°C to 700°C. The prepared samples were investigated by using several techniques including X-ray powder diffraction (XRD), Fourier Transformation Infra-Red (FTIR) spectra, and Brunauer-Emmett-Teller (BET) specific surface area instrument. Particle distribution and magnetic measurements were carried out on laser particle size analyzer, vibrating sample magnetometer (VSM). Through XRD, FTIR and determination of total Mn content (TMC), the products prepared were confirmed to be a single phase Mn₃O₄. BET specific surface areas can reach to 32 m² g⁻¹. The results indicated that products synthesized by aqueous solution oxidation method had higher specific surface areas and smaller particle size than those prepared by means of roasting. However the products prepared using the above two methods showed no obvious differences in magnetic property.      

Mn<Subscript>3</Subscript>O<Subscript>4</Subscript>/carbon nanotubes nanocomposites as improved anode materials for lithium-ion batteries

Mn₃O₄ and Mn₃O₄ (140)/CNTs have been investigated as high-capacity anode materials for lithium-ion batteries (LIBs) applications. Nanoparticle Mn₃O₄ samples were synthesized by hydrothermal method using Mn(Ac)₂ and NH₃·H₂O as the raw materials and characterized by XRD, TG, EA, TEM, and SEM. Its electrochemical performances, as anode materials, were evaluated by galvanostatic discharge-charge tests. The Mn₃O₄ (140)/CNTs displays outstanding electrochemical performances, such as high initial capacity (1942 mAh g^?1), stable cycling performance (1088 mAh g^?1 and coulombic efficiency remain at 97% after 60 cycles) and great rate performance (recover 823 mAh g^?1 when return to initial current density after 44 cycles). Compared to pure Mn₃O₄ (140), the improving electrochemical performances can be attributed to the existence of very conductive CNTs. The Mn₃O₄ (140)/CNTs with excellent electrochemical properties might find applications as highly effective materials in electromagnetism, catalysis, microelectronic devices, etc. The process should also offer an effective and facile method to fabricate many other nanosized metallic oxide/CNTs nanocomposites for low-cost, high-capacity, and environmentally benign materials for LIBs.     

Comparison of the Solubility of ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>, Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> in High Temperature Water

As the solubility is a direct measure of stability, this study compares the solubilities of ZnFe₂O₄, Fe₃O₄ and Fe₂O₃ in high temperature water. Through literature analysis and formula derivation, it is shown that it is reasonable to assume ZnFe₂O₄ and Fe(OH)₃ coexist when ZnFe₂O₄ is dissolved in water. Results indicated that the solubility of ZnFe₂O₄ is much lower than that of Fe₂O₃ or Fe₃O₄. The low solubility of ZnFe₂O₄ indicates that it is more protectively stable as an anticorrosion phase. Moreover, the gap between the solubility of ZnFe₂O₄ and that of Fe₃O₄ or Fe₂O₃ was enlarged with an increase of temperature. This means that ZnFe₂O₄ is more protective at higher temperatures. Further analysis indicated that with the increase of temperature, the solubility of ZnFe₂O₄ changed little while those of Fe₂O₃ or Fe₃O₄ changed a lot. Little change of the solubility of ZnFe₂O₄ with increase of temperature showed that ZnFe₂O₄ is stable. The very low and constant solubility of ZnFe₂O₄ suggests that it is more protective than Fe₂O₃ and Fe₃O₄, especially in water at higher temperature.     

Preparation and electrochemical performance of nano-structured Li<Subscript>2</Subscript>Mn<Subscript>4</Subscript>O<Subscript>9</Subscript> for supercapacitor

Nano-structured spinel Li₂Mn₄O₉ powder was prepared via a combustion method with hydrated lithium acetate (LiAc·2H₂O), manganese acetate (MnAc₂·4H₂O), and oxalic acid (C₂H₂O₄·2H₂O) as raw materials, followed by calcination of the precursor at 300 °C. The sample was characterized by X-ray diffraction, scanning electron microscope, and energy-dispersive X-ray spectroscopy techniques. Electrochemical performance of the nano-Li₂Mn₄O₉ material was studied using cyclic voltammetry, ac impedance, and galvanostatic charge/discharge methods in 2 mol L⁻¹ LiNO₃ aqueous electrolyte. The results indicated that the nano-Li₂Mn₄O₉ material exhibited excellent electrochemical performance in terms of specific capacity, cycle life, and charge/discharge stability, as evidenced by the charge/discharge results. For example, specific capacitance of the single Li₂Mn₄O₉ electrode reached 407 F g⁻¹ at the scan rates of 5 mV s⁻¹. The capacitor, which is composed of activated carbon negative electrode and Li₂Mn₄O₉ positive electrode, also exhibits an excellent cycling performance in potential range of 0–1.6 V and keeps over 98% of the maximum capacitance even after 4,000 cycles.     

Glass formation in the CaO-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> and SrO-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-B<Subscript>2</Subscript>O<Subscript>3</Subscript> systems

A physicochemical study of glasses based on the MO-Bi₂O₃-B₂O₃ and SrO-Bi₂O₃-B₂O₃ systems was performed. Glass formation regions were found. The structural and optical properties, as well as the thermal behavior of the glasses, were studied.     

Synthesis,crystal structure,and vibrational spectra of M<Subscript>4</Subscript>V<Subscript>2</Subscript>O<Subscript>3</Subscript>(SO<Subscript>4</Subscript>)<Subscript>4</Subscript> (M = K,Rb, Cs)

Synthesis was performed and physicochemical properties were studied for the M₄V₂O₃(SO₄)₄ complexes, where M = K, Rb, or Cs. Their crystal structures were determined using the set of data from X-ray diffraction and neutron diffraction studies. All compounds crystallize in a triclinic lattice (space group \(P\bar 1\), Z = 2) with the parameters: a = 7.7688(2), 7.8487(1), 8.1234(1) Å; b = 10.4918(3), 10.8750(2), 11.1065(1) Å; c = 11.9783(4), 12.1336(2), and 11.8039(1) Å; α = 76.600(2)°, 77.910(1)°, 79.589(1)°; β = 75.133(2)°, 75.718(1)°, 87.939(1)°; γ = 71.285(2)°, 72.189(1)°, 75.567(1)°; V = 881.78(5), 945.42(3), 1014.34(2) ų for K, Rb, Cs, respectively. The structure of M₄V₂O₃(SO₄)₄ was found to be formed by discrete complex anions V₂O₃(SO₄) ₄ ^4? incorporating two oxygen-bridged vanadium atoms in a distorted octahedral oxygen environment. The sulfate groups are coordinated by the vanadium atoms in the chelating mode with a large scatter of S-O interatomic distances and OSO angles. Every VO₆ octahedron has a short terminal vanadium-oxygen bond with a length of about 1.6Å. The V₂O₃(SO₄) ₄ ^4? complex anions in potassium and rubidium compounds differ from that in Cs₄V₂O₃(SO₄)₄ in the type of symmetry and mutual spatial orientation. The vibrational spectra were presented and interpreted in line with the structural analysis data.     

La<Subscript>2</Subscript>M<Stack><Subscript>3</Subscript><Superscript>II</Superscript></Stack>Mn<Subscript>4</Subscript>O<Subscript>12</Subscript> (M = Mg,Ca, Sr,or Ba) manganites: Synthesis and X-ray diffraction study

La₂M ₃ ^II Mn₄O₁₂ (M = Mg, Ca, Sr, or Ba) manganites have been synthesized by ceramic technology from lanthanum oxide, manganese(III) oxide, and magnesium, calcium, strontium, or barium carbonate. X-ray powder diffraction shows that these compounds crystallize in cubic perovskite space group Pm3m.     

Electrochemical properties of nano-crystalline LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> synthesized by polymer-pyrolysis method

LiNi_0.5Mn_1.5O₄ powders were prepared through polymer-pyrolysis method. XRD and TEM analysis indicated that the pure spinel structure was formed at around 450 °C due to the very homogeneous intermixing of cations at the atomic scale in the starting precursor in this method, while the well-defined octahedral crystals appeared at a relatively high calcination temperature of 900 °C with a uniform particle size of about 100 nm. When cycled between 3.5 and 4.9 V at a current density of 50 mA/g, the as prepared LiNi_0.5Mn_1.5O₄ delivered an initial discharge capacity of 112.9 mAh/g and demonstrated an excellent cyclability with 97.3% capacity retentive after 50 cycles.     

Thermodynamic properties of the system MgO-B<Subscript>2</Subscript>O<Subscript>3</Subscript> melts

Vaporization processes of melts of the system MgO-B₂O₃ at 1640 K were studied by high-temperature mass spectrometry, and thermodynamic properties (activity, chemical potentials of MgO and B₂O₃, and also the corresponding excess values) were determined. Considerable negative deviations from the ideal behavior in the melts of the studied system are observed. The termodynamic properties of the system MgO-B₂O₃ can be calculated within the framework of the lattice theory of associated solutions.     

Thermodynamic properties of silicate glasses and melts: V. Systems CaB<Subscript>2</Subscript>O<Subscript>4</Subscript>-CaSiO<Subscript>3</Subscript> and Ca<Subscript>2</Subscript>B<Subscript>2</Subscript>O<Subscript>5</Subscript>-CaSiO<Subscript>3</Subscript>

Thermodynamic properties of melts of the CaB₂O₄-CaSiO₃ and Ca₂B₂O₅-CaSiO₃ systems were determined by the method of high-temperature mass-spectrometry. The melts of these systems are characterized by negative deviations from the ideal behavior at 1800 K.     

Thermal oxide synthesis and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanorods and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanowires

Fe₃O₄ nanorods and Fe₂O₃ nanowires have been synthesized through a simple thermal oxide reaction of Fe with C₂H₂O₄ solution at 200–600°C for 1 h in the air. The morphology and structure of Fe₃O₄ nanorods and Fe₂O₃ nanowires were detected with powder X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The influence of temperature on the morphology development was experimentally investigated. The results show that the polycrystals Fe₃O₄ nanorods with cubic structure and the average diameter of 0.5–0.8 μm grow after reaction at 200–500°C for 1 h in the air. When the temperature was 600°C, the samples completely became Fe₂O₃ nanowires with hexagonal structure. It was found that C₂H₂O₄ molecules had a significant effect on the formation of Fe₃O₄ nanorods. A possible mechanism was also proposed to account for the growth of these Fe₃O₄ nanorods. Supported by the Fund of Weinan Teacher’s University (Grant No. 08YKZ008), the National Natural Science Foundation of China (Grant No. 20573072) and the Doctoral Fund of Ministry of Education of China (Grant No. 20060718010)     

Insights into the selective catalytic reduction of NO by NH<Subscript>3</Subscript> over Mn<Subscript>3</Subscript>O<Subscript>4</Subscript>(110): a DFT study coupled with microkinetic analysis

Nitric oxide (NO_x), as one of the main pollutants, can contribute to a series of environmental problems, and to date the selective catalytic reduction (SCR) of NO_x with NH₃ in the presence of excess of O₂ over the catalysts has served as one of the most effective methods, in which Mn-based catalysts have been widely studied owing to their excellent low-temperature activity toward NH₃-SCR. However, the related structure-activity relation was not satisfactorily explored at the atomic level. By virtue of DFT+U calculations together with microkinetic analysis, we systemically investigate the selective catalytic reduction process of NO with NH₃ over Mn₃O₄(110), and identify the crucial thermodynamic and kinetic factors that limit the catalytic activity and selectivity. It is found that NH₃ prefers to adsorb on the Lewis acid site and then dehydrogenates into NH₂* assisted by either the two- or three-fold lattice oxygen; NH₂* would then react with the gaseous NO to form an important intermediate NH₂NO that prefers to convert into N₂O rather than N₂ after the sequential dehydrogenation, while the residual H atoms interact with O₂ and left the surface in the form of H₂O. The rate-determining step is proposed to be the coupling reaction between NH₂* and gaseous NO. Regarding the complex surface structure of Mn₃O₄(110), the main active sites are quantitatively revealed to be O_3c and Mn_4c.     

Promoted porous Co<Subscript>3</Subscript>O<Subscript>4</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts for ammonia decomposition

Transition metal catalysts have been considerably used for NH₃ decomposition because of the potential application in CO_x-free H₂ generation for fuel cells. However, most transition metal catalysts prepared via traditional synthetic approaches performed the inferior stability due to the agglomeration of active components. Here, we adopted an efficient method, aerosol-assisted self-assembly approach (AASA), to prepare the optimized cobalt-alumina (Co₃O₄-Al₂O₃) catalysts. The Co₃O₄-Al₂O₃ catalysts exhibited excellent catalytic performance in the NH3 decomposition reaction, which can reach 100% conversion at 600 °C and maintain stable for 72 h at a gaseous hourly space velocity (GHSV) of 18000 cm³ g_cat^?1 h^?1. The catalysts were characterized by various techniques including transmission electron microscope (TEM), scanning electron microscope (SEM), nitrogen sorption, temperature-programmed reduction by hydrogen (H₂-TPR), ex-situ/in-situ Raman and ex-situ/in-situ X-ray diffraction (XRD) to obtain the information about the structure and property of the catalysts. H₂-TPR and in-situ XRD results show that there is strong interaction between the cobalt and alumina species, which influences the redox properties of the catalysts. It is found that even a low content of alumina (10 at%) is able to stabilize the catalysts due to the adequate dispersion and rational interaction between different components, which ensures the high activity and superior stability of the cobalt-alumina catalysts.     

Manganites NdMg<Stack><Subscript>3</Subscript><Superscript>I</Superscript></Stack>Mg<Subscript>3</Subscript>Mn<Subscript>4</Subscript>O<Subscript>12</Subscript> (M<Superscript>I</Superscript> = Li,Na, K): X-ray diffraction data

NdLi₃Mg₃Mn₄O₁₂, NdNa₃Mg₃Mn₄O₁₂, and NdK₃Mg₃Mn₄O₁₂ manganites were synthesized for the first time by solid phase reactions of neodymium(III) and manganese(III) oxides with lithium, sodium, potassium, and magnesium carbonates. X-ray diffraction showed that the compounds crystallized in the tetragonal crystal system. Their unit cell parameters were determined.     

Co-precipitation spray-drying synthesis and electrochemical performance of stabilized LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode materials

In this paper, the LiNi_0.5Mn_1.5O₄ cathode materials of lithium-ion batteries are synthesized by a co-precipitation spray-drying and calcining process. The use of a spray-drying process to form particles, followed by a calcination treatment at the optimized temperature of 750 °C to produce spherical LiNi_0.5Mn_1.5O₄ particles with a cubic crystal structure, a specific surface area of 60.1 m² g^?1, a tap density of 1.15 g mL^?1, and a specific capacity of 132.9 mAh g^?1 at 0.1 C. The carbon nanofragment (CNF) additives, introduced into the spheres during the co-precipitation spray-drying period, greatly enhance the rate performance and cycling stability of LiNi_0.5Mn_1.5O₄. The sample with 1.0 wt.% CNF calcined at 750 °C exhibits a maximum capacity of 131.7 mAh g^?1 at 0.5 C and a capacity retention of 98.9% after 100 cycles. In addition, compared to the LiNi_0.5Mn_1.5O₄ material without CNF, the LiNi_0.5Mn_1.5O₄ with CNF demonstrates a high-rate capacity retention that increases from 69.1% to 95.2% after 100 cycles at 10 C, indicating an excellent rate capability. The usage of CNF and the synthetic method provide a promising choice for the synthesis of a stabilized LiNi_0.5Mn_1.5O₄ cathode material.

Open image in new window

Graphical Abstract Micro/nanostructured LiNi_0.5Mn_0.5O₄ cathode materials with enhanced electrochemical performances for high voltage lithium-ion batteries are synthesized by a co-precipitation spray-drying and calcining routine and using carbon nanofragments (CNFs) as additive.

     

Physical and electrochemical properties of LiFe<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> spinel synthesized by different methods

The study deals with the synthesis and comparison of physicochemical properties of LiFe_0.5Mn_1.5O₄ based cathode materials synthesized by the standard ceramic and the auto-ignition method.